/*
- * linux/drivers/ide/ide-floppy.c Version 0.99 Feb 24 2002
- *
- * Copyright (C) 1996 - 1999 Gadi Oxman <gadio@netvision.net.il>
- * Copyright (C) 2000 - 2002 Paul Bristow <paul@paulbristow.net>
- */
-
-/*
* IDE ATAPI floppy driver.
*
- * The driver currently doesn't have any fancy features, just the bare
- * minimum read/write support.
+ * Copyright (C) 1996-1999 Gadi Oxman <gadio@netvision.net.il>
+ * Copyright (C) 2000-2002 Paul Bristow <paul@paulbristow.net>
+ * Copyright (C) 2005 Bartlomiej Zolnierkiewicz
*
* This driver supports the following IDE floppy drives:
*
* Iomega Zip 100/250
* Iomega PC Card Clik!/PocketZip
*
- * Many thanks to Lode Leroy <Lode.Leroy@www.ibase.be>, who tested so many
- * ALPHA patches to this driver on an EASYSTOR LS-120 ATAPI floppy drive.
- *
- * Ver 0.1 Oct 17 96 Initial test version, mostly based on ide-tape.c.
- * Ver 0.2 Oct 31 96 Minor changes.
- * Ver 0.3 Dec 2 96 Fixed error recovery bug.
- * Ver 0.4 Jan 26 97 Add support for the HDIO_GETGEO ioctl.
- * Ver 0.5 Feb 21 97 Add partitions support.
- * Use the minimum of the LBA and CHS capacities.
- * Avoid hwgroup->rq == NULL on the last irq.
- * Fix potential null dereferencing with DEBUG_LOG.
- * Ver 0.8 Dec 7 97 Increase irq timeout from 10 to 50 seconds.
- * Add media write-protect detection.
- * Issue START command only if TEST UNIT READY fails.
- * Add work-around for IOMEGA ZIP revision 21.D.
- * Remove idefloppy_get_capabilities().
- * Ver 0.9 Jul 4 99 Fix a bug which might have caused the number of
- * bytes requested on each interrupt to be zero.
- * Thanks to <shanos@es.co.nz> for pointing this out.
- * Ver 0.9.sv Jan 6 01 Sam Varshavchik <mrsam@courier-mta.com>
- * Implement low level formatting. Reimplemented
- * IDEFLOPPY_CAPABILITIES_PAGE, since we need the srfp
- * bit. My LS-120 drive barfs on
- * IDEFLOPPY_CAPABILITIES_PAGE, but maybe it's just me.
- * Compromise by not reporting a failure to get this
- * mode page. Implemented four IOCTLs in order to
- * implement formatting. IOCTls begin with 0x4600,
- * 0x46 is 'F' as in Format.
- * Jan 9 01 Userland option to select format verify.
- * Added PC_SUPPRESS_ERROR flag - some idefloppy drives
- * do not implement IDEFLOPPY_CAPABILITIES_PAGE, and
- * return a sense error. Suppress error reporting in
- * this particular case in order to avoid spurious
- * errors in syslog. The culprit is
- * idefloppy_get_capability_page(), so move it to
- * idefloppy_begin_format() so that it's not used
- * unless absolutely necessary.
- * If drive does not support format progress indication
- * monitor the dsc bit in the status register.
- * Also, O_NDELAY on open will allow the device to be
- * opened without a disk available. This can be used to
- * open an unformatted disk, or get the device capacity.
- * Ver 0.91 Dec 11 99 Added IOMEGA Clik! drive support by
- * <paul@paulbristow.net>
- * Ver 0.92 Oct 22 00 Paul Bristow became official maintainer for this
- * driver. Included Powerbook internal zip kludge.
- * Ver 0.93 Oct 24 00 Fixed bugs for Clik! drive
- * no disk on insert and disk change now works
- * Ver 0.94 Oct 27 00 Tidied up to remove strstr(Clik) everywhere
- * Ver 0.95 Nov 7 00 Brought across to kernel 2.4
- * Ver 0.96 Jan 7 01 Actually in line with release version of 2.4.0
- * including set_bit patch from Rusty Russell
- * Ver 0.97 Jul 22 01 Merge 0.91-0.96 onto 0.9.sv for ac series
- * Ver 0.97.sv Aug 3 01 Backported from 2.4.7-ac3
- * Ver 0.98 Oct 26 01 Split idefloppy_transfer_pc into two pieces to
- * fix a lost interrupt problem. It appears the busy
- * bit was being deasserted by my IOMEGA ATAPI ZIP 100
- * drive before the drive was actually ready.
- * Ver 0.98a Oct 29 01 Expose delay value so we can play.
- * Ver 0.99 Feb 24 02 Remove duplicate code, modify clik! detection code
- * to support new PocketZip drives
+ * For a historical changelog see
+ * Documentation/ide/ChangeLog.ide-floppy.1996-2002
*/
-#define IDEFLOPPY_VERSION "0.99.newide"
+#define IDEFLOPPY_VERSION "1.00"
-#include <linux/config.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/string.h>
#include <linux/cdrom.h>
#include <linux/ide.h>
#include <linux/bitops.h>
+#include <linux/mutex.h>
+
+#include <scsi/scsi_ioctl.h>
#include <asm/byteorder.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/irq.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#include <asm/unaligned.h>
-/*
- * The following are used to debug the driver.
- */
+/* define to see debug info */
#define IDEFLOPPY_DEBUG_LOG 0
-#define IDEFLOPPY_DEBUG_INFO 0
-#define IDEFLOPPY_DEBUG_BUGS 1
/* #define IDEFLOPPY_DEBUG(fmt, args...) printk(KERN_INFO fmt, ## args) */
-#define IDEFLOPPY_DEBUG( fmt, args... )
+#define IDEFLOPPY_DEBUG(fmt, args...)
#if IDEFLOPPY_DEBUG_LOG
-#define debug_log printk
+#define debug_log(fmt, args...) \
+ printk(KERN_INFO "ide-floppy: " fmt, ## args)
#else
-#define debug_log(fmt, args... ) do {} while(0)
+#define debug_log(fmt, args...) do {} while (0)
#endif
-/*
- * Some drives require a longer irq timeout.
- */
+/* Some drives require a longer irq timeout. */
#define IDEFLOPPY_WAIT_CMD (5 * WAIT_CMD)
/*
- * After each failed packet command we issue a request sense command
- * and retry the packet command IDEFLOPPY_MAX_PC_RETRIES times.
+ * After each failed packet command we issue a request sense command and retry
+ * the packet command IDEFLOPPY_MAX_PC_RETRIES times.
*/
#define IDEFLOPPY_MAX_PC_RETRIES 3
/*
- * With each packet command, we allocate a buffer of
- * IDEFLOPPY_PC_BUFFER_SIZE bytes.
+ * With each packet command, we allocate a buffer of IDEFLOPPY_PC_BUFFER_SIZE
+ * bytes.
*/
#define IDEFLOPPY_PC_BUFFER_SIZE 256
/*
- * In various places in the driver, we need to allocate storage
- * for packet commands and requests, which will remain valid while
- * we leave the driver to wait for an interrupt or a timeout event.
+ * In various places in the driver, we need to allocate storage for packet
+ * commands and requests, which will remain valid while we leave the driver to
+ * wait for an interrupt or a timeout event.
*/
#define IDEFLOPPY_PC_STACK (10 + IDEFLOPPY_MAX_PC_RETRIES)
-/*
- * Our view of a packet command.
- */
-typedef struct idefloppy_packet_command_s {
- u8 c[12]; /* Actual packet bytes */
- int retries; /* On each retry, we increment retries */
- int error; /* Error code */
- int request_transfer; /* Bytes to transfer */
- int actually_transferred; /* Bytes actually transferred */
- int buffer_size; /* Size of our data buffer */
- int b_count; /* Missing/Available data on the current buffer */
- struct request *rq; /* The corresponding request */
- u8 *buffer; /* Data buffer */
- u8 *current_position; /* Pointer into the above buffer */
- void (*callback) (ide_drive_t *); /* Called when this packet command is completed */
- u8 pc_buffer[IDEFLOPPY_PC_BUFFER_SIZE]; /* Temporary buffer */
- unsigned long flags; /* Status/Action bit flags: long for set_bit */
-} idefloppy_pc_t;
-
-/*
- * Packet command flag bits.
- */
-#define PC_ABORT 0 /* Set when an error is considered normal - We won't retry */
-#define PC_DMA_RECOMMENDED 2 /* 1 when we prefer to use DMA if possible */
-#define PC_DMA_IN_PROGRESS 3 /* 1 while DMA in progress */
-#define PC_DMA_ERROR 4 /* 1 when encountered problem during DMA */
-#define PC_WRITING 5 /* Data direction */
-
-#define PC_SUPPRESS_ERROR 6 /* Suppress error reporting */
-
-/*
- * Removable Block Access Capabilities Page
- */
-typedef struct {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned page_code :6; /* Page code - Should be 0x1b */
- unsigned reserved1_6 :1; /* Reserved */
- unsigned ps :1; /* Should be 0 */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned ps :1; /* Should be 0 */
- unsigned reserved1_6 :1; /* Reserved */
- unsigned page_code :6; /* Page code - Should be 0x1b */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 page_length; /* Page Length - Should be 0xa */
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned reserved2 :6;
- unsigned srfp :1; /* Supports reporting progress of format */
- unsigned sflp :1; /* System floppy type device */
- unsigned tlun :3; /* Total logical units supported by the device */
- unsigned reserved3 :3;
- unsigned sml :1; /* Single / Multiple lun supported */
- unsigned ncd :1; /* Non cd optical device */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned sflp :1; /* System floppy type device */
- unsigned srfp :1; /* Supports reporting progress of format */
- unsigned reserved2 :6;
- unsigned ncd :1; /* Non cd optical device */
- unsigned sml :1; /* Single / Multiple lun supported */
- unsigned reserved3 :3;
- unsigned tlun :3; /* Total logical units supported by the device */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 reserved[8];
-} idefloppy_capabilities_page_t;
-
-/*
- * Flexible disk page.
- */
-typedef struct {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned page_code :6; /* Page code - Should be 0x5 */
- unsigned reserved1_6 :1; /* Reserved */
- unsigned ps :1; /* The device is capable of saving the page */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned ps :1; /* The device is capable of saving the page */
- unsigned reserved1_6 :1; /* Reserved */
- unsigned page_code :6; /* Page code - Should be 0x5 */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 page_length; /* Page Length - Should be 0x1e */
- u16 transfer_rate; /* In kilobits per second */
- u8 heads, sectors; /* Number of heads, Number of sectors per track */
- u16 sector_size; /* Byes per sector */
- u16 cyls; /* Number of cylinders */
- u8 reserved10[10];
- u8 motor_delay; /* Motor off delay */
- u8 reserved21[7];
- u16 rpm; /* Rotations per minute */
- u8 reserved30[2];
-} idefloppy_flexible_disk_page_t;
-
-/*
- * Format capacity
- */
-typedef struct {
- u8 reserved[3];
- u8 length; /* Length of the following descriptors in bytes */
-} idefloppy_capacity_header_t;
-
-typedef struct {
- u32 blocks; /* Number of blocks */
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned dc :2; /* Descriptor Code */
- unsigned reserved :6;
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned reserved :6;
- unsigned dc :2; /* Descriptor Code */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 length_msb; /* Block Length (MSB)*/
- u16 length; /* Block Length */
-} idefloppy_capacity_descriptor_t;
-
+/* format capacities descriptor codes */
#define CAPACITY_INVALID 0x00
#define CAPACITY_UNFORMATTED 0x01
#define CAPACITY_CURRENT 0x02
#define CAPACITY_NO_CARTRIDGE 0x03
/*
- * Most of our global data which we need to save even as we leave the
- * driver due to an interrupt or a timer event is stored in a variable
- * of type idefloppy_floppy_t, defined below.
+ * Most of our global data which we need to save even as we leave the driver
+ * due to an interrupt or a timer event is stored in a variable of type
+ * idefloppy_floppy_t, defined below.
*/
typedef struct ide_floppy_obj {
ide_drive_t *drive;
ide_driver_t *driver;
struct gendisk *disk;
struct kref kref;
+ unsigned int openers; /* protected by BKL for now */
/* Current packet command */
- idefloppy_pc_t *pc;
+ struct ide_atapi_pc *pc;
/* Last failed packet command */
- idefloppy_pc_t *failed_pc;
+ struct ide_atapi_pc *failed_pc;
/* Packet command stack */
- idefloppy_pc_t pc_stack[IDEFLOPPY_PC_STACK];
+ struct ide_atapi_pc pc_stack[IDEFLOPPY_PC_STACK];
/* Next free packet command storage space */
int pc_stack_index;
struct request rq_stack[IDEFLOPPY_PC_STACK];
/* We implement a circular array */
int rq_stack_index;
- /*
- * Last error information
- */
+ /* Last error information */
u8 sense_key, asc, ascq;
/* delay this long before sending packet command */
u8 ticks;
int progress_indication;
- /*
- * Device information
- */
+ /* Device information */
/* Current format */
int blocks, block_size, bs_factor;
- /* Last format capacity */
- idefloppy_capacity_descriptor_t capacity;
+ /* Last format capacity descriptor */
+ u8 cap_desc[8];
/* Copy of the flexible disk page */
- idefloppy_flexible_disk_page_t flexible_disk_page;
+ u8 flexible_disk_page[32];
/* Write protect */
int wp;
/* Supports format progress report */
#define IDEFLOPPY_TICKS_DELAY HZ/20 /* default delay for ZIP 100 (50ms) */
-/*
- * Floppy flag bits values.
- */
-#define IDEFLOPPY_DRQ_INTERRUPT 0 /* DRQ interrupt device */
-#define IDEFLOPPY_MEDIA_CHANGED 1 /* Media may have changed */
-#define IDEFLOPPY_USE_READ12 2 /* Use READ12/WRITE12 or READ10/WRITE10 */
-#define IDEFLOPPY_FORMAT_IN_PROGRESS 3 /* Format in progress */
-#define IDEFLOPPY_CLIK_DRIVE 4 /* Avoid commands not supported in Clik drive */
-#define IDEFLOPPY_ZIP_DRIVE 5 /* Requires BH algorithm for packets */
-
-/*
- * ATAPI floppy drive packet commands
- */
-#define IDEFLOPPY_FORMAT_UNIT_CMD 0x04
-#define IDEFLOPPY_INQUIRY_CMD 0x12
-#define IDEFLOPPY_MODE_SELECT_CMD 0x55
-#define IDEFLOPPY_MODE_SENSE_CMD 0x5a
-#define IDEFLOPPY_READ10_CMD 0x28
-#define IDEFLOPPY_READ12_CMD 0xa8
-#define IDEFLOPPY_READ_CAPACITY_CMD 0x23
-#define IDEFLOPPY_REQUEST_SENSE_CMD 0x03
-#define IDEFLOPPY_PREVENT_REMOVAL_CMD 0x1e
-#define IDEFLOPPY_SEEK_CMD 0x2b
-#define IDEFLOPPY_START_STOP_CMD 0x1b
-#define IDEFLOPPY_TEST_UNIT_READY_CMD 0x00
-#define IDEFLOPPY_VERIFY_CMD 0x2f
-#define IDEFLOPPY_WRITE10_CMD 0x2a
-#define IDEFLOPPY_WRITE12_CMD 0xaa
-#define IDEFLOPPY_WRITE_VERIFY_CMD 0x2e
+/* Floppy flag bits values. */
+enum {
+ /* DRQ interrupt device */
+ IDEFLOPPY_FLAG_DRQ_INTERRUPT = (1 << 0),
+ /* Media may have changed */
+ IDEFLOPPY_FLAG_MEDIA_CHANGED = (1 << 1),
+ /* Format in progress */
+ IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS = (1 << 2),
+ /* Avoid commands not supported in Clik drive */
+ IDEFLOPPY_FLAG_CLIK_DRIVE = (1 << 3),
+ /* Requires BH algorithm for packets */
+ IDEFLOPPY_FLAG_ZIP_DRIVE = (1 << 4),
+};
-/*
- * Defines for the mode sense command
- */
+/* Defines for the MODE SENSE command */
#define MODE_SENSE_CURRENT 0x00
#define MODE_SENSE_CHANGEABLE 0x01
-#define MODE_SENSE_DEFAULT 0x02
+#define MODE_SENSE_DEFAULT 0x02
#define MODE_SENSE_SAVED 0x03
-/*
- * IOCTLs used in low-level formatting.
- */
-
+/* IOCTLs used in low-level formatting. */
#define IDEFLOPPY_IOCTL_FORMAT_SUPPORTED 0x4600
#define IDEFLOPPY_IOCTL_FORMAT_GET_CAPACITY 0x4601
#define IDEFLOPPY_IOCTL_FORMAT_START 0x4602
#define IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS 0x4603
-#if 0
-/*
- * Special requests for our block device strategy routine.
- */
-#define IDEFLOPPY_FIRST_RQ 90
-
-/*
- * IDEFLOPPY_PC_RQ is used to queue a packet command in the request queue.
- */
-#define IDEFLOPPY_PC_RQ 90
-
-#define IDEFLOPPY_LAST_RQ 90
-
-/*
- * A macro which can be used to check if a given request command
- * originated in the driver or in the buffer cache layer.
- */
-#define IDEFLOPPY_RQ_CMD(cmd) ((cmd >= IDEFLOPPY_FIRST_RQ) && (cmd <= IDEFLOPPY_LAST_RQ))
-
-#endif
-
-/*
- * Error codes which are returned in rq->errors to the higher part
- * of the driver.
- */
+/* Error code returned in rq->errors to the higher part of the driver. */
#define IDEFLOPPY_ERROR_GENERAL 101
/*
- * The following is used to format the general configuration word of
- * the ATAPI IDENTIFY DEVICE command.
- */
-struct idefloppy_id_gcw {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned packet_size :2; /* Packet Size */
- unsigned reserved234 :3; /* Reserved */
- unsigned drq_type :2; /* Command packet DRQ type */
- unsigned removable :1; /* Removable media */
- unsigned device_type :5; /* Device type */
- unsigned reserved13 :1; /* Reserved */
- unsigned protocol :2; /* Protocol type */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned protocol :2; /* Protocol type */
- unsigned reserved13 :1; /* Reserved */
- unsigned device_type :5; /* Device type */
- unsigned removable :1; /* Removable media */
- unsigned drq_type :2; /* Command packet DRQ type */
- unsigned reserved234 :3; /* Reserved */
- unsigned packet_size :2; /* Packet Size */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
-};
-
-/*
- * INQUIRY packet command - Data Format
- */
-typedef struct {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned device_type :5; /* Peripheral Device Type */
- unsigned reserved0_765 :3; /* Peripheral Qualifier - Reserved */
- unsigned reserved1_6t0 :7; /* Reserved */
- unsigned rmb :1; /* Removable Medium Bit */
- unsigned ansi_version :3; /* ANSI Version */
- unsigned ecma_version :3; /* ECMA Version */
- unsigned iso_version :2; /* ISO Version */
- unsigned response_format :4; /* Response Data Format */
- unsigned reserved3_45 :2; /* Reserved */
- unsigned reserved3_6 :1; /* TrmIOP - Reserved */
- unsigned reserved3_7 :1; /* AENC - Reserved */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned reserved0_765 :3; /* Peripheral Qualifier - Reserved */
- unsigned device_type :5; /* Peripheral Device Type */
- unsigned rmb :1; /* Removable Medium Bit */
- unsigned reserved1_6t0 :7; /* Reserved */
- unsigned iso_version :2; /* ISO Version */
- unsigned ecma_version :3; /* ECMA Version */
- unsigned ansi_version :3; /* ANSI Version */
- unsigned reserved3_7 :1; /* AENC - Reserved */
- unsigned reserved3_6 :1; /* TrmIOP - Reserved */
- unsigned reserved3_45 :2; /* Reserved */
- unsigned response_format :4; /* Response Data Format */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 additional_length; /* Additional Length (total_length-4) */
- u8 rsv5, rsv6, rsv7; /* Reserved */
- u8 vendor_id[8]; /* Vendor Identification */
- u8 product_id[16]; /* Product Identification */
- u8 revision_level[4]; /* Revision Level */
- u8 vendor_specific[20]; /* Vendor Specific - Optional */
- u8 reserved56t95[40]; /* Reserved - Optional */
- /* Additional information may be returned */
-} idefloppy_inquiry_result_t;
-
-/*
- * REQUEST SENSE packet command result - Data Format.
- */
-typedef struct {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned error_code :7; /* Current error (0x70) */
- unsigned valid :1; /* The information field conforms to SFF-8070i */
- u8 reserved1 :8; /* Reserved */
- unsigned sense_key :4; /* Sense Key */
- unsigned reserved2_4 :1; /* Reserved */
- unsigned ili :1; /* Incorrect Length Indicator */
- unsigned reserved2_67 :2;
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned valid :1; /* The information field conforms to SFF-8070i */
- unsigned error_code :7; /* Current error (0x70) */
- u8 reserved1 :8; /* Reserved */
- unsigned reserved2_67 :2;
- unsigned ili :1; /* Incorrect Length Indicator */
- unsigned reserved2_4 :1; /* Reserved */
- unsigned sense_key :4; /* Sense Key */
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u32 information __attribute__ ((packed));
- u8 asl; /* Additional sense length (n-7) */
- u32 command_specific; /* Additional command specific information */
- u8 asc; /* Additional Sense Code */
- u8 ascq; /* Additional Sense Code Qualifier */
- u8 replaceable_unit_code; /* Field Replaceable Unit Code */
- u8 sksv[3];
- u8 pad[2]; /* Padding to 20 bytes */
-} idefloppy_request_sense_result_t;
-
-/*
- * Pages of the SELECT SENSE / MODE SENSE packet commands.
+ * Pages of the SELECT SENSE / MODE SENSE packet commands.
+ * See SFF-8070i spec.
*/
#define IDEFLOPPY_CAPABILITIES_PAGE 0x1b
#define IDEFLOPPY_FLEXIBLE_DISK_PAGE 0x05
-/*
- * Mode Parameter Header for the MODE SENSE packet command
- */
-typedef struct {
- u16 mode_data_length; /* Length of the following data transfer */
- u8 medium_type; /* Medium Type */
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned reserved3 :7;
- unsigned wp :1; /* Write protect */
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned wp :1; /* Write protect */
- unsigned reserved3 :7;
-#else
-#error "Bitfield endianness not defined! Check your byteorder.h"
-#endif
- u8 reserved[4];
-} idefloppy_mode_parameter_header_t;
-
-static DECLARE_MUTEX(idefloppy_ref_sem);
+static DEFINE_MUTEX(idefloppy_ref_mutex);
#define to_ide_floppy(obj) container_of(obj, struct ide_floppy_obj, kref)
{
struct ide_floppy_obj *floppy = NULL;
- down(&idefloppy_ref_sem);
+ mutex_lock(&idefloppy_ref_mutex);
floppy = ide_floppy_g(disk);
if (floppy)
kref_get(&floppy->kref);
- up(&idefloppy_ref_sem);
+ mutex_unlock(&idefloppy_ref_mutex);
return floppy;
}
-static void ide_floppy_release(struct kref *);
+static void idefloppy_cleanup_obj(struct kref *);
static void ide_floppy_put(struct ide_floppy_obj *floppy)
{
- down(&idefloppy_ref_sem);
- kref_put(&floppy->kref, ide_floppy_release);
- up(&idefloppy_ref_sem);
-}
-
-/*
- * Too bad. The drive wants to send us data which we are not ready to accept.
- * Just throw it away.
- */
-static void idefloppy_discard_data (ide_drive_t *drive, unsigned int bcount)
-{
- while (bcount--)
- (void) HWIF(drive)->INB(IDE_DATA_REG);
-}
-
-#if IDEFLOPPY_DEBUG_BUGS
-static void idefloppy_write_zeros (ide_drive_t *drive, unsigned int bcount)
-{
- while (bcount--)
- HWIF(drive)->OUTB(0, IDE_DATA_REG);
+ mutex_lock(&idefloppy_ref_mutex);
+ kref_put(&floppy->kref, idefloppy_cleanup_obj);
+ mutex_unlock(&idefloppy_ref_mutex);
}
-#endif /* IDEFLOPPY_DEBUG_BUGS */
-
/*
- * idefloppy_do_end_request is used to finish servicing a request.
- *
- * For read/write requests, we will call ide_end_request to pass to the
- * next buffer.
+ * Used to finish servicing a request. For read/write requests, we will call
+ * ide_end_request to pass to the next buffer.
*/
-static int idefloppy_do_end_request(ide_drive_t *drive, int uptodate, int nsecs)
+static int idefloppy_end_request(ide_drive_t *drive, int uptodate, int nsecs)
{
idefloppy_floppy_t *floppy = drive->driver_data;
struct request *rq = HWGROUP(drive)->rq;
int error;
- debug_log(KERN_INFO "Reached idefloppy_end_request\n");
+ debug_log("Reached %s\n", __func__);
switch (uptodate) {
- case 0: error = IDEFLOPPY_ERROR_GENERAL; break;
- case 1: error = 0; break;
- default: error = uptodate;
+ case 0: error = IDEFLOPPY_ERROR_GENERAL; break;
+ case 1: error = 0; break;
+ default: error = uptodate;
}
if (error)
floppy->failed_pc = NULL;
/* Why does this happen? */
if (!rq)
return 0;
- if (!(rq->flags & REQ_SPECIAL)) { //if (!IDEFLOPPY_RQ_CMD (rq->cmd)) {
+ if (!blk_special_request(rq)) {
/* our real local end request function */
ide_end_request(drive, uptodate, nsecs);
return 0;
return 0;
}
-static void idefloppy_input_buffers (ide_drive_t *drive, idefloppy_pc_t *pc, unsigned int bcount)
-{
- struct request *rq = pc->rq;
- struct bio_vec *bvec;
- struct bio *bio;
- unsigned long flags;
- char *data;
- int count, i, done = 0;
-
- rq_for_each_bio(bio, rq) {
- bio_for_each_segment(bvec, bio, i) {
- if (!bcount)
- break;
-
- count = min(bvec->bv_len, bcount);
-
- data = bvec_kmap_irq(bvec, &flags);
- drive->hwif->atapi_input_bytes(drive, data, count);
- bvec_kunmap_irq(data, &flags);
-
- bcount -= count;
- pc->b_count += count;
- done += count;
- }
- }
-
- idefloppy_do_end_request(drive, 1, done >> 9);
-
- if (bcount) {
- printk(KERN_ERR "%s: leftover data in idefloppy_input_buffers, bcount == %d\n", drive->name, bcount);
- idefloppy_discard_data(drive, bcount);
- }
-}
-
-static void idefloppy_output_buffers (ide_drive_t *drive, idefloppy_pc_t *pc, unsigned int bcount)
+static void ide_floppy_io_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc,
+ unsigned int bcount, int direction)
{
+ ide_hwif_t *hwif = drive->hwif;
struct request *rq = pc->rq;
- struct bio *bio;
+ struct req_iterator iter;
struct bio_vec *bvec;
unsigned long flags;
- int count, i, done = 0;
+ int count, done = 0;
char *data;
- rq_for_each_bio(bio, rq) {
- bio_for_each_segment(bvec, bio, i) {
- if (!bcount)
- break;
+ rq_for_each_segment(bvec, rq, iter) {
+ if (!bcount)
+ break;
- count = min(bvec->bv_len, bcount);
+ count = min(bvec->bv_len, bcount);
- data = bvec_kmap_irq(bvec, &flags);
- drive->hwif->atapi_output_bytes(drive, data, count);
- bvec_kunmap_irq(data, &flags);
+ data = bvec_kmap_irq(bvec, &flags);
+ if (direction)
+ hwif->output_data(drive, NULL, data, count);
+ else
+ hwif->input_data(drive, NULL, data, count);
+ bvec_kunmap_irq(data, &flags);
- bcount -= count;
- pc->b_count += count;
- done += count;
- }
+ bcount -= count;
+ pc->b_count += count;
+ done += count;
}
- idefloppy_do_end_request(drive, 1, done >> 9);
+ idefloppy_end_request(drive, 1, done >> 9);
-#if IDEFLOPPY_DEBUG_BUGS
if (bcount) {
- printk(KERN_ERR "%s: leftover data in idefloppy_output_buffers, bcount == %d\n", drive->name, bcount);
- idefloppy_write_zeros(drive, bcount);
+ printk(KERN_ERR "%s: leftover data in %s, bcount == %d\n",
+ drive->name, __func__, bcount);
+ ide_pad_transfer(drive, direction, bcount);
}
-#endif
}
-static void idefloppy_update_buffers (ide_drive_t *drive, idefloppy_pc_t *pc)
+static void idefloppy_update_buffers(ide_drive_t *drive,
+ struct ide_atapi_pc *pc)
{
struct request *rq = pc->rq;
struct bio *bio = rq->bio;
while ((bio = rq->bio) != NULL)
- idefloppy_do_end_request(drive, 1, 0);
+ idefloppy_end_request(drive, 1, 0);
}
/*
- * idefloppy_queue_pc_head generates a new packet command request in front
- * of the request queue, before the current request, so that it will be
- * processed immediately, on the next pass through the driver.
+ * Generate a new packet command request in front of the request queue, before
+ * the current request so that it will be processed immediately, on the next
+ * pass through the driver.
*/
-static void idefloppy_queue_pc_head (ide_drive_t *drive,idefloppy_pc_t *pc,struct request *rq)
+static void idefloppy_queue_pc_head(ide_drive_t *drive, struct ide_atapi_pc *pc,
+ struct request *rq)
{
struct ide_floppy_obj *floppy = drive->driver_data;
ide_init_drive_cmd(rq);
rq->buffer = (char *) pc;
- rq->flags = REQ_SPECIAL; //rq->cmd = IDEFLOPPY_PC_RQ;
+ rq->cmd_type = REQ_TYPE_SPECIAL;
rq->rq_disk = floppy->disk;
(void) ide_do_drive_cmd(drive, rq, ide_preempt);
}
-static idefloppy_pc_t *idefloppy_next_pc_storage (ide_drive_t *drive)
+static struct ide_atapi_pc *idefloppy_next_pc_storage(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
if (floppy->pc_stack_index == IDEFLOPPY_PC_STACK)
- floppy->pc_stack_index=0;
+ floppy->pc_stack_index = 0;
return (&floppy->pc_stack[floppy->pc_stack_index++]);
}
-static struct request *idefloppy_next_rq_storage (ide_drive_t *drive)
+static struct request *idefloppy_next_rq_storage(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
return (&floppy->rq_stack[floppy->rq_stack_index++]);
}
-/*
- * idefloppy_analyze_error is called on each failed packet command retry
- * to analyze the request sense.
- */
-static void idefloppy_analyze_error (ide_drive_t *drive,idefloppy_request_sense_result_t *result)
+static void idefloppy_request_sense_callback(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
+ u8 *buf = floppy->pc->buf;
- floppy->sense_key = result->sense_key;
- floppy->asc = result->asc;
- floppy->ascq = result->ascq;
- floppy->progress_indication = result->sksv[0] & 0x80 ?
- (u16)get_unaligned((u16 *)(result->sksv+1)):0x10000;
- if (floppy->failed_pc)
- debug_log(KERN_INFO "ide-floppy: pc = %x, sense key = %x, "
- "asc = %x, ascq = %x\n", floppy->failed_pc->c[0],
- result->sense_key, result->asc, result->ascq);
- else
- debug_log(KERN_INFO "ide-floppy: sense key = %x, asc = %x, "
- "ascq = %x\n", result->sense_key,
- result->asc, result->ascq);
-}
-
-static void idefloppy_request_sense_callback (ide_drive_t *drive)
-{
- idefloppy_floppy_t *floppy = drive->driver_data;
+ debug_log("Reached %s\n", __func__);
- debug_log(KERN_INFO "ide-floppy: Reached %s\n", __FUNCTION__);
-
if (!floppy->pc->error) {
- idefloppy_analyze_error(drive,(idefloppy_request_sense_result_t *) floppy->pc->buffer);
- idefloppy_do_end_request(drive, 1, 0);
+ floppy->sense_key = buf[2] & 0x0F;
+ floppy->asc = buf[12];
+ floppy->ascq = buf[13];
+ floppy->progress_indication = buf[15] & 0x80 ?
+ (u16)get_unaligned((u16 *)&buf[16]) : 0x10000;
+
+ if (floppy->failed_pc)
+ debug_log("pc = %x, sense key = %x, asc = %x,"
+ " ascq = %x\n",
+ floppy->failed_pc->c[0],
+ floppy->sense_key,
+ floppy->asc,
+ floppy->ascq);
+ else
+ debug_log("sense key = %x, asc = %x, ascq = %x\n",
+ floppy->sense_key,
+ floppy->asc,
+ floppy->ascq);
+
+
+ idefloppy_end_request(drive, 1, 0);
} else {
- printk(KERN_ERR "Error in REQUEST SENSE itself - Aborting request!\n");
- idefloppy_do_end_request(drive, 0, 0);
+ printk(KERN_ERR "Error in REQUEST SENSE itself - Aborting"
+ " request!\n");
+ idefloppy_end_request(drive, 0, 0);
}
}
-/*
- * General packet command callback function.
- */
-static void idefloppy_pc_callback (ide_drive_t *drive)
+/* General packet command callback function. */
+static void idefloppy_pc_callback(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
-
- debug_log(KERN_INFO "ide-floppy: Reached %s\n", __FUNCTION__);
- idefloppy_do_end_request(drive, floppy->pc->error ? 0 : 1, 0);
+ debug_log("Reached %s\n", __func__);
+
+ idefloppy_end_request(drive, floppy->pc->error ? 0 : 1, 0);
}
-/*
- * idefloppy_init_pc initializes a packet command.
- */
-static void idefloppy_init_pc (idefloppy_pc_t *pc)
+static void idefloppy_init_pc(struct ide_atapi_pc *pc)
{
memset(pc->c, 0, 12);
pc->retries = 0;
pc->flags = 0;
- pc->request_transfer = 0;
- pc->buffer = pc->pc_buffer;
- pc->buffer_size = IDEFLOPPY_PC_BUFFER_SIZE;
- pc->callback = &idefloppy_pc_callback;
+ pc->req_xfer = 0;
+ pc->buf = pc->pc_buf;
+ pc->buf_size = IDEFLOPPY_PC_BUFFER_SIZE;
+ pc->idefloppy_callback = &idefloppy_pc_callback;
}
-static void idefloppy_create_request_sense_cmd (idefloppy_pc_t *pc)
+static void idefloppy_create_request_sense_cmd(struct ide_atapi_pc *pc)
{
- idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_REQUEST_SENSE_CMD;
+ idefloppy_init_pc(pc);
+ pc->c[0] = GPCMD_REQUEST_SENSE;
pc->c[4] = 255;
- pc->request_transfer = 18;
- pc->callback = &idefloppy_request_sense_callback;
+ pc->req_xfer = 18;
+ pc->idefloppy_callback = &idefloppy_request_sense_callback;
}
/*
- * idefloppy_retry_pc is called when an error was detected during the
- * last packet command. We queue a request sense packet command in
- * the head of the request list.
+ * Called when an error was detected during the last packet command. We queue a
+ * request sense packet command in the head of the request list.
*/
-static void idefloppy_retry_pc (ide_drive_t *drive)
+static void idefloppy_retry_pc(ide_drive_t *drive)
{
- idefloppy_pc_t *pc;
+ struct ide_atapi_pc *pc;
struct request *rq;
- atapi_error_t error;
- error.all = HWIF(drive)->INB(IDE_ERROR_REG);
+ (void)ide_read_error(drive);
pc = idefloppy_next_pc_storage(drive);
rq = idefloppy_next_rq_storage(drive);
idefloppy_create_request_sense_cmd(pc);
idefloppy_queue_pc_head(drive, pc, rq);
}
-/*
- * idefloppy_pc_intr is the usual interrupt handler which will be called
- * during a packet command.
- */
-static ide_startstop_t idefloppy_pc_intr (ide_drive_t *drive)
+/* The usual interrupt handler called during a packet command. */
+static ide_startstop_t idefloppy_pc_intr(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- atapi_status_t status;
- atapi_bcount_t bcount;
- atapi_ireason_t ireason;
- idefloppy_pc_t *pc = floppy->pc;
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_atapi_pc *pc = floppy->pc;
struct request *rq = pc->rq;
+ xfer_func_t *xferfunc;
unsigned int temp;
-
- debug_log(KERN_INFO "ide-floppy: Reached %s interrupt handler\n",
- __FUNCTION__);
-
- if (test_bit(PC_DMA_IN_PROGRESS, &pc->flags)) {
- if (HWIF(drive)->ide_dma_end(drive)) {
- set_bit(PC_DMA_ERROR, &pc->flags);
+ int dma_error = 0;
+ u16 bcount;
+ u8 stat, ireason;
+
+ debug_log("Reached %s interrupt handler\n", __func__);
+
+ if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) {
+ dma_error = hwif->dma_ops->dma_end(drive);
+ if (dma_error) {
+ printk(KERN_ERR "%s: DMA %s error\n", drive->name,
+ rq_data_dir(rq) ? "write" : "read");
+ pc->flags |= PC_FLAG_DMA_ERROR;
} else {
- pc->actually_transferred = pc->request_transfer;
+ pc->xferred = pc->req_xfer;
idefloppy_update_buffers(drive, pc);
}
- debug_log(KERN_INFO "ide-floppy: DMA finished\n");
+ debug_log("DMA finished\n");
}
/* Clear the interrupt */
- status.all = HWIF(drive)->INB(IDE_STATUS_REG);
+ stat = ide_read_status(drive);
- if (!status.b.drq) { /* No more interrupts */
- debug_log(KERN_INFO "Packet command completed, %d bytes "
- "transferred\n", pc->actually_transferred);
- clear_bit(PC_DMA_IN_PROGRESS, &pc->flags);
+ /* No more interrupts */
+ if ((stat & DRQ_STAT) == 0) {
+ debug_log("Packet command completed, %d bytes transferred\n",
+ pc->xferred);
+ pc->flags &= ~PC_FLAG_DMA_IN_PROGRESS;
- local_irq_enable();
+ local_irq_enable_in_hardirq();
- if (status.b.check || test_bit(PC_DMA_ERROR, &pc->flags)) {
+ if ((stat & ERR_STAT) || (pc->flags & PC_FLAG_DMA_ERROR)) {
/* Error detected */
- debug_log(KERN_INFO "ide-floppy: %s: I/O error\n",
- drive->name);
+ debug_log("%s: I/O error\n", drive->name);
rq->errors++;
- if (pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD) {
+ if (pc->c[0] == GPCMD_REQUEST_SENSE) {
printk(KERN_ERR "ide-floppy: I/O error in "
"request sense command\n");
return ide_do_reset(drive);
if (floppy->failed_pc == pc)
floppy->failed_pc = NULL;
/* Command finished - Call the callback function */
- pc->callback(drive);
+ pc->idefloppy_callback(drive);
return ide_stopped;
}
- if (test_and_clear_bit(PC_DMA_IN_PROGRESS, &pc->flags)) {
+ if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) {
+ pc->flags &= ~PC_FLAG_DMA_IN_PROGRESS;
printk(KERN_ERR "ide-floppy: The floppy wants to issue "
"more interrupts in DMA mode\n");
- (void)__ide_dma_off(drive);
+ ide_dma_off(drive);
return ide_do_reset(drive);
}
/* Get the number of bytes to transfer */
- bcount.b.high = HWIF(drive)->INB(IDE_BCOUNTH_REG);
- bcount.b.low = HWIF(drive)->INB(IDE_BCOUNTL_REG);
+ bcount = (hwif->INB(hwif->io_ports.lbah_addr) << 8) |
+ hwif->INB(hwif->io_ports.lbam_addr);
/* on this interrupt */
- ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
+ ireason = hwif->INB(hwif->io_ports.nsect_addr);
- if (ireason.b.cod) {
- printk(KERN_ERR "ide-floppy: CoD != 0 in idefloppy_pc_intr\n");
+ if (ireason & CD) {
+ printk(KERN_ERR "ide-floppy: CoD != 0 in %s\n", __func__);
return ide_do_reset(drive);
}
- if (ireason.b.io == test_bit(PC_WRITING, &pc->flags)) {
+ if (((ireason & IO) == IO) == !!(pc->flags & PC_FLAG_WRITING)) {
/* Hopefully, we will never get here */
printk(KERN_ERR "ide-floppy: We wanted to %s, ",
- ireason.b.io ? "Write":"Read");
+ (ireason & IO) ? "Write" : "Read");
printk(KERN_ERR "but the floppy wants us to %s !\n",
- ireason.b.io ? "Read":"Write");
+ (ireason & IO) ? "Read" : "Write");
return ide_do_reset(drive);
}
- if (!test_bit(PC_WRITING, &pc->flags)) {
+ if (!(pc->flags & PC_FLAG_WRITING)) {
/* Reading - Check that we have enough space */
- temp = pc->actually_transferred + bcount.all;
- if (temp > pc->request_transfer) {
- if (temp > pc->buffer_size) {
+ temp = pc->xferred + bcount;
+ if (temp > pc->req_xfer) {
+ if (temp > pc->buf_size) {
printk(KERN_ERR "ide-floppy: The floppy wants "
"to send us more data than expected "
"- discarding data\n");
- idefloppy_discard_data(drive,bcount.all);
- if (HWGROUP(drive)->handler != NULL)
- BUG();
+ ide_pad_transfer(drive, 0, bcount);
+
ide_set_handler(drive,
&idefloppy_pc_intr,
IDEFLOPPY_WAIT_CMD,
NULL);
return ide_started;
}
- debug_log(KERN_NOTICE "ide-floppy: The floppy wants to "
- "send us more data than expected - "
- "allowing transfer\n");
+ debug_log("The floppy wants to send us more data than"
+ " expected - allowing transfer\n");
}
}
- if (test_bit(PC_WRITING, &pc->flags)) {
- if (pc->buffer != NULL)
- /* Write the current buffer */
- HWIF(drive)->atapi_output_bytes(drive,
- pc->current_position,
- bcount.all);
- else
- idefloppy_output_buffers(drive, pc, bcount.all);
- } else {
- if (pc->buffer != NULL)
- /* Read the current buffer */
- HWIF(drive)->atapi_input_bytes(drive,
- pc->current_position,
- bcount.all);
- else
- idefloppy_input_buffers(drive, pc, bcount.all);
- }
+ if (pc->flags & PC_FLAG_WRITING)
+ xferfunc = hwif->output_data;
+ else
+ xferfunc = hwif->input_data;
+
+ if (pc->buf)
+ xferfunc(drive, NULL, pc->cur_pos, bcount);
+ else
+ ide_floppy_io_buffers(drive, pc, bcount,
+ !!(pc->flags & PC_FLAG_WRITING));
+
/* Update the current position */
- pc->actually_transferred += bcount.all;
- pc->current_position += bcount.all;
+ pc->xferred += bcount;
+ pc->cur_pos += bcount;
- if (HWGROUP(drive)->handler != NULL)
- BUG();
- ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL); /* And set the interrupt handler again */
+ /* And set the interrupt handler again */
+ ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL);
return ide_started;
}
* It fails at high speeds on the Iomega ZIP drive, so there's a slower version
* for that drive below. The algorithm is chosen based on drive type
*/
-static ide_startstop_t idefloppy_transfer_pc (ide_drive_t *drive)
+static ide_startstop_t idefloppy_transfer_pc(ide_drive_t *drive)
{
+ ide_hwif_t *hwif = drive->hwif;
ide_startstop_t startstop;
idefloppy_floppy_t *floppy = drive->driver_data;
- atapi_ireason_t ireason;
+ u8 ireason;
if (ide_wait_stat(&startstop, drive, DRQ_STAT, BUSY_STAT, WAIT_READY)) {
printk(KERN_ERR "ide-floppy: Strange, packet command "
"initiated yet DRQ isn't asserted\n");
return startstop;
}
- ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
- if (!ireason.b.cod || ireason.b.io) {
+ ireason = hwif->INB(hwif->io_ports.nsect_addr);
+ if ((ireason & CD) == 0 || (ireason & IO)) {
printk(KERN_ERR "ide-floppy: (IO,CoD) != (0,1) while "
"issuing a packet command\n");
return ide_do_reset(drive);
}
- if (HWGROUP(drive)->handler != NULL)
- BUG();
+
/* Set the interrupt routine */
ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL);
+
/* Send the actual packet */
- HWIF(drive)->atapi_output_bytes(drive, floppy->pc->c, 12);
+ hwif->output_data(drive, NULL, floppy->pc->c, 12);
+
return ide_started;
}
/*
- * What we have here is a classic case of a top half / bottom half
- * interrupt service routine. In interrupt mode, the device sends
- * an interrupt to signal it's ready to receive a packet. However,
- * we need to delay about 2-3 ticks before issuing the packet or we
- * gets in trouble.
+ * What we have here is a classic case of a top half / bottom half interrupt
+ * service routine. In interrupt mode, the device sends an interrupt to signal
+ * that it is ready to receive a packet. However, we need to delay about 2-3
+ * ticks before issuing the packet or we gets in trouble.
*
- * So, follow carefully. transfer_pc1 is called as an interrupt (or
- * directly). In either case, when the device says it's ready for a
- * packet, we schedule the packet transfer to occur about 2-3 ticks
- * later in transfer_pc2.
+ * So, follow carefully. transfer_pc1 is called as an interrupt (or directly).
+ * In either case, when the device says it's ready for a packet, we schedule
+ * the packet transfer to occur about 2-3 ticks later in transfer_pc2.
*/
-static int idefloppy_transfer_pc2 (ide_drive_t *drive)
+static int idefloppy_transfer_pc2(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
/* Send the actual packet */
- HWIF(drive)->atapi_output_bytes(drive, floppy->pc->c, 12);
+ drive->hwif->output_data(drive, NULL, floppy->pc->c, 12);
+
/* Timeout for the packet command */
return IDEFLOPPY_WAIT_CMD;
}
-static ide_startstop_t idefloppy_transfer_pc1 (ide_drive_t *drive)
+static ide_startstop_t idefloppy_transfer_pc1(ide_drive_t *drive)
{
+ ide_hwif_t *hwif = drive->hwif;
idefloppy_floppy_t *floppy = drive->driver_data;
ide_startstop_t startstop;
- atapi_ireason_t ireason;
+ u8 ireason;
if (ide_wait_stat(&startstop, drive, DRQ_STAT, BUSY_STAT, WAIT_READY)) {
printk(KERN_ERR "ide-floppy: Strange, packet command "
"initiated yet DRQ isn't asserted\n");
return startstop;
}
- ireason.all = HWIF(drive)->INB(IDE_IREASON_REG);
- if (!ireason.b.cod || ireason.b.io) {
+ ireason = hwif->INB(hwif->io_ports.nsect_addr);
+ if ((ireason & CD) == 0 || (ireason & IO)) {
printk(KERN_ERR "ide-floppy: (IO,CoD) != (0,1) "
"while issuing a packet command\n");
return ide_do_reset(drive);
}
- /*
+ /*
* The following delay solves a problem with ATAPI Zip 100 drives
* where the Busy flag was apparently being deasserted before the
* unit was ready to receive data. This was happening on a
* 40 and 50msec work well. idefloppy_pc_intr will not be actually
* used until after the packet is moved in about 50 msec.
*/
- if (HWGROUP(drive)->handler != NULL)
- BUG();
- ide_set_handler(drive,
- &idefloppy_pc_intr, /* service routine for packet command */
- floppy->ticks, /* wait this long before "failing" */
- &idefloppy_transfer_pc2); /* fail == transfer_pc2 */
+
+ ide_set_handler(drive, &idefloppy_pc_intr, floppy->ticks,
+ &idefloppy_transfer_pc2);
return ide_started;
}
-/**
- * idefloppy_should_report_error()
- *
- * Supresses error messages resulting from Medium not present
- */
-static inline int idefloppy_should_report_error(idefloppy_floppy_t *floppy)
+static void ide_floppy_report_error(idefloppy_floppy_t *floppy,
+ struct ide_atapi_pc *pc)
{
+ /* supress error messages resulting from Medium not present */
if (floppy->sense_key == 0x02 &&
floppy->asc == 0x3a &&
floppy->ascq == 0x00)
- return 0;
- return 1;
+ return;
+
+ printk(KERN_ERR "ide-floppy: %s: I/O error, pc = %2x, key = %2x, "
+ "asc = %2x, ascq = %2x\n",
+ floppy->drive->name, pc->c[0], floppy->sense_key,
+ floppy->asc, floppy->ascq);
+
}
-/*
- * Issue a packet command
- */
-static ide_startstop_t idefloppy_issue_pc (ide_drive_t *drive, idefloppy_pc_t *pc)
+static ide_startstop_t idefloppy_issue_pc(ide_drive_t *drive,
+ struct ide_atapi_pc *pc)
{
idefloppy_floppy_t *floppy = drive->driver_data;
ide_hwif_t *hwif = drive->hwif;
- atapi_feature_t feature;
- atapi_bcount_t bcount;
ide_handler_t *pkt_xfer_routine;
-
-#if 0 /* Accessing floppy->pc is not valid here, the previous pc may be gone
- and have lived on another thread's stack; that stack may have become
- unmapped meanwhile (CONFIG_DEBUG_PAGEALLOC). */
-#if IDEFLOPPY_DEBUG_BUGS
- if (floppy->pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD &&
- pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD) {
- printk(KERN_ERR "ide-floppy: possible ide-floppy.c bug - "
- "Two request sense in serial were issued\n");
- }
-#endif /* IDEFLOPPY_DEBUG_BUGS */
-#endif
+ u16 bcount;
+ u8 dma;
if (floppy->failed_pc == NULL &&
- pc->c[0] != IDEFLOPPY_REQUEST_SENSE_CMD)
+ pc->c[0] != GPCMD_REQUEST_SENSE)
floppy->failed_pc = pc;
/* Set the current packet command */
floppy->pc = pc;
- if (pc->retries > IDEFLOPPY_MAX_PC_RETRIES ||
- test_bit(PC_ABORT, &pc->flags)) {
- /*
- * We will "abort" retrying a packet command in case
- * a legitimate error code was received.
- */
- if (!test_bit(PC_ABORT, &pc->flags)) {
- if (!test_bit(PC_SUPPRESS_ERROR, &pc->flags)) {
- if (idefloppy_should_report_error(floppy))
- printk(KERN_ERR "ide-floppy: %s: I/O error, "
- "pc = %2x, key = %2x, "
- "asc = %2x, ascq = %2x\n",
- drive->name, pc->c[0],
- floppy->sense_key,
- floppy->asc, floppy->ascq);
- }
- /* Giving up */
- pc->error = IDEFLOPPY_ERROR_GENERAL;
- }
+ if (pc->retries > IDEFLOPPY_MAX_PC_RETRIES) {
+ if (!(pc->flags & PC_FLAG_SUPPRESS_ERROR))
+ ide_floppy_report_error(floppy, pc);
+ /* Giving up */
+ pc->error = IDEFLOPPY_ERROR_GENERAL;
+
floppy->failed_pc = NULL;
- pc->callback(drive);
+ pc->idefloppy_callback(drive);
return ide_stopped;
}
- debug_log(KERN_INFO "Retry number - %d\n",pc->retries);
+ debug_log("Retry number - %d\n", pc->retries);
pc->retries++;
/* We haven't transferred any data yet */
- pc->actually_transferred = 0;
- pc->current_position = pc->buffer;
- bcount.all = min(pc->request_transfer, 63 * 1024);
+ pc->xferred = 0;
+ pc->cur_pos = pc->buf;
+ bcount = min(pc->req_xfer, 63 * 1024);
- if (test_and_clear_bit(PC_DMA_ERROR, &pc->flags)) {
- (void)__ide_dma_off(drive);
+ if (pc->flags & PC_FLAG_DMA_ERROR) {
+ pc->flags &= ~PC_FLAG_DMA_ERROR;
+ ide_dma_off(drive);
}
- feature.all = 0;
-
- if (test_bit(PC_DMA_RECOMMENDED, &pc->flags) && drive->using_dma)
- feature.b.dma = !hwif->dma_setup(drive);
-
- if (IDE_CONTROL_REG)
- HWIF(drive)->OUTB(drive->ctl, IDE_CONTROL_REG);
- /* Use PIO/DMA */
- HWIF(drive)->OUTB(feature.all, IDE_FEATURE_REG);
- HWIF(drive)->OUTB(bcount.b.high, IDE_BCOUNTH_REG);
- HWIF(drive)->OUTB(bcount.b.low, IDE_BCOUNTL_REG);
- HWIF(drive)->OUTB(drive->select.all, IDE_SELECT_REG);
-
- if (feature.b.dma) { /* Begin DMA, if necessary */
- set_bit(PC_DMA_IN_PROGRESS, &pc->flags);
- hwif->dma_start(drive);
+ dma = 0;
+
+ if ((pc->flags & PC_FLAG_DMA_RECOMMENDED) && drive->using_dma)
+ dma = !hwif->dma_ops->dma_setup(drive);
+
+ ide_pktcmd_tf_load(drive, IDE_TFLAG_NO_SELECT_MASK |
+ IDE_TFLAG_OUT_DEVICE, bcount, dma);
+
+ if (dma) {
+ /* Begin DMA, if necessary */
+ pc->flags |= PC_FLAG_DMA_IN_PROGRESS;
+ hwif->dma_ops->dma_start(drive);
}
/* Can we transfer the packet when we get the interrupt or wait? */
- if (test_bit(IDEFLOPPY_ZIP_DRIVE, &floppy->flags)) {
+ if (floppy->flags & IDEFLOPPY_FLAG_ZIP_DRIVE) {
/* wait */
pkt_xfer_routine = &idefloppy_transfer_pc1;
} else {
/* immediate */
pkt_xfer_routine = &idefloppy_transfer_pc;
}
-
- if (test_bit (IDEFLOPPY_DRQ_INTERRUPT, &floppy->flags)) {
+
+ if (floppy->flags & IDEFLOPPY_FLAG_DRQ_INTERRUPT) {
/* Issue the packet command */
ide_execute_command(drive, WIN_PACKETCMD,
pkt_xfer_routine,
return ide_started;
} else {
/* Issue the packet command */
- HWIF(drive)->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG);
+ ide_execute_pkt_cmd(drive);
return (*pkt_xfer_routine) (drive);
}
}
-static void idefloppy_rw_callback (ide_drive_t *drive)
+static void idefloppy_rw_callback(ide_drive_t *drive)
{
- debug_log(KERN_INFO "ide-floppy: Reached idefloppy_rw_callback\n");
+ debug_log("Reached %s\n", __func__);
- idefloppy_do_end_request(drive, 1, 0);
+ idefloppy_end_request(drive, 1, 0);
return;
}
-static void idefloppy_create_prevent_cmd (idefloppy_pc_t *pc, int prevent)
+static void idefloppy_create_prevent_cmd(struct ide_atapi_pc *pc, int prevent)
{
- debug_log(KERN_INFO "ide-floppy: creating prevent removal command, "
- "prevent = %d\n", prevent);
+ debug_log("creating prevent removal command, prevent = %d\n", prevent);
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_PREVENT_REMOVAL_CMD;
+ pc->c[0] = GPCMD_PREVENT_ALLOW_MEDIUM_REMOVAL;
pc->c[4] = prevent;
}
-static void idefloppy_create_read_capacity_cmd (idefloppy_pc_t *pc)
+static void idefloppy_create_read_capacity_cmd(struct ide_atapi_pc *pc)
{
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_READ_CAPACITY_CMD;
+ pc->c[0] = GPCMD_READ_FORMAT_CAPACITIES;
pc->c[7] = 255;
pc->c[8] = 255;
- pc->request_transfer = 255;
+ pc->req_xfer = 255;
}
-static void idefloppy_create_format_unit_cmd (idefloppy_pc_t *pc, int b, int l,
- int flags)
+static void idefloppy_create_format_unit_cmd(struct ide_atapi_pc *pc, int b,
+ int l, int flags)
{
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_FORMAT_UNIT_CMD;
+ pc->c[0] = GPCMD_FORMAT_UNIT;
pc->c[1] = 0x17;
- memset(pc->buffer, 0, 12);
- pc->buffer[1] = 0xA2;
+ memset(pc->buf, 0, 12);
+ pc->buf[1] = 0xA2;
/* Default format list header, u8 1: FOV/DCRT/IMM bits set */
if (flags & 1) /* Verify bit on... */
- pc->buffer[1] ^= 0x20; /* ... turn off DCRT bit */
- pc->buffer[3] = 8;
+ pc->buf[1] ^= 0x20; /* ... turn off DCRT bit */
+ pc->buf[3] = 8;
- put_unaligned(htonl(b), (unsigned int *)(&pc->buffer[4]));
- put_unaligned(htonl(l), (unsigned int *)(&pc->buffer[8]));
- pc->buffer_size=12;
- set_bit(PC_WRITING, &pc->flags);
+ put_unaligned(cpu_to_be32(b), (unsigned int *)(&pc->buf[4]));
+ put_unaligned(cpu_to_be32(l), (unsigned int *)(&pc->buf[8]));
+ pc->buf_size = 12;
+ pc->flags |= PC_FLAG_WRITING;
}
-/*
- * A mode sense command is used to "sense" floppy parameters.
- */
-static void idefloppy_create_mode_sense_cmd (idefloppy_pc_t *pc, u8 page_code, u8 type)
+/* A mode sense command is used to "sense" floppy parameters. */
+static void idefloppy_create_mode_sense_cmd(struct ide_atapi_pc *pc,
+ u8 page_code, u8 type)
{
- u16 length = sizeof(idefloppy_mode_parameter_header_t);
-
+ u16 length = 8; /* sizeof(Mode Parameter Header) = 8 Bytes */
+
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_MODE_SENSE_CMD;
+ pc->c[0] = GPCMD_MODE_SENSE_10;
pc->c[1] = 0;
pc->c[2] = page_code + (type << 6);
switch (page_code) {
- case IDEFLOPPY_CAPABILITIES_PAGE:
- length += 12;
- break;
- case IDEFLOPPY_FLEXIBLE_DISK_PAGE:
- length += 32;
- break;
- default:
- printk(KERN_ERR "ide-floppy: unsupported page code "
+ case IDEFLOPPY_CAPABILITIES_PAGE:
+ length += 12;
+ break;
+ case IDEFLOPPY_FLEXIBLE_DISK_PAGE:
+ length += 32;
+ break;
+ default:
+ printk(KERN_ERR "ide-floppy: unsupported page code "
"in create_mode_sense_cmd\n");
}
- put_unaligned(htons(length), (u16 *) &pc->c[7]);
- pc->request_transfer = length;
+ put_unaligned(cpu_to_be16(length), (u16 *) &pc->c[7]);
+ pc->req_xfer = length;
}
-static void idefloppy_create_start_stop_cmd (idefloppy_pc_t *pc, int start)
+static void idefloppy_create_start_stop_cmd(struct ide_atapi_pc *pc, int start)
{
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_START_STOP_CMD;
+ pc->c[0] = GPCMD_START_STOP_UNIT;
pc->c[4] = start;
}
-static void idefloppy_create_test_unit_ready_cmd(idefloppy_pc_t *pc)
+static void idefloppy_create_test_unit_ready_cmd(struct ide_atapi_pc *pc)
{
idefloppy_init_pc(pc);
- pc->c[0] = IDEFLOPPY_TEST_UNIT_READY_CMD;
+ pc->c[0] = GPCMD_TEST_UNIT_READY;
}
-static void idefloppy_create_rw_cmd (idefloppy_floppy_t *floppy, idefloppy_pc_t *pc, struct request *rq, unsigned long sector)
+static void idefloppy_create_rw_cmd(idefloppy_floppy_t *floppy,
+ struct ide_atapi_pc *pc, struct request *rq,
+ unsigned long sector)
{
int block = sector / floppy->bs_factor;
int blocks = rq->nr_sectors / floppy->bs_factor;
int cmd = rq_data_dir(rq);
- debug_log("create_rw1%d_cmd: block == %d, blocks == %d\n",
- 2 * test_bit (IDEFLOPPY_USE_READ12, &floppy->flags),
+ debug_log("create_rw10_cmd: block == %d, blocks == %d\n",
block, blocks);
idefloppy_init_pc(pc);
- if (test_bit(IDEFLOPPY_USE_READ12, &floppy->flags)) {
- pc->c[0] = cmd == READ ? IDEFLOPPY_READ12_CMD : IDEFLOPPY_WRITE12_CMD;
- put_unaligned(htonl(blocks), (unsigned int *) &pc->c[6]);
- } else {
- pc->c[0] = cmd == READ ? IDEFLOPPY_READ10_CMD : IDEFLOPPY_WRITE10_CMD;
- put_unaligned(htons(blocks), (unsigned short *) &pc->c[7]);
- }
- put_unaligned(htonl(block), (unsigned int *) &pc->c[2]);
- pc->callback = &idefloppy_rw_callback;
+ pc->c[0] = cmd == READ ? GPCMD_READ_10 : GPCMD_WRITE_10;
+ put_unaligned(cpu_to_be16(blocks), (unsigned short *)&pc->c[7]);
+ put_unaligned(cpu_to_be32(block), (unsigned int *) &pc->c[2]);
+
+ pc->idefloppy_callback = &idefloppy_rw_callback;
pc->rq = rq;
pc->b_count = cmd == READ ? 0 : rq->bio->bi_size;
- if (rq->flags & REQ_RW)
- set_bit(PC_WRITING, &pc->flags);
- pc->buffer = NULL;
- pc->request_transfer = pc->buffer_size = blocks * floppy->block_size;
- set_bit(PC_DMA_RECOMMENDED, &pc->flags);
+ if (rq->cmd_flags & REQ_RW)
+ pc->flags |= PC_FLAG_WRITING;
+ pc->buf = NULL;
+ pc->req_xfer = pc->buf_size = blocks * floppy->block_size;
+ pc->flags |= PC_FLAG_DMA_RECOMMENDED;
}
-static int
-idefloppy_blockpc_cmd(idefloppy_floppy_t *floppy, idefloppy_pc_t *pc, struct request *rq)
+static void idefloppy_blockpc_cmd(idefloppy_floppy_t *floppy,
+ struct ide_atapi_pc *pc, struct request *rq)
{
- /*
- * just support eject for now, it would not be hard to make the
- * REQ_BLOCK_PC support fully-featured
- */
- if (rq->cmd[0] != IDEFLOPPY_START_STOP_CMD)
- return 1;
-
idefloppy_init_pc(pc);
+ pc->idefloppy_callback = &idefloppy_rw_callback;
memcpy(pc->c, rq->cmd, sizeof(pc->c));
- return 0;
+ pc->rq = rq;
+ pc->b_count = rq->data_len;
+ if (rq->data_len && rq_data_dir(rq) == WRITE)
+ pc->flags |= PC_FLAG_WRITING;
+ pc->buf = rq->data;
+ if (rq->bio)
+ pc->flags |= PC_FLAG_DMA_RECOMMENDED;
+ /*
+ * possibly problematic, doesn't look like ide-floppy correctly
+ * handled scattered requests if dma fails...
+ */
+ pc->req_xfer = pc->buf_size = rq->data_len;
}
-/*
- * idefloppy_do_request is our request handling function.
- */
-static ide_startstop_t idefloppy_do_request (ide_drive_t *drive, struct request *rq, sector_t block_s)
+static ide_startstop_t idefloppy_do_request(ide_drive_t *drive,
+ struct request *rq, sector_t block_s)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- idefloppy_pc_t *pc;
+ struct ide_atapi_pc *pc;
unsigned long block = (unsigned long)block_s;
- debug_log(KERN_INFO "rq_status: %d, dev: %s, flags: %lx, errors: %d\n",
- rq->rq_status,
- rq->rq_disk ? rq->rq_disk->disk_name ? "?",
- rq->flags, rq->errors);
- debug_log(KERN_INFO "sector: %ld, nr_sectors: %ld, "
+ debug_log("dev: %s, cmd_type: %x, errors: %d\n",
+ rq->rq_disk ? rq->rq_disk->disk_name : "?",
+ rq->cmd_type, rq->errors);
+ debug_log("sector: %ld, nr_sectors: %ld, "
"current_nr_sectors: %d\n", (long)rq->sector,
rq->nr_sectors, rq->current_nr_sectors);
if (rq->errors >= ERROR_MAX) {
- if (floppy->failed_pc != NULL) {
- if (idefloppy_should_report_error(floppy))
- printk(KERN_ERR "ide-floppy: %s: I/O error, pc = %2x,"
- " key = %2x, asc = %2x, ascq = %2x\n",
- drive->name, floppy->failed_pc->c[0],
- floppy->sense_key, floppy->asc, floppy->ascq);
- }
+ if (floppy->failed_pc)
+ ide_floppy_report_error(floppy, floppy->failed_pc);
else
printk(KERN_ERR "ide-floppy: %s: I/O error\n",
drive->name);
- idefloppy_do_end_request(drive, 0, 0);
+ idefloppy_end_request(drive, 0, 0);
return ide_stopped;
}
- if (rq->flags & REQ_CMD) {
+ if (blk_fs_request(rq)) {
if (((long)rq->sector % floppy->bs_factor) ||
(rq->nr_sectors % floppy->bs_factor)) {
- printk("%s: unsupported r/w request size\n",
- drive->name);
- idefloppy_do_end_request(drive, 0, 0);
+ printk(KERN_ERR "%s: unsupported r/w request size\n",
+ drive->name);
+ idefloppy_end_request(drive, 0, 0);
return ide_stopped;
}
pc = idefloppy_next_pc_storage(drive);
idefloppy_create_rw_cmd(floppy, pc, rq, block);
- } else if (rq->flags & REQ_SPECIAL) {
- pc = (idefloppy_pc_t *) rq->buffer;
- } else if (rq->flags & REQ_BLOCK_PC) {
+ } else if (blk_special_request(rq)) {
+ pc = (struct ide_atapi_pc *) rq->buffer;
+ } else if (blk_pc_request(rq)) {
pc = idefloppy_next_pc_storage(drive);
- if (idefloppy_blockpc_cmd(floppy, pc, rq)) {
- idefloppy_do_end_request(drive, 0, 0);
- return ide_stopped;
- }
+ idefloppy_blockpc_cmd(floppy, pc, rq);
} else {
blk_dump_rq_flags(rq,
"ide-floppy: unsupported command in queue");
- idefloppy_do_end_request(drive, 0, 0);
+ idefloppy_end_request(drive, 0, 0);
return ide_stopped;
}
}
/*
- * idefloppy_queue_pc_tail adds a special packet command request to the
- * tail of the request queue, and waits for it to be serviced.
+ * Add a special packet command request to the tail of the request queue,
+ * and wait for it to be serviced.
*/
-static int idefloppy_queue_pc_tail (ide_drive_t *drive,idefloppy_pc_t *pc)
+static int idefloppy_queue_pc_tail(ide_drive_t *drive, struct ide_atapi_pc *pc)
{
struct ide_floppy_obj *floppy = drive->driver_data;
struct request rq;
- ide_init_drive_cmd (&rq);
+ ide_init_drive_cmd(&rq);
rq.buffer = (char *) pc;
- rq.flags = REQ_SPECIAL; // rq.cmd = IDEFLOPPY_PC_RQ;
+ rq.cmd_type = REQ_TYPE_SPECIAL;
rq.rq_disk = floppy->disk;
return ide_do_drive_cmd(drive, &rq, ide_wait);
}
/*
- * Look at the flexible disk page parameters. We will ignore the CHS
- * capacity parameters and use the LBA parameters instead.
+ * Look at the flexible disk page parameters. We ignore the CHS capacity
+ * parameters and use the LBA parameters instead.
*/
-static int idefloppy_get_flexible_disk_page (ide_drive_t *drive)
+static int ide_floppy_get_flexible_disk_page(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- idefloppy_pc_t pc;
- idefloppy_mode_parameter_header_t *header;
- idefloppy_flexible_disk_page_t *page;
+ struct ide_atapi_pc pc;
+ u8 *page;
int capacity, lba_capacity;
+ u16 transfer_rate, sector_size, cyls, rpm;
+ u8 heads, sectors;
+
+ idefloppy_create_mode_sense_cmd(&pc, IDEFLOPPY_FLEXIBLE_DISK_PAGE,
+ MODE_SENSE_CURRENT);
- idefloppy_create_mode_sense_cmd(&pc, IDEFLOPPY_FLEXIBLE_DISK_PAGE, MODE_SENSE_CURRENT);
- if (idefloppy_queue_pc_tail(drive,&pc)) {
- printk(KERN_ERR "ide-floppy: Can't get flexible disk "
- "page parameters\n");
+ if (idefloppy_queue_pc_tail(drive, &pc)) {
+ printk(KERN_ERR "ide-floppy: Can't get flexible disk page"
+ " parameters\n");
return 1;
}
- header = (idefloppy_mode_parameter_header_t *) pc.buffer;
- floppy->wp = header->wp;
+ floppy->wp = !!(pc.buf[3] & 0x80);
set_disk_ro(floppy->disk, floppy->wp);
- page = (idefloppy_flexible_disk_page_t *) (header + 1);
-
- page->transfer_rate = ntohs(page->transfer_rate);
- page->sector_size = ntohs(page->sector_size);
- page->cyls = ntohs(page->cyls);
- page->rpm = ntohs(page->rpm);
- capacity = page->cyls * page->heads * page->sectors * page->sector_size;
- if (memcmp (page, &floppy->flexible_disk_page, sizeof (idefloppy_flexible_disk_page_t)))
+ page = &pc.buf[8];
+
+ transfer_rate = be16_to_cpu(*(u16 *)&pc.buf[8 + 2]);
+ sector_size = be16_to_cpu(*(u16 *)&pc.buf[8 + 6]);
+ cyls = be16_to_cpu(*(u16 *)&pc.buf[8 + 8]);
+ rpm = be16_to_cpu(*(u16 *)&pc.buf[8 + 28]);
+ heads = pc.buf[8 + 4];
+ sectors = pc.buf[8 + 5];
+
+ capacity = cyls * heads * sectors * sector_size;
+
+ if (memcmp(page, &floppy->flexible_disk_page, 32))
printk(KERN_INFO "%s: %dkB, %d/%d/%d CHS, %d kBps, "
"%d sector size, %d rpm\n",
- drive->name, capacity / 1024, page->cyls,
- page->heads, page->sectors,
- page->transfer_rate / 8, page->sector_size, page->rpm);
-
- floppy->flexible_disk_page = *page;
- drive->bios_cyl = page->cyls;
- drive->bios_head = page->heads;
- drive->bios_sect = page->sectors;
+ drive->name, capacity / 1024, cyls, heads,
+ sectors, transfer_rate / 8, sector_size, rpm);
+
+ memcpy(&floppy->flexible_disk_page, page, 32);
+ drive->bios_cyl = cyls;
+ drive->bios_head = heads;
+ drive->bios_sect = sectors;
lba_capacity = floppy->blocks * floppy->block_size;
+
if (capacity < lba_capacity) {
printk(KERN_NOTICE "%s: The disk reports a capacity of %d "
"bytes, but the drive only handles %d\n",
drive->name, lba_capacity, capacity);
- floppy->blocks = floppy->block_size ? capacity / floppy->block_size : 0;
+ floppy->blocks = floppy->block_size ?
+ capacity / floppy->block_size : 0;
}
return 0;
}
-static int idefloppy_get_capability_page(ide_drive_t *drive)
+static int idefloppy_get_sfrp_bit(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- idefloppy_pc_t pc;
- idefloppy_mode_parameter_header_t *header;
- idefloppy_capabilities_page_t *page;
+ struct ide_atapi_pc pc;
floppy->srfp = 0;
idefloppy_create_mode_sense_cmd(&pc, IDEFLOPPY_CAPABILITIES_PAGE,
MODE_SENSE_CURRENT);
- set_bit(PC_SUPPRESS_ERROR, &pc.flags);
- if (idefloppy_queue_pc_tail(drive,&pc)) {
+ pc.flags |= PC_FLAG_SUPPRESS_ERROR;
+ if (idefloppy_queue_pc_tail(drive, &pc))
return 1;
- }
- header = (idefloppy_mode_parameter_header_t *) pc.buffer;
- page= (idefloppy_capabilities_page_t *)(header+1);
- floppy->srfp = page->srfp;
+ floppy->srfp = pc.buf[8 + 2] & 0x40;
return (0);
}
/*
- * Determine if a media is present in the floppy drive, and if so,
- * its LBA capacity.
+ * Determine if a media is present in the floppy drive, and if so, its LBA
+ * capacity.
*/
-static int idefloppy_get_capacity (ide_drive_t *drive)
+static int ide_floppy_get_capacity(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- idefloppy_pc_t pc;
- idefloppy_capacity_header_t *header;
- idefloppy_capacity_descriptor_t *descriptor;
- int i, descriptors, rc = 1, blocks, length;
-
+ struct ide_atapi_pc pc;
+ u8 *cap_desc;
+ u8 header_len, desc_cnt;
+ int i, rc = 1, blocks, length;
+
drive->bios_cyl = 0;
drive->bios_head = drive->bios_sect = 0;
- floppy->blocks = floppy->bs_factor = 0;
+ floppy->blocks = 0;
+ floppy->bs_factor = 1;
set_capacity(floppy->disk, 0);
idefloppy_create_read_capacity_cmd(&pc);
printk(KERN_ERR "ide-floppy: Can't get floppy parameters\n");
return 1;
}
- header = (idefloppy_capacity_header_t *) pc.buffer;
- descriptors = header->length / sizeof(idefloppy_capacity_descriptor_t);
- descriptor = (idefloppy_capacity_descriptor_t *) (header + 1);
+ header_len = pc.buf[3];
+ cap_desc = &pc.buf[4];
+ desc_cnt = header_len / 8; /* capacity descriptor of 8 bytes */
+
+ for (i = 0; i < desc_cnt; i++) {
+ unsigned int desc_start = 4 + i*8;
+
+ blocks = be32_to_cpu(*(u32 *)&pc.buf[desc_start]);
+ length = be16_to_cpu(*(u16 *)&pc.buf[desc_start + 6]);
+
+ debug_log("Descriptor %d: %dkB, %d blocks, %d sector size\n",
+ i, blocks * length / 1024, blocks, length);
- for (i = 0; i < descriptors; i++, descriptor++) {
- blocks = descriptor->blocks = ntohl(descriptor->blocks);
- length = descriptor->length = ntohs(descriptor->length);
+ if (i)
+ continue;
+ /*
+ * the code below is valid only for the 1st descriptor, ie i=0
+ */
- if (!i)
- {
- switch (descriptor->dc) {
+ switch (pc.buf[desc_start + 4] & 0x03) {
/* Clik! drive returns this instead of CAPACITY_CURRENT */
case CAPACITY_UNFORMATTED:
- if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags))
- /*
+ if (!(floppy->flags & IDEFLOPPY_FLAG_CLIK_DRIVE))
+ /*
* If it is not a clik drive, break out
* (maintains previous driver behaviour)
*/
break;
case CAPACITY_CURRENT:
/* Normal Zip/LS-120 disks */
- if (memcmp(descriptor, &floppy->capacity, sizeof (idefloppy_capacity_descriptor_t)))
+ if (memcmp(cap_desc, &floppy->cap_desc, 8))
printk(KERN_INFO "%s: %dkB, %d blocks, %d "
"sector size\n", drive->name,
blocks * length / 1024, blocks, length);
- floppy->capacity = *descriptor;
+ memcpy(&floppy->cap_desc, cap_desc, 8);
+
if (!length || length % 512) {
printk(KERN_NOTICE "%s: %d bytes block size "
"not supported\n", drive->name, length);
} else {
- floppy->blocks = blocks;
- floppy->block_size = length;
- if ((floppy->bs_factor = length / 512) != 1)
- printk(KERN_NOTICE "%s: warning: non "
+ floppy->blocks = blocks;
+ floppy->block_size = length;
+ floppy->bs_factor = length / 512;
+ if (floppy->bs_factor != 1)
+ printk(KERN_NOTICE "%s: warning: non "
"512 bytes block size not "
"fully supported\n",
drive->name);
- rc = 0;
+ rc = 0;
}
break;
case CAPACITY_NO_CARTRIDGE:
"in drive\n", drive->name);
break;
}
- }
- if (!i) {
- debug_log( "Descriptor 0 Code: %d\n",
- descriptor->dc);
- }
- debug_log( "Descriptor %d: %dkB, %d blocks, %d "
- "sector size\n", i, blocks * length / 1024, blocks,
- length);
+ debug_log("Descriptor 0 Code: %d\n",
+ pc.buf[desc_start + 4] & 0x03);
}
/* Clik! disk does not support get_flexible_disk_page */
- if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
- (void) idefloppy_get_flexible_disk_page(drive);
- }
+ if (!(floppy->flags & IDEFLOPPY_FLAG_CLIK_DRIVE))
+ (void) ide_floppy_get_flexible_disk_page(drive);
set_capacity(floppy->disk, floppy->blocks * floppy->bs_factor);
return rc;
}
/*
-** Obtain the list of formattable capacities.
-** Very similar to idefloppy_get_capacity, except that we push the capacity
-** descriptors to userland, instead of our own structures.
-**
-** Userland gives us the following structure:
-**
-** struct idefloppy_format_capacities {
-** int nformats;
-** struct {
-** int nblocks;
-** int blocksize;
-** } formats[];
-** } ;
-**
-** userland initializes nformats to the number of allocated formats[]
-** records. On exit we set nformats to the number of records we've
-** actually initialized.
-**
-*/
-
-static int idefloppy_get_format_capacities(ide_drive_t *drive, int __user *arg)
+ * Obtain the list of formattable capacities.
+ * Very similar to ide_floppy_get_capacity, except that we push the capacity
+ * descriptors to userland, instead of our own structures.
+ *
+ * Userland gives us the following structure:
+ *
+ * struct idefloppy_format_capacities {
+ * int nformats;
+ * struct {
+ * int nblocks;
+ * int blocksize;
+ * } formats[];
+ * };
+ *
+ * userland initializes nformats to the number of allocated formats[] records.
+ * On exit we set nformats to the number of records we've actually initialized.
+ */
+
+static int ide_floppy_get_format_capacities(ide_drive_t *drive, int __user *arg)
{
- idefloppy_pc_t pc;
- idefloppy_capacity_header_t *header;
- idefloppy_capacity_descriptor_t *descriptor;
- int i, descriptors, blocks, length;
- int u_array_size;
- int u_index;
+ struct ide_atapi_pc pc;
+ u8 header_len, desc_cnt;
+ int i, blocks, length, u_array_size, u_index;
int __user *argp;
if (get_user(u_array_size, arg))
idefloppy_create_read_capacity_cmd(&pc);
if (idefloppy_queue_pc_tail(drive, &pc)) {
printk(KERN_ERR "ide-floppy: Can't get floppy parameters\n");
- return (-EIO);
- }
- header = (idefloppy_capacity_header_t *) pc.buffer;
- descriptors = header->length /
- sizeof(idefloppy_capacity_descriptor_t);
- descriptor = (idefloppy_capacity_descriptor_t *) (header + 1);
+ return (-EIO);
+ }
+ header_len = pc.buf[3];
+ desc_cnt = header_len / 8; /* capacity descriptor of 8 bytes */
u_index = 0;
argp = arg + 1;
/*
- ** We always skip the first capacity descriptor. That's the
- ** current capacity. We are interested in the remaining descriptors,
- ** the formattable capacities.
- */
+ * We always skip the first capacity descriptor. That's the current
+ * capacity. We are interested in the remaining descriptors, the
+ * formattable capacities.
+ */
+ for (i = 1; i < desc_cnt; i++) {
+ unsigned int desc_start = 4 + i*8;
- for (i=0; i<descriptors; i++, descriptor++) {
if (u_index >= u_array_size)
break; /* User-supplied buffer too small */
- if (i == 0)
- continue; /* Skip the first descriptor */
- blocks = ntohl(descriptor->blocks);
- length = ntohs(descriptor->length);
+ blocks = be32_to_cpu(*(u32 *)&pc.buf[desc_start]);
+ length = be16_to_cpu(*(u16 *)&pc.buf[desc_start + 6]);
if (put_user(blocks, argp))
return(-EFAULT);
}
/*
-** Send ATAPI_FORMAT_UNIT to the drive.
-**
-** Userland gives us the following structure:
-**
-** struct idefloppy_format_command {
-** int nblocks;
-** int blocksize;
-** int flags;
-** } ;
-**
-** flags is a bitmask, currently, the only defined flag is:
-**
-** 0x01 - verify media after format.
-*/
-
-static int idefloppy_begin_format(ide_drive_t *drive, int __user *arg)
-{
- int blocks;
- int length;
- int flags;
- idefloppy_pc_t pc;
-
- if (get_user(blocks, arg) ||
- get_user(length, arg+1) ||
- get_user(flags, arg+2)) {
- return (-EFAULT);
- }
-
- /* Get the SFRP bit */
- (void) idefloppy_get_capability_page(drive);
- idefloppy_create_format_unit_cmd(&pc, blocks, length, flags);
- if (idefloppy_queue_pc_tail(drive, &pc)) {
- return (-EIO);
- }
-
- return (0);
-}
-
-/*
-** Get ATAPI_FORMAT_UNIT progress indication.
-**
-** Userland gives a pointer to an int. The int is set to a progresss
-** indicator 0-65536, with 65536=100%.
-**
-** If the drive does not support format progress indication, we just check
-** the dsc bit, and return either 0 or 65536.
-*/
+ * Get ATAPI_FORMAT_UNIT progress indication.
+ *
+ * Userland gives a pointer to an int. The int is set to a progress
+ * indicator 0-65536, with 65536=100%.
+ *
+ * If the drive does not support format progress indication, we just check
+ * the dsc bit, and return either 0 or 65536.
+ */
static int idefloppy_get_format_progress(ide_drive_t *drive, int __user *arg)
{
idefloppy_floppy_t *floppy = drive->driver_data;
- idefloppy_pc_t pc;
+ struct ide_atapi_pc pc;
int progress_indication = 0x10000;
if (floppy->srfp) {
idefloppy_create_request_sense_cmd(&pc);
- if (idefloppy_queue_pc_tail(drive, &pc)) {
+ if (idefloppy_queue_pc_tail(drive, &pc))
return (-EIO);
- }
if (floppy->sense_key == 2 &&
floppy->asc == 4 &&
- floppy->ascq == 4) {
+ floppy->ascq == 4)
progress_indication = floppy->progress_indication;
- }
- /* Else assume format_unit has finished, and we're
- ** at 0x10000 */
+
+ /* Else assume format_unit has finished, and we're at 0x10000 */
} else {
- atapi_status_t status;
unsigned long flags;
+ u8 stat;
local_irq_save(flags);
- status.all = HWIF(drive)->INB(IDE_STATUS_REG);
+ stat = ide_read_status(drive);
local_irq_restore(flags);
- progress_indication = !status.b.dsc ? 0 : 0x10000;
+ progress_indication = ((stat & SEEK_STAT) == 0) ? 0 : 0x10000;
}
if (put_user(progress_indication, arg))
return (-EFAULT);
return (0);
}
-/*
- * Return the current floppy capacity.
- */
-static sector_t idefloppy_capacity (ide_drive_t *drive)
+static sector_t idefloppy_capacity(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
unsigned long capacity = floppy->blocks * floppy->bs_factor;
}
/*
- * idefloppy_identify_device checks if we can support a drive,
- * based on the ATAPI IDENTIFY command results.
+ * Check whether we can support a drive, based on the ATAPI IDENTIFY command
+ * results.
*/
-static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
+static int idefloppy_identify_device(ide_drive_t *drive, struct hd_driveid *id)
{
- struct idefloppy_id_gcw gcw;
-#if IDEFLOPPY_DEBUG_INFO
- u16 mask,i;
- char buffer[80];
-#endif /* IDEFLOPPY_DEBUG_INFO */
+ u8 gcw[2];
+ u8 device_type, protocol, removable, drq_type, packet_size;
*((u16 *) &gcw) = id->config;
+ device_type = gcw[1] & 0x1F;
+ removable = (gcw[0] & 0x80) >> 7;
+ protocol = (gcw[1] & 0xC0) >> 6;
+ drq_type = (gcw[0] & 0x60) >> 5;
+ packet_size = gcw[0] & 0x03;
+
#ifdef CONFIG_PPC
/* kludge for Apple PowerBook internal zip */
- if ((gcw.device_type == 5) &&
- !strstr(id->model, "CD-ROM") &&
- strstr(id->model, "ZIP"))
- gcw.device_type = 0;
+ if (device_type == 5 &&
+ !strstr(id->model, "CD-ROM") && strstr(id->model, "ZIP"))
+ device_type = 0;
#endif
-#if IDEFLOPPY_DEBUG_INFO
- printk(KERN_INFO "Dumping ATAPI Identify Device floppy parameters\n");
- switch (gcw.protocol) {
- case 0: case 1: sprintf(buffer, "ATA");break;
- case 2: sprintf(buffer, "ATAPI");break;
- case 3: sprintf(buffer, "Reserved (Unknown to ide-floppy)");break;
- }
- printk(KERN_INFO "Protocol Type: %s\n", buffer);
- switch (gcw.device_type) {
- case 0: sprintf(buffer, "Direct-access Device");break;
- case 1: sprintf(buffer, "Streaming Tape Device");break;
- case 2: case 3: case 4: sprintf (buffer, "Reserved");break;
- case 5: sprintf(buffer, "CD-ROM Device");break;
- case 6: sprintf(buffer, "Reserved");
- case 7: sprintf(buffer, "Optical memory Device");break;
- case 0x1f: sprintf(buffer, "Unknown or no Device type");break;
- default: sprintf(buffer, "Reserved");
- }
- printk(KERN_INFO "Device Type: %x - %s\n", gcw.device_type, buffer);
- printk(KERN_INFO "Removable: %s\n",gcw.removable ? "Yes":"No");
- switch (gcw.drq_type) {
- case 0: sprintf(buffer, "Microprocessor DRQ");break;
- case 1: sprintf(buffer, "Interrupt DRQ");break;
- case 2: sprintf(buffer, "Accelerated DRQ");break;
- case 3: sprintf(buffer, "Reserved");break;
- }
- printk(KERN_INFO "Command Packet DRQ Type: %s\n", buffer);
- switch (gcw.packet_size) {
- case 0: sprintf(buffer, "12 bytes");break;
- case 1: sprintf(buffer, "16 bytes");break;
- default: sprintf(buffer, "Reserved");break;
- }
- printk(KERN_INFO "Command Packet Size: %s\n", buffer);
- printk(KERN_INFO "Model: %.40s\n",id->model);
- printk(KERN_INFO "Firmware Revision: %.8s\n",id->fw_rev);
- printk(KERN_INFO "Serial Number: %.20s\n",id->serial_no);
- printk(KERN_INFO "Write buffer size(?): %d bytes\n",id->buf_size*512);
- printk(KERN_INFO "DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
- printk(KERN_INFO "LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
- printk(KERN_INFO "IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
- printk(KERN_INFO "IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
- printk(KERN_INFO "ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
- printk(KERN_INFO "PIO Cycle Timing Category: %d\n",id->tPIO);
- printk(KERN_INFO "DMA Cycle Timing Category: %d\n",id->tDMA);
- printk(KERN_INFO "Single Word DMA supported modes:\n");
- for (i=0,mask=1;i<8;i++,mask=mask << 1) {
- if (id->dma_1word & mask)
- printk(KERN_INFO " Mode %d%s\n", i,
- (id->dma_1word & (mask << 8)) ? " (active)" : "");
- }
- printk(KERN_INFO "Multi Word DMA supported modes:\n");
- for (i=0,mask=1;i<8;i++,mask=mask << 1) {
- if (id->dma_mword & mask)
- printk(KERN_INFO " Mode %d%s\n", i,
- (id->dma_mword & (mask << 8)) ? " (active)" : "");
- }
- if (id->field_valid & 0x0002) {
- printk(KERN_INFO "Enhanced PIO Modes: %s\n",
- id->eide_pio_modes & 1 ? "Mode 3":"None");
- if (id->eide_dma_min == 0)
- sprintf(buffer, "Not supported");
- else
- sprintf(buffer, "%d ns",id->eide_dma_min);
- printk(KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n", buffer);
- if (id->eide_dma_time == 0)
- sprintf(buffer, "Not supported");
- else
- sprintf(buffer, "%d ns",id->eide_dma_time);
- printk(KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n", buffer);
- if (id->eide_pio == 0)
- sprintf(buffer, "Not supported");
- else
- sprintf(buffer, "%d ns",id->eide_pio);
- printk(KERN_INFO "Minimum PIO cycle without IORDY: %s\n",
- buffer);
- if (id->eide_pio_iordy == 0)
- sprintf(buffer, "Not supported");
- else
- sprintf(buffer, "%d ns",id->eide_pio_iordy);
- printk(KERN_INFO "Minimum PIO cycle with IORDY: %s\n", buffer);
- } else
- printk(KERN_INFO "According to the device, fields 64-70 are not valid.\n");
-#endif /* IDEFLOPPY_DEBUG_INFO */
-
- if (gcw.protocol != 2)
- printk(KERN_ERR "ide-floppy: Protocol is not ATAPI\n");
- else if (gcw.device_type != 0)
- printk(KERN_ERR "ide-floppy: Device type is not set to floppy\n");
- else if (!gcw.removable)
+ if (protocol != 2)
+ printk(KERN_ERR "ide-floppy: Protocol (0x%02x) is not ATAPI\n",
+ protocol);
+ else if (device_type != 0)
+ printk(KERN_ERR "ide-floppy: Device type (0x%02x) is not set "
+ "to floppy\n", device_type);
+ else if (!removable)
printk(KERN_ERR "ide-floppy: The removable flag is not set\n");
- else if (gcw.drq_type == 3) {
- printk(KERN_ERR "ide-floppy: Sorry, DRQ type %d not supported\n", gcw.drq_type);
- } else if (gcw.packet_size != 0) {
- printk(KERN_ERR "ide-floppy: Packet size is not 12 bytes long\n");
- } else
+ else if (drq_type == 3)
+ printk(KERN_ERR "ide-floppy: Sorry, DRQ type (0x%02x) not "
+ "supported\n", drq_type);
+ else if (packet_size != 0)
+ printk(KERN_ERR "ide-floppy: Packet size (0x%02x) is not 12 "
+ "bytes\n", packet_size);
+ else
return 1;
return 0;
}
+#ifdef CONFIG_IDE_PROC_FS
static void idefloppy_add_settings(ide_drive_t *drive)
{
idefloppy_floppy_t *floppy = drive->driver_data;
-/*
- * drive setting name read/write ioctl ioctl data type min max mul_factor div_factor data pointer set function
- */
- ide_add_setting(drive, "bios_cyl", SETTING_RW, -1, -1, TYPE_INT, 0, 1023, 1, 1, &drive->bios_cyl, NULL);
- ide_add_setting(drive, "bios_head", SETTING_RW, -1, -1, TYPE_BYTE, 0, 255, 1, 1, &drive->bios_head, NULL);
- ide_add_setting(drive, "bios_sect", SETTING_RW, -1, -1, TYPE_BYTE, 0, 63, 1, 1, &drive->bios_sect, NULL);
- ide_add_setting(drive, "ticks", SETTING_RW, -1, -1, TYPE_BYTE, 0, 255, 1, 1, &floppy->ticks, NULL);
+ ide_add_setting(drive, "bios_cyl", SETTING_RW, TYPE_INT, 0, 1023, 1, 1,
+ &drive->bios_cyl, NULL);
+ ide_add_setting(drive, "bios_head", SETTING_RW, TYPE_BYTE, 0, 255, 1, 1,
+ &drive->bios_head, NULL);
+ ide_add_setting(drive, "bios_sect", SETTING_RW, TYPE_BYTE, 0, 63, 1, 1,
+ &drive->bios_sect, NULL);
+ ide_add_setting(drive, "ticks", SETTING_RW, TYPE_BYTE, 0, 255, 1, 1,
+ &floppy->ticks, NULL);
}
+#else
+static inline void idefloppy_add_settings(ide_drive_t *drive) { ; }
+#endif
-/*
- * Driver initialization.
- */
-static void idefloppy_setup (ide_drive_t *drive, idefloppy_floppy_t *floppy)
+static void idefloppy_setup(ide_drive_t *drive, idefloppy_floppy_t *floppy)
{
- struct idefloppy_id_gcw gcw;
+ u8 gcw[2];
*((u16 *) &gcw) = drive->id->config;
floppy->pc = floppy->pc_stack;
- if (gcw.drq_type == 1)
- set_bit(IDEFLOPPY_DRQ_INTERRUPT, &floppy->flags);
+
+ if (((gcw[0] & 0x60) >> 5) == 1)
+ floppy->flags |= IDEFLOPPY_FLAG_DRQ_INTERRUPT;
/*
- * We used to check revisions here. At this point however
- * I'm giving up. Just assume they are all broken, its easier.
+ * We used to check revisions here. At this point however I'm giving up.
+ * Just assume they are all broken, its easier.
*
- * The actual reason for the workarounds was likely
- * a driver bug after all rather than a firmware bug,
- * and the workaround below used to hide it. It should
- * be fixed as of version 1.9, but to be on the safe side
- * we'll leave the limitation below for the 2.2.x tree.
+ * The actual reason for the workarounds was likely a driver bug after
+ * all rather than a firmware bug, and the workaround below used to hide
+ * it. It should be fixed as of version 1.9, but to be on the safe side
+ * we'll leave the limitation below for the 2.2.x tree.
*/
-
if (!strncmp(drive->id->model, "IOMEGA ZIP 100 ATAPI", 20)) {
- set_bit(IDEFLOPPY_ZIP_DRIVE, &floppy->flags);
+ floppy->flags |= IDEFLOPPY_FLAG_ZIP_DRIVE;
/* This value will be visible in the /proc/ide/hdx/settings */
floppy->ticks = IDEFLOPPY_TICKS_DELAY;
blk_queue_max_sectors(drive->queue, 64);
}
/*
- * Guess what? The IOMEGA Clik! drive also needs the
- * above fix. It makes nasty clicking noises without
- * it, so please don't remove this.
- */
+ * Guess what? The IOMEGA Clik! drive also needs the above fix. It makes
+ * nasty clicking noises without it, so please don't remove this.
+ */
if (strncmp(drive->id->model, "IOMEGA Clik!", 11) == 0) {
blk_queue_max_sectors(drive->queue, 64);
- set_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags);
+ floppy->flags |= IDEFLOPPY_FLAG_CLIK_DRIVE;
}
-
- (void) idefloppy_get_capacity(drive);
+ (void) ide_floppy_get_capacity(drive);
idefloppy_add_settings(drive);
}
-static int ide_floppy_remove(struct device *dev)
+static void ide_floppy_remove(ide_drive_t *drive)
{
- ide_drive_t *drive = to_ide_device(dev);
idefloppy_floppy_t *floppy = drive->driver_data;
struct gendisk *g = floppy->disk;
- ide_unregister_subdriver(drive, floppy->driver);
+ ide_proc_unregister_driver(drive, floppy->driver);
del_gendisk(g);
ide_floppy_put(floppy);
-
- return 0;
}
-static void ide_floppy_release(struct kref *kref)
+static void idefloppy_cleanup_obj(struct kref *kref)
{
struct ide_floppy_obj *floppy = to_ide_floppy(kref);
ide_drive_t *drive = floppy->drive;
kfree(floppy);
}
-#ifdef CONFIG_PROC_FS
-
-static int proc_idefloppy_read_capacity
- (char *page, char **start, off_t off, int count, int *eof, void *data)
+#ifdef CONFIG_IDE_PROC_FS
+static int proc_idefloppy_read_capacity(char *page, char **start, off_t off,
+ int count, int *eof, void *data)
{
ide_drive_t*drive = (ide_drive_t *)data;
int len;
- len = sprintf(page,"%llu\n", (long long)idefloppy_capacity(drive));
- PROC_IDE_READ_RETURN(page,start,off,count,eof,len);
+ len = sprintf(page, "%llu\n", (long long)idefloppy_capacity(drive));
+ PROC_IDE_READ_RETURN(page, start, off, count, eof, len);
}
static ide_proc_entry_t idefloppy_proc[] = {
- { "capacity", S_IFREG|S_IRUGO, proc_idefloppy_read_capacity, NULL },
- { "geometry", S_IFREG|S_IRUGO, proc_ide_read_geometry, NULL },
+ { "capacity", S_IFREG|S_IRUGO, proc_idefloppy_read_capacity, NULL },
+ { "geometry", S_IFREG|S_IRUGO, proc_ide_read_geometry, NULL },
{ NULL, 0, NULL, NULL }
};
+#endif /* CONFIG_IDE_PROC_FS */
-#else
-
-#define idefloppy_proc NULL
-
-#endif /* CONFIG_PROC_FS */
-
-static int ide_floppy_probe(struct device *);
+static int ide_floppy_probe(ide_drive_t *);
static ide_driver_t idefloppy_driver = {
- .owner = THIS_MODULE,
.gen_driver = {
+ .owner = THIS_MODULE,
.name = "ide-floppy",
.bus = &ide_bus_type,
- .probe = ide_floppy_probe,
- .remove = ide_floppy_remove,
},
+ .probe = ide_floppy_probe,
+ .remove = ide_floppy_remove,
.version = IDEFLOPPY_VERSION,
.media = ide_floppy,
.supports_dsc_overlap = 0,
.do_request = idefloppy_do_request,
- .end_request = idefloppy_do_end_request,
+ .end_request = idefloppy_end_request,
.error = __ide_error,
.abort = __ide_abort,
+#ifdef CONFIG_IDE_PROC_FS
.proc = idefloppy_proc,
+#endif
};
static int idefloppy_open(struct inode *inode, struct file *filp)
struct gendisk *disk = inode->i_bdev->bd_disk;
struct ide_floppy_obj *floppy;
ide_drive_t *drive;
- idefloppy_pc_t pc;
+ struct ide_atapi_pc pc;
int ret = 0;
- debug_log(KERN_INFO "Reached idefloppy_open\n");
+ debug_log("Reached %s\n", __func__);
- if (!(floppy = ide_floppy_get(disk)))
+ floppy = ide_floppy_get(disk);
+ if (!floppy)
return -ENXIO;
drive = floppy->drive;
- drive->usage++;
+ floppy->openers++;
- if (drive->usage == 1) {
- clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
+ if (floppy->openers == 1) {
+ floppy->flags &= ~IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS;
/* Just in case */
idefloppy_create_test_unit_ready_cmd(&pc);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
- if (idefloppy_get_capacity (drive)
+ if (ide_floppy_get_capacity(drive)
&& (filp->f_flags & O_NDELAY) == 0
/*
- ** Allow O_NDELAY to open a drive without a disk, or with
- ** an unreadable disk, so that we can get the format
- ** capacity of the drive or begin the format - Sam
- */
+ * Allow O_NDELAY to open a drive without a disk, or with an
+ * unreadable disk, so that we can get the format capacity
+ * of the drive or begin the format - Sam
+ */
) {
- drive->usage--;
ret = -EIO;
goto out_put_floppy;
}
if (floppy->wp && (filp->f_mode & 2)) {
- drive->usage--;
ret = -EROFS;
goto out_put_floppy;
}
- set_bit(IDEFLOPPY_MEDIA_CHANGED, &floppy->flags);
+ floppy->flags |= IDEFLOPPY_FLAG_MEDIA_CHANGED;
/* IOMEGA Clik! drives do not support lock/unlock commands */
- if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
+ if (!(floppy->flags & IDEFLOPPY_FLAG_CLIK_DRIVE)) {
idefloppy_create_prevent_cmd(&pc, 1);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
check_disk_change(inode->i_bdev);
- } else if (test_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags)) {
- drive->usage--;
+ } else if (floppy->flags & IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS) {
ret = -EBUSY;
goto out_put_floppy;
}
return 0;
out_put_floppy:
+ floppy->openers--;
ide_floppy_put(floppy);
return ret;
}
struct gendisk *disk = inode->i_bdev->bd_disk;
struct ide_floppy_obj *floppy = ide_floppy_g(disk);
ide_drive_t *drive = floppy->drive;
- idefloppy_pc_t pc;
-
- debug_log(KERN_INFO "Reached idefloppy_release\n");
+ struct ide_atapi_pc pc;
+
+ debug_log("Reached %s\n", __func__);
- if (drive->usage == 1) {
+ if (floppy->openers == 1) {
/* IOMEGA Clik! drives do not support lock/unlock commands */
- if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
+ if (!(floppy->flags & IDEFLOPPY_FLAG_CLIK_DRIVE)) {
idefloppy_create_prevent_cmd(&pc, 0);
(void) idefloppy_queue_pc_tail(drive, &pc);
}
- clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
+ floppy->flags &= ~IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS;
}
- drive->usage--;
+
+ floppy->openers--;
ide_floppy_put(floppy);
return 0;
}
+static int idefloppy_getgeo(struct block_device *bdev, struct hd_geometry *geo)
+{
+ struct ide_floppy_obj *floppy = ide_floppy_g(bdev->bd_disk);
+ ide_drive_t *drive = floppy->drive;
+
+ geo->heads = drive->bios_head;
+ geo->sectors = drive->bios_sect;
+ geo->cylinders = (u16)drive->bios_cyl; /* truncate */
+ return 0;
+}
+
+static int ide_floppy_lockdoor(idefloppy_floppy_t *floppy,
+ struct ide_atapi_pc *pc, unsigned long arg, unsigned int cmd)
+{
+ if (floppy->openers > 1)
+ return -EBUSY;
+
+ /* The IOMEGA Clik! Drive doesn't support this command -
+ * no room for an eject mechanism */
+ if (!(floppy->flags & IDEFLOPPY_FLAG_CLIK_DRIVE)) {
+ int prevent = arg ? 1 : 0;
+
+ if (cmd == CDROMEJECT)
+ prevent = 0;
+
+ idefloppy_create_prevent_cmd(pc, prevent);
+ (void) idefloppy_queue_pc_tail(floppy->drive, pc);
+ }
+
+ if (cmd == CDROMEJECT) {
+ idefloppy_create_start_stop_cmd(pc, 2);
+ (void) idefloppy_queue_pc_tail(floppy->drive, pc);
+ }
+
+ return 0;
+}
+
+static int ide_floppy_format_unit(idefloppy_floppy_t *floppy,
+ int __user *arg)
+{
+ int blocks, length, flags, err = 0;
+ struct ide_atapi_pc pc;
+
+ if (floppy->openers > 1) {
+ /* Don't format if someone is using the disk */
+ floppy->flags &= ~IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS;
+ return -EBUSY;
+ }
+
+ floppy->flags |= IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS;
+
+ /*
+ * Send ATAPI_FORMAT_UNIT to the drive.
+ *
+ * Userland gives us the following structure:
+ *
+ * struct idefloppy_format_command {
+ * int nblocks;
+ * int blocksize;
+ * int flags;
+ * } ;
+ *
+ * flags is a bitmask, currently, the only defined flag is:
+ *
+ * 0x01 - verify media after format.
+ */
+ if (get_user(blocks, arg) ||
+ get_user(length, arg+1) ||
+ get_user(flags, arg+2)) {
+ err = -EFAULT;
+ goto out;
+ }
+
+ (void) idefloppy_get_sfrp_bit(floppy->drive);
+ idefloppy_create_format_unit_cmd(&pc, blocks, length, flags);
+
+ if (idefloppy_queue_pc_tail(floppy->drive, &pc))
+ err = -EIO;
+
+out:
+ if (err)
+ floppy->flags &= ~IDEFLOPPY_FLAG_FORMAT_IN_PROGRESS;
+ return err;
+}
+
+
static int idefloppy_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
struct block_device *bdev = inode->i_bdev;
struct ide_floppy_obj *floppy = ide_floppy_g(bdev->bd_disk);
ide_drive_t *drive = floppy->drive;
+ struct ide_atapi_pc pc;
void __user *argp = (void __user *)arg;
int err;
- int prevent = (arg) ? 1 : 0;
- idefloppy_pc_t pc;
switch (cmd) {
case CDROMEJECT:
- prevent = 0;
/* fall through */
case CDROM_LOCKDOOR:
- if (drive->usage > 1)
- return -EBUSY;
-
- /* The IOMEGA Clik! Drive doesn't support this command - no room for an eject mechanism */
- if (!test_bit(IDEFLOPPY_CLIK_DRIVE, &floppy->flags)) {
- idefloppy_create_prevent_cmd(&pc, prevent);
- (void) idefloppy_queue_pc_tail(drive, &pc);
- }
- if (cmd == CDROMEJECT) {
- idefloppy_create_start_stop_cmd(&pc, 2);
- (void) idefloppy_queue_pc_tail(drive, &pc);
- }
- return 0;
+ return ide_floppy_lockdoor(floppy, &pc, arg, cmd);
case IDEFLOPPY_IOCTL_FORMAT_SUPPORTED:
return 0;
case IDEFLOPPY_IOCTL_FORMAT_GET_CAPACITY:
- return idefloppy_get_format_capacities(drive, argp);
+ return ide_floppy_get_format_capacities(drive, argp);
case IDEFLOPPY_IOCTL_FORMAT_START:
-
if (!(file->f_mode & 2))
return -EPERM;
- if (drive->usage > 1) {
- /* Don't format if someone is using the disk */
-
- clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS,
- &floppy->flags);
- return -EBUSY;
- }
-
- set_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
-
- err = idefloppy_begin_format(drive, argp);
- if (err)
- clear_bit(IDEFLOPPY_FORMAT_IN_PROGRESS, &floppy->flags);
- return err;
- /*
- ** Note, the bit will be cleared when the device is
- ** closed. This is the cleanest way to handle the
- ** situation where the drive does not support
- ** format progress reporting.
- */
+ return ide_floppy_format_unit(floppy, (int __user *)arg);
case IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS:
return idefloppy_get_format_progress(drive, argp);
}
- return generic_ide_ioctl(drive, file, bdev, cmd, arg);
+
+ /*
+ * skip SCSI_IOCTL_SEND_COMMAND (deprecated)
+ * and CDROM_SEND_PACKET (legacy) ioctls
+ */
+ if (cmd != CDROM_SEND_PACKET && cmd != SCSI_IOCTL_SEND_COMMAND)
+ err = scsi_cmd_ioctl(file, bdev->bd_disk->queue,
+ bdev->bd_disk, cmd, argp);
+ else
+ err = -ENOTTY;
+
+ if (err == -ENOTTY)
+ err = generic_ide_ioctl(drive, file, bdev, cmd, arg);
+
+ return err;
}
static int idefloppy_media_changed(struct gendisk *disk)
{
struct ide_floppy_obj *floppy = ide_floppy_g(disk);
ide_drive_t *drive = floppy->drive;
+ int ret;
/* do not scan partitions twice if this is a removable device */
if (drive->attach) {
drive->attach = 0;
return 0;
}
- return test_and_clear_bit(IDEFLOPPY_MEDIA_CHANGED, &floppy->flags);
+ ret = !!(floppy->flags & IDEFLOPPY_FLAG_MEDIA_CHANGED);
+ floppy->flags &= ~IDEFLOPPY_FLAG_MEDIA_CHANGED;
+ return ret;
}
static int idefloppy_revalidate_disk(struct gendisk *disk)
}
static struct block_device_operations idefloppy_ops = {
- .owner = THIS_MODULE,
- .open = idefloppy_open,
- .release = idefloppy_release,
- .ioctl = idefloppy_ioctl,
- .media_changed = idefloppy_media_changed,
- .revalidate_disk= idefloppy_revalidate_disk
+ .owner = THIS_MODULE,
+ .open = idefloppy_open,
+ .release = idefloppy_release,
+ .ioctl = idefloppy_ioctl,
+ .getgeo = idefloppy_getgeo,
+ .media_changed = idefloppy_media_changed,
+ .revalidate_disk = idefloppy_revalidate_disk
};
-static int ide_floppy_probe(struct device *dev)
+static int ide_floppy_probe(ide_drive_t *drive)
{
- ide_drive_t *drive = to_ide_device(dev);
idefloppy_floppy_t *floppy;
struct gendisk *g;
goto failed;
if (drive->media != ide_floppy)
goto failed;
- if (!idefloppy_identify_device (drive, drive->id)) {
- printk (KERN_ERR "ide-floppy: %s: not supported by this version of ide-floppy\n", drive->name);
+ if (!idefloppy_identify_device(drive, drive->id)) {
+ printk(KERN_ERR "ide-floppy: %s: not supported by this version"
+ " of ide-floppy\n", drive->name);
goto failed;
}
if (drive->scsi) {
- printk("ide-floppy: passing drive %s to ide-scsi emulation.\n", drive->name);
+ printk(KERN_INFO "ide-floppy: passing drive %s to ide-scsi"
+ " emulation.\n", drive->name);
goto failed;
}
- if ((floppy = (idefloppy_floppy_t *) kzalloc (sizeof (idefloppy_floppy_t), GFP_KERNEL)) == NULL) {
- printk (KERN_ERR "ide-floppy: %s: Can't allocate a floppy structure\n", drive->name);
+ floppy = kzalloc(sizeof(idefloppy_floppy_t), GFP_KERNEL);
+ if (!floppy) {
+ printk(KERN_ERR "ide-floppy: %s: Can't allocate a floppy"
+ " structure\n", drive->name);
goto failed;
}
ide_init_disk(g, drive);
- ide_register_subdriver(drive, &idefloppy_driver);
+ ide_proc_register_driver(drive, &idefloppy_driver);
kref_init(&floppy->kref);
drive->driver_data = floppy;
- idefloppy_setup (drive, floppy);
+ idefloppy_setup(drive, floppy);
g->minors = 1 << PARTN_BITS;
g->driverfs_dev = &drive->gendev;
- strcpy(g->devfs_name, drive->devfs_name);
g->flags = drive->removable ? GENHD_FL_REMOVABLE : 0;
g->fops = &idefloppy_ops;
drive->attach = 1;
return -ENODEV;
}
-MODULE_DESCRIPTION("ATAPI FLOPPY Driver");
-
-static void __exit idefloppy_exit (void)
+static void __exit idefloppy_exit(void)
{
driver_unregister(&idefloppy_driver.gen_driver);
}
-/*
- * idefloppy_init will register the driver for each floppy.
- */
-static int idefloppy_init (void)
+static int __init idefloppy_init(void)
{
printk("ide-floppy driver " IDEFLOPPY_VERSION "\n");
return driver_register(&idefloppy_driver.gen_driver);
}
+MODULE_ALIAS("ide:*m-floppy*");
module_init(idefloppy_init);
module_exit(idefloppy_exit);
MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("ATAPI FLOPPY Driver");
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff