/*
- * linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02
+ * linux/drivers/ide/pci/alim15x3.c Version 0.26 Jul 14 2007
*
* Copyright (C) 1998-2000 Michel Aubry, Maintainer
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
* May be copied or modified under the terms of the GNU General Public License
* Copyright (C) 2002 Alan Cox <alan@redhat.com>
* ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
+ * Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
*
* (U)DMA capable version of ali 1533/1543(C), 1535(D)
*
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
+#include <linux/dmi.h>
#include <asm/io.h>
static u8 chip_is_1543c_e;
static struct pci_dev *isa_dev;
-#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_PROC_FS)
+#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
#include <linux/stat.h>
#include <linux/proc_fs.h>
return p-buffer; /* => must be less than 4k! */
}
-#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_PROC_FS) */
+#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
/**
- * ali15x3_tune_drive - set up a drive
- * @drive: drive to tune
- * @pio: unused
+ * ali_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Select the best PIO timing for the drive in question. Then
- * program the controller for this drive set up
+ * Program the controller for the given PIO mode.
*/
-
-static void ali15x3_tune_drive (ide_drive_t *drive, u8 pio)
+
+static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- ide_pio_data_t d;
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
int s_time, a_time, c_time;
u8 cd_dma_fifo = 0;
int unit = drive->select.b.unit & 1;
- pio = ide_get_best_pio_mode(drive, pio, 5, &d);
s_time = ide_pio_timings[pio].setup_time;
a_time = ide_pio_timings[pio].active_time;
if ((s_clc = (s_time * bus_speed + 999) / 1000) >= 8)
* { 25, 70, 25 }, PIO Mode 4 with IORDY ns
* { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
*/
-
}
/**
- * ali15x3_can_ultra - check for ultra DMA support
- * @drive: drive to do the check
+ * ali_udma_filter - compute UDMA mask
+ * @drive: IDE device
*
- * Check the drive and controller revisions. Return 0 if UDMA is
- * not available, or 1 if UDMA can be used. The actual rules for
- * the ALi are
+ * Return available UDMA modes.
+ *
+ * The actual rules for the ALi are:
* No UDMA on revisions <= 0x20
* Disk only for revisions < 0xC2
* Not WDC drives for revisions < 0xC2
*
* FIXME: WDC ifdef needs to die
*/
-
-static u8 ali15x3_can_ultra (ide_drive_t *drive)
-{
-#ifndef CONFIG_WDC_ALI15X3
- struct hd_driveid *id = drive->id;
-#endif /* CONFIG_WDC_ALI15X3 */
-
- if (m5229_revision <= 0x20) {
- return 0;
- } else if ((m5229_revision < 0xC2) &&
-#ifndef CONFIG_WDC_ALI15X3
- ((chip_is_1543c_e && strstr(id->model, "WDC ")) ||
- (drive->media!=ide_disk))) {
-#else /* CONFIG_WDC_ALI15X3 */
- (drive->media!=ide_disk)) {
-#endif /* CONFIG_WDC_ALI15X3 */
- return 0;
- } else {
- return 1;
- }
-}
-/**
- * ali15x3_ratemask - generate DMA mode list
- * @drive: drive to compute against
- *
- * Generate a list of the available DMA modes for the drive.
- * FIXME: this function contains lots of bogus masking we can dump
- *
- * Return the highest available mode (UDMA33, UDMA66, UDMA100,..)
- */
-
-static u8 ali15x3_ratemask (ide_drive_t *drive)
+static u8 ali_udma_filter(ide_drive_t *drive)
{
- u8 mode = 0, can_ultra = ali15x3_can_ultra(drive);
-
- if (m5229_revision > 0xC4 && can_ultra) {
- mode = 4;
- } else if (m5229_revision == 0xC4 && can_ultra) {
- mode = 3;
- } else if (m5229_revision >= 0xC2 && can_ultra) {
- mode = 2;
- } else if (can_ultra) {
- return 1;
- } else {
- return 0;
+ if (m5229_revision > 0x20 && m5229_revision < 0xC2) {
+ if (drive->media != ide_disk)
+ return 0;
+#ifndef CONFIG_WDC_ALI15X3
+ if (chip_is_1543c_e && strstr(drive->id->model, "WDC "))
+ return 0;
+#endif
}
- /*
- * If the drive sees no suitable cable then UDMA 33
- * is the highest permitted mode
- */
-
- if (!eighty_ninty_three(drive))
- mode = min(mode, (u8)1);
- return mode;
+ return drive->hwif->ultra_mask;
}
/**
- * ali15x3_tune_chipset - set up chiset for new speed
- * @drive: drive to configure for
- * @xferspeed: desired speed
+ * ali_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
* Configure the hardware for the desired IDE transfer mode.
- * We also do the needed drive configuration through helpers
*/
-
-static int ali15x3_tune_chipset (ide_drive_t *drive, u8 xferspeed)
+
+static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
- u8 speed = ide_rate_filter(ali15x3_ratemask(drive), xferspeed);
u8 speed1 = speed;
u8 unit = (drive->select.b.unit & 0x01);
u8 tmpbyte = 0x00;
int m5229_udma = (hwif->channel) ? 0x57 : 0x56;
+ if (speed < XFER_PIO_0)
+ return;
+
if (speed == XFER_UDMA_6)
speed1 = 0x47;
tmpbyte &= ultra_enable;
pci_write_config_byte(dev, m5229_udma, tmpbyte);
- if (speed < XFER_SW_DMA_0)
- ali15x3_tune_drive(drive, speed);
+ /*
+ * FIXME: Oh, my... DMA timings are never set.
+ */
} else {
pci_read_config_byte(dev, m5229_udma, &tmpbyte);
tmpbyte &= (0x0f << ((1-unit) << 2));
pci_write_config_byte(dev, 0x4b, tmpbyte);
}
}
- return (ide_config_drive_speed(drive, speed));
-}
-
-
-/**
- * config_chipset_for_dma - set up DMA mode
- * @drive: drive to configure for
- *
- * Place a drive into DMA mode and tune the chipset for
- * the selected speed.
- *
- * Returns true if DMA mode can be used
- */
-
-static int config_chipset_for_dma (ide_drive_t *drive)
-{
- u8 speed = ide_dma_speed(drive, ali15x3_ratemask(drive));
-
- if (!(speed))
- return 0;
-
- (void) ali15x3_tune_chipset(drive, speed);
- return ide_dma_enable(drive);
-}
-
-/**
- * ali15x3_config_drive_for_dma - configure for DMA
- * @drive: drive to configure
- *
- * Configure a drive for DMA operation. If DMA is not possible we
- * drop the drive into PIO mode instead.
- *
- * FIXME: exactly what are we trying to return here
- */
-
-static int ali15x3_config_drive_for_dma(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct hd_driveid *id = drive->id;
-
- if ((m5229_revision<=0x20) && (drive->media!=ide_disk))
- return hwif->ide_dma_off_quietly(drive);
-
- drive->init_speed = 0;
-
- if ((id != NULL) && ((id->capability & 1) != 0) && drive->autodma) {
- /* Consult the list of known "bad" drives */
- if (__ide_dma_bad_drive(drive))
- goto ata_pio;
- if ((id->field_valid & 4) && (m5229_revision >= 0xC2)) {
- if (id->dma_ultra & hwif->ultra_mask) {
- /* Force if Capable UltraDMA */
- int dma = config_chipset_for_dma(drive);
- if ((id->field_valid & 2) && !dma)
- goto try_dma_modes;
- }
- } else if (id->field_valid & 2) {
-try_dma_modes:
- if ((id->dma_mword & hwif->mwdma_mask) ||
- (id->dma_1word & hwif->swdma_mask)) {
- /* Force if Capable regular DMA modes */
- if (!config_chipset_for_dma(drive))
- goto no_dma_set;
- }
- } else if (__ide_dma_good_drive(drive) &&
- (id->eide_dma_time < 150)) {
- /* Consult the list of known "good" drives */
- if (!config_chipset_for_dma(drive))
- goto no_dma_set;
- } else {
- goto ata_pio;
- }
- } else {
-ata_pio:
- hwif->tuneproc(drive, 255);
-no_dma_set:
- return hwif->ide_dma_off_quietly(drive);
- }
- return hwif->ide_dma_on(drive);
}
/**
u8 tmpbyte;
struct pci_dev *north = pci_get_slot(dev->bus, PCI_DEVFN(0,0));
- pci_read_config_byte(dev, PCI_REVISION_ID, &m5229_revision);
+ m5229_revision = dev->revision;
isa_dev = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
-#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_PROC_FS)
+#if defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
if (!ali_proc) {
ali_proc = 1;
bmide_dev = dev;
ide_pci_create_host_proc("ali", ali_get_info);
}
-#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_PROC_FS) */
+#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
local_irq_save(flags);
return 0;
}
+/*
+ * Cable special cases
+ */
+
+static const struct dmi_system_id cable_dmi_table[] = {
+ {
+ .ident = "HP Pavilion N5430",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+ DMI_MATCH(DMI_BOARD_VERSION, "OmniBook N32N-736"),
+ },
+ },
+ {
+ .ident = "Toshiba Satellite S1800-814",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "S1800-814"),
+ },
+ },
+ { }
+};
+
+static int ali_cable_override(struct pci_dev *pdev)
+{
+ /* Fujitsu P2000 */
+ if (pdev->subsystem_vendor == 0x10CF &&
+ pdev->subsystem_device == 0x10AF)
+ return 1;
+
+ /* Systems by DMI */
+ if (dmi_check_system(cable_dmi_table))
+ return 1;
+
+ return 0;
+}
+
/**
* ata66_ali15x3 - check for UDMA 66 support
* @hwif: IDE interface
* FIXME: frobs bits that are not defined on newer ALi devicea
*/
-static unsigned int __devinit ata66_ali15x3 (ide_hwif_t *hwif)
+static u8 __devinit ata66_ali15x3(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
- unsigned int ata66 = 0;
- u8 cable_80_pin[2] = { 0, 0 };
-
unsigned long flags;
- u8 tmpbyte;
+ u8 cbl = ATA_CBL_PATA40, tmpbyte;
local_irq_save(flags);
if (m5229_revision >= 0xC2) {
/*
- * Ultra66 cable detection (from Host View)
- * m5229, 0x4a, bit0: primary, bit1: secondary 80 pin
+ * m5229 80-pin cable detection (from Host View)
+ *
+ * 0x4a bit0 is 0 => primary channel has 80-pin
+ * 0x4a bit1 is 0 => secondary channel has 80-pin
+ *
+ * Certain laptops use short but suitable cables
+ * and don't implement the detect logic.
*/
- pci_read_config_byte(dev, 0x4a, &tmpbyte);
- /*
- * 0x4a, bit0 is 0 => primary channel
- * has 80-pin (from host view)
- */
- if (!(tmpbyte & 0x01)) cable_80_pin[0] = 1;
- /*
- * 0x4a, bit1 is 0 => secondary channel
- * has 80-pin (from host view)
- */
- if (!(tmpbyte & 0x02)) cable_80_pin[1] = 1;
- /*
- * Allow ata66 if cable of current channel has 80 pins
- */
- ata66 = (hwif->channel)?cable_80_pin[1]:cable_80_pin[0];
+ if (ali_cable_override(dev))
+ cbl = ATA_CBL_PATA40_SHORT;
+ else {
+ pci_read_config_byte(dev, 0x4a, &tmpbyte);
+ if ((tmpbyte & (1 << hwif->channel)) == 0)
+ cbl = ATA_CBL_PATA80;
+ }
} else {
/*
* check m1533, 0x5e, bit 1~4 == 1001 => & 00011110 = 00010010
local_irq_restore(flags);
- return(ata66);
+ return cbl;
}
/**
static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
{
hwif->autodma = 0;
- hwif->tuneproc = &ali15x3_tune_drive;
- hwif->speedproc = &ali15x3_tune_chipset;
+ hwif->set_pio_mode = &ali_set_pio_mode;
+ hwif->set_dma_mode = &ali_set_dma_mode;
+ hwif->udma_filter = &ali_udma_filter;
/* don't use LBA48 DMA on ALi devices before rev 0xC5 */
hwif->no_lba48_dma = (m5229_revision <= 0xC4) ? 1 : 0;
return;
}
- hwif->atapi_dma = 1;
+ /*
+ * check in ->init_dma guarantees m5229_revision >= 0x20 here
+ */
if (m5229_revision > 0x20)
- hwif->ultra_mask = 0x7f;
+ hwif->atapi_dma = 1;
+
+ if (m5229_revision <= 0x20)
+ hwif->ultra_mask = 0x00; /* no udma */
+ else if (m5229_revision < 0xC2)
+ hwif->ultra_mask = 0x07; /* udma0-2 */
+ else if (m5229_revision == 0xC2 || m5229_revision == 0xC3)
+ hwif->ultra_mask = 0x1f; /* udma0-4 */
+ else if (m5229_revision == 0xC4)
+ hwif->ultra_mask = 0x3f; /* udma0-5 */
+ else
+ hwif->ultra_mask = 0x7f; /* udma0-6 */
+
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
- if (m5229_revision >= 0x20) {
- /*
- * M1543C or newer for DMAing
- */
- hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
- hwif->dma_setup = &ali15x3_dma_setup;
- if (!noautodma)
- hwif->autodma = 1;
- if (!(hwif->udma_four))
- hwif->udma_four = ata66_ali15x3(hwif);
- }
+ hwif->dma_setup = &ali15x3_dma_setup;
+
+ if (hwif->cbl != ATA_CBL_PATA40_SHORT)
+ hwif->cbl = ata66_ali15x3(hwif);
+
+ if (!noautodma)
+ hwif->autodma = 1;
+
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
{
if (m5229_revision < 0x20)
return;
- if (!(hwif->channel))
- hwif->OUTB(hwif->INB(dmabase+2) & 0x60, dmabase+2);
+ if (!hwif->channel)
+ outb(inb(dmabase + 2) & 0x60, dmabase + 2);
ide_setup_dma(hwif, dmabase, 8);
}
.init_chipset = init_chipset_ali15x3,
.init_hwif = init_hwif_ali15x3,
.init_dma = init_dma_ali15x3,
- .channels = 2,
.autodma = AUTODMA,
.bootable = ON_BOARD,
+ .pio_mask = ATA_PIO5,
};
/**
.probe = alim15x3_init_one,
};
-static int ali15x3_ide_init(void)
+static int __init ali15x3_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff