bool
menuconfig IDE
- tristate "ATA/ATAPI/MFM/RLL support"
+ tristate "ATA/ATAPI/MFM/RLL support (DEPRECATED)"
depends on HAVE_IDE
depends on BLOCK
---help---
- If you say Y here, your kernel will be able to manage low cost mass
- storage units such as ATA/(E)IDE and ATAPI units. The most common
- cases are IDE hard drives and ATAPI CD-ROM drives.
-
- If your system is pure SCSI and doesn't use these interfaces, you
- can say N here.
-
- Integrated Disk Electronics (IDE aka ATA-1) is a connecting standard
- for mass storage units such as hard disks. It was designed by
- Western Digital and Compaq Computer in 1984. It was then named
- ST506. Quite a number of disks use the IDE interface.
-
- AT Attachment (ATA) is the superset of the IDE specifications.
- ST506 was also called ATA-1.
-
- Fast-IDE is ATA-2 (also named Fast ATA), Enhanced IDE (EIDE) is
- ATA-3. It provides support for larger disks (up to 8.4GB by means of
- the LBA standard), more disks (4 instead of 2) and for other mass
- storage units such as tapes and cdrom. UDMA/33 (aka UltraDMA/33) is
- ATA-4 and provides faster (and more CPU friendly) transfer modes
- than previous PIO (Programmed processor Input/Output) from previous
- ATA/IDE standards by means of fast DMA controllers.
-
- ATA Packet Interface (ATAPI) is a protocol used by EIDE tape and
- CD-ROM drives, similar in many respects to the SCSI protocol.
-
- SMART IDE (Self Monitoring, Analysis and Reporting Technology) was
- designed in order to prevent data corruption and disk crash by
- detecting pre hardware failure conditions (heat, access time, and
- the like...). Disks built since June 1995 may follow this standard.
- The kernel itself doesn't manage this; however there are quite a
- number of user programs such as smart that can query the status of
- SMART parameters from disk drives.
+ If you say Y here, your kernel will be able to manage ATA/(E)IDE and
+ ATAPI units. The most common cases are IDE hard drives and ATAPI
+ CD-ROM drives.
+
+ This subsystem is currently in maintenance mode with only bug fix
+ changes applied. Users of ATA hardware are encouraged to migrate to
+ the newer ATA subsystem ("Serial ATA (prod) and Parallel ATA
+ (experimental) drivers") which is more actively maintained.
To compile this driver as a module, choose M here: the
- module will be called ide.
+ module will be called ide-core.
For further information, please read <file:Documentation/ide/ide.txt>.
- If unsure, say Y.
+ If unsure, say N.
if IDE
comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
+config IDE_XFER_MODE
+ bool
+
config IDE_TIMINGS
bool
+ select IDE_XFER_MODE
config IDE_ATAPI
bool
+config IDE_LEGACY
+ bool
+
config BLK_DEV_IDE_SATA
bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
default n
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
+ select IDE_ATAPI
---help---
If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
To compile this driver as a module, choose M here: the
module will be called ide-tape.
-config BLK_DEV_IDESCSI
- tristate "SCSI emulation support (DEPRECATED)"
- depends on SCSI
- select IDE_ATAPI
- ---help---
- WARNING: ide-scsi is no longer needed for cd writing applications!
- The 2.6 kernel supports direct writing to ide-cd, which eliminates
- the need for ide-scsi + the entire scsi stack just for writing a
- cd. The new method is more efficient in every way.
-
- This will provide SCSI host adapter emulation for IDE ATAPI devices,
- and will allow you to use a SCSI device driver instead of a native
- ATAPI driver.
-
- If both this SCSI emulation and native ATAPI support are compiled
- into the kernel, the native support will be used.
-
config BLK_DEV_IDEACPI
bool "IDE ACPI support"
depends on ACPI
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- depends on ALPHA || X86 || IA64 || M32R || MIPS
+ depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC || ARCH_SHARK
+ default ARM && (ARCH_RPC || ARCH_SHARK)
help
This is the generic IDE driver. This driver attaches to the
fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and
# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
bool "Boot off-board chipsets first support (DEPRECATED)"
- depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
+ depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
help
Normally, IDE controllers built into the motherboard (on-board
controllers) are assigned to ide0 and ide1 while those on add-in PCI
It is safe to say Y to this question.
-config BLK_DEV_HPT34X
- tristate "HPT34X chipset support"
- depends on BROKEN
+config BLK_DEV_CS5536
+ tristate "CS5536 chipset support"
+ depends on X86_32
select BLK_DEV_IDEDMA_PCI
help
- This driver adds up to 4 more EIDE devices sharing a single
- interrupt. The HPT343 chipset in its current form is a non-bootable
- controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX)
- PCI UDMA controllers. This driver requires dynamic tuning of the
- chipset during the ide-probe at boot time. It is reported to support
- DVD II drives, by the manufacturer.
-
-config HPT34X_AUTODMA
- bool "HPT34X AUTODMA support (EXPERIMENTAL)"
- depends on BLK_DEV_HPT34X && EXPERIMENTAL
- help
- This is a dangerous thing to attempt currently! Please read the
- comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y
- here, then say Y to "Use DMA by default when available" as well.
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
If unsure, say N.
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
+config BLK_DEV_IT8172
+ tristate "IT8172 IDE support"
+ select BLK_DEV_IDEDMA_PCI
+ help
+ This driver adds support for the IDE controller on the
+ IT8172 System Controller.
+
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
select BLK_DEV_IDEDMA_PCI
endif
+# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
- depends on PPC_PMAC && IDE=y
+ depends on PPC_PMAC
select IDE_TIMINGS
+ select BLK_DEV_IDEDMA_PCI
help
This driver provides support for the on-board IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
CD-ROM on hda. This option changes this to more natural hda for
hard disk and hdc for CD-ROM.
-config BLK_DEV_IDEDMA_PMAC
- bool "PowerMac IDE DMA support"
- depends on BLK_DEV_IDE_PMAC
- select BLK_DEV_IDEDMA_PCI
- help
- This option allows the driver for the on-board IDE controller on
- Power Macintoshes and PowerBooks to use DMA (direct memory access)
- to transfer data to and from memory. Saying Y is safe and improves
- performance.
-
config BLK_DEV_IDE_AU1XXX
bool "IDE for AMD Alchemy Au1200"
depends on SOC_AU1200
+ select IDE_XFER_MODE
choice
prompt "IDE Mode for AMD Alchemy Au1200"
default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
endchoice
-config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
- int "Maximum transfer size (KB) per request (up to 128)"
- default "128"
- depends on BLK_DEV_IDE_AU1XXX
+config BLK_DEV_IDE_TX4938
+ tristate "TX4938 internal IDE support"
+ depends on SOC_TX4938
+ select IDE_TIMINGS
-config IDE_ARM
- tristate "ARM IDE support"
- depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
- default y
+config BLK_DEV_IDE_TX4939
+ tristate "TX4939 internal IDE support"
+ depends on SOC_TX4939
+ select BLK_DEV_IDEDMA_SFF
+
+config BLK_DEV_IDE_AT91
+ tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
+ depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
+ select IDE_TIMINGS
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
This includes on-board IDE interfaces on some Amiga models (A600,
A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
bus (M-Tech E-Matrix 530 expansion card).
- Say Y if you have an Amiga with a Gayle IDE interface and want to use
- IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
- it.
- Note that you also have to enable Zorro bus support if you want to
- use Gayle IDE interfaces on the Zorro expansion bus.
-config BLK_DEV_IDEDOUBLER
- bool "Amiga IDE Doubler support (EXPERIMENTAL)"
- depends on BLK_DEV_GAYLE && EXPERIMENTAL
- ---help---
- This feature provides support for the so-called `IDE doublers' (made
+ It also provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to
the on-board IDE interface of some Amiga models. Using such an IDE
doubler, you can connect up to four instead of two IDE devices to
- the Amiga's on-board IDE interface.
+ the Amiga's on-board IDE interface. The feature is enabled at kernel
+ runtime using the "gayle.doubler" kernel boot parameter.
- Note that the normal Amiga Gayle IDE driver may not work correctly
- if you have an IDE doubler and don't enable this feature!
+ Say Y if you have an Amiga with a Gayle IDE interface and want to use
+ IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
+ it.
- Say Y if you have an IDE doubler. The feature is enabled at kernel
- runtime using the "gayle.doubler" kernel boot parameter.
+ Note that you also have to enable Zorro bus support if you want to
+ use Gayle IDE interfaces on the Zorro expansion bus.
config BLK_DEV_BUDDHA
tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
+ select IDE_XFER_MODE
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
+ select IDE_XFER_MODE
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
+ def_bool BLK_DEV_IDEDMA_SFF || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+ select IDE_XFER_MODE
endif # IDE
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff