bool
menuconfig IDE
- tristate "ATA/ATAPI/MFM/RLL support"
+ tristate "ATA/ATAPI/MFM/RLL support (DEPRECATED)"
depends on HAVE_IDE
depends on BLOCK
---help---
- If you say Y here, your kernel will be able to manage low cost mass
- storage units such as ATA/(E)IDE and ATAPI units. The most common
- cases are IDE hard drives and ATAPI CD-ROM drives.
-
- If your system is pure SCSI and doesn't use these interfaces, you
- can say N here.
-
- Integrated Disk Electronics (IDE aka ATA-1) is a connecting standard
- for mass storage units such as hard disks. It was designed by
- Western Digital and Compaq Computer in 1984. It was then named
- ST506. Quite a number of disks use the IDE interface.
-
- AT Attachment (ATA) is the superset of the IDE specifications.
- ST506 was also called ATA-1.
-
- Fast-IDE is ATA-2 (also named Fast ATA), Enhanced IDE (EIDE) is
- ATA-3. It provides support for larger disks (up to 8.4GB by means of
- the LBA standard), more disks (4 instead of 2) and for other mass
- storage units such as tapes and cdrom. UDMA/33 (aka UltraDMA/33) is
- ATA-4 and provides faster (and more CPU friendly) transfer modes
- than previous PIO (Programmed processor Input/Output) from previous
- ATA/IDE standards by means of fast DMA controllers.
-
- ATA Packet Interface (ATAPI) is a protocol used by EIDE tape and
- CD-ROM drives, similar in many respects to the SCSI protocol.
-
- SMART IDE (Self Monitoring, Analysis and Reporting Technology) was
- designed in order to prevent data corruption and disk crash by
- detecting pre hardware failure conditions (heat, access time, and
- the like...). Disks built since June 1995 may follow this standard.
- The kernel itself doesn't manage this; however there are quite a
- number of user programs such as smart that can query the status of
- SMART parameters from disk drives.
+ If you say Y here, your kernel will be able to manage ATA/(E)IDE and
+ ATAPI units. The most common cases are IDE hard drives and ATAPI
+ CD-ROM drives.
+
+ This subsystem is currently in maintenance mode with only bug fix
+ changes applied. Users of ATA hardware are encouraged to migrate to
+ the newer ATA subsystem ("Serial ATA (prod) and Parallel ATA
+ (experimental) drivers") which is more actively maintained.
To compile this driver as a module, choose M here: the
- module will be called ide.
+ module will be called ide-core.
For further information, please read <file:Documentation/ide/ide.txt>.
- If unsure, say Y.
+ If unsure, say N.
if IDE
comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
+config IDE_XFER_MODE
+ bool
+
config IDE_TIMINGS
bool
+ select IDE_XFER_MODE
config IDE_ATAPI
bool
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
+ select IDE_ATAPI
---help---
If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
To compile this driver as a module, choose M here: the
module will be called ide-tape.
-config BLK_DEV_IDESCSI
- tristate "SCSI emulation support (DEPRECATED)"
- depends on SCSI
- select IDE_ATAPI
- ---help---
- WARNING: ide-scsi is no longer needed for cd writing applications!
- The 2.6 kernel supports direct writing to ide-cd, which eliminates
- the need for ide-scsi + the entire scsi stack just for writing a
- cd. The new method is more efficient in every way.
-
- This will provide SCSI host adapter emulation for IDE ATAPI devices,
- and will allow you to use a SCSI device driver instead of a native
- ATAPI driver.
-
- If both this SCSI emulation and native ATAPI support are compiled
- into the kernel, the native support will be used.
-
config BLK_DEV_IDEACPI
bool "IDE ACPI support"
depends on ACPI
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- depends on ALPHA || X86 || IA64 || M32R || MIPS
+ depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC || ARCH_SHARK
+ default ARM && (ARCH_RPC || ARCH_SHARK)
help
This is the generic IDE driver. This driver attaches to the
fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and
It is safe to say Y to this question.
+config BLK_DEV_CS5536
+ tristate "CS5536 chipset support"
+ depends on X86_32
+ select BLK_DEV_IDEDMA_PCI
+ help
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
+
+ If unsure, say N.
+
config BLK_DEV_HPT366
tristate "HPT36X/37X chipset support"
select BLK_DEV_IDEDMA_PCI
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
+config BLK_DEV_IT8172
+ tristate "IT8172 IDE support"
+ select BLK_DEV_IDEDMA_PCI
+ help
+ This driver adds support for the IDE controller on the
+ IT8172 System Controller.
+
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
select BLK_DEV_IDEDMA_PCI
# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
- depends on PPC_PMAC && IDE=y
+ depends on PPC_PMAC
select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
config BLK_DEV_IDE_AU1XXX
bool "IDE for AMD Alchemy Au1200"
depends on SOC_AU1200
+ select IDE_XFER_MODE
choice
prompt "IDE Mode for AMD Alchemy Au1200"
default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
endchoice
-config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
- int "Maximum transfer size (KB) per request (up to 128)"
- default "128"
- depends on BLK_DEV_IDE_AU1XXX
-
config BLK_DEV_IDE_TX4938
tristate "TX4938 internal IDE support"
depends on SOC_TX4938
depends on SOC_TX4939
select BLK_DEV_IDEDMA_SFF
-config IDE_ARM
- tristate "ARM IDE support"
- depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
- default y
+config BLK_DEV_IDE_AT91
+ tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
+ depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
+ select IDE_TIMINGS
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
This includes on-board IDE interfaces on some Amiga models (A600,
A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
bus (M-Tech E-Matrix 530 expansion card).
- Say Y if you have an Amiga with a Gayle IDE interface and want to use
- IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
- it.
- Note that you also have to enable Zorro bus support if you want to
- use Gayle IDE interfaces on the Zorro expansion bus.
-config BLK_DEV_IDEDOUBLER
- bool "Amiga IDE Doubler support (EXPERIMENTAL)"
- depends on BLK_DEV_GAYLE && EXPERIMENTAL
- ---help---
- This feature provides support for the so-called `IDE doublers' (made
+ It also provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to
the on-board IDE interface of some Amiga models. Using such an IDE
doubler, you can connect up to four instead of two IDE devices to
- the Amiga's on-board IDE interface.
+ the Amiga's on-board IDE interface. The feature is enabled at kernel
+ runtime using the "gayle.doubler" kernel boot parameter.
- Note that the normal Amiga Gayle IDE driver may not work correctly
- if you have an IDE doubler and don't enable this feature!
+ Say Y if you have an Amiga with a Gayle IDE interface and want to use
+ IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
+ it.
- Say Y if you have an IDE doubler. The feature is enabled at kernel
- runtime using the "gayle.doubler" kernel boot parameter.
+ Note that you also have to enable Zorro bus support if you want to
+ use Gayle IDE interfaces on the Zorro expansion bus.
config BLK_DEV_BUDDHA
tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
+ select IDE_XFER_MODE
select IDE_LEGACY
help
This driver is enabled at runtime using the "dtc2278.probe" kernel
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
+ select IDE_XFER_MODE
select IDE_LEGACY
help
This driver is enabled at runtime using the "umc8672.probe" kernel
config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_SFF || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ select IDE_XFER_MODE
endif # IDE