* May be copied or modified under the terms of the GNU General Public License
* Based in part on the ITE vendor provided SCSI driver.
*
- * Documentation available from
- * http://www.ite.com.tw/pc/IT8212F_V04.pdf
- * Some other documents are NDA.
+ * Documentation:
+ * Datasheet is freely available, some other documents under NDA.
*
* The ITE8212 isn't exactly a standard IDE controller. It has two
* modes. In pass through mode then it is an IDE controller. In its smart
#include <linux/types.h>
#include <linux/module.h>
+#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>
#define DRV_NAME "it821x"
+#define QUIRK_VORTEX86 1
+
struct it821x_dev
{
unsigned int smart:1, /* Are we in smart raid mode */
u16 pio[2]; /* Cached PIO values */
u16 mwdma[2]; /* Cached MWDMA values */
u16 udma[2]; /* Cached UDMA values (per drive) */
+ u16 quirks;
};
#define ATA_66 0
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair;
+ ide_drive_t *pair = ide_get_pair_dev(drive);
int clock, altclock, sel = 0;
u8 unit = drive->dn & 1, v;
- pair = &hwif->drives[1 - unit];
-
if(itdev->want[0][0] > itdev->want[1][0]) {
clock = itdev->want[0][1];
altclock = itdev->want[1][1];
/**
* it821x_set_pio_mode - set host controller for PIO mode
+ * @hwif: port
* @drive: drive
- * @pio: PIO mode number
*
* Tune the host to the desired PIO mode taking into the consideration
* the maximum PIO mode supported by the other device on the cable.
*/
-static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- ide_drive_t *pair;
+ ide_drive_t *pair = ide_get_pair_dev(drive);
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
u8 unit = drive->dn & 1, set_pio = pio;
/* Spec says 89 ref driver uses 88 */
static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
- pair = &hwif->drives[1 - unit];
-
/*
* Compute the best PIO mode we can for a given device. We must
* pick a speed that does not cause problems with the other device
* on the cable.
*/
if (pair) {
- u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
+ u8 pair_pio = pair->pio_mode - XFER_PIO_0;
/* trim PIO to the slowest of the master/slave */
if (pair_pio < set_pio)
set_pio = pair_pio;
/**
* it821x_set_dma_mode - set host controller for DMA mode
+ * @hwif: port
* @drive: drive
- * @speed: DMA mode
*
* Tune the ITE chipset for the desired DMA mode.
*/
-static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
+ const u8 speed = drive->dma_mode;
+
/*
* MWDMA tuning is really hard because our MWDMA and PIO
* timings are kept in the same place. We can switch in the
static struct ide_dma_ops it821x_pass_through_dma_ops = {
.dma_host_set = ide_dma_host_set,
.dma_setup = ide_dma_setup,
- .dma_exec_cmd = ide_dma_exec_cmd,
.dma_start = it821x_dma_start,
.dma_end = it821x_dma_end,
.dma_test_irq = ide_dma_test_irq,
- .dma_timeout = ide_dma_timeout,
.dma_lost_irq = ide_dma_lost_irq,
+ .dma_timer_expiry = ide_dma_sff_timer_expiry,
+ .dma_sff_read_status = ide_dma_sff_read_status,
};
/**
* this is necessary.
*/
- pci_read_config_byte(dev, 0x08, &conf);
- if (conf == 0x10) {
+ if (dev->revision == 0x10) {
idev->timing10 = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (idev->smart == 0)
hwif->ultra_mask = ATA_UDMA6;
hwif->mwdma_mask = ATA_MWDMA2;
+
+ /* Vortex86SX quirk: prevent Ultra-DMA mode to fix BadCRC issue */
+ if (idev->quirks & QUIRK_VORTEX86) {
+ if (dev->revision == 0x11)
+ hwif->ultra_mask = 0;
+ }
}
static void it8212_disable_raid(struct pci_dev *dev)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
-static unsigned int init_chipset_it821x(struct pci_dev *dev)
+static int init_chipset_it821x(struct pci_dev *dev)
{
u8 conf;
static char *mode[2] = { "pass through", "smart" };
return -ENOMEM;
}
+ itdevs->quirks = id->driver_data;
+
rc = ide_pci_init_one(dev, &it821x_chipset, itdevs);
if (rc)
kfree(itdevs);
static const struct pci_device_id it821x_pci_tbl[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
+ { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), QUIRK_VORTEX86 },
{ 0, },
};
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff