# Andre Hedrick <andre@linux-ide.org>
#
-if BLOCK
-
-menu "ATA/ATAPI/MFM/RLL support"
-
-config IDE
+menuconfig IDE
tristate "ATA/ATAPI/MFM/RLL support"
+ depends on BLOCK
+ depends on HAS_IOMEM
---help---
If you say Y here, your kernel will be able to manage low cost mass
storage units such as ATA/(E)IDE and ATAPI units. The most common
config IDE_MAX_HWIFS
int "Max IDE interfaces"
depends on ALPHA || SUPERH || IA64 || EMBEDDED
+ range 1 10
default 4
help
This is the maximum number of IDE hardware interfaces that will
---help---
There are two drivers for Serial ATA controllers.
- The main driver, "libata", exists inside the SCSI subsystem
- and supports most modern SATA controllers.
+ The main driver, "libata", uses the SCSI subsystem
+ and supports most modern SATA controllers. In order to use it
+ you may take a look at "Serial ATA (prod) and Parallel ATA
+ (experimental) drivers".
The IDE driver (which you are currently configuring) supports
a few first-generation SATA controllers.
If you are unsure, say N here.
+config IDE_PROC_FS
+ bool "legacy /proc/ide/ support"
+ depends on IDE && PROC_FS
+ default y
+ help
+ This option enables support for the various files in
+ /proc/ide. In Linux 2.6 this has been superseded by
+ files in sysfs but many legacy applications rely on this.
+
+ If unsure say Y.
+
comment "IDE chipset support/bugfixes"
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- default y
+ default H8300
help
- If unsure, say Y.
+ If unsure, say N.
config BLK_DEV_CMD640
bool "CMD640 chipset bugfix/support"
config BLK_DEV_IDEPNP
bool "PNP EIDE support"
depends on PNP
+ select IDE_GENERIC
help
If you have a PnP (Plug and Play) compatible EIDE card and
would like the kernel to automatically detect and activate
It is safe to say Y to this question, in most cases.
If unsure, say N.
+config IDEPCI_PCIBUS_ORDER
+ def_bool PCI && BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+
config BLK_DEV_OFFBOARD
bool "Boot off-board chipsets first support"
depends on PCI && BLK_DEV_IDEPCI
config BLK_DEV_GENERIC
tristate "Generic PCI IDE Chipset Support"
depends on BLK_DEV_IDEPCI
+ help
+ This option provides generic support for various PCI IDE Chipsets
+ which otherwise might not be supported.
config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
Generally say N here.
-config IDEDMA_PCI_AUTO
- bool "Use PCI DMA by default when available"
- ---help---
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
- It is normally safe to answer Y to this question unless your
- motherboard uses a VIA VP2 chipset, in which case you should say N.
-
config IDEDMA_ONLYDISK
bool "Enable DMA only for disks "
- depends on IDEDMA_PCI_AUTO
help
This is used if you know your ATAPI Devices are going to fail DMA
Transfers.
help
This driver adds support for Toshiba TC86C001 GOKU-S chip.
+config BLK_DEV_CELLEB
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PPC_CELLEB
+ help
+ This driver provides support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+ If unsure, say Y.
+
endif
config BLK_DEV_IDE_PMAC
depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
- def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ def_bool ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ select IDE_GENERIC
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
Say Y here if you want to add DMA (Direct Memory Access) support to
the ICS IDE driver.
-config IDEDMA_ICS_AUTO
- bool "Use ICS DMA by default"
- depends on BLK_DEV_IDEDMA_ICS
- help
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
config BLK_DEV_IDE_RAPIDE
tristate "RapIDE interface support"
depends on ARM && ARCH_ACORN
config BLK_DEV_GAYLE
bool "Amiga Gayle IDE interface support"
depends on AMIGA
+ select IDE_GENERIC
help
This is the IDE driver for the Amiga Gayle IDE interface. It supports
both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
config BLK_DEV_BUDDHA
bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
depends on ZORRO && EXPERIMENTAL
+ select IDE_GENERIC
help
This is the IDE driver for the IDE interfaces on the Buddha,
Catweasel and X-Surf expansion boards. It supports up to two interfaces
config BLK_DEV_FALCON_IDE
bool "Falcon IDE interface support"
depends on ATARI
+ select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on the Atari
Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
config BLK_DEV_MAC_IDE
bool "Macintosh Quadra/Powerbook IDE interface support"
depends on MAC
+ select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on some m68k
Macintosh models. It supports both the `Quadra style' (used in
config BLK_DEV_Q40IDE
bool "Q40/Q60 IDE interface support"
depends on Q40
+ select IDE_GENERIC
help
Enable the on-board IDE controller in the Q40/Q60. This should
normally be on; disable it only if you are running a custom hard
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
depends on 8xx && IDE=y && BLK_DEV_IDE=y
+ select IDE_GENERIC
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
help
- This driver is enabled at runtime using the "ide0=ali14xx" kernel
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
- This driver is enabled at runtime using the "ide0=dtc2278" kernel
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
well. See the <file:Documentation/ide.txt> and
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
help
- This driver is enabled at runtime using the "ide0=ht6560b" kernel
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
See the <file:Documentation/ide.txt> and
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
help
- This driver is enabled at runtime using the "ide0=qd65xx" kernel
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
<file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
more info.
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
help
- This driver is enabled at runtime using the "ide0=umc8672" kernel
+ This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
See the files <file:Documentation/ide.txt> and
It is normally safe to answer Y; however, the default is N.
-config IDEDMA_AUTO
- def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
endif
config BLK_DEV_HD_ONLY
config BLK_DEV_HD
def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY
-endif
-
-endmenu
-
-endif
+endif # IDE