/*
- * linux/drivers/ide/pci/piix.c Version 0.46 December 3, 2006
- *
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
- * Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
- * PIO mode setting function for Intel chipsets.
- * For use instead of BIOS settings.
- *
- * 40-41
- * 42-43
- *
- * 41
- * 43
- *
- * | PIO 0 | c0 | 80 | 0 | piix_tune_drive(drive, 0);
- * | PIO 2 | SW2 | d0 | 90 | 4 | piix_tune_drive(drive, 2);
- * | PIO 3 | MW1 | e1 | a1 | 9 | piix_tune_drive(drive, 3);
- * | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
- *
- * sitre = word40 & 0x4000; primary
- * sitre = word42 & 0x4000; secondary
- *
- * 44 8421|8421 hdd|hdb
- *
- * 48 8421 hdd|hdc|hdb|hda udma enabled
- *
- * 0001 hda
- * 0010 hdb
- * 0100 hdc
- * 1000 hdd
- *
- * 4a 84|21 hdb|hda
- * 4b 84|21 hdd|hdc
+ * Documentation:
*
- * ata-33/82371AB
- * ata-33/82371EB
- * ata-33/82801AB ata-66/82801AA
- * 00|00 udma 0 00|00 reserved
- * 01|01 udma 1 01|01 udma 3
- * 10|10 udma 2 10|10 udma 4
- * 11|11 reserved 11|11 reserved
- *
- * 54 8421|8421 ata66 drive|ata66 enable
- *
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x40, ®40);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x42, ®42);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x44, ®44);
- * pci_read_config_byte(HWIF(drive)->pci_dev, 0x48, ®48);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x4a, ®4a);
- * pci_read_config_byte(HWIF(drive)->pci_dev, 0x54, ®54);
- *
- * Documentation
* Publically available from Intel web site. Errata documentation
* is also publically available. As an aide to anyone hacking on this
* driver the list of errata that are relevant is below.going back to
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
-#include <linux/ioport.h>
#include <linux/pci.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
-#include <linux/delay.h>
#include <linux/init.h>
#include <asm/io.h>
static int no_piix_dma;
/**
- * piix_ratemask - compute rate mask for PIIX IDE
- * @drive: IDE drive to compute for
+ * piix_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Returns the available modes for the PIIX IDE controller.
+ * Set the interface PIO mode based upon the settings done by AMI BIOS.
*/
-
-static u8 piix_ratemask (ide_drive_t *drive)
-{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- u8 mode;
-
- switch(dev->device) {
- case PCI_DEVICE_ID_INTEL_82801EB_1:
- mode = 3;
- break;
- /* UDMA 100 capable */
- case PCI_DEVICE_ID_INTEL_82801BA_8:
- case PCI_DEVICE_ID_INTEL_82801BA_9:
- case PCI_DEVICE_ID_INTEL_82801CA_10:
- case PCI_DEVICE_ID_INTEL_82801CA_11:
- case PCI_DEVICE_ID_INTEL_82801E_11:
- case PCI_DEVICE_ID_INTEL_82801DB_1:
- case PCI_DEVICE_ID_INTEL_82801DB_10:
- case PCI_DEVICE_ID_INTEL_82801DB_11:
- case PCI_DEVICE_ID_INTEL_82801EB_11:
- case PCI_DEVICE_ID_INTEL_ESB_2:
- case PCI_DEVICE_ID_INTEL_ICH6_19:
- case PCI_DEVICE_ID_INTEL_ICH7_21:
- case PCI_DEVICE_ID_INTEL_ESB2_18:
- case PCI_DEVICE_ID_INTEL_ICH8_6:
- mode = 3;
- break;
- /* UDMA 66 capable */
- case PCI_DEVICE_ID_INTEL_82801AA_1:
- case PCI_DEVICE_ID_INTEL_82372FB_1:
- mode = 2;
- break;
- /* UDMA 33 capable */
- case PCI_DEVICE_ID_INTEL_82371AB:
- case PCI_DEVICE_ID_INTEL_82443MX_1:
- case PCI_DEVICE_ID_INTEL_82451NX:
- case PCI_DEVICE_ID_INTEL_82801AB_1:
- return 1;
- /* Non UDMA capable (MWDMA2) */
- case PCI_DEVICE_ID_INTEL_82371SB_1:
- case PCI_DEVICE_ID_INTEL_82371FB_1:
- case PCI_DEVICE_ID_INTEL_82371FB_0:
- case PCI_DEVICE_ID_INTEL_82371MX:
- default:
- return 0;
- }
-
- /*
- * If we are UDMA66 capable fall back to UDMA33
- * if the drive cannot see an 80pin cable.
- */
- if (!eighty_ninty_three(drive))
- mode = min_t(u8, mode, 1);
- return mode;
-}
-/**
- * piix_dma_2_pio - return the PIO mode matching DMA
- * @xfer_rate: transfer speed
- *
- * Returns the nearest equivalent PIO timing for the PIO or DMA
- * mode requested by the controller.
- */
-
-static u8 piix_dma_2_pio (u8 xfer_rate) {
- switch(xfer_rate) {
- case XFER_UDMA_6:
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- case XFER_MW_DMA_2:
- case XFER_PIO_4:
- return 4;
- case XFER_MW_DMA_1:
- case XFER_PIO_3:
- return 3;
- case XFER_SW_DMA_2:
- case XFER_PIO_2:
- return 2;
- case XFER_MW_DMA_0:
- case XFER_SW_DMA_1:
- case XFER_SW_DMA_0:
- case XFER_PIO_1:
- case XFER_PIO_0:
- case XFER_PIO_SLOW:
- default:
- return 0;
- }
-}
-
-/**
- * piix_tune_drive - tune a drive attached to a PIIX
- * @drive: drive to tune
- * @pio: desired PIO mode
- *
- * Set the interface PIO mode based upon the settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
- */
-static void piix_tune_drive (ide_drive_t *drive, u8 pio)
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
int is_slave = drive->dn & 1;
int master_port = hwif->channel ? 0x42 : 0x40;
int slave_port = 0x44;
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
-
/*
* Master vs slave is synchronized above us but the slave register is
* shared by the two hwifs so the corner case of two slave timeouts in
master_data |= 0x4000;
master_data &= ~0x0070;
if (pio > 1) {
- /* enable PPE, IE and TIME */
- master_data = master_data | (control << 4);
+ /* Set PPE, IE and TIME */
+ master_data |= control << 4;
}
pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
- slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
+ slave_data &= hwif->channel ? 0x0f : 0xf0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) <<
+ (hwif->channel ? 4 : 0);
} else {
master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
- master_data = master_data | control;
+ master_data |= control;
}
- master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
+ master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
if (is_slave)
}
/**
- * piix_tune_chipset - tune a PIIX interface
- * @drive: IDE drive to tune
- * @xferspeed: speed to configure
+ * piix_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Set a PIIX interface channel to the desired speeds. This involves
- * requires the right timing data into the PIIX configuration space
- * then setting the drive parameters appropriately
+ * Set a PIIX host controller to the desired DMA mode. This involves
+ * programming the right timing data into the PCI configuration space.
*/
-
-static int piix_tune_chipset (ide_drive_t *drive, u8 xferspeed)
+
+static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 maslave = hwif->channel ? 0x42 : 0x40;
- u8 speed = ide_rate_filter(piix_ratemask(drive), xferspeed);
int a_speed = 3 << (drive->dn * 4);
int u_flag = 1 << drive->dn;
int v_flag = 0x01 << drive->dn;
pci_read_config_byte(dev, 0x54, ®54);
pci_read_config_byte(dev, 0x55, ®55);
- switch(speed) {
- case XFER_UDMA_4:
- case XFER_UDMA_2: u_speed = 2 << (drive->dn * 4); break;
- case XFER_UDMA_5:
- case XFER_UDMA_3:
- case XFER_UDMA_1: u_speed = 1 << (drive->dn * 4); break;
- case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_SW_DMA_2: break;
- case XFER_PIO_4:
- case XFER_PIO_3:
- case XFER_PIO_2:
- case XFER_PIO_0: break;
- default: return -1;
- }
-
if (speed >= XFER_UDMA_0) {
+ u8 udma = speed - XFER_UDMA_0;
+
+ u_speed = min_t(u8, 2 - (udma & 1), udma) << (drive->dn * 4);
+
if (!(reg48 & u_flag))
pci_write_config_byte(dev, 0x48, reg48 | u_flag);
if (speed == XFER_UDMA_5) {
} else
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
} else {
+ const u8 mwdma_to_pio[] = { 0, 3, 4 };
+ u8 pio;
+
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
- }
-
- piix_tune_drive(drive, piix_dma_2_pio(speed));
- return (ide_config_drive_speed(drive, speed));
-}
-
-/**
- * piix_config_drive_for_dma - configure drive for DMA
- * @drive: IDE drive to configure
- *
- * Set up a PIIX interface channel for the best available speed.
- * We prefer UDMA if it is available and then MWDMA. If DMA is
- * not available we switch to PIO and return 0.
- */
-
-static int piix_config_drive_for_dma (ide_drive_t *drive)
-{
- u8 speed = ide_dma_speed(drive, piix_ratemask(drive));
- /*
- * If no DMA speed was available or the chipset has DMA bugs
- * then disable DMA and use PIO
- */
- if (!speed)
- return 0;
+ if (speed >= XFER_MW_DMA_0)
+ pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+ else
+ pio = 2; /* only SWDMA2 is allowed */
- (void) piix_tune_chipset(drive, speed);
- return ide_dma_enable(drive);
-}
-
-/**
- * piix_config_drive_xfer_rate - set up an IDE device
- * @drive: IDE drive to configure
- *
- * Set up the PIIX interface for the best available speed on this
- * interface, preferring DMA to PIO.
- */
-
-static int piix_config_drive_xfer_rate (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct hd_driveid *id = drive->id;
-
- drive->init_speed = 0;
-
- if ((id->capability & 1) && drive->autodma) {
-
- if (ide_use_dma(drive) && piix_config_drive_for_dma(drive))
- return hwif->ide_dma_on(drive);
-
- goto fast_ata_pio;
-
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
- /* Find best PIO mode. */
- (void) hwif->speedproc(drive, XFER_PIO_0 +
- ide_get_best_pio_mode(drive, 255, 4, NULL));
- return hwif->ide_dma_off_quietly(drive);
- }
- /* IORDY not supported */
- return 0;
-}
-
-/**
- * piix_is_ichx - check if ICHx
- * @dev: PCI device to check
- *
- * returns 1 if ICHx, 0 otherwise.
- */
-static int piix_is_ichx(struct pci_dev *dev)
-{
- switch (dev->device) {
- case PCI_DEVICE_ID_INTEL_82801EB_1:
- case PCI_DEVICE_ID_INTEL_82801AA_1:
- case PCI_DEVICE_ID_INTEL_82801AB_1:
- case PCI_DEVICE_ID_INTEL_82801BA_8:
- case PCI_DEVICE_ID_INTEL_82801BA_9:
- case PCI_DEVICE_ID_INTEL_82801CA_10:
- case PCI_DEVICE_ID_INTEL_82801CA_11:
- case PCI_DEVICE_ID_INTEL_82801DB_1:
- case PCI_DEVICE_ID_INTEL_82801DB_10:
- case PCI_DEVICE_ID_INTEL_82801DB_11:
- case PCI_DEVICE_ID_INTEL_82801EB_11:
- case PCI_DEVICE_ID_INTEL_82801E_11:
- case PCI_DEVICE_ID_INTEL_ESB_2:
- case PCI_DEVICE_ID_INTEL_ICH6_19:
- case PCI_DEVICE_ID_INTEL_ICH7_21:
- case PCI_DEVICE_ID_INTEL_ESB2_18:
- case PCI_DEVICE_ID_INTEL_ICH8_6:
- return 1;
+ piix_set_pio_mode(drive, pio);
}
-
- return 0;
}
/**
- * init_chipset_piix - set up the PIIX chipset
+ * init_chipset_ich - set up the ICH chipset
* @dev: PCI device to set up
* @name: Name of the device
*
- * Initialize the PCI device as required. For the PIIX this turns
- * out to be nice and simple
+ * Initialize the PCI device as required. For the ICH this turns
+ * out to be nice and simple.
*/
-static unsigned int __devinit init_chipset_piix (struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_ich(struct pci_dev *dev, const char *name)
{
- if (piix_is_ichx(dev)) {
- unsigned int extra = 0;
- pci_read_config_dword(dev, 0x54, &extra);
- pci_write_config_dword(dev, 0x54, extra|0x400);
- }
+ u32 extra = 0;
+
+ pci_read_config_dword(dev, 0x54, &extra);
+ pci_write_config_dword(dev, 0x54, extra | 0x400);
return 0;
}
u8 dma_stat;
/* clear the INTR & ERROR bits */
- dma_stat = hwif->INB(hwif->dma_status);
+ dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
/* Should we force the bit as well ? */
- hwif->OUTB(dma_stat, hwif->dma_status);
+ outb(dma_stat, hwif->dma_base + ATA_DMA_STATUS);
}
-static int __devinit piix_cable_detect(ide_hwif_t *hwif)
+struct ich_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+/*
+ * List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x27DF, 0x1025, 0x0102 }, /* ICH7 on Acer 5602aWLMi */
+ { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
+ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */
+ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on Acer Aspire 2023WLMi */
+ { 0x2653, 0x1043, 0x82D8 }, /* ICH6M on Asus Eee 701 */
+ /* end marker */
+ { 0, }
+};
+
+static u8 __devinit piix_cable_detect(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *pdev = to_pci_dev(hwif->dev);
+ const struct ich_laptop *lap = &ich_laptop[0];
u8 reg54h = 0, mask = hwif->channel ? 0xc0 : 0x30;
- pci_read_config_byte(dev, 0x54, ®54h);
+ /* check for specials */
+ while (lap->device) {
+ if (lap->device == pdev->device &&
+ lap->subvendor == pdev->subsystem_vendor &&
+ lap->subdevice == pdev->subsystem_device) {
+ return ATA_CBL_PATA40_SHORT;
+ }
+ lap++;
+ }
+
+ pci_read_config_byte(pdev, 0x54, ®54h);
- return (reg54h & mask) ? 1 : 0;
+ return (reg54h & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}
/**
static void __devinit init_hwif_piix(ide_hwif_t *hwif)
{
-#ifndef CONFIG_IA64
- if (!hwif->irq)
- hwif->irq = hwif->channel ? 15 : 14;
-#endif /* CONFIG_IA64 */
-
- if (hwif->pci_dev->device == PCI_DEVICE_ID_INTEL_82371MX) {
- /* This is a painful system best to let it self tune for now */
- return;
- }
-
- hwif->autodma = 0;
- hwif->tuneproc = &piix_tune_drive;
- hwif->speedproc = &piix_tune_chipset;
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
-
if (!hwif->dma_base)
return;
- /* ICHx need to clear the bmdma status for all interrupts */
- if (piix_is_ichx(hwif->pci_dev))
- hwif->ide_dma_clear_irq = &piix_dma_clear_irq;
-
- hwif->atapi_dma = 1;
- hwif->ultra_mask = 0x3f;
- hwif->mwdma_mask = 0x06;
- hwif->swdma_mask = 0x04;
-
- switch(hwif->pci_dev->device) {
- case PCI_DEVICE_ID_INTEL_82371FB_0:
- case PCI_DEVICE_ID_INTEL_82371FB_1:
- case PCI_DEVICE_ID_INTEL_82371SB_1:
- hwif->ultra_mask = 0x80;
- break;
- case PCI_DEVICE_ID_INTEL_82371AB:
- case PCI_DEVICE_ID_INTEL_82443MX_1:
- case PCI_DEVICE_ID_INTEL_82451NX:
- case PCI_DEVICE_ID_INTEL_82801AB_1:
- hwif->ultra_mask = 0x07;
- break;
- default:
- if (!hwif->udma_four)
- hwif->udma_four = piix_cable_detect(hwif);
- break;
- }
-
if (no_piix_dma)
hwif->ultra_mask = hwif->mwdma_mask = hwif->swdma_mask = 0;
+}
- hwif->ide_dma_check = &piix_config_drive_xfer_rate;
- if (!noautodma)
- hwif->autodma = 1;
+static void __devinit init_hwif_ich(ide_hwif_t *hwif)
+{
+ init_hwif_piix(hwif);
- hwif->drives[1].autodma = hwif->autodma;
- hwif->drives[0].autodma = hwif->autodma;
+ /* ICHx need to clear the BMDMA status for all interrupts */
+ if (hwif->dma_base)
+ hwif->ide_dma_clear_irq = &piix_dma_clear_irq;
}
-#define DECLARE_PIIX_DEV(name_str) \
+static const struct ide_port_ops piix_port_ops = {
+ .set_pio_mode = piix_set_pio_mode,
+ .set_dma_mode = piix_set_dma_mode,
+ .cable_detect = piix_cable_detect,
+};
+
+#ifndef CONFIG_IA64
+ #define IDE_HFLAGS_PIIX IDE_HFLAG_LEGACY_IRQS
+#else
+ #define IDE_HFLAGS_PIIX 0
+#endif
+
+#define DECLARE_PIIX_DEV(name_str, udma) \
{ \
.name = name_str, \
- .init_chipset = init_chipset_piix, \
.init_hwif = init_hwif_piix, \
- .channels = 2, \
- .autodma = AUTODMA, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
- .bootable = ON_BOARD, \
+ .port_ops = &piix_port_ops, \
+ .host_flags = IDE_HFLAGS_PIIX, \
+ .pio_mask = ATA_PIO4, \
+ .swdma_mask = ATA_SWDMA2_ONLY, \
+ .mwdma_mask = ATA_MWDMA12_ONLY, \
+ .udma_mask = udma, \
+ }
+
+#define DECLARE_ICH_DEV(name_str, udma) \
+ { \
+ .name = name_str, \
+ .init_chipset = init_chipset_ich, \
+ .init_hwif = init_hwif_ich, \
+ .enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
+ .port_ops = &piix_port_ops, \
+ .host_flags = IDE_HFLAGS_PIIX, \
+ .pio_mask = ATA_PIO4, \
+ .swdma_mask = ATA_SWDMA2_ONLY, \
+ .mwdma_mask = ATA_MWDMA12_ONLY, \
+ .udma_mask = udma, \
}
-static ide_pci_device_t piix_pci_info[] __devinitdata = {
- /* 0 */ DECLARE_PIIX_DEV("PIIXa"),
- /* 1 */ DECLARE_PIIX_DEV("PIIXb"),
+static const struct ide_port_info piix_pci_info[] __devinitdata = {
+ /* 0 */ DECLARE_PIIX_DEV("PIIXa", 0x00), /* no udma */
+ /* 1 */ DECLARE_PIIX_DEV("PIIXb", 0x00), /* no udma */
/* 2 */
{ /*
* of the bit 14 of the IDETIM register at offset 0x6c
*/
.name = "MPIIX",
- .init_hwif = init_hwif_piix,
- .channels = 2,
- .autodma = NODMA,
.enablebits = {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
- .bootable = ON_BOARD,
- .flags = IDEPCI_FLAG_ISA_PORTS
+ .host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA |
+ IDE_HFLAGS_PIIX,
+ .pio_mask = ATA_PIO4,
+ /* This is a painful system best to let it self tune for now */
},
- /* 3 */ DECLARE_PIIX_DEV("PIIX3"),
- /* 4 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 5 */ DECLARE_PIIX_DEV("ICH0"),
- /* 6 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 7 */ DECLARE_PIIX_DEV("ICH"),
- /* 8 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 9 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 10 */ DECLARE_PIIX_DEV("ICH2"),
- /* 11 */ DECLARE_PIIX_DEV("ICH2M"),
- /* 12 */ DECLARE_PIIX_DEV("ICH3M"),
- /* 13 */ DECLARE_PIIX_DEV("ICH3"),
- /* 14 */ DECLARE_PIIX_DEV("ICH4"),
- /* 15 */ DECLARE_PIIX_DEV("ICH5"),
- /* 16 */ DECLARE_PIIX_DEV("C-ICH"),
- /* 17 */ DECLARE_PIIX_DEV("ICH4"),
- /* 18 */ DECLARE_PIIX_DEV("ICH5-SATA"),
- /* 19 */ DECLARE_PIIX_DEV("ICH5"),
- /* 20 */ DECLARE_PIIX_DEV("ICH6"),
- /* 21 */ DECLARE_PIIX_DEV("ICH7"),
- /* 22 */ DECLARE_PIIX_DEV("ICH4"),
- /* 23 */ DECLARE_PIIX_DEV("ESB2"),
- /* 24 */ DECLARE_PIIX_DEV("ICH8M"),
+ /* 3 */ DECLARE_PIIX_DEV("PIIX3", 0x00), /* no udma */
+ /* 4 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
+ /* 5 */ DECLARE_ICH_DEV("ICH0", ATA_UDMA2),
+ /* 6 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
+ /* 7 */ DECLARE_ICH_DEV("ICH", ATA_UDMA4),
+ /* 8 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA4),
+ /* 9 */ DECLARE_PIIX_DEV("PIIX4", ATA_UDMA2),
+ /* 10 */ DECLARE_ICH_DEV("ICH2", ATA_UDMA5),
+ /* 11 */ DECLARE_ICH_DEV("ICH2M", ATA_UDMA5),
+ /* 12 */ DECLARE_ICH_DEV("ICH3M", ATA_UDMA5),
+ /* 13 */ DECLARE_ICH_DEV("ICH3", ATA_UDMA5),
+ /* 14 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
+ /* 15 */ DECLARE_ICH_DEV("ICH5", ATA_UDMA5),
+ /* 16 */ DECLARE_ICH_DEV("C-ICH", ATA_UDMA5),
+ /* 17 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
+ /* 18 */ DECLARE_ICH_DEV("ICH5-SATA", ATA_UDMA5),
+ /* 19 */ DECLARE_ICH_DEV("ICH5", ATA_UDMA5),
+ /* 20 */ DECLARE_ICH_DEV("ICH6", ATA_UDMA5),
+ /* 21 */ DECLARE_ICH_DEV("ICH7", ATA_UDMA5),
+ /* 22 */ DECLARE_ICH_DEV("ICH4", ATA_UDMA5),
+ /* 23 */ DECLARE_ICH_DEV("ESB2", ATA_UDMA5),
+ /* 24 */ DECLARE_ICH_DEV("ICH8M", ATA_UDMA5),
};
/**
static int __devinit piix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_pci_device_t *d = &piix_pci_info[id->driver_data];
-
- return ide_setup_pci_device(dev, d);
+ return ide_setup_pci_device(dev, &piix_pci_info[id->driver_data]);
}
/**
{
struct pci_dev *pdev = NULL;
u16 cfg;
- u8 rev;
while((pdev=pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev))!=NULL)
{
/* Look for 450NX PXB. Check for problem configurations
A PCI quirk checks bit 6 already */
- pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
pci_read_config_word(pdev, 0x41, &cfg);
/* Only on the original revision: IDE DMA can hang */
- if(rev == 0x00)
+ if (pdev->revision == 0x00)
no_piix_dma = 1;
/* On all revisions below 5 PXB bus lock must be disabled for IDE */
- else if(cfg & (1<<14) && rev < 5)
+ else if (cfg & (1<<14) && pdev->revision < 5)
no_piix_dma = 2;
}
if(no_piix_dma)
printk(KERN_WARNING "piix: A BIOS update may resolve this.\n");
}
-static struct pci_device_id piix_pci_tbl[] = {
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82372FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801E_11, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17},
+static const struct pci_device_id piix_pci_tbl[] = {
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0), 0 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1), 1 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), 2 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1), 3 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB), 4 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1), 5 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1), 6 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1), 7 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1), 8 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX), 9 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9), 10 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8), 11 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 12 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 13 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 14 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 15 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11), 16 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 17 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 18},
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1), 18 },
#endif
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 19},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_19, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 20},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 21},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 22},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_18, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 23},
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 24},
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2), 19 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19), 20 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21), 21 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1), 22 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18), 23 },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6), 24 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff