mv643xx_eth: fix unicast address filter corruption on mtu change

[safe/jmp/linux-2.6] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index e6857e0..e072903 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -46,7 +46,7 @@ menuconfig IDE
          SMART parameters from disk drives.
 
          To compile this driver as a module, choose M here: the
-         module will be called ide.
+         module will be called ide-core.ko.
 
          For further information, please read <file:Documentation/ide/ide.txt>.
 
@@ -62,6 +62,9 @@ config IDE_TIMINGS
 config IDE_ATAPI
        bool
 
+config IDE_LEGACY
+       bool
+
 config BLK_DEV_IDE_SATA
        bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
        default n
@@ -134,6 +137,7 @@ config BLK_DEV_DELKIN
 
 config BLK_DEV_IDECD
        tristate "Include IDE/ATAPI CDROM support"
+       select IDE_ATAPI
        ---help---
          If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
          a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
@@ -182,23 +186,6 @@ config BLK_DEV_IDETAPE
          To compile this driver as a module, choose M here: the
          module will be called ide-tape.
 
-config BLK_DEV_IDESCSI
-       tristate "SCSI emulation support (DEPRECATED)"
-       depends on SCSI
-       select IDE_ATAPI
-       ---help---
-         WARNING: ide-scsi is no longer needed for cd writing applications!
-         The 2.6 kernel supports direct writing to ide-cd, which eliminates
-         the need for ide-scsi + the entire scsi stack just for writing a
-         cd. The new method is more efficient in every way.
-
-         This will provide SCSI host adapter emulation for IDE ATAPI devices,
-         and will allow you to use a SCSI device driver instead of a native
-         ATAPI driver.
-
-         If both this SCSI emulation and native ATAPI support are compiled
-         into the kernel, the native support will be used.
-
 config BLK_DEV_IDEACPI
        bool "IDE ACPI support"
        depends on ACPI
@@ -478,6 +465,16 @@ config BLK_DEV_CS5535
 
          It is safe to say Y to this question.
 
+config BLK_DEV_CS5536
+       tristate "CS5536 chipset support"
+       depends on X86_32
+       select BLK_DEV_IDEDMA_PCI
+       help
+         This option enables support for the AMD CS5536
+         companion chip used with the Geode LX processor family.
+
+         If unsure, say N.
+
 config BLK_DEV_HPT366
        tristate "HPT36X/37X chipset support"
        select BLK_DEV_IDEDMA_PCI
@@ -524,6 +521,13 @@ config BLK_DEV_PIIX
          This allows the kernel to change PIO, DMA and UDMA speeds and to
          configure the chip to optimum performance.
 
+config BLK_DEV_IT8172
+       tristate "IT8172 IDE support"
+       select BLK_DEV_IDEDMA_PCI
+       help
+         This driver adds support for the IDE controller on the
+         IT8172 System Controller.
+
 config BLK_DEV_IT8213
        tristate "IT8213 IDE support"
        select BLK_DEV_IDEDMA_PCI
@@ -707,11 +711,6 @@ config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
        depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
 endchoice
 
-config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
-       int "Maximum transfer size (KB) per request (up to 128)"
-       default "128"
-       depends on BLK_DEV_IDE_AU1XXX
-
 config BLK_DEV_IDE_TX4938
        tristate "TX4938 internal IDE support"
        depends on SOC_TX4938
@@ -724,7 +723,7 @@ config BLK_DEV_IDE_TX4939
 
 config IDE_ARM
        tristate "ARM IDE support"
-       depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+       depends on ARM && (ARCH_RPC || ARCH_SHARK)
        default y
 
 config BLK_DEV_IDE_ICSIDE
@@ -856,6 +855,7 @@ config BLK_DEV_4DRIVES
 config BLK_DEV_ALI14XX
        tristate "ALI M14xx support"
        select IDE_TIMINGS
+       select IDE_LEGACY
        help
          This driver is enabled at runtime using the "ali14xx.probe" kernel
          boot parameter.  It enables support for the secondary IDE interface
@@ -866,6 +866,7 @@ config BLK_DEV_ALI14XX
 
 config BLK_DEV_DTC2278
        tristate "DTC-2278 support"
+       select IDE_LEGACY
        help
          This driver is enabled at runtime using the "dtc2278.probe" kernel
          boot parameter. It enables support for the secondary IDE interface
@@ -876,6 +877,7 @@ config BLK_DEV_DTC2278
 config BLK_DEV_HT6560B
        tristate "Holtek HT6560B support"
        select IDE_TIMINGS
+       select IDE_LEGACY
        help
          This driver is enabled at runtime using the "ht6560b.probe" kernel
          boot parameter. It enables support for the secondary IDE interface
@@ -886,6 +888,7 @@ config BLK_DEV_HT6560B
 config BLK_DEV_QD65XX
        tristate "QDI QD65xx support"
        select IDE_TIMINGS
+       select IDE_LEGACY
        help
          This driver is enabled at runtime using the "qd65xx.probe" kernel
          boot parameter.  It permits faster I/O speeds to be set.  See the
@@ -894,6 +897,7 @@ config BLK_DEV_QD65XX
 
 config BLK_DEV_UMC8672
        tristate "UMC-8672 support"
+       select IDE_LEGACY
        help
          This driver is enabled at runtime using the "umc8672.probe" kernel
          boot parameter. It enables support for the secondary IDE interface