/*
- * linux/drivers/ide/pci/alim15x3.c Version 0.26 Jul 14 2007
- *
* Copyright (C) 1998-2000 Michel Aubry, Maintainer
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
* Copyright (C) 1999-2000 CJ, cjtsai@ali.com.tw, Maintainer
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/pci.h>
-#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
-#define DISPLAY_ALI_TIMINGS
+/*
+ * Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
+ * (this is DANGEROUS and could result in data corruption).
+ */
+static int wdc_udma;
+
+module_param(wdc_udma, bool, 0);
+MODULE_PARM_DESC(wdc_udma,
+ "allow UDMA on M1543C-E chipset for WDC disks (DANGEROUS)");
/*
* ALi devices are not plug in. Otherwise these static values would
static u8 chip_is_1543c_e;
static struct pci_dev *isa_dev;
-#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
-#include <linux/stat.h>
-#include <linux/proc_fs.h>
-
-static u8 ali_proc = 0;
-
-static struct pci_dev *bmide_dev;
-
-static char *fifo[4] = {
- "FIFO Off",
- "FIFO On ",
- "DMA mode",
- "PIO mode" };
-
-static char *udmaT[8] = {
- "1.5T",
- " 2T",
- "2.5T",
- " 3T",
- "3.5T",
- " 4T",
- " 6T",
- " 8T"
-};
-
-static char *channel_status[8] = {
- "OK ",
- "busy ",
- "DRQ ",
- "DRQ busy ",
- "error ",
- "error busy ",
- "error DRQ ",
- "error DRQ busy"
-};
-
-/**
- * ali_get_info - generate proc file for ALi IDE
- * @buffer: buffer to fill
- * @addr: address of user start in buffer
- * @offset: offset into 'file'
- * @count: buffer count
- *
- * Walks the Ali devices and outputs summary data on the tuning and
- * anything else that will help with debugging
- */
-
-static int ali_get_info (char *buffer, char **addr, off_t offset, int count)
-{
- unsigned long bibma;
- u8 reg53h, reg5xh, reg5yh, reg5xh1, reg5yh1, c0, c1, rev, tmp;
- char *q, *p = buffer;
-
- /* fetch rev. */
- pci_read_config_byte(bmide_dev, 0x08, &rev);
- if (rev >= 0xc1) /* M1543C or newer */
- udmaT[7] = " ???";
- else
- fifo[3] = " ??? ";
-
- /* first fetch bibma: */
-
- bibma = pci_resource_start(bmide_dev, 4);
-
- /*
- * at that point bibma+0x2 et bibma+0xa are byte
- * registers to investigate:
- */
- c0 = inb(bibma + 0x02);
- c1 = inb(bibma + 0x0a);
-
- p += sprintf(p,
- "\n Ali M15x3 Chipset.\n");
- p += sprintf(p,
- " ------------------\n");
- pci_read_config_byte(bmide_dev, 0x78, ®53h);
- p += sprintf(p, "PCI Clock: %d.\n", reg53h);
-
- pci_read_config_byte(bmide_dev, 0x53, ®53h);
- p += sprintf(p,
- "CD_ROM FIFO:%s, CD_ROM DMA:%s\n",
- (reg53h & 0x02) ? "Yes" : "No ",
- (reg53h & 0x01) ? "Yes" : "No " );
- pci_read_config_byte(bmide_dev, 0x74, ®53h);
- p += sprintf(p,
- "FIFO Status: contains %d Words, runs%s%s\n\n",
- (reg53h & 0x3f),
- (reg53h & 0x40) ? " OVERWR" : "",
- (reg53h & 0x80) ? " OVERRD." : "." );
-
- p += sprintf(p,
- "-------------------primary channel"
- "-------------------secondary channel"
- "---------\n\n");
-
- pci_read_config_byte(bmide_dev, 0x09, ®53h);
- p += sprintf(p,
- "channel status: %s"
- " %s\n",
- (reg53h & 0x20) ? "On " : "Off",
- (reg53h & 0x10) ? "On " : "Off" );
-
- p += sprintf(p,
- "both channels togth: %s"
- " %s\n",
- (c0&0x80) ? "No " : "Yes",
- (c1&0x80) ? "No " : "Yes" );
-
- pci_read_config_byte(bmide_dev, 0x76, ®53h);
- p += sprintf(p,
- "Channel state: %s %s\n",
- channel_status[reg53h & 0x07],
- channel_status[(reg53h & 0x70) >> 4] );
-
- pci_read_config_byte(bmide_dev, 0x58, ®5xh);
- pci_read_config_byte(bmide_dev, 0x5c, ®5yh);
- p += sprintf(p,
- "Add. Setup Timing: %dT"
- " %dT\n",
- (reg5xh & 0x07) ? (reg5xh & 0x07) : 8,
- (reg5yh & 0x07) ? (reg5yh & 0x07) : 8 );
-
- pci_read_config_byte(bmide_dev, 0x59, ®5xh);
- pci_read_config_byte(bmide_dev, 0x5d, ®5yh);
- p += sprintf(p,
- "Command Act. Count: %dT"
- " %dT\n"
- "Command Rec. Count: %dT"
- " %dT\n\n",
- (reg5xh & 0x70) ? ((reg5xh & 0x70) >> 4) : 8,
- (reg5yh & 0x70) ? ((reg5yh & 0x70) >> 4) : 8,
- (reg5xh & 0x0f) ? (reg5xh & 0x0f) : 16,
- (reg5yh & 0x0f) ? (reg5yh & 0x0f) : 16 );
-
- p += sprintf(p,
- "----------------drive0-----------drive1"
- "------------drive0-----------drive1------\n\n");
- p += sprintf(p,
- "DMA enabled: %s %s"
- " %s %s\n",
- (c0&0x20) ? "Yes" : "No ",
- (c0&0x40) ? "Yes" : "No ",
- (c1&0x20) ? "Yes" : "No ",
- (c1&0x40) ? "Yes" : "No " );
-
- pci_read_config_byte(bmide_dev, 0x54, ®5xh);
- pci_read_config_byte(bmide_dev, 0x55, ®5yh);
- q = "FIFO threshold: %2d Words %2d Words"
- " %2d Words %2d Words\n";
- if (rev < 0xc1) {
- if ((rev == 0x20) &&
- (pci_read_config_byte(bmide_dev, 0x4f, &tmp), (tmp &= 0x20))) {
- p += sprintf(p, q, 8, 8, 8, 8);
- } else {
- p += sprintf(p, q,
- (reg5xh & 0x03) + 12,
- ((reg5xh & 0x30)>>4) + 12,
- (reg5yh & 0x03) + 12,
- ((reg5yh & 0x30)>>4) + 12 );
- }
- } else {
- int t1 = (tmp = (reg5xh & 0x03)) ? (tmp << 3) : 4;
- int t2 = (tmp = ((reg5xh & 0x30)>>4)) ? (tmp << 3) : 4;
- int t3 = (tmp = (reg5yh & 0x03)) ? (tmp << 3) : 4;
- int t4 = (tmp = ((reg5yh & 0x30)>>4)) ? (tmp << 3) : 4;
- p += sprintf(p, q, t1, t2, t3, t4);
- }
-
-#if 0
- p += sprintf(p,
- "FIFO threshold: %2d Words %2d Words"
- " %2d Words %2d Words\n",
- (reg5xh & 0x03) + 12,
- ((reg5xh & 0x30)>>4) + 12,
- (reg5yh & 0x03) + 12,
- ((reg5yh & 0x30)>>4) + 12 );
-#endif
-
- p += sprintf(p,
- "FIFO mode: %s %s %s %s\n",
- fifo[((reg5xh & 0x0c) >> 2)],
- fifo[((reg5xh & 0xc0) >> 6)],
- fifo[((reg5yh & 0x0c) >> 2)],
- fifo[((reg5yh & 0xc0) >> 6)] );
-
- pci_read_config_byte(bmide_dev, 0x5a, ®5xh);
- pci_read_config_byte(bmide_dev, 0x5b, ®5xh1);
- pci_read_config_byte(bmide_dev, 0x5e, ®5yh);
- pci_read_config_byte(bmide_dev, 0x5f, ®5yh1);
-
- p += sprintf(p,/*
- "------------------drive0-----------drive1"
- "------------drive0-----------drive1------\n")*/
- "Dt RW act. Cnt %2dT %2dT"
- " %2dT %2dT\n"
- "Dt RW rec. Cnt %2dT %2dT"
- " %2dT %2dT\n\n",
- (reg5xh & 0x70) ? ((reg5xh & 0x70) >> 4) : 8,
- (reg5xh1 & 0x70) ? ((reg5xh1 & 0x70) >> 4) : 8,
- (reg5yh & 0x70) ? ((reg5yh & 0x70) >> 4) : 8,
- (reg5yh1 & 0x70) ? ((reg5yh1 & 0x70) >> 4) : 8,
- (reg5xh & 0x0f) ? (reg5xh & 0x0f) : 16,
- (reg5xh1 & 0x0f) ? (reg5xh1 & 0x0f) : 16,
- (reg5yh & 0x0f) ? (reg5yh & 0x0f) : 16,
- (reg5yh1 & 0x0f) ? (reg5yh1 & 0x0f) : 16 );
-
- p += sprintf(p,
- "-----------------------------------UDMA Timings"
- "--------------------------------\n\n");
-
- pci_read_config_byte(bmide_dev, 0x56, ®5xh);
- pci_read_config_byte(bmide_dev, 0x57, ®5yh);
- p += sprintf(p,
- "UDMA: %s %s"
- " %s %s\n"
- "UDMA timings: %s %s"
- " %s %s\n\n",
- (reg5xh & 0x08) ? "OK" : "No",
- (reg5xh & 0x80) ? "OK" : "No",
- (reg5yh & 0x08) ? "OK" : "No",
- (reg5yh & 0x80) ? "OK" : "No",
- udmaT[(reg5xh & 0x07)],
- udmaT[(reg5xh & 0x70) >> 4],
- udmaT[reg5yh & 0x07],
- udmaT[(reg5yh & 0x70) >> 4] );
-
- return p-buffer; /* => must be less than 4k! */
-}
-#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
-
/**
* ali_set_pio_mode - set host controller for PIO mode
* @drive: drive
static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- int s_time, a_time, c_time;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
+ int s_time = t->setup, a_time = t->active, c_time = t->cycle;
u8 s_clc, a_clc, r_clc;
unsigned long flags;
- int bus_speed = system_bus_clock();
+ int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
int port = hwif->channel ? 0x5c : 0x58;
int portFIFO = hwif->channel ? 0x55 : 0x54;
u8 cd_dma_fifo = 0;
int unit = drive->select.b.unit & 1;
- s_time = ide_pio_timings[pio].setup_time;
- a_time = ide_pio_timings[pio].active_time;
if ((s_clc = (s_time * bus_speed + 999) / 1000) >= 8)
s_clc = 0;
if ((a_clc = (a_time * bus_speed + 999) / 1000) >= 8)
a_clc = 0;
- c_time = ide_pio_timings[pio].cycle_time;
-
-#if 0
- if ((r_clc = ((c_time - s_time - a_time) * bus_speed + 999) / 1000) >= 16)
- r_clc = 0;
-#endif
if (!(r_clc = (c_time * bus_speed + 999) / 1000 - a_clc - s_clc)) {
r_clc = 1;
pci_write_config_byte(dev, port, s_clc);
pci_write_config_byte(dev, port+drive->select.b.unit+2, (a_clc << 4) | r_clc);
local_irq_restore(flags);
-
- /*
- * setup active rec
- * { 70, 165, 365 }, PIO Mode 0
- * { 50, 125, 208 }, PIO Mode 1
- * { 30, 100, 110 }, PIO Mode 2
- * { 30, 80, 70 }, PIO Mode 3 with IORDY
- * { 25, 70, 25 }, PIO Mode 4 with IORDY ns
- * { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
- */
}
/**
* The actual rules for the ALi are:
* No UDMA on revisions <= 0x20
* Disk only for revisions < 0xC2
- * Not WDC drives for revisions < 0xC2
- *
- * FIXME: WDC ifdef needs to die
+ * Not WDC drives on M1543C-E (?)
*/
static u8 ali_udma_filter(ide_drive_t *drive)
if (m5229_revision > 0x20 && m5229_revision < 0xC2) {
if (drive->media != ide_disk)
return 0;
-#ifndef CONFIG_WDC_ALI15X3
- if (chip_is_1543c_e && strstr(drive->id->model, "WDC "))
+ if (chip_is_1543c_e && strstr(drive->id->model, "WDC ") &&
+ wdc_udma == 0)
return 0;
-#endif
}
return drive->hwif->ultra_mask;
static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 speed1 = speed;
u8 unit = (drive->select.b.unit & 0x01);
u8 tmpbyte = 0x00;
int m5229_udma = (hwif->channel) ? 0x57 : 0x56;
- if (speed < XFER_PIO_0)
- return;
-
if (speed == XFER_UDMA_6)
speed1 = 0x47;
}
/**
- * ali15x3_config_drive_for_dma - configure for DMA
- * @drive: drive to configure
- *
- * Configure a drive for DMA operation. If DMA is not possible we
- * drop the drive into PIO mode instead.
- */
-
-static int ali15x3_config_drive_for_dma(ide_drive_t *drive)
-{
- drive->init_speed = 0;
-
- if (ide_tune_dma(drive))
- return 0;
-
- ide_set_max_pio(drive);
-
- return -1;
-}
-
-/**
* ali15x3_dma_setup - begin a DMA phase
* @drive: target device
*
isa_dev = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
- if (!ali_proc) {
- ali_proc = 1;
- bmide_dev = dev;
- ide_pci_create_host_proc("ali", ali_get_info);
- }
-#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
-
local_irq_save(flags);
if (m5229_revision < 0xC2) {
* clear bit 7
*/
pci_write_config_byte(dev, 0x4b, tmpbyte & 0x7F);
+ /*
+ * check m1533, 0x5e, bit 1~4 == 1001 => & 00011110 = 00010010
+ */
+ if (m5229_revision >= 0x20 && isa_dev) {
+ pci_read_config_byte(isa_dev, 0x5e, &tmpbyte);
+ chip_is_1543c_e = ((tmpbyte & 0x1e) == 0x12) ? 1: 0;
+ }
goto out;
}
pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02);
}
}
+
out:
+ /*
+ * CD_ROM DMA on (m5229, 0x53, bit0)
+ * Enable this bit even if we want to use PIO.
+ * PIO FIFO off (m5229, 0x53, bit1)
+ * The hardware will use 0x54h and 0x55h to control PIO FIFO.
+ * (Not on later devices it seems)
+ *
+ * 0x53 changes meaning on later revs - we must no touch
+ * bit 1 on them. Need to check if 0x20 is the right break.
+ */
+ if (m5229_revision >= 0x20) {
+ pci_read_config_byte(dev, 0x53, &tmpbyte);
+
+ if (m5229_revision <= 0x20)
+ tmpbyte = (tmpbyte & (~0x02)) | 0x01;
+ else if (m5229_revision == 0xc7 || m5229_revision == 0xc8)
+ tmpbyte |= 0x03;
+ else
+ tmpbyte |= 0x01;
+
+ pci_write_config_byte(dev, 0x53, tmpbyte);
+ }
pci_dev_put(north);
pci_dev_put(isa_dev);
local_irq_restore(flags);
pdev->subsystem_device == 0x10AF)
return 1;
+ /* Mitac 8317 (Winbook-A) and relatives */
+ if (pdev->subsystem_vendor == 0x1071 &&
+ pdev->subsystem_device == 0x8317)
+ return 1;
+
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
}
/**
- * ata66_ali15x3 - check for UDMA 66 support
+ * ali_cable_detect - cable detection
* @hwif: IDE interface
*
* This checks if the controller and the cable are capable
* FIXME: frobs bits that are not defined on newer ALi devicea
*/
-static u8 __devinit ata66_ali15x3(ide_hwif_t *hwif)
+static u8 __devinit ali_cable_detect(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long flags;
u8 cbl = ATA_CBL_PATA40, tmpbyte;
if ((tmpbyte & (1 << hwif->channel)) == 0)
cbl = ATA_CBL_PATA80;
}
- } else {
- /*
- * check m1533, 0x5e, bit 1~4 == 1001 => & 00011110 = 00010010
- */
- pci_read_config_byte(isa_dev, 0x5e, &tmpbyte);
- chip_is_1543c_e = ((tmpbyte & 0x1e) == 0x12) ? 1: 0;
}
- /*
- * CD_ROM DMA on (m5229, 0x53, bit0)
- * Enable this bit even if we want to use PIO
- * PIO FIFO off (m5229, 0x53, bit1)
- * The hardware will use 0x54h and 0x55h to control PIO FIFO
- * (Not on later devices it seems)
- *
- * 0x53 changes meaning on later revs - we must no touch
- * bit 1 on them. Need to check if 0x20 is the right break
- */
-
- pci_read_config_byte(dev, 0x53, &tmpbyte);
-
- if(m5229_revision <= 0x20)
- tmpbyte = (tmpbyte & (~0x02)) | 0x01;
- else if (m5229_revision == 0xc7 || m5229_revision == 0xc8)
- tmpbyte |= 0x03;
- else
- tmpbyte |= 0x01;
-
- pci_write_config_byte(dev, 0x53, tmpbyte);
-
local_irq_restore(flags);
return cbl;
}
-/**
- * init_hwif_common_ali15x3 - Set up ALI IDE hardware
- * @hwif: IDE interface
- *
- * Initialize the IDE structure side of the ALi 15x3 driver.
- */
-
-static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
-{
- hwif->autodma = 0;
- hwif->set_pio_mode = &ali_set_pio_mode;
- hwif->set_dma_mode = &ali_set_dma_mode;
- hwif->udma_filter = &ali_udma_filter;
-
- /* don't use LBA48 DMA on ALi devices before rev 0xC5 */
- hwif->no_lba48_dma = (m5229_revision <= 0xC4) ? 1 : 0;
-
- if (!hwif->dma_base) {
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
- return;
- }
-
- if (m5229_revision > 0x20)
- hwif->atapi_dma = 1;
-
- if (m5229_revision <= 0x20)
- hwif->ultra_mask = 0x00; /* no udma */
- else if (m5229_revision < 0xC2)
- hwif->ultra_mask = 0x07; /* udma0-2 */
- else if (m5229_revision == 0xC2 || m5229_revision == 0xC3)
- hwif->ultra_mask = 0x1f; /* udma0-4 */
- else if (m5229_revision == 0xC4)
- hwif->ultra_mask = 0x3f; /* udma0-5 */
- else
- hwif->ultra_mask = 0x7f; /* udma0-6 */
-
- hwif->mwdma_mask = 0x07;
- hwif->swdma_mask = 0x07;
-
- if (m5229_revision >= 0x20) {
- /*
- * M1543C or newer for DMAing
- */
- hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
- hwif->dma_setup = &ali15x3_dma_setup;
- if (!noautodma)
- hwif->autodma = 1;
-
- if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = ata66_ali15x3(hwif);
- }
- hwif->drives[0].autodma = hwif->autodma;
- hwif->drives[1].autodma = hwif->autodma;
-}
-
+#if !defined(CONFIG_SPARC64) && !defined(CONFIG_PPC)
/**
* init_hwif_ali15x3 - Initialize the ALI IDE x86 stuff
* @hwif: interface to configure
*
* Obtain the IRQ tables for an ALi based IDE solution on the PC
* class platforms. This part of the code isn't applicable to the
- * Sparc systems
+ * Sparc and PowerPC systems.
*/
static void __devinit init_hwif_ali15x3 (ide_hwif_t *hwif)
{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 ideic, inmir;
s8 irq_routing_table[] = { -1, 9, 3, 10, 4, 5, 7, 6,
1, 11, 0, 12, 0, 14, 0, 15 };
int irq = -1;
- if (hwif->pci_dev->device == PCI_DEVICE_ID_AL_M5229)
+ if (dev->device == PCI_DEVICE_ID_AL_M5229)
hwif->irq = hwif->channel ? 15 : 14;
if (isa_dev) {
if(irq >= 0)
hwif->irq = irq;
}
-
- init_hwif_common_ali15x3(hwif);
}
+#else
+#define init_hwif_ali15x3 NULL
+#endif /* !defined(CONFIG_SPARC64) && !defined(CONFIG_PPC) */
/**
* init_dma_ali15x3 - set up DMA on ALi15x3
* @hwif: IDE interface
- * @dmabase: DMA interface base PCI address
+ * @d: IDE port info
*
- * Set up the DMA functionality on the ALi 15x3. For the ALi
- * controllers this is generic so we can let the generic code do
- * the actual work.
+ * Set up the DMA functionality on the ALi 15x3.
*/
-static void __devinit init_dma_ali15x3 (ide_hwif_t *hwif, unsigned long dmabase)
+static int __devinit init_dma_ali15x3(ide_hwif_t *hwif,
+ const struct ide_port_info *d)
{
- if (m5229_revision < 0x20)
- return;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long base = ide_pci_dma_base(hwif, d);
+
+ if (base == 0)
+ return -1;
+
+ hwif->dma_base = base;
+
+ if (ide_pci_check_simplex(hwif, d) < 0)
+ return -1;
+
+ if (ide_pci_set_master(dev, d->name) < 0)
+ return -1;
+
if (!hwif->channel)
- outb(inb(dmabase + 2) & 0x60, dmabase + 2);
- ide_setup_dma(hwif, dmabase, 8);
+ outb(inb(base + 2) & 0x60, base + 2);
+
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
+ hwif->name, base, base + 7);
+
+ if (ide_allocate_dma_engine(hwif))
+ return -1;
+
+ hwif->dma_ops = &sff_dma_ops;
+
+ return 0;
}
-static ide_pci_device_t ali15x3_chipset __devinitdata = {
+static const struct ide_port_ops ali_port_ops = {
+ .set_pio_mode = ali_set_pio_mode,
+ .set_dma_mode = ali_set_dma_mode,
+ .udma_filter = ali_udma_filter,
+ .cable_detect = ali_cable_detect,
+};
+
+static const struct ide_dma_ops ali_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ali15x3_dma_setup,
+ .dma_exec_cmd = ide_dma_exec_cmd,
+ .dma_start = ide_dma_start,
+ .dma_end = __ide_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timeout = ide_dma_timeout,
+};
+
+static const struct ide_port_info ali15x3_chipset __devinitdata = {
.name = "ALI15X3",
.init_chipset = init_chipset_ali15x3,
.init_hwif = init_hwif_ali15x3,
.init_dma = init_dma_ali15x3,
- .autodma = AUTODMA,
- .bootable = ON_BOARD,
+ .port_ops = &ali_port_ops,
.pio_mask = ATA_PIO5,
+ .swdma_mask = ATA_SWDMA2,
+ .mwdma_mask = ATA_MWDMA2,
};
/**
static int __devinit alim15x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct pci_device_id ati_rs100[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100) },
- { },
- };
+ struct ide_port_info d = ali15x3_chipset;
+ u8 rev = dev->revision, idx = id->driver_data;
- ide_pci_device_t *d = &ali15x3_chipset;
+ /* don't use LBA48 DMA on ALi devices before rev 0xC5 */
+ if (rev <= 0xC4)
+ d.host_flags |= IDE_HFLAG_NO_LBA48_DMA;
+
+ if (rev >= 0x20) {
+ if (rev == 0x20)
+ d.host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
+
+ if (rev < 0xC2)
+ d.udma_mask = ATA_UDMA2;
+ else if (rev == 0xC2 || rev == 0xC3)
+ d.udma_mask = ATA_UDMA4;
+ else if (rev == 0xC4)
+ d.udma_mask = ATA_UDMA5;
+ else
+ d.udma_mask = ATA_UDMA6;
+
+ d.dma_ops = &ali_dma_ops;
+ } else {
+ d.host_flags |= IDE_HFLAG_NO_DMA;
+
+ d.mwdma_mask = d.swdma_mask = 0;
+ }
- if (pci_dev_present(ati_rs100))
- printk(KERN_WARNING "alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.\n");
+ if (idx == 0)
+ d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
-#if defined(CONFIG_SPARC64)
- d->init_hwif = init_hwif_common_ali15x3;
-#endif /* CONFIG_SPARC64 */
- return ide_setup_pci_device(dev, d);
+ return ide_pci_init_one(dev, &d, NULL);
}
-static struct pci_device_id alim15x3_pci_tbl[] = {
- { PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+static const struct pci_device_id alim15x3_pci_tbl[] = {
+ { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), 0 },
+ { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, alim15x3_pci_tbl);
.name = "ALI15x3_IDE",
.id_table = alim15x3_pci_tbl,
.probe = alim15x3_init_one,
+ .remove = ide_pci_remove,
};
static int __init ali15x3_ide_init(void)
return ide_pci_register_driver(&driver);
}
+static void __exit ali15x3_ide_exit(void)
+{
+ return pci_unregister_driver(&driver);
+}
+
module_init(ali15x3_ide_init);
+module_exit(ali15x3_ide_exit);
MODULE_AUTHOR("Michael Aubry, Andrzej Krzysztofowicz, CJ, Andre Hedrick, Alan Cox");
MODULE_DESCRIPTION("PCI driver module for ALi 15x3 IDE");