* Documentation/ide/ChangeLog.ide-tape.1995-2002
*/
+#define DRV_NAME "ide-tape"
+
#define IDETAPE_VERSION "1.20"
#include <linux/module.h>
DBG_CHRDEV = (1 << 2),
/* all remaining procedures */
DBG_PROCS = (1 << 3),
- /* buffer alloc info (pc_stack & rq_stack) */
- DBG_PCRQ_STACK = (1 << 4),
};
/* define to see debug info */
#define IDETAPE_MAX_PC_RETRIES 3
/*
- * With each packet command, we allocate a buffer of IDETAPE_PC_BUFFER_SIZE
- * bytes. This is used for several packet commands (Not for READ/WRITE commands)
- */
-#define IDETAPE_PC_BUFFER_SIZE 256
-
-/*
- * In various places in the driver, we need to allocate storage
- * for packet commands and requests, which will remain valid while
- * we leave the driver to wait for an interrupt or a timeout event.
- */
-#define IDETAPE_PC_STACK (10 + IDETAPE_MAX_PC_RETRIES)
-
-/*
- * Some drives (for example, Seagate STT3401A Travan) require a very long
- * timeout, because they don't return an interrupt or clear their busy bit
- * until after the command completes (even retension commands).
- */
-#define IDETAPE_WAIT_CMD (900*HZ)
-
-/*
* The following parameter is used to select the point in the internal tape fifo
* in which we will start to refill the buffer. Decreasing the following
* parameter will improve the system's latency and interactive response, while
#define IDETAPE_LU_RETENSION_MASK 2
#define IDETAPE_LU_EOT_MASK 4
-/*
- * Special requests for our block device strategy routine.
- *
- * In order to service a character device command, we add special requests to
- * the tail of our block device request queue and wait for their completion.
- */
-
-enum {
- REQ_IDETAPE_PC1 = (1 << 0), /* packet command (first stage) */
- REQ_IDETAPE_PC2 = (1 << 1), /* packet command (second stage) */
- REQ_IDETAPE_READ = (1 << 2),
- REQ_IDETAPE_WRITE = (1 << 3),
-};
-
/* Error codes returned in rq->errors to the higher part of the driver. */
#define IDETAPE_ERROR_GENERAL 101
#define IDETAPE_ERROR_FILEMARK 102
#define IDETAPE_BLOCK_DESCRIPTOR 0
#define IDETAPE_CAPABILITIES_PAGE 0x2a
-/* Tape flag bits values. */
-enum {
- IDETAPE_FLAG_IGNORE_DSC = (1 << 0),
- /* 0 When the tape position is unknown */
- IDETAPE_FLAG_ADDRESS_VALID = (1 << 1),
- /* Device already opened */
- IDETAPE_FLAG_BUSY = (1 << 2),
- /* Attempt to auto-detect the current user block size */
- IDETAPE_FLAG_DETECT_BS = (1 << 3),
- /* Currently on a filemark */
- IDETAPE_FLAG_FILEMARK = (1 << 4),
- /* DRQ interrupt device */
- IDETAPE_FLAG_DRQ_INTERRUPT = (1 << 5),
- /* 0 = no tape is loaded, so we don't rewind after ejecting */
- IDETAPE_FLAG_MEDIUM_PRESENT = (1 << 6),
-};
-
/*
* Most of our global data which we need to save even as we leave the driver due
* to an interrupt or a timer event is stored in the struct defined below.
struct kref kref;
/*
- * Since a typical character device operation requires more
- * than one packet command, we provide here enough memory
- * for the maximum of interconnected packet commands.
- * The packet commands are stored in the circular array pc_stack.
- * pc_stack_index points to the last used entry, and warps around
- * to the start when we get to the last array entry.
- *
- * pc points to the current processed packet command.
- *
* failed_pc points to the last failed packet command, or contains
* NULL if we do not need to retry any packet command. This is
* required since an additional packet command is needed before the
* retry, to get detailed information on what went wrong.
*/
- /* Current packet command */
- struct ide_atapi_pc *pc;
/* Last failed packet command */
struct ide_atapi_pc *failed_pc;
- /* Packet command stack */
- struct ide_atapi_pc pc_stack[IDETAPE_PC_STACK];
- /* Next free packet command storage space */
- int pc_stack_index;
- struct request rq_stack[IDETAPE_PC_STACK];
- /* We implement a circular array */
- int rq_stack_index;
+ /* used by REQ_IDETAPE_{READ,WRITE} requests */
+ struct ide_atapi_pc queued_pc;
/*
* DSC polling variables.
/* Wasted space in each stage */
int excess_bh_size;
- /* Status/Action flags: long for set_bit */
- unsigned long flags;
/* protects the ide-tape queue */
spinlock_t lock;
static struct class *idetape_sysfs_class;
-#define to_ide_tape(obj) container_of(obj, struct ide_tape_obj, kref)
-
-#define ide_tape_g(disk) \
- container_of((disk)->private_data, struct ide_tape_obj, driver)
+static void ide_tape_release(struct kref *);
static struct ide_tape_obj *ide_tape_get(struct gendisk *disk)
{
struct ide_tape_obj *tape = NULL;
mutex_lock(&idetape_ref_mutex);
- tape = ide_tape_g(disk);
- if (tape)
- kref_get(&tape->kref);
+ tape = ide_drv_g(disk, ide_tape_obj);
+ if (tape) {
+ if (ide_device_get(tape->drive))
+ tape = NULL;
+ else
+ kref_get(&tape->kref);
+ }
mutex_unlock(&idetape_ref_mutex);
return tape;
}
-static void ide_tape_release(struct kref *);
-
static void ide_tape_put(struct ide_tape_obj *tape)
{
+ ide_drive_t *drive = tape->drive;
+
mutex_lock(&idetape_ref_mutex);
kref_put(&tape->kref, ide_tape_release);
+ ide_device_put(drive);
mutex_unlock(&idetape_ref_mutex);
}
*/
static struct ide_tape_obj *idetape_devs[MAX_HWIFS * MAX_DRIVES];
-#define ide_tape_f(file) ((file)->private_data)
-
static struct ide_tape_obj *ide_tape_chrdev_get(unsigned int i)
{
struct ide_tape_obj *tape = NULL;
}
/*
- * idetape_next_pc_storage returns a pointer to a place in which we can
- * safely store a packet command, even though we intend to leave the
- * driver. A storage space for a maximum of IDETAPE_PC_STACK packet
- * commands is allocated at initialization time.
- */
-static struct ide_atapi_pc *idetape_next_pc_storage(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
-
- debug_log(DBG_PCRQ_STACK, "pc_stack_index=%d\n", tape->pc_stack_index);
-
- if (tape->pc_stack_index == IDETAPE_PC_STACK)
- tape->pc_stack_index = 0;
- return (&tape->pc_stack[tape->pc_stack_index++]);
-}
-
-/*
- * idetape_next_rq_storage is used along with idetape_next_pc_storage.
- * Since we queue packet commands in the request queue, we need to
- * allocate a request, along with the allocation of a packet command.
- */
-
-/**************************************************************
- * *
- * This should get fixed to use kmalloc(.., GFP_ATOMIC) *
- * followed later on by kfree(). -ml *
- * *
- **************************************************************/
-
-static struct request *idetape_next_rq_storage(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
-
- debug_log(DBG_PCRQ_STACK, "rq_stack_index=%d\n", tape->rq_stack_index);
-
- if (tape->rq_stack_index == IDETAPE_PC_STACK)
- tape->rq_stack_index = 0;
- return (&tape->rq_stack[tape->rq_stack_index++]);
-}
-
-/*
* called on each failed packet command retry to analyze the request sense. We
* currently do not utilize this information.
*/
return 0;
}
-static void ide_tape_callback(ide_drive_t *drive)
+static void ide_tape_handle_dsc(ide_drive_t *);
+
+static void ide_tape_callback(ide_drive_t *drive, int dsc)
{
idetape_tape_t *tape = drive->driver_data;
- struct ide_atapi_pc *pc = tape->pc;
+ struct ide_atapi_pc *pc = drive->pc;
int uptodate = pc->error ? 0 : 1;
debug_log(DBG_PROCS, "Enter %s\n", __func__);
+ if (dsc)
+ ide_tape_handle_dsc(drive);
+
if (tape->failed_pc == pc)
tape->failed_pc = NULL;
if (pc->error)
uptodate = pc->error;
} else if (pc->c[0] == READ_POSITION && uptodate) {
- u8 *readpos = tape->pc->buf;
+ u8 *readpos = pc->buf;
debug_log(DBG_SENSE, "BOP - %s\n",
(readpos[0] & 0x80) ? "Yes" : "No");
if (readpos[0] & 0x4) {
printk(KERN_INFO "ide-tape: Block location is unknown"
"to the tape\n");
- clear_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags);
+ clear_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags);
uptodate = 0;
} else {
debug_log(DBG_SENSE, "Block Location - %u\n",
- be32_to_cpu(*(u32 *)&readpos[4]));
+ be32_to_cpup((__be32 *)&readpos[4]));
tape->partition = readpos[1];
- tape->first_frame = be32_to_cpu(*(u32 *)&readpos[4]);
- set_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags);
+ tape->first_frame = be32_to_cpup((__be32 *)&readpos[4]);
+ set_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags);
}
}
idetape_end_request(drive, uptodate, 0);
}
-static void idetape_init_pc(struct ide_atapi_pc *pc)
-{
- memset(pc->c, 0, 12);
- pc->retries = 0;
- pc->flags = 0;
- pc->req_xfer = 0;
- pc->buf = pc->pc_buf;
- pc->buf_size = IDETAPE_PC_BUFFER_SIZE;
- pc->bh = NULL;
- pc->b_data = NULL;
- pc->callback = ide_tape_callback;
-}
-
-static void idetape_create_request_sense_cmd(struct ide_atapi_pc *pc)
-{
- idetape_init_pc(pc);
- pc->c[0] = REQUEST_SENSE;
- pc->c[4] = 20;
- pc->req_xfer = 20;
-}
-
-static void idetape_init_rq(struct request *rq, u8 cmd)
-{
- blk_rq_init(NULL, rq);
- rq->cmd_type = REQ_TYPE_SPECIAL;
- rq->cmd[0] = cmd;
-}
-
-/*
- * Generate a new packet command request in front of the request queue, before
- * the current request, so that it will be processed immediately, on the next
- * pass through the driver. The function below is called from the request
- * handling part of the driver (the "bottom" part). Safe storage for the request
- * should be allocated with ide_tape_next_{pc,rq}_storage() prior to that.
- *
- * Memory for those requests is pre-allocated at initialization time, and is
- * limited to IDETAPE_PC_STACK requests. We assume that we have enough space for
- * the maximum possible number of inter-dependent packet commands.
- *
- * The higher level of the driver - The ioctl handler and the character device
- * handling functions should queue request to the lower level part and wait for
- * their completion using idetape_queue_pc_tail or idetape_queue_rw_tail.
- */
-static void idetape_queue_pc_head(ide_drive_t *drive, struct ide_atapi_pc *pc,
- struct request *rq)
-{
- struct ide_tape_obj *tape = drive->driver_data;
-
- idetape_init_rq(rq, REQ_IDETAPE_PC1);
- rq->cmd_flags |= REQ_PREEMPT;
- rq->buffer = (char *) pc;
- rq->rq_disk = tape->disk;
- ide_do_drive_cmd(drive, rq);
-}
-
-/*
- * idetape_retry_pc is called when an error was detected during the
- * last packet command. We queue a request sense packet command in
- * the head of the request list.
- */
-static void idetape_retry_pc(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
- struct ide_atapi_pc *pc;
- struct request *rq;
-
- (void)ide_read_error(drive);
- pc = idetape_next_pc_storage(drive);
- rq = idetape_next_rq_storage(drive);
- idetape_create_request_sense_cmd(pc);
- set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags);
- idetape_queue_pc_head(drive, pc, rq);
-}
-
/*
* Postpone the current request so that ide.c will be able to service requests
* from another device on the same hwgroup while we are polling for DSC.
idetape_postpone_request(drive);
}
-static void ide_tape_io_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc,
+static int ide_tape_io_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc,
unsigned int bcount, int write)
{
if (write)
idetape_output_buffers(drive, pc, bcount);
else
idetape_input_buffers(drive, pc, bcount);
-}
-
-/*
- * This is the usual interrupt handler which will be called during a packet
- * command. We will transfer some of the data (as requested by the drive) and
- * will re-point interrupt handler to us. When data transfer is finished, we
- * will act according to the algorithm described before
- * idetape_issue_pc.
- */
-static ide_startstop_t idetape_pc_intr(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
- return ide_pc_intr(drive, tape->pc, idetape_pc_intr, IDETAPE_WAIT_CMD,
- NULL, idetape_update_buffers, idetape_retry_pc,
- ide_tape_handle_dsc, ide_tape_io_buffers);
+ return bcount;
}
/*
* Packet Command Interface
*
- * The current Packet Command is available in tape->pc, and will not change
+ * The current Packet Command is available in drive->pc, and will not change
* until we finish handling it. Each packet command is associated with a
* callback function that will be called when the command is finished.
*
* The handling will be done in three stages:
*
* 1. idetape_issue_pc will send the packet command to the drive, and will set
- * the interrupt handler to idetape_pc_intr.
+ * the interrupt handler to ide_pc_intr.
*
- * 2. On each interrupt, idetape_pc_intr will be called. This step will be
+ * 2. On each interrupt, ide_pc_intr will be called. This step will be
* repeated until the device signals us that no more interrupts will be issued.
*
* 3. ATAPI Tape media access commands have immediate status with a delayed
* again, the callback function will be called and then we will handle the next
* request.
*/
-static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
-
- return ide_transfer_pc(drive, tape->pc, idetape_pc_intr,
- IDETAPE_WAIT_CMD, NULL);
-}
static ide_startstop_t idetape_issue_pc(ide_drive_t *drive,
struct ide_atapi_pc *pc)
{
idetape_tape_t *tape = drive->driver_data;
- if (tape->pc->c[0] == REQUEST_SENSE &&
+ if (drive->pc->c[0] == REQUEST_SENSE &&
pc->c[0] == REQUEST_SENSE) {
printk(KERN_ERR "ide-tape: possible ide-tape.c bug - "
"Two request sense in serial were issued\n");
if (tape->failed_pc == NULL && pc->c[0] != REQUEST_SENSE)
tape->failed_pc = pc;
+
/* Set the current packet command */
- tape->pc = pc;
+ drive->pc = pc;
if (pc->retries > IDETAPE_MAX_PC_RETRIES ||
(pc->flags & PC_FLAG_ABORT)) {
pc->error = IDETAPE_ERROR_GENERAL;
}
tape->failed_pc = NULL;
- pc->callback(drive);
+ drive->pc_callback(drive, 0);
return ide_stopped;
}
debug_log(DBG_SENSE, "Retry #%d, cmd = %02X\n", pc->retries, pc->c[0]);
pc->retries++;
- return ide_issue_pc(drive, pc, idetape_transfer_pc,
- IDETAPE_WAIT_CMD, NULL);
+ return ide_issue_pc(drive, WAIT_TAPE_CMD, NULL);
}
/* A mode sense command is used to "sense" tape parameters. */
static void idetape_create_mode_sense_cmd(struct ide_atapi_pc *pc, u8 page_code)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = MODE_SENSE;
if (page_code != IDETAPE_BLOCK_DESCRIPTOR)
/* DBD = 1 - Don't return block descriptors */
{
ide_hwif_t *hwif = drive->hwif;
idetape_tape_t *tape = drive->driver_data;
- struct ide_atapi_pc *pc = tape->pc;
+ struct ide_atapi_pc *pc = drive->pc;
u8 stat;
stat = hwif->tp_ops->read_status(hwif);
- if (stat & SEEK_STAT) {
- if (stat & ERR_STAT) {
+ if (stat & ATA_DSC) {
+ if (stat & ATA_ERR) {
/* Error detected */
if (pc->c[0] != TEST_UNIT_READY)
printk(KERN_ERR "ide-tape: %s: I/O error, ",
tape->name);
/* Retry operation */
- idetape_retry_pc(drive);
+ ide_retry_pc(drive, tape->disk);
return ide_stopped;
}
pc->error = 0;
pc->error = IDETAPE_ERROR_GENERAL;
tape->failed_pc = NULL;
}
- pc->callback(drive);
+ drive->pc_callback(drive, 0);
return ide_stopped;
}
static void ide_tape_create_rw_cmd(idetape_tape_t *tape,
- struct ide_atapi_pc *pc, unsigned int length,
- struct idetape_bh *bh, u8 opcode)
+ struct ide_atapi_pc *pc, struct request *rq,
+ u8 opcode)
{
- idetape_init_pc(pc);
+ struct idetape_bh *bh = (struct idetape_bh *)rq->special;
+ unsigned int length = rq->current_nr_sectors;
+
+ ide_init_pc(pc);
put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]);
pc->c[1] = 1;
pc->bh = bh;
pc->b_data = bh->b_data;
pc->b_count = atomic_read(&bh->b_count);
}
+
+ memcpy(rq->cmd, pc->c, 12);
}
static ide_startstop_t idetape_do_request(ide_drive_t *drive,
struct request *postponed_rq = tape->postponed_rq;
u8 stat;
- debug_log(DBG_SENSE, "sector: %ld, nr_sectors: %ld,"
- " current_nr_sectors: %d\n",
- rq->sector, rq->nr_sectors, rq->current_nr_sectors);
+ debug_log(DBG_SENSE, "sector: %llu, nr_sectors: %lu,"
+ " current_nr_sectors: %u\n",
+ (unsigned long long)rq->sector, rq->nr_sectors,
+ rq->current_nr_sectors);
if (!blk_special_request(rq)) {
/* We do not support buffer cache originated requests. */
}
/* Retry a failed packet command */
- if (tape->failed_pc && tape->pc->c[0] == REQUEST_SENSE) {
+ if (tape->failed_pc && drive->pc->c[0] == REQUEST_SENSE) {
pc = tape->failed_pc;
goto out;
}
*/
stat = hwif->tp_ops->read_status(hwif);
- if (!drive->dsc_overlap && !(rq->cmd[0] & REQ_IDETAPE_PC2))
- set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags);
+ if ((drive->dev_flags & IDE_DFLAG_DSC_OVERLAP) == 0 &&
+ (rq->cmd[13] & REQ_IDETAPE_PC2) == 0)
+ set_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags);
- if (drive->post_reset == 1) {
- set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags);
- drive->post_reset = 0;
+ if (drive->dev_flags & IDE_DFLAG_POST_RESET) {
+ set_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags);
+ drive->dev_flags &= ~IDE_DFLAG_POST_RESET;
}
- if (!test_and_clear_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags) &&
- (stat & SEEK_STAT) == 0) {
+ if (!test_and_clear_bit(IDE_AFLAG_IGNORE_DSC, &drive->atapi_flags) &&
+ (stat & ATA_DSC) == 0) {
if (postponed_rq == NULL) {
tape->dsc_polling_start = jiffies;
tape->dsc_poll_freq = tape->best_dsc_rw_freq;
} else if (time_after(jiffies, tape->dsc_timeout)) {
printk(KERN_ERR "ide-tape: %s: DSC timeout\n",
tape->name);
- if (rq->cmd[0] & REQ_IDETAPE_PC2) {
+ if (rq->cmd[13] & REQ_IDETAPE_PC2) {
idetape_media_access_finished(drive);
return ide_stopped;
} else {
idetape_postpone_request(drive);
return ide_stopped;
}
- if (rq->cmd[0] & REQ_IDETAPE_READ) {
- pc = idetape_next_pc_storage(drive);
- ide_tape_create_rw_cmd(tape, pc, rq->current_nr_sectors,
- (struct idetape_bh *)rq->special,
- READ_6);
+ if (rq->cmd[13] & REQ_IDETAPE_READ) {
+ pc = &tape->queued_pc;
+ ide_tape_create_rw_cmd(tape, pc, rq, READ_6);
goto out;
}
- if (rq->cmd[0] & REQ_IDETAPE_WRITE) {
- pc = idetape_next_pc_storage(drive);
- ide_tape_create_rw_cmd(tape, pc, rq->current_nr_sectors,
- (struct idetape_bh *)rq->special,
- WRITE_6);
+ if (rq->cmd[13] & REQ_IDETAPE_WRITE) {
+ pc = &tape->queued_pc;
+ ide_tape_create_rw_cmd(tape, pc, rq, WRITE_6);
goto out;
}
- if (rq->cmd[0] & REQ_IDETAPE_PC1) {
+ if (rq->cmd[13] & REQ_IDETAPE_PC1) {
pc = (struct ide_atapi_pc *) rq->buffer;
- rq->cmd[0] &= ~(REQ_IDETAPE_PC1);
- rq->cmd[0] |= REQ_IDETAPE_PC2;
+ rq->cmd[13] &= ~(REQ_IDETAPE_PC1);
+ rq->cmd[13] |= REQ_IDETAPE_PC2;
goto out;
}
- if (rq->cmd[0] & REQ_IDETAPE_PC2) {
+ if (rq->cmd[13] & REQ_IDETAPE_PC2) {
idetape_media_access_finished(drive);
return ide_stopped;
}
BUG();
-out:
- if (test_bit(IDETAPE_FLAG_DRQ_INTERRUPT, &tape->flags))
- pc->flags |= PC_FLAG_DRQ_INTERRUPT;
+out:
return idetape_issue_pc(drive, pc);
}
static void idetape_create_write_filemark_cmd(ide_drive_t *drive,
struct ide_atapi_pc *pc, int write_filemark)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = WRITE_FILEMARKS;
pc->c[4] = write_filemark;
pc->flags |= PC_FLAG_WAIT_FOR_DSC;
}
-static void idetape_create_test_unit_ready_cmd(struct ide_atapi_pc *pc)
-{
- idetape_init_pc(pc);
- pc->c[0] = TEST_UNIT_READY;
-}
-
-/*
- * We add a special packet command request to the tail of the request queue, and
- * wait for it to be serviced. This is not to be called from within the request
- * handling part of the driver! We allocate here data on the stack and it is
- * valid until the request is finished. This is not the case for the bottom part
- * of the driver, where we are always leaving the functions to wait for an
- * interrupt or a timer event.
- *
- * From the bottom part of the driver, we should allocate safe memory using
- * idetape_next_pc_storage() and ide_tape_next_rq_storage(), and add the request
- * to the request list without waiting for it to be serviced! In that case, we
- * usually use idetape_queue_pc_head().
- */
-static int idetape_queue_pc_tail(ide_drive_t *drive, struct ide_atapi_pc *pc)
-{
- struct ide_tape_obj *tape = drive->driver_data;
- struct request *rq;
- int error;
-
- rq = blk_get_request(drive->queue, READ, __GFP_WAIT);
- rq->cmd_type = REQ_TYPE_SPECIAL;
- rq->cmd[0] = REQ_IDETAPE_PC1;
- rq->buffer = (char *)pc;
- error = blk_execute_rq(drive->queue, tape->disk, rq, 0);
- blk_put_request(rq);
- return error;
-}
-
-static void idetape_create_load_unload_cmd(ide_drive_t *drive,
- struct ide_atapi_pc *pc, int cmd)
-{
- idetape_init_pc(pc);
- pc->c[0] = START_STOP;
- pc->c[4] = cmd;
- pc->flags |= PC_FLAG_WAIT_FOR_DSC;
-}
-
static int idetape_wait_ready(ide_drive_t *drive, unsigned long timeout)
{
idetape_tape_t *tape = drive->driver_data;
- struct ide_atapi_pc pc;
+ struct gendisk *disk = tape->disk;
int load_attempted = 0;
/* Wait for the tape to become ready */
- set_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags);
+ set_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags);
timeout += jiffies;
while (time_before(jiffies, timeout)) {
- idetape_create_test_unit_ready_cmd(&pc);
- if (!idetape_queue_pc_tail(drive, &pc))
+ if (ide_do_test_unit_ready(drive, disk) == 0)
return 0;
if ((tape->sense_key == 2 && tape->asc == 4 && tape->ascq == 2)
|| (tape->asc == 0x3A)) {
/* no media */
if (load_attempted)
return -ENOMEDIUM;
- idetape_create_load_unload_cmd(drive, &pc,
- IDETAPE_LU_LOAD_MASK);
- idetape_queue_pc_tail(drive, &pc);
+ ide_do_start_stop(drive, disk, IDETAPE_LU_LOAD_MASK);
load_attempted = 1;
/* not about to be ready */
} else if (!(tape->sense_key == 2 && tape->asc == 4 &&
static int idetape_flush_tape_buffers(ide_drive_t *drive)
{
+ struct ide_tape_obj *tape = drive->driver_data;
struct ide_atapi_pc pc;
int rc;
idetape_create_write_filemark_cmd(drive, &pc, 0);
- rc = idetape_queue_pc_tail(drive, &pc);
+ rc = ide_queue_pc_tail(drive, tape->disk, &pc);
if (rc)
return rc;
idetape_wait_ready(drive, 60 * 5 * HZ);
static void idetape_create_read_position_cmd(struct ide_atapi_pc *pc)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = READ_POSITION;
pc->req_xfer = 20;
}
debug_log(DBG_PROCS, "Enter %s\n", __func__);
idetape_create_read_position_cmd(&pc);
- if (idetape_queue_pc_tail(drive, &pc))
+ if (ide_queue_pc_tail(drive, tape->disk, &pc))
return -1;
position = tape->first_frame;
return position;
struct ide_atapi_pc *pc,
unsigned int block, u8 partition, int skip)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = POSITION_TO_ELEMENT;
pc->c[1] = 2;
put_unaligned(cpu_to_be32(block), (unsigned int *) &pc->c[3]);
pc->flags |= PC_FLAG_WAIT_FOR_DSC;
}
-static int idetape_create_prevent_cmd(ide_drive_t *drive,
- struct ide_atapi_pc *pc, int prevent)
-{
- idetape_tape_t *tape = drive->driver_data;
-
- /* device supports locking according to capabilities page */
- if (!(tape->caps[6] & 0x01))
- return 0;
-
- idetape_init_pc(pc);
- pc->c[0] = ALLOW_MEDIUM_REMOVAL;
- pc->c[4] = prevent;
- return 1;
-}
-
static void __ide_tape_discard_merge_buffer(ide_drive_t *drive)
{
idetape_tape_t *tape = drive->driver_data;
if (tape->chrdev_dir != IDETAPE_DIR_READ)
return;
- clear_bit(IDETAPE_FLAG_FILEMARK, &tape->flags);
+ clear_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags);
tape->merge_bh_size = 0;
if (tape->merge_bh != NULL) {
ide_tape_kfree_buffer(tape);
u8 partition, int skip)
{
idetape_tape_t *tape = drive->driver_data;
+ struct gendisk *disk = tape->disk;
int retval;
struct ide_atapi_pc pc;
__ide_tape_discard_merge_buffer(drive);
idetape_wait_ready(drive, 60 * 5 * HZ);
idetape_create_locate_cmd(drive, &pc, block, partition, skip);
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_queue_pc_tail(drive, disk, &pc);
if (retval)
return (retval);
idetape_create_read_position_cmd(&pc);
- return (idetape_queue_pc_tail(drive, &pc));
+ return ide_queue_pc_tail(drive, disk, &pc);
}
static void ide_tape_discard_merge_buffer(ide_drive_t *drive,
rq = blk_get_request(drive->queue, READ, __GFP_WAIT);
rq->cmd_type = REQ_TYPE_SPECIAL;
- rq->cmd[0] = cmd;
+ rq->cmd[13] = cmd;
rq->rq_disk = tape->disk;
rq->special = (void *)bh;
rq->sector = tape->first_frame;
static void idetape_create_inquiry_cmd(struct ide_atapi_pc *pc)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = INQUIRY;
pc->c[4] = 254;
pc->req_xfer = 254;
static void idetape_create_rewind_cmd(ide_drive_t *drive,
struct ide_atapi_pc *pc)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = REZERO_UNIT;
pc->flags |= PC_FLAG_WAIT_FOR_DSC;
}
static void idetape_create_erase_cmd(struct ide_atapi_pc *pc)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = ERASE;
pc->c[1] = 1;
pc->flags |= PC_FLAG_WAIT_FOR_DSC;
static void idetape_create_space_cmd(struct ide_atapi_pc *pc, int count, u8 cmd)
{
- idetape_init_pc(pc);
+ ide_init_pc(pc);
pc->c[0] = SPACE;
put_unaligned(cpu_to_be32(count), (unsigned int *) &pc->c[1]);
pc->c[1] = cmd;
* No point in issuing this if DSC overlap isn't supported, some
* drives (Seagate STT3401A) will return an error.
*/
- if (drive->dsc_overlap) {
+ if (drive->dev_flags & IDE_DFLAG_DSC_OVERLAP) {
bytes_read = idetape_queue_rw_tail(drive,
REQ_IDETAPE_READ, 0,
tape->merge_bh);
debug_log(DBG_PROCS, "Enter %s, %d blocks\n", __func__, blocks);
/* If we are at a filemark, return a read length of 0 */
- if (test_bit(IDETAPE_FLAG_FILEMARK, &tape->flags))
+ if (test_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags))
return 0;
idetape_init_read(drive);
*/
static int idetape_rewind_tape(ide_drive_t *drive)
{
+ struct ide_tape_obj *tape = drive->driver_data;
+ struct gendisk *disk = tape->disk;
int retval;
struct ide_atapi_pc pc;
- idetape_tape_t *tape;
- tape = drive->driver_data;
debug_log(DBG_SENSE, "Enter %s\n", __func__);
idetape_create_rewind_cmd(drive, &pc);
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_queue_pc_tail(drive, disk, &pc);
if (retval)
return retval;
idetape_create_read_position_cmd(&pc);
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_queue_pc_tail(drive, disk, &pc);
if (retval)
return retval;
return 0;
int mt_count)
{
idetape_tape_t *tape = drive->driver_data;
+ struct gendisk *disk = tape->disk;
struct ide_atapi_pc pc;
int retval, count = 0;
int sprev = !!(tape->caps[4] & 0x20);
if (tape->chrdev_dir == IDETAPE_DIR_READ) {
tape->merge_bh_size = 0;
- if (test_and_clear_bit(IDETAPE_FLAG_FILEMARK, &tape->flags))
+ if (test_and_clear_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags))
++count;
ide_tape_discard_merge_buffer(drive, 0);
}
case MTBSF:
idetape_create_space_cmd(&pc, mt_count - count,
IDETAPE_SPACE_OVER_FILEMARK);
- return idetape_queue_pc_tail(drive, &pc);
+ return ide_queue_pc_tail(drive, disk, &pc);
case MTFSFM:
case MTBSFM:
if (!sprev)
static ssize_t idetape_chrdev_read(struct file *file, char __user *buf,
size_t count, loff_t *ppos)
{
- struct ide_tape_obj *tape = ide_tape_f(file);
+ struct ide_tape_obj *tape = file->private_data;
ide_drive_t *drive = tape->drive;
ssize_t bytes_read, temp, actually_read = 0, rc;
ssize_t ret = 0;
debug_log(DBG_CHRDEV, "Enter %s, count %Zd\n", __func__, count);
if (tape->chrdev_dir != IDETAPE_DIR_READ) {
- if (test_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags))
+ if (test_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags))
if (count > tape->blk_size &&
(count % tape->blk_size) == 0)
tape->user_bs_factor = count / tape->blk_size;
tape->merge_bh_size = bytes_read-temp;
}
finish:
- if (!actually_read && test_bit(IDETAPE_FLAG_FILEMARK, &tape->flags)) {
+ if (!actually_read && test_bit(IDE_AFLAG_FILEMARK, &drive->atapi_flags)) {
debug_log(DBG_SENSE, "%s: spacing over filemark\n", tape->name);
idetape_space_over_filemarks(drive, MTFSF, 1);
static ssize_t idetape_chrdev_write(struct file *file, const char __user *buf,
size_t count, loff_t *ppos)
{
- struct ide_tape_obj *tape = ide_tape_f(file);
+ struct ide_tape_obj *tape = file->private_data;
ide_drive_t *drive = tape->drive;
ssize_t actually_written = 0;
ssize_t ret = 0;
* point in issuing this if DSC overlap isn't supported, some
* drives (Seagate STT3401A) will return an error.
*/
- if (drive->dsc_overlap) {
+ if (drive->dev_flags & IDE_DFLAG_DSC_OVERLAP) {
ssize_t retval = idetape_queue_rw_tail(drive,
REQ_IDETAPE_WRITE, 0,
tape->merge_bh);
static int idetape_write_filemark(ide_drive_t *drive)
{
+ struct ide_tape_obj *tape = drive->driver_data;
struct ide_atapi_pc pc;
/* Write a filemark */
idetape_create_write_filemark_cmd(drive, &pc, 1);
- if (idetape_queue_pc_tail(drive, &pc)) {
+ if (ide_queue_pc_tail(drive, tape->disk, &pc)) {
printk(KERN_ERR "ide-tape: Couldn't write a filemark\n");
return -EIO;
}
static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count)
{
idetape_tape_t *tape = drive->driver_data;
+ struct gendisk *disk = tape->disk;
struct ide_atapi_pc pc;
int i, retval;
return 0;
case MTLOAD:
ide_tape_discard_merge_buffer(drive, 0);
- idetape_create_load_unload_cmd(drive, &pc,
- IDETAPE_LU_LOAD_MASK);
- return idetape_queue_pc_tail(drive, &pc);
+ return ide_do_start_stop(drive, disk, IDETAPE_LU_LOAD_MASK);
case MTUNLOAD:
case MTOFFL:
/*
* attempting to eject.
*/
if (tape->door_locked) {
- if (idetape_create_prevent_cmd(drive, &pc, 0))
- if (!idetape_queue_pc_tail(drive, &pc))
- tape->door_locked = DOOR_UNLOCKED;
+ if (!ide_set_media_lock(drive, disk, 0))
+ tape->door_locked = DOOR_UNLOCKED;
}
ide_tape_discard_merge_buffer(drive, 0);
- idetape_create_load_unload_cmd(drive, &pc,
- !IDETAPE_LU_LOAD_MASK);
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_do_start_stop(drive, disk, !IDETAPE_LU_LOAD_MASK);
if (!retval)
- clear_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags);
+ clear_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags);
return retval;
case MTNOP:
ide_tape_discard_merge_buffer(drive, 0);
return idetape_flush_tape_buffers(drive);
case MTRETEN:
ide_tape_discard_merge_buffer(drive, 0);
- idetape_create_load_unload_cmd(drive, &pc,
+ return ide_do_start_stop(drive, disk,
IDETAPE_LU_RETENSION_MASK | IDETAPE_LU_LOAD_MASK);
- return idetape_queue_pc_tail(drive, &pc);
case MTEOM:
idetape_create_space_cmd(&pc, 0, IDETAPE_SPACE_TO_EOD);
- return idetape_queue_pc_tail(drive, &pc);
+ return ide_queue_pc_tail(drive, disk, &pc);
case MTERASE:
(void)idetape_rewind_tape(drive);
idetape_create_erase_cmd(&pc);
- return idetape_queue_pc_tail(drive, &pc);
+ return ide_queue_pc_tail(drive, disk, &pc);
case MTSETBLK:
if (mt_count) {
if (mt_count < tape->blk_size ||
mt_count % tape->blk_size)
return -EIO;
tape->user_bs_factor = mt_count / tape->blk_size;
- clear_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags);
+ clear_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags);
} else
- set_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags);
+ set_bit(IDE_AFLAG_DETECT_BS, &drive->atapi_flags);
return 0;
case MTSEEK:
ide_tape_discard_merge_buffer(drive, 0);
case MTFSR:
case MTBSR:
case MTLOCK:
- if (!idetape_create_prevent_cmd(drive, &pc, 1))
- return 0;
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_set_media_lock(drive, disk, 1);
if (retval)
return retval;
tape->door_locked = DOOR_EXPLICITLY_LOCKED;
return 0;
case MTUNLOCK:
- if (!idetape_create_prevent_cmd(drive, &pc, 0))
- return 0;
- retval = idetape_queue_pc_tail(drive, &pc);
+ retval = ide_set_media_lock(drive, disk, 0);
if (retval)
return retval;
tape->door_locked = DOOR_UNLOCKED;
static int idetape_chrdev_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
- struct ide_tape_obj *tape = ide_tape_f(file);
+ struct ide_tape_obj *tape = file->private_data;
ide_drive_t *drive = tape->drive;
struct mtop mtop;
struct mtget mtget;
struct ide_atapi_pc pc;
idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR);
- if (idetape_queue_pc_tail(drive, &pc)) {
+ if (ide_queue_pc_tail(drive, tape->disk, &pc)) {
printk(KERN_ERR "ide-tape: Can't get block descriptor\n");
if (tape->blk_size == 0) {
printk(KERN_WARNING "ide-tape: Cannot deal with zero "
unsigned int minor = iminor(inode), i = minor & ~0xc0;
ide_drive_t *drive;
idetape_tape_t *tape;
- struct ide_atapi_pc pc;
int retval;
if (i >= MAX_HWIFS * MAX_DRIVES)
filp->private_data = tape;
- if (test_and_set_bit(IDETAPE_FLAG_BUSY, &tape->flags)) {
+ if (test_and_set_bit(IDE_AFLAG_BUSY, &drive->atapi_flags)) {
retval = -EBUSY;
goto out_put_tape;
}
retval = idetape_wait_ready(drive, 60 * HZ);
if (retval) {
- clear_bit(IDETAPE_FLAG_BUSY, &tape->flags);
+ clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags);
printk(KERN_ERR "ide-tape: %s: drive not ready\n", tape->name);
goto out_put_tape;
}
idetape_read_position(drive);
- if (!test_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags))
+ if (!test_bit(IDE_AFLAG_ADDRESS_VALID, &drive->atapi_flags))
(void)idetape_rewind_tape(drive);
/* Read block size and write protect status from drive. */
if (tape->write_prot) {
if ((filp->f_flags & O_ACCMODE) == O_WRONLY ||
(filp->f_flags & O_ACCMODE) == O_RDWR) {
- clear_bit(IDETAPE_FLAG_BUSY, &tape->flags);
+ clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags);
retval = -EROFS;
goto out_put_tape;
}
/* Lock the tape drive door so user can't eject. */
if (tape->chrdev_dir == IDETAPE_DIR_NONE) {
- if (idetape_create_prevent_cmd(drive, &pc, 1)) {
- if (!idetape_queue_pc_tail(drive, &pc)) {
- if (tape->door_locked != DOOR_EXPLICITLY_LOCKED)
- tape->door_locked = DOOR_LOCKED;
- }
+ if (!ide_set_media_lock(drive, tape->disk, 1)) {
+ if (tape->door_locked != DOOR_EXPLICITLY_LOCKED)
+ tape->door_locked = DOOR_LOCKED;
}
}
unlock_kernel();
static int idetape_chrdev_release(struct inode *inode, struct file *filp)
{
- struct ide_tape_obj *tape = ide_tape_f(filp);
+ struct ide_tape_obj *tape = filp->private_data;
ide_drive_t *drive = tape->drive;
- struct ide_atapi_pc pc;
unsigned int minor = iminor(inode);
lock_kernel();
ide_tape_discard_merge_buffer(drive, 1);
}
- if (minor < 128 && test_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags))
+ if (minor < 128 && test_bit(IDE_AFLAG_MEDIUM_PRESENT, &drive->atapi_flags))
(void) idetape_rewind_tape(drive);
if (tape->chrdev_dir == IDETAPE_DIR_NONE) {
if (tape->door_locked == DOOR_LOCKED) {
- if (idetape_create_prevent_cmd(drive, &pc, 0)) {
- if (!idetape_queue_pc_tail(drive, &pc))
- tape->door_locked = DOOR_UNLOCKED;
- }
+ if (!ide_set_media_lock(drive, tape->disk, 0))
+ tape->door_locked = DOOR_UNLOCKED;
}
}
- clear_bit(IDETAPE_FLAG_BUSY, &tape->flags);
+ clear_bit(IDE_AFLAG_BUSY, &drive->atapi_flags);
ide_tape_put(tape);
unlock_kernel();
return 0;
}
-/*
- * check the contents of the ATAPI IDENTIFY command results. We return:
- *
- * 1 - If the tape can be supported by us, based on the information we have so
- * far.
- *
- * 0 - If this tape driver is not currently supported by us.
- */
-static int idetape_identify_device(ide_drive_t *drive)
-{
- u8 gcw[2], protocol, device_type, removable, packet_size;
-
- if (drive->id_read == 0)
- return 1;
-
- *((unsigned short *) &gcw) = drive->id->config;
-
- protocol = (gcw[1] & 0xC0) >> 6;
- device_type = gcw[1] & 0x1F;
- removable = !!(gcw[0] & 0x80);
- packet_size = gcw[0] & 0x3;
-
- /* Check that we can support this device */
- if (protocol != 2)
- printk(KERN_ERR "ide-tape: Protocol (0x%02x) is not ATAPI\n",
- protocol);
- else if (device_type != 1)
- printk(KERN_ERR "ide-tape: Device type (0x%02x) is not set "
- "to tape\n", device_type);
- else if (!removable)
- printk(KERN_ERR "ide-tape: The removable flag is not set\n");
- else if (packet_size != 0) {
- printk(KERN_ERR "ide-tape: Packet size (0x%02x) is not 12"
- " bytes\n", packet_size);
- } else
- return 1;
- return 0;
-}
-
static void idetape_get_inquiry_results(ide_drive_t *drive)
{
idetape_tape_t *tape = drive->driver_data;
struct ide_atapi_pc pc;
- char fw_rev[6], vendor_id[10], product_id[18];
+ char fw_rev[4], vendor_id[8], product_id[16];
idetape_create_inquiry_cmd(&pc);
- if (idetape_queue_pc_tail(drive, &pc)) {
+ if (ide_queue_pc_tail(drive, tape->disk, &pc)) {
printk(KERN_ERR "ide-tape: %s: can't get INQUIRY results\n",
tape->name);
return;
memcpy(product_id, &pc.buf[16], 16);
memcpy(fw_rev, &pc.buf[32], 4);
- ide_fixstring(vendor_id, 10, 0);
- ide_fixstring(product_id, 18, 0);
- ide_fixstring(fw_rev, 6, 0);
+ ide_fixstring(vendor_id, 8, 0);
+ ide_fixstring(product_id, 16, 0);
+ ide_fixstring(fw_rev, 4, 0);
- printk(KERN_INFO "ide-tape: %s <-> %s: %s %s rev %s\n",
+ printk(KERN_INFO "ide-tape: %s <-> %s: %.8s %.16s rev %.4s\n",
drive->name, tape->name, vendor_id, product_id, fw_rev);
}
u8 speed, max_speed;
idetape_create_mode_sense_cmd(&pc, IDETAPE_CAPABILITIES_PAGE);
- if (idetape_queue_pc_tail(drive, &pc)) {
+ if (ide_queue_pc_tail(drive, tape->disk, &pc)) {
printk(KERN_ERR "ide-tape: Can't get tape parameters - assuming"
" some default values\n");
tape->blk_size = 512;
caps = pc.buf + 4 + pc.buf[3];
/* convert to host order and save for later use */
- speed = be16_to_cpu(*(u16 *)&caps[14]);
- max_speed = be16_to_cpu(*(u16 *)&caps[8]);
+ speed = be16_to_cpup((__be16 *)&caps[14]);
+ max_speed = be16_to_cpup((__be16 *)&caps[8]);
- put_unaligned(max_speed, (u16 *)&caps[8]);
- put_unaligned(be16_to_cpu(*(u16 *)&caps[12]), (u16 *)&caps[12]);
- put_unaligned(speed, (u16 *)&caps[14]);
- put_unaligned(be16_to_cpu(*(u16 *)&caps[16]), (u16 *)&caps[16]);
+ *(u16 *)&caps[8] = max_speed;
+ *(u16 *)&caps[12] = be16_to_cpup((__be16 *)&caps[12]);
+ *(u16 *)&caps[14] = speed;
+ *(u16 *)&caps[16] = be16_to_cpup((__be16 *)&caps[16]);
if (!speed) {
printk(KERN_INFO "ide-tape: %s: invalid tape speed "
"(assuming 650KB/sec)\n", drive->name);
- put_unaligned(650, (u16 *)&caps[14]);
+ *(u16 *)&caps[14] = 650;
}
if (!max_speed) {
printk(KERN_INFO "ide-tape: %s: invalid max_speed "
"(assuming 650KB/sec)\n", drive->name);
- put_unaligned(650, (u16 *)&caps[8]);
+ *(u16 *)&caps[8] = 650;
}
memcpy(&tape->caps, caps, 20);
+
+ /* device lacks locking support according to capabilities page */
+ if ((caps[6] & 1) == 0)
+ drive->dev_flags &= ~IDE_DFLAG_DOORLOCKING;
+
if (caps[7] & 0x02)
tape->blk_size = 512;
else if (caps[7] & 0x04)
}
#ifdef CONFIG_IDE_PROC_FS
-static void idetape_add_settings(ide_drive_t *drive)
-{
- idetape_tape_t *tape = drive->driver_data;
-
- ide_add_setting(drive, "buffer", SETTING_READ, TYPE_SHORT, 0, 0xffff,
- 1, 2, (u16 *)&tape->caps[16], NULL);
- ide_add_setting(drive, "speed", SETTING_READ, TYPE_SHORT, 0, 0xffff,
- 1, 1, (u16 *)&tape->caps[14], NULL);
- ide_add_setting(drive, "buffer_size", SETTING_READ, TYPE_INT, 0, 0xffff,
- 1, 1024, &tape->buffer_size, NULL);
- ide_add_setting(drive, "tdsc", SETTING_RW, TYPE_INT, IDETAPE_DSC_RW_MIN,
- IDETAPE_DSC_RW_MAX, 1000, HZ, &tape->best_dsc_rw_freq,
- NULL);
- ide_add_setting(drive, "dsc_overlap", SETTING_RW, TYPE_BYTE, 0, 1, 1,
- 1, &drive->dsc_overlap, NULL);
- ide_add_setting(drive, "avg_speed", SETTING_READ, TYPE_INT, 0, 0xffff,
- 1, 1, &tape->avg_speed, NULL);
- ide_add_setting(drive, "debug_mask", SETTING_RW, TYPE_INT, 0, 0xffff, 1,
- 1, &tape->debug_mask, NULL);
-}
-#else
-static inline void idetape_add_settings(ide_drive_t *drive) { ; }
+#define ide_tape_devset_get(name, field) \
+static int get_##name(ide_drive_t *drive) \
+{ \
+ idetape_tape_t *tape = drive->driver_data; \
+ return tape->field; \
+}
+
+#define ide_tape_devset_set(name, field) \
+static int set_##name(ide_drive_t *drive, int arg) \
+{ \
+ idetape_tape_t *tape = drive->driver_data; \
+ tape->field = arg; \
+ return 0; \
+}
+
+#define ide_tape_devset_rw_field(_name, _field) \
+ide_tape_devset_get(_name, _field) \
+ide_tape_devset_set(_name, _field) \
+IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
+
+#define ide_tape_devset_r_field(_name, _field) \
+ide_tape_devset_get(_name, _field) \
+IDE_DEVSET(_name, 0, get_##_name, NULL)
+
+static int mulf_tdsc(ide_drive_t *drive) { return 1000; }
+static int divf_tdsc(ide_drive_t *drive) { return HZ; }
+static int divf_buffer(ide_drive_t *drive) { return 2; }
+static int divf_buffer_size(ide_drive_t *drive) { return 1024; }
+
+ide_devset_rw_flag(dsc_overlap, IDE_DFLAG_DSC_OVERLAP);
+
+ide_tape_devset_rw_field(debug_mask, debug_mask);
+ide_tape_devset_rw_field(tdsc, best_dsc_rw_freq);
+
+ide_tape_devset_r_field(avg_speed, avg_speed);
+ide_tape_devset_r_field(speed, caps[14]);
+ide_tape_devset_r_field(buffer, caps[16]);
+ide_tape_devset_r_field(buffer_size, buffer_size);
+
+static const struct ide_proc_devset idetape_settings[] = {
+ __IDE_PROC_DEVSET(avg_speed, 0, 0xffff, NULL, NULL),
+ __IDE_PROC_DEVSET(buffer, 0, 0xffff, NULL, divf_buffer),
+ __IDE_PROC_DEVSET(buffer_size, 0, 0xffff, NULL, divf_buffer_size),
+ __IDE_PROC_DEVSET(debug_mask, 0, 0xffff, NULL, NULL),
+ __IDE_PROC_DEVSET(dsc_overlap, 0, 1, NULL, NULL),
+ __IDE_PROC_DEVSET(speed, 0, 0xffff, NULL, NULL),
+ __IDE_PROC_DEVSET(tdsc, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX,
+ mulf_tdsc, divf_tdsc),
+ { 0 },
+};
#endif
/*
unsigned long t;
int speed;
int buffer_size;
- u8 gcw[2];
u16 *ctl = (u16 *)&tape->caps[12];
+ drive->pc_callback = ide_tape_callback;
+ drive->pc_update_buffers = idetape_update_buffers;
+ drive->pc_io_buffers = ide_tape_io_buffers;
+
spin_lock_init(&tape->lock);
- drive->dsc_overlap = 1;
+
+ drive->dev_flags |= IDE_DFLAG_DSC_OVERLAP;
+
if (drive->hwif->host_flags & IDE_HFLAG_NO_DSC) {
printk(KERN_INFO "ide-tape: %s: disabling DSC overlap\n",
tape->name);
- drive->dsc_overlap = 0;
+ drive->dev_flags &= ~IDE_DFLAG_DSC_OVERLAP;
}
+
/* Seagate Travan drives do not support DSC overlap. */
- if (strstr(drive->id->model, "Seagate STT3401"))
- drive->dsc_overlap = 0;
+ if (strstr((char *)&drive->id[ATA_ID_PROD], "Seagate STT3401"))
+ drive->dev_flags &= ~IDE_DFLAG_DSC_OVERLAP;
+
tape->minor = minor;
tape->name[0] = 'h';
tape->name[1] = 't';
tape->name[2] = '0' + minor;
tape->chrdev_dir = IDETAPE_DIR_NONE;
- tape->pc = tape->pc_stack;
- *((unsigned short *) &gcw) = drive->id->config;
-
- /* Command packet DRQ type */
- if (((gcw[0] & 0x60) >> 5) == 1)
- set_bit(IDETAPE_FLAG_DRQ_INTERRUPT, &tape->flags);
idetape_get_inquiry_results(drive);
idetape_get_mode_sense_results(drive);
(*(u16 *)&tape->caps[16] * 512) / tape->buffer_size,
tape->buffer_size / 1024,
tape->best_dsc_rw_freq * 1000 / HZ,
- drive->using_dma ? ", DMA":"");
+ (drive->dev_flags & IDE_DFLAG_USING_DMA) ? ", DMA" : "");
- idetape_add_settings(drive);
+ ide_proc_register_driver(drive, tape->driver);
}
static void ide_tape_remove(ide_drive_t *drive)
static void ide_tape_release(struct kref *kref)
{
- struct ide_tape_obj *tape = to_ide_tape(kref);
+ struct ide_tape_obj *tape = to_ide_drv(kref, ide_tape_obj);
ide_drive_t *drive = tape->drive;
struct gendisk *g = tape->disk;
BUG_ON(tape->merge_bh_size);
- drive->dsc_overlap = 0;
+ drive->dev_flags &= ~IDE_DFLAG_DSC_OVERLAP;
drive->driver_data = NULL;
device_destroy(idetape_sysfs_class, MKDEV(IDETAPE_MAJOR, tape->minor));
device_destroy(idetape_sysfs_class,
{ "name", S_IFREG|S_IRUGO, proc_idetape_read_name, NULL },
{ NULL, 0, NULL, NULL }
};
+
+static ide_proc_entry_t *ide_tape_proc_entries(ide_drive_t *drive)
+{
+ return idetape_proc;
+}
+
+static const struct ide_proc_devset *ide_tape_proc_devsets(ide_drive_t *drive)
+{
+ return idetape_settings;
+}
#endif
static int ide_tape_probe(ide_drive_t *);
.probe = ide_tape_probe,
.remove = ide_tape_remove,
.version = IDETAPE_VERSION,
- .media = ide_tape,
- .supports_dsc_overlap = 1,
.do_request = idetape_do_request,
.end_request = idetape_end_request,
.error = __ide_error,
#ifdef CONFIG_IDE_PROC_FS
- .proc = idetape_proc,
+ .proc_entries = ide_tape_proc_entries,
+ .proc_devsets = ide_tape_proc_devsets,
#endif
};
.release = idetape_chrdev_release,
};
-static int idetape_open(struct inode *inode, struct file *filp)
+static int idetape_open(struct block_device *bdev, fmode_t mode)
{
- struct gendisk *disk = inode->i_bdev->bd_disk;
- struct ide_tape_obj *tape;
+ struct ide_tape_obj *tape = ide_tape_get(bdev->bd_disk);
- tape = ide_tape_get(disk);
if (!tape)
return -ENXIO;
return 0;
}
-static int idetape_release(struct inode *inode, struct file *filp)
+static int idetape_release(struct gendisk *disk, fmode_t mode)
{
- struct gendisk *disk = inode->i_bdev->bd_disk;
- struct ide_tape_obj *tape = ide_tape_g(disk);
+ struct ide_tape_obj *tape = ide_drv_g(disk, ide_tape_obj);
ide_tape_put(tape);
-
return 0;
}
-static int idetape_ioctl(struct inode *inode, struct file *file,
+static int idetape_ioctl(struct block_device *bdev, fmode_t mode,
unsigned int cmd, unsigned long arg)
{
- struct block_device *bdev = inode->i_bdev;
- struct ide_tape_obj *tape = ide_tape_g(bdev->bd_disk);
+ struct ide_tape_obj *tape = ide_drv_g(bdev->bd_disk, ide_tape_obj);
ide_drive_t *drive = tape->drive;
- int err = generic_ide_ioctl(drive, file, bdev, cmd, arg);
+ int err = generic_ide_ioctl(drive, bdev, cmd, arg);
if (err == -EINVAL)
err = idetape_blkdev_ioctl(drive, cmd, arg);
return err;
.owner = THIS_MODULE,
.open = idetape_open,
.release = idetape_release,
- .ioctl = idetape_ioctl,
+ .locked_ioctl = idetape_ioctl,
};
static int ide_tape_probe(ide_drive_t *drive)
if (!strstr("ide-tape", drive->driver_req))
goto failed;
- if (!drive->present)
- goto failed;
+
if (drive->media != ide_tape)
goto failed;
- if (!idetape_identify_device(drive)) {
+
+ if ((drive->dev_flags & IDE_DFLAG_ID_READ) &&
+ ide_check_atapi_device(drive, DRV_NAME) == 0) {
printk(KERN_ERR "ide-tape: %s: not supported by this version of"
" the driver\n", drive->name);
goto failed;
ide_init_disk(g, drive);
- ide_proc_register_driver(drive, &idetape_driver);
-
kref_init(&tape->kref);
tape->drive = drive;
idetape_setup(drive, tape, minor);
- device_create_drvdata(idetape_sysfs_class, &drive->gendev,
- MKDEV(IDETAPE_MAJOR, minor), NULL,
- "%s", tape->name);
- device_create_drvdata(idetape_sysfs_class, &drive->gendev,
- MKDEV(IDETAPE_MAJOR, minor + 128), NULL,
- "n%s", tape->name);
+ device_create(idetape_sysfs_class, &drive->gendev,
+ MKDEV(IDETAPE_MAJOR, minor), NULL, "%s", tape->name);
+ device_create(idetape_sysfs_class, &drive->gendev,
+ MKDEV(IDETAPE_MAJOR, minor + 128), NULL,
+ "n%s", tape->name);
g->fops = &idetape_block_ops;
ide_register_region(g);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff