* Split from:
* linux/drivers/ide/pdc202xx.c Version 0.35 Mar. 30, 2002
* Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2005-2007 MontaVista Software, Inc.
* Portions Copyright (C) 1999 Promise Technology, Inc.
* Author: Frank Tiernan (frankt@promise.com)
* Released under terms of General Public License
*/
-#include <linux/config.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
#include <linux/hdreg.h>
-#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/ide.h>
#include <asm/io.h>
-#include <asm/irq.h>
#ifdef CONFIG_PPC_PMAC
#include <asm/prom.h>
#include <asm/pci-bridge.h>
#endif
-#define PDC202_DEBUG_CABLE 0
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(fmt, args...) printk("%s: " fmt, __func__, ## args)
+#else
+#define DBG(fmt, args...)
+#endif
static const char *pdc_quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
NULL
};
-#define set_2regs(a, b) \
- do { \
- hwif->OUTB((a + adj), indexreg); \
- hwif->OUTB(b, datareg); \
- } while(0)
-
-#define set_ultra(a, b, c) \
- do { \
- set_2regs(0x10,(a)); \
- set_2regs(0x11,(b)); \
- set_2regs(0x12,(c)); \
- } while(0)
-
-#define set_ata2(a, b) \
- do { \
- set_2regs(0x0e,(a)); \
- set_2regs(0x0f,(b)); \
- } while(0)
-
-#define set_pio(a, b, c) \
- do { \
- set_2regs(0x0c,(a)); \
- set_2regs(0x0d,(b)); \
- set_2regs(0x13,(c)); \
- } while(0)
-
-static u8 pdcnew_ratemask (ide_drive_t *drive)
+static u8 max_dma_rate(struct pci_dev *pdev)
{
u8 mode;
- switch(HWIF(drive)->pci_dev->device) {
+ switch(pdev->device) {
case PCI_DEVICE_ID_PROMISE_20277:
case PCI_DEVICE_ID_PROMISE_20276:
case PCI_DEVICE_ID_PROMISE_20275:
default:
return 0;
}
- if (!eighty_ninty_three(drive))
- mode = min(mode, (u8)1);
+
return mode;
}
-static int check_in_drive_lists (ide_drive_t *drive, const char **list)
+/**
+ * get_indexed_reg - Get indexed register
+ * @hwif: for the port address
+ * @index: index of the indexed register
+ */
+static u8 get_indexed_reg(ide_hwif_t *hwif, u8 index)
{
- struct hd_driveid *id = drive->id;
+ u8 value;
- if (pdc_quirk_drives == list) {
- while (*list) {
- if (strstr(id->model, *list++)) {
- return 2;
- }
- }
- } else {
- while (*list) {
- if (!strcmp(*list++,id->model)) {
- return 1;
- }
- }
- }
- return 0;
+ outb(index, hwif->dma_base + 1);
+ value = inb(hwif->dma_base + 3);
+
+ DBG("index[%02X] value[%02X]\n", index, value);
+ return value;
}
-static int pdcnew_new_tune_chipset (ide_drive_t *drive, u8 xferspeed)
+/**
+ * set_indexed_reg - Set indexed register
+ * @hwif: for the port address
+ * @index: index of the indexed register
+ */
+static void set_indexed_reg(ide_hwif_t *hwif, u8 index, u8 value)
{
- ide_hwif_t *hwif = HWIF(drive);
- unsigned long indexreg = hwif->dma_vendor1;
- unsigned long datareg = hwif->dma_vendor3;
- u8 thold = 0x10;
- u8 adj = (drive->dn%2) ? 0x08 : 0x00;
- u8 speed = ide_rate_filter(pdcnew_ratemask(drive), xferspeed);
-
- if (speed == XFER_UDMA_2) {
- hwif->OUTB((thold + adj), indexreg);
- hwif->OUTB((hwif->INB(datareg) & 0x7f), datareg);
- }
-
- switch (speed) {
- case XFER_UDMA_7:
- speed = XFER_UDMA_6;
- case XFER_UDMA_6: set_ultra(0x1a, 0x01, 0xcb); break;
- case XFER_UDMA_5: set_ultra(0x1a, 0x02, 0xcb); break;
- case XFER_UDMA_4: set_ultra(0x1a, 0x03, 0xcd); break;
- case XFER_UDMA_3: set_ultra(0x1a, 0x05, 0xcd); break;
- case XFER_UDMA_2: set_ultra(0x2a, 0x07, 0xcd); break;
- case XFER_UDMA_1: set_ultra(0x3a, 0x0a, 0xd0); break;
- case XFER_UDMA_0: set_ultra(0x4a, 0x0f, 0xd5); break;
- case XFER_MW_DMA_2: set_ata2(0x69, 0x25); break;
- case XFER_MW_DMA_1: set_ata2(0x6b, 0x27); break;
- case XFER_MW_DMA_0: set_ata2(0xdf, 0x5f); break;
- case XFER_PIO_4: set_pio(0x23, 0x09, 0x25); break;
- case XFER_PIO_3: set_pio(0x27, 0x0d, 0x35); break;
- case XFER_PIO_2: set_pio(0x23, 0x26, 0x64); break;
- case XFER_PIO_1: set_pio(0x46, 0x29, 0xa4); break;
- case XFER_PIO_0: set_pio(0xfb, 0x2b, 0xac); break;
- default:
- ;
- }
-
- return (ide_config_drive_speed(drive, speed));
+ outb(index, hwif->dma_base + 1);
+ outb(value, hwif->dma_base + 3);
+ DBG("index[%02X] value[%02X]\n", index, value);
}
-/* 0 1 2 3 4 5 6 7 8
- * 960, 480, 390, 300, 240, 180, 120, 90, 60
- * 180, 150, 120, 90, 60
- * DMA_Speed
- * 180, 120, 90, 90, 90, 60, 30
- * 11, 5, 4, 3, 2, 1, 0
+/*
+ * ATA Timing Tables based on 133 MHz PLL output clock.
+ *
+ * If the PLL outputs 100 MHz clock, the ASIC hardware will set
+ * the timing registers automatically when "set features" command is
+ * issued to the device. However, if the PLL output clock is 133 MHz,
+ * the following tables must be used.
*/
-static void pdcnew_tune_drive(ide_drive_t *drive, u8 pio)
-{
- u8 speed;
+static struct pio_timing {
+ u8 reg0c, reg0d, reg13;
+} pio_timings [] = {
+ { 0xfb, 0x2b, 0xac }, /* PIO mode 0, IORDY off, Prefetch off */
+ { 0x46, 0x29, 0xa4 }, /* PIO mode 1, IORDY off, Prefetch off */
+ { 0x23, 0x26, 0x64 }, /* PIO mode 2, IORDY off, Prefetch off */
+ { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */
+ { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */
+};
- if (pio == 5) pio = 4;
- speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, pio, NULL);
+static struct mwdma_timing {
+ u8 reg0e, reg0f;
+} mwdma_timings [] = {
+ { 0xdf, 0x5f }, /* MWDMA mode 0 */
+ { 0x6b, 0x27 }, /* MWDMA mode 1 */
+ { 0x69, 0x25 }, /* MWDMA mode 2 */
+};
- (void)pdcnew_new_tune_chipset(drive, speed);
-}
+static struct udma_timing {
+ u8 reg10, reg11, reg12;
+} udma_timings [] = {
+ { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
+ { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
+ { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */
+ { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */
+ { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */
+ { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */
+ { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
+};
-static u8 pdcnew_new_cable_detect (ide_hwif_t *hwif)
+static void pdcnew_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
- hwif->OUTB(0x0b, hwif->dma_vendor1);
- return ((u8)((hwif->INB(hwif->dma_vendor3) & 0x04)));
-}
-static int config_chipset_for_dma (ide_drive_t *drive)
-{
- struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
- u8 speed = -1;
- u8 cable;
-
- u8 ultra_66 = ((id->dma_ultra & 0x0010) ||
- (id->dma_ultra & 0x0008)) ? 1 : 0;
-
- cable = pdcnew_new_cable_detect(hwif);
-
- if (ultra_66 && cable) {
- printk(KERN_WARNING "Warning: %s channel requires an 80-pin cable for operation.\n", hwif->channel ? "Secondary":"Primary");
- printk(KERN_WARNING "%s reduced to Ultra33 mode.\n", drive->name);
- }
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
- if (drive->media != ide_disk)
- return 0;
- if (id->capability & 4) { /* IORDY_EN & PREFETCH_EN */
- hwif->OUTB((0x13 + ((drive->dn%2) ? 0x08 : 0x00)), hwif->dma_vendor1);
- hwif->OUTB((hwif->INB(hwif->dma_vendor3)|0x03), hwif->dma_vendor3);
- }
+ /*
+ * IDE core issues SETFEATURES_XFER to the drive first (thanks to
+ * IDE_HFLAG_POST_SET_MODE in ->host_flags). PDC202xx hardware will
+ * automatically set the timing registers based on 100 MHz PLL output.
+ *
+ * As we set up the PLL to output 133 MHz for UltraDMA/133 capable
+ * chips, we must override the default register settings...
+ */
+ if (max_dma_rate(dev) == 4) {
+ u8 mode = speed & 0x07;
+
+ if (speed >= XFER_UDMA_0) {
+ set_indexed_reg(hwif, 0x10 + adj,
+ udma_timings[mode].reg10);
+ set_indexed_reg(hwif, 0x11 + adj,
+ udma_timings[mode].reg11);
+ set_indexed_reg(hwif, 0x12 + adj,
+ udma_timings[mode].reg12);
+ } else {
+ set_indexed_reg(hwif, 0x0e + adj,
+ mwdma_timings[mode].reg0e);
+ set_indexed_reg(hwif, 0x0f + adj,
+ mwdma_timings[mode].reg0f);
+ }
+ } else if (speed == XFER_UDMA_2) {
+ /* Set tHOLD bit to 0 if using UDMA mode 2 */
+ u8 tmp = get_indexed_reg(hwif, 0x10 + adj);
- speed = ide_dma_speed(drive, pdcnew_ratemask(drive));
+ set_indexed_reg(hwif, 0x10 + adj, tmp & 0x7f);
+ }
+}
- if (!(speed)) {
- hwif->tuneproc(drive, 5);
- return 0;
+static void pdcnew_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
+
+ if (max_dma_rate(dev) == 4) {
+ set_indexed_reg(hwif, 0x0c + adj, pio_timings[pio].reg0c);
+ set_indexed_reg(hwif, 0x0d + adj, pio_timings[pio].reg0d);
+ set_indexed_reg(hwif, 0x13 + adj, pio_timings[pio].reg13);
}
-
- (void) hwif->speedproc(drive, speed);
- return ide_dma_enable(drive);
}
-static int pdcnew_config_drive_xfer_rate (ide_drive_t *drive)
+static u8 __devinit pdcnew_cable_detect(ide_hwif_t *hwif)
{
- ide_hwif_t *hwif = HWIF(drive);
- struct hd_driveid *id = drive->id;
-
- drive->init_speed = 0;
+ if (get_indexed_reg(hwif, 0x0b) & 0x04)
+ return ATA_CBL_PATA40;
+ else
+ return ATA_CBL_PATA80;
+}
- if (id && (id->capability & 1) && drive->autodma) {
+static void pdcnew_quirkproc(ide_drive_t *drive)
+{
+ const char **list, *model = drive->id->model;
- if (ide_use_dma(drive)) {
- if (config_chipset_for_dma(drive))
- return hwif->ide_dma_on(drive);
+ for (list = pdc_quirk_drives; *list != NULL; list++)
+ if (strstr(model, *list) != NULL) {
+ drive->quirk_list = 2;
+ return;
}
- goto fast_ata_pio;
-
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
- hwif->tuneproc(drive, 5);
- return hwif->ide_dma_off_quietly(drive);
- }
- /* IORDY not supported */
- return 0;
+ drive->quirk_list = 0;
}
-static int pdcnew_quirkproc (ide_drive_t *drive)
+static void pdcnew_reset(ide_drive_t *drive)
{
- return ((int) check_in_drive_lists(drive, pdc_quirk_drives));
+ /*
+ * Deleted this because it is redundant from the caller.
+ */
+ printk(KERN_WARNING "pdc202xx_new: %s channel reset.\n",
+ HWIF(drive)->channel ? "Secondary" : "Primary");
}
-static int pdcnew_ide_dma_lostirq(ide_drive_t *drive)
+/**
+ * read_counter - Read the byte count registers
+ * @dma_base: for the port address
+ */
+static long __devinit read_counter(u32 dma_base)
{
- if (HWIF(drive)->resetproc != NULL)
- HWIF(drive)->resetproc(drive);
- return __ide_dma_lostirq(drive);
+ u32 pri_dma_base = dma_base, sec_dma_base = dma_base + 0x08;
+ u8 cnt0, cnt1, cnt2, cnt3;
+ long count = 0, last;
+ int retry = 3;
+
+ do {
+ last = count;
+
+ /* Read the current count */
+ outb(0x20, pri_dma_base + 0x01);
+ cnt0 = inb(pri_dma_base + 0x03);
+ outb(0x21, pri_dma_base + 0x01);
+ cnt1 = inb(pri_dma_base + 0x03);
+ outb(0x20, sec_dma_base + 0x01);
+ cnt2 = inb(sec_dma_base + 0x03);
+ outb(0x21, sec_dma_base + 0x01);
+ cnt3 = inb(sec_dma_base + 0x03);
+
+ count = (cnt3 << 23) | (cnt2 << 15) | (cnt1 << 8) | cnt0;
+
+ /*
+ * The 30-bit decrementing counter is read in 4 pieces.
+ * Incorrect value may be read when the most significant bytes
+ * are changing...
+ */
+ } while (retry-- && (((last ^ count) & 0x3fff8000) || last < count));
+
+ DBG("cnt0[%02X] cnt1[%02X] cnt2[%02X] cnt3[%02X]\n",
+ cnt0, cnt1, cnt2, cnt3);
+
+ return count;
}
-static int pdcnew_ide_dma_timeout(ide_drive_t *drive)
+/**
+ * detect_pll_input_clock - Detect the PLL input clock in Hz.
+ * @dma_base: for the port address
+ * E.g. 16949000 on 33 MHz PCI bus, i.e. half of the PCI clock.
+ */
+static long __devinit detect_pll_input_clock(unsigned long dma_base)
{
- if (HWIF(drive)->resetproc != NULL)
- HWIF(drive)->resetproc(drive);
- return __ide_dma_timeout(drive);
-}
+ struct timeval start_time, end_time;
+ long start_count, end_count;
+ long pll_input, usec_elapsed;
+ u8 scr1;
+
+ start_count = read_counter(dma_base);
+ do_gettimeofday(&start_time);
+
+ /* Start the test mode */
+ outb(0x01, dma_base + 0x01);
+ scr1 = inb(dma_base + 0x03);
+ DBG("scr1[%02X]\n", scr1);
+ outb(scr1 | 0x40, dma_base + 0x03);
+
+ /* Let the counter run for 10 ms. */
+ mdelay(10);
+
+ end_count = read_counter(dma_base);
+ do_gettimeofday(&end_time);
+
+ /* Stop the test mode */
+ outb(0x01, dma_base + 0x01);
+ scr1 = inb(dma_base + 0x03);
+ DBG("scr1[%02X]\n", scr1);
+ outb(scr1 & ~0x40, dma_base + 0x03);
-static void pdcnew_new_reset (ide_drive_t *drive)
-{
/*
- * Deleted this because it is redundant from the caller.
+ * Calculate the input clock in Hz
+ * (the clock counter is 30 bit wide and counts down)
*/
- printk(KERN_WARNING "PDC202XX: %s channel reset.\n",
- HWIF(drive)->channel ? "Secondary" : "Primary");
+ usec_elapsed = (end_time.tv_sec - start_time.tv_sec) * 1000000 +
+ (end_time.tv_usec - start_time.tv_usec);
+ pll_input = ((start_count - end_count) & 0x3fffffff) / 10 *
+ (10000000 / usec_elapsed);
+
+ DBG("start[%ld] end[%ld]\n", start_count, end_count);
+
+ return pll_input;
}
#ifdef CONFIG_PPC_PMAC
static void __devinit apple_kiwi_init(struct pci_dev *pdev)
{
struct device_node *np = pci_device_to_OF_node(pdev);
- unsigned int class_rev = 0;
- void __iomem *mmio;
u8 conf;
- if (np == NULL || !device_is_compatible(np, "kiwi-root"))
+ if (np == NULL || !of_device_is_compatible(np, "kiwi-root"))
return;
- pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
-
- if (class_rev >= 0x03) {
+ if (pdev->revision >= 0x03) {
/* Setup chip magic config stuff (from darwin) */
- pci_read_config_byte(pdev, 0x40, &conf);
- pci_write_config_byte(pdev, 0x40, conf | 0x01);
- }
- mmio = ioremap(pci_resource_start(pdev, 5),
- pci_resource_len(pdev, 5));
-
- /* Setup some PLL stuffs */
- switch (pdev->device) {
- case PCI_DEVICE_ID_PROMISE_20270:
- writew(0x0d2b, mmio + 0x1202);
- mdelay(30);
- break;
- case PCI_DEVICE_ID_PROMISE_20271:
- writew(0x0826, mmio + 0x1202);
- mdelay(30);
- break;
+ pci_read_config_byte (pdev, 0x40, &conf);
+ pci_write_config_byte(pdev, 0x40, (conf | 0x01));
}
-
- iounmap(mmio);
}
#endif /* CONFIG_PPC_PMAC */
static unsigned int __devinit init_chipset_pdcnew(struct pci_dev *dev, const char *name)
{
- if (dev->resource[PCI_ROM_RESOURCE].start) {
- pci_write_config_dword(dev, PCI_ROM_ADDRESS,
- dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
- printk(KERN_INFO "%s: ROM enabled at 0x%08lx\n",
- name, dev->resource[PCI_ROM_RESOURCE].start);
- }
+ unsigned long dma_base = pci_resource_start(dev, 4);
+ unsigned long sec_dma_base = dma_base + 0x08;
+ long pll_input, pll_output, ratio;
+ int f, r;
+ u8 pll_ctl0, pll_ctl1;
+
+ if (dma_base == 0)
+ return -EFAULT;
#ifdef CONFIG_PPC_PMAC
apple_kiwi_init(dev);
#endif
+ /* Calculate the required PLL output frequency */
+ switch(max_dma_rate(dev)) {
+ case 4: /* it's 133 MHz for Ultra133 chips */
+ pll_output = 133333333;
+ break;
+ case 3: /* and 100 MHz for Ultra100 chips */
+ default:
+ pll_output = 100000000;
+ break;
+ }
+
+ /*
+ * Detect PLL input clock.
+ * On some systems, where PCI bus is running at non-standard clock rate
+ * (e.g. 25 or 40 MHz), we have to adjust the cycle time.
+ * PDC20268 and newer chips employ PLL circuit to help correct timing
+ * registers setting.
+ */
+ pll_input = detect_pll_input_clock(dma_base);
+ printk(KERN_INFO "%s %s: PLL input clock is %ld kHz\n",
+ name, pci_name(dev), pll_input / 1000);
+
+ /* Sanity check */
+ if (unlikely(pll_input < 5000000L || pll_input > 70000000L)) {
+ printk(KERN_ERR "%s %s: Bad PLL input clock %ld Hz, giving up!"
+ "\n", name, pci_name(dev), pll_input);
+ goto out;
+ }
+
+#ifdef DEBUG
+ DBG("pll_output is %ld Hz\n", pll_output);
+
+ /* Show the current clock value of PLL control register
+ * (maybe already configured by the BIOS)
+ */
+ outb(0x02, sec_dma_base + 0x01);
+ pll_ctl0 = inb(sec_dma_base + 0x03);
+ outb(0x03, sec_dma_base + 0x01);
+ pll_ctl1 = inb(sec_dma_base + 0x03);
+
+ DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
+#endif
+
+ /*
+ * Calculate the ratio of F, R and NO
+ * POUT = (F + 2) / (( R + 2) * NO)
+ */
+ ratio = pll_output / (pll_input / 1000);
+ if (ratio < 8600L) { /* 8.6x */
+ /* Using NO = 0x01, R = 0x0d */
+ r = 0x0d;
+ } else if (ratio < 12900L) { /* 12.9x */
+ /* Using NO = 0x01, R = 0x08 */
+ r = 0x08;
+ } else if (ratio < 16100L) { /* 16.1x */
+ /* Using NO = 0x01, R = 0x06 */
+ r = 0x06;
+ } else if (ratio < 64000L) { /* 64x */
+ r = 0x00;
+ } else {
+ /* Invalid ratio */
+ printk(KERN_ERR "%s %s: Bad ratio %ld, giving up!\n",
+ name, pci_name(dev), ratio);
+ goto out;
+ }
+
+ f = (ratio * (r + 2)) / 1000 - 2;
+
+ DBG("F[%d] R[%d] ratio*1000[%ld]\n", f, r, ratio);
+
+ if (unlikely(f < 0 || f > 127)) {
+ /* Invalid F */
+ printk(KERN_ERR "%s %s: F[%d] invalid!\n",
+ name, pci_name(dev), f);
+ goto out;
+ }
+
+ pll_ctl0 = (u8) f;
+ pll_ctl1 = (u8) r;
+
+ DBG("Writing pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
+
+ outb(0x02, sec_dma_base + 0x01);
+ outb(pll_ctl0, sec_dma_base + 0x03);
+ outb(0x03, sec_dma_base + 0x01);
+ outb(pll_ctl1, sec_dma_base + 0x03);
+
+ /* Wait the PLL circuit to be stable */
+ mdelay(30);
+
+#ifdef DEBUG
+ /*
+ * Show the current clock value of PLL control register
+ */
+ outb(0x02, sec_dma_base + 0x01);
+ pll_ctl0 = inb(sec_dma_base + 0x03);
+ outb(0x03, sec_dma_base + 0x01);
+ pll_ctl1 = inb(sec_dma_base + 0x03);
+
+ DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
+#endif
+
+ out:
return dev->irq;
}
-static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif)
+static struct pci_dev * __devinit pdc20270_get_dev2(struct pci_dev *dev)
{
- hwif->autodma = 0;
-
- hwif->tuneproc = &pdcnew_tune_drive;
- hwif->quirkproc = &pdcnew_quirkproc;
- hwif->speedproc = &pdcnew_new_tune_chipset;
- hwif->resetproc = &pdcnew_new_reset;
-
- hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
-
- hwif->ultra_mask = 0x7f;
- hwif->mwdma_mask = 0x07;
-
- hwif->ide_dma_check = &pdcnew_config_drive_xfer_rate;
- hwif->ide_dma_lostirq = &pdcnew_ide_dma_lostirq;
- hwif->ide_dma_timeout = &pdcnew_ide_dma_timeout;
- if (!(hwif->udma_four))
- hwif->udma_four = (pdcnew_new_cable_detect(hwif)) ? 0 : 1;
- if (!noautodma)
- hwif->autodma = 1;
- hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
-#if PDC202_DEBUG_CABLE
- printk(KERN_DEBUG "%s: %s-pin cable\n",
- hwif->name, hwif->udma_four ? "80" : "40");
-#endif /* PDC202_DEBUG_CABLE */
-}
+ struct pci_dev *dev2;
-static int __devinit init_setup_pdcnew(struct pci_dev *dev, ide_pci_device_t *d)
-{
- return ide_setup_pci_device(dev, d);
-}
+ dev2 = pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn) + 1,
+ PCI_FUNC(dev->devfn)));
-static int __devinit init_setup_pdc20270(struct pci_dev *dev,
- ide_pci_device_t *d)
-{
- struct pci_dev *findev = NULL;
+ if (dev2 &&
+ dev2->vendor == dev->vendor &&
+ dev2->device == dev->device) {
- if ((dev->bus->self &&
- dev->bus->self->vendor == PCI_VENDOR_ID_DEC) &&
- (dev->bus->self->device == PCI_DEVICE_ID_DEC_21150)) {
- if (PCI_SLOT(dev->devfn) & 2)
- return -ENODEV;
- d->extra = 0;
- while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) {
- if ((findev->vendor == dev->vendor) &&
- (findev->device == dev->device) &&
- (PCI_SLOT(findev->devfn) & 2)) {
- if (findev->irq != dev->irq) {
- findev->irq = dev->irq;
- }
- return ide_setup_pci_devices(dev, findev, d);
- }
+ if (dev2->irq != dev->irq) {
+ dev2->irq = dev->irq;
+ printk(KERN_INFO "PDC20270 %s: PCI config space "
+ "interrupt fixed\n", pci_name(dev));
}
- }
- return ide_setup_pci_device(dev, d);
-}
-static int __devinit init_setup_pdc20276(struct pci_dev *dev,
- ide_pci_device_t *d)
-{
- if ((dev->bus->self) &&
- (dev->bus->self->vendor == PCI_VENDOR_ID_INTEL) &&
- ((dev->bus->self->device == PCI_DEVICE_ID_INTEL_I960) ||
- (dev->bus->self->device == PCI_DEVICE_ID_INTEL_I960RM))) {
- printk(KERN_INFO "ide: Skipping Promise PDC20276 "
- "attached to I2O RAID controller.\n");
- return -ENODEV;
+ return dev2;
}
- return ide_setup_pci_device(dev, d);
+
+ return NULL;
}
-static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "PDC20268",
- .init_setup = init_setup_pdcnew,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 1 */
- .name = "PDC20269",
- .init_setup = init_setup_pdcnew,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 2 */
- .name = "PDC20270",
- .init_setup = init_setup_pdc20270,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 3 */
- .name = "PDC20271",
- .init_setup = init_setup_pdcnew,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 4 */
- .name = "PDC20275",
- .init_setup = init_setup_pdcnew,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 5 */
- .name = "PDC20276",
- .init_setup = init_setup_pdc20276,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
- },{ /* 6 */
- .name = "PDC20277",
- .init_setup = init_setup_pdcnew,
- .init_chipset = init_chipset_pdcnew,
- .init_hwif = init_hwif_pdc202new,
- .channels = 2,
- .autodma = AUTODMA,
- .bootable = OFF_BOARD,
+static const struct ide_port_ops pdcnew_port_ops = {
+ .set_pio_mode = pdcnew_set_pio_mode,
+ .set_dma_mode = pdcnew_set_dma_mode,
+ .quirkproc = pdcnew_quirkproc,
+ .resetproc = pdcnew_reset,
+ .cable_detect = pdcnew_cable_detect,
+};
+
+#define DECLARE_PDCNEW_DEV(name_str, udma) \
+ { \
+ .name = name_str, \
+ .init_chipset = init_chipset_pdcnew, \
+ .port_ops = &pdcnew_port_ops, \
+ .host_flags = IDE_HFLAG_POST_SET_MODE | \
+ IDE_HFLAG_ERROR_STOPS_FIFO | \
+ IDE_HFLAG_OFF_BOARD, \
+ .pio_mask = ATA_PIO4, \
+ .mwdma_mask = ATA_MWDMA2, \
+ .udma_mask = udma, \
}
+
+static const struct ide_port_info pdcnew_chipsets[] __devinitdata = {
+ /* 0 */ DECLARE_PDCNEW_DEV("PDC20268", ATA_UDMA5),
+ /* 1 */ DECLARE_PDCNEW_DEV("PDC20269", ATA_UDMA6),
+ /* 2 */ DECLARE_PDCNEW_DEV("PDC20270", ATA_UDMA5),
+ /* 3 */ DECLARE_PDCNEW_DEV("PDC20271", ATA_UDMA6),
+ /* 4 */ DECLARE_PDCNEW_DEV("PDC20275", ATA_UDMA6),
+ /* 5 */ DECLARE_PDCNEW_DEV("PDC20276", ATA_UDMA6),
+ /* 6 */ DECLARE_PDCNEW_DEV("PDC20277", ATA_UDMA6),
};
/**
static int __devinit pdc202new_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_pci_device_t *d = &pdcnew_chipsets[id->driver_data];
+ const struct ide_port_info *d;
+ struct pci_dev *bridge = dev->bus->self;
+ u8 idx = id->driver_data;
+
+ d = &pdcnew_chipsets[idx];
- return d->init_setup(dev, d);
+ if (idx == 2 && bridge &&
+ bridge->vendor == PCI_VENDOR_ID_DEC &&
+ bridge->device == PCI_DEVICE_ID_DEC_21150) {
+ struct pci_dev *dev2;
+
+ if (PCI_SLOT(dev->devfn) & 2)
+ return -ENODEV;
+
+ dev2 = pdc20270_get_dev2(dev);
+
+ if (dev2) {
+ int ret = ide_pci_init_two(dev, dev2, d, NULL);
+ if (ret < 0)
+ pci_dev_put(dev2);
+ return ret;
+ }
+ }
+
+ if (idx == 5 && bridge &&
+ bridge->vendor == PCI_VENDOR_ID_INTEL &&
+ (bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
+ bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
+ printk(KERN_INFO "PDC20276 %s: attached to I2O RAID controller,"
+ " skipping\n", pci_name(dev));
+ return -ENODEV;
+ }
+
+ return ide_pci_init_one(dev, d, NULL);
+}
+
+static void __devexit pdc202new_remove(struct pci_dev *dev)
+{
+ struct ide_host *host = pci_get_drvdata(dev);
+ struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
+
+ ide_pci_remove(dev);
+ pci_dev_put(dev2);
}
-static struct pci_device_id pdc202new_pci_tbl[] = {
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
- { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
+static const struct pci_device_id pdc202new_pci_tbl[] = {
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 2 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 3 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 4 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 5 },
+ { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 6 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
.name = "Promise_IDE",
.id_table = pdc202new_pci_tbl,
.probe = pdc202new_init_one,
+ .remove = pdc202new_remove,
};
-static int pdc202new_ide_init(void)
+static int __init pdc202new_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
+static void __exit pdc202new_ide_exit(void)
+{
+ pci_unregister_driver(&driver);
+}
+
module_init(pdc202new_ide_init);
+module_exit(pdc202new_ide_exit);
MODULE_AUTHOR("Andre Hedrick, Frank Tiernan");
MODULE_DESCRIPTION("PCI driver module for Promise PDC20268 and higher");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff