SMART parameters from disk drives.
To compile this driver as a module, choose M here: the
- module will be called ide.
+ module will be called ide-core.ko.
For further information, please read <file:Documentation/ide/ide.txt>.
config IDE_ATAPI
bool
+config IDE_LEGACY
+ bool
+
config BLK_DEV_IDE_SATA
bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
default n
If unsure, say N.
-config BLK_DEV_IDEDISK
- tristate "Include IDE/ATA-2 DISK support"
- ---help---
- This will include enhanced support for MFM/RLL/IDE hard disks. If
- you have a MFM/RLL/IDE disk, and there is no special reason to use
- the old hard disk driver instead, say Y. If you have an SCSI-only
- system, you can say N here.
+config IDE_GD
+ tristate "generic ATA/ATAPI disk support"
+ default y
+ help
+ Support for ATA/ATAPI disks (including ATAPI floppy drives).
- To compile this driver as a module, choose M here: the
- module will be called ide-disk.
- Do not compile this driver as a module if your root file system
- (the one containing the directory /) is located on the IDE disk.
+ To compile this driver as a module, choose M here.
+ The module will be called ide-gd_mod.
If unsure, say Y.
+config IDE_GD_ATA
+ bool "ATA disk support"
+ depends on IDE_GD
+ default y
+ help
+ This will include support for ATA hard disks.
+
+ If unsure, say Y.
+
+config IDE_GD_ATAPI
+ bool "ATAPI floppy support"
+ depends on IDE_GD
+ select IDE_ATAPI
+ help
+ This will include support for ATAPI floppy drives
+ (i.e. Iomega ZIP or MKE LS-120).
+
+ For information about jumper settings and the question
+ of when a ZIP drive uses a partition table, see
+ <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
+
+ If unsure, say N.
+
config BLK_DEV_IDECS
tristate "PCMCIA IDE support"
depends on PCMCIA
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
+ select IDE_ATAPI
---help---
If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
To compile this driver as a module, choose M here: the
module will be called ide-tape.
-config BLK_DEV_IDEFLOPPY
- tristate "Include IDE/ATAPI FLOPPY support"
- select IDE_ATAPI
- ---help---
- If you have an IDE floppy drive which uses the ATAPI protocol,
- answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
- drives, similar to the SCSI protocol.
-
- The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by
- this driver. For information about jumper settings and the question
- of when a ZIP drive uses a partition table, see
- <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
- (ATAPI PD-CD/CDR drives are not supported by this driver; support
- for PD-CD/CDR drives is available if you answer Y to
- "SCSI emulation support", below).
-
- If you say Y here, the FLOPPY drive will be identified along with
- other IDE devices, as "hdb" or "hdc", or something similar (check
- the boot messages with dmesg).
-
- To compile this driver as a module, choose M here: the
- module will be called ide-floppy.
-
-config BLK_DEV_IDESCSI
- tristate "SCSI emulation support (DEPRECATED)"
- depends on SCSI
- select IDE_ATAPI
- ---help---
- WARNING: ide-scsi is no longer needed for cd writing applications!
- The 2.6 kernel supports direct writing to ide-cd, which eliminates
- the need for ide-scsi + the entire scsi stack just for writing a
- cd. The new method is more efficient in every way.
-
- This will provide SCSI host adapter emulation for IDE ATAPI devices,
- and will allow you to use a SCSI device driver instead of a native
- ATAPI driver.
-
- If both this SCSI emulation and native ATAPI support are compiled
- into the kernel, the native support will be used.
-
config BLK_DEV_IDEACPI
bool "IDE ACPI support"
depends on ACPI
# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
bool "Boot off-board chipsets first support (DEPRECATED)"
- depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
+ depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
help
Normally, IDE controllers built into the motherboard (on-board
controllers) are assigned to ide0 and ide1 while those on add-in PCI
It is safe to say Y to this question.
-config BLK_DEV_HPT34X
- tristate "HPT34X chipset support"
- depends on BROKEN
+config BLK_DEV_CS5536
+ tristate "CS5536 chipset support"
+ depends on X86_32
select BLK_DEV_IDEDMA_PCI
help
- This driver adds up to 4 more EIDE devices sharing a single
- interrupt. The HPT343 chipset in its current form is a non-bootable
- controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX)
- PCI UDMA controllers. This driver requires dynamic tuning of the
- chipset during the ide-probe at boot time. It is reported to support
- DVD II drives, by the manufacturer.
-
-config HPT34X_AUTODMA
- bool "HPT34X AUTODMA support (EXPERIMENTAL)"
- depends on BLK_DEV_HPT34X && EXPERIMENTAL
- help
- This is a dangerous thing to attempt currently! Please read the
- comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y
- here, then say Y to "Use DMA by default when available" as well.
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
If unsure, say N.
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
+config BLK_DEV_IT8172
+ tristate "IT8172 IDE support"
+ select BLK_DEV_IDEDMA_PCI
+ help
+ This driver adds support for the IDE controller on the
+ IT8172 System Controller.
+
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
select BLK_DEV_IDEDMA_PCI
endif
+# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
depends on PPC_PMAC && IDE=y
select IDE_TIMINGS
+ select BLK_DEV_IDEDMA_PCI
help
This driver provides support for the on-board IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
CD-ROM on hda. This option changes this to more natural hda for
hard disk and hdc for CD-ROM.
-config BLK_DEV_IDEDMA_PMAC
- bool "PowerMac IDE DMA support"
- depends on BLK_DEV_IDE_PMAC
- select BLK_DEV_IDEDMA_PCI
- help
- This option allows the driver for the on-board IDE controller on
- Power Macintoshes and PowerBooks to use DMA (direct memory access)
- to transfer data to and from memory. Saying Y is safe and improves
- performance.
-
config BLK_DEV_IDE_AU1XXX
bool "IDE for AMD Alchemy Au1200"
depends on SOC_AU1200
depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
endchoice
-config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
- int "Maximum transfer size (KB) per request (up to 128)"
- default "128"
- depends on BLK_DEV_IDE_AU1XXX
+config BLK_DEV_IDE_TX4938
+ tristate "TX4938 internal IDE support"
+ depends on SOC_TX4938
+ select IDE_TIMINGS
+
+config BLK_DEV_IDE_TX4939
+ tristate "TX4939 internal IDE support"
+ depends on SOC_TX4939
+ select BLK_DEV_IDEDMA_SFF
+
+config BLK_DEV_IDE_AT91
+ tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
+ depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
+ select IDE_TIMINGS
config IDE_ARM
tristate "ARM IDE support"
- depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ depends on ARM && (ARCH_RPC || ARCH_SHARK)
default y
config BLK_DEV_IDE_ICSIDE
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
select IDE_TIMINGS
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
+ select IDE_LEGACY
help
This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
endif
config BLK_DEV_IDEDMA
- def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
+ def_bool BLK_DEV_IDEDMA_SFF || \
BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
endif # IDE