#
# IDE ATA ATAPI Block device driver configuration
#
-# Andre Hedrick <andre@linux-ide.org>
-#
# Select HAVE_IDE if IDE is supported
config HAVE_IDE
comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"
+config IDE_TIMINGS
+ bool
+
+config IDE_ATAPI
+ bool
+
config BLK_DEV_IDE_SATA
bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
default n
config BLK_DEV_IDETAPE
tristate "Include IDE/ATAPI TAPE support"
+ select IDE_ATAPI
help
If you have an IDE tape drive using the ATAPI protocol, say Y.
ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
config BLK_DEV_IDEFLOPPY
tristate "Include IDE/ATAPI FLOPPY support"
+ select IDE_ATAPI
---help---
If you have an IDE floppy drive which uses the ATAPI protocol,
answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
config BLK_DEV_IDESCSI
tristate "SCSI emulation support"
depends on SCSI
+ select IDE_ATAPI
---help---
WARNING: ide-scsi is no longer needed for cd writing applications!
The 2.6 kernel supports direct writing to ide-cd, which eliminates
config BLK_DEV_CMD640
tristate "CMD640 chipset bugfix/support"
depends on X86
+ select IDE_TIMINGS
---help---
The CMD-Technologies CMD640 IDE chip is used on many common 486 and
Pentium motherboards, usually in combination with a "Neptune" or
This driver will work automatically in PCI based systems (most new
systems have PCI slots). But if your system uses VESA local bus
(VLB) instead of PCI, you must also supply a kernel boot parameter
- to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man
+ to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
bootparam" or see the documentation of your boot loader about how to
pass options to the kernel.)
config BLK_DEV_ALI15X3
tristate "ALI M15x3 chipset support"
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C
onboard chipsets. It also tests for Simplex mode and enables
normal dual channel support.
- If you say Y here, you also need to say Y to "Use DMA by default
- when available", above. Please read the comments at the top of
+ Please read the comments at the top of
<file:drivers/ide/pci/alim15x3.c>.
If unsure, say N.
-config WDC_ALI15X3
- bool "ALI M15x3 WDC support (DANGEROUS)"
- depends on BLK_DEV_ALI15X3
- ---help---
- This allows for UltraDMA support for WDC drives that ignore CRC
- checking. You are a fool for enabling this option, but there have
- been requests. DO NOT COMPLAIN IF YOUR DRIVE HAS FS CORRUPTION, IF
- YOU ENABLE THIS! No one will listen, just laugh for ignoring this
- SERIOUS WARNING.
-
- Using this option can allow WDC drives to run at ATA-4/5 transfer
- rates with only an ATA-2 support structure.
-
- SAY N!
-
config BLK_DEV_AMD74XX
tristate "AMD and nVidia IDE support"
depends on !ARM
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for AMD-7xx and AMD-8111 chips
config BLK_DEV_CMD64X
tristate "CMD64{3|6|8|9} chipset support"
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
Say Y here if you have an IDE controller which uses any of these
config BLK_DEV_CY82C693
tristate "CY82C693 chipset support"
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
This driver adds detection and support for the CY82C693 chipset
used on Digital's PC-Alpha 164SX boards.
- If you say Y here, you need to say Y to "Use DMA by default
- when available" as well.
-
config BLK_DEV_CS5520
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
National SCx200 series of embedded x86 "Geode" systems.
config BLK_DEV_PIIX
- tristate "Intel PIIXn chipsets support"
+ tristate "Intel PIIX/ICH chipsets support"
select BLK_DEV_IDEDMA_PCI
help
- This driver adds explicit support for Intel PIIX and ICH chips
- and also for the Efar Victory66 (slc90e66) chip. This allows
- the kernel to change PIO, DMA and UDMA speeds and to configure
- the chip to optimum performance.
+ This driver adds explicit support for Intel PIIX and ICH chips.
+ This allows the kernel to change PIO, DMA and UDMA speeds and to
+ configure the chip to optimum performance.
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
happen if the BIOS revisions of all installed cards (three-max) do
not match, the driver attempts to do dynamic tuning of the chipset
at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
- for more than one card. This card may require that you say Y to
- "Special UDMA Feature".
-
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
+ for more than one card.
Please read the comments at the top of
<file:drivers/ide/pci/pdc202xx_old.c>.
ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
SiS745, SiS750
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
config BLK_DEV_SL82C105
tristate "Winbond SL82c105 support"
depends on (PPC || ARM)
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
If you have a Winbond SL82c105 IDE controller, say Y here to enable
and it will handle timing cycles. Since this is an improved
look-a-like to the PIIX4 it should be a nice addition.
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
Please read the comments at the top of
<file:drivers/ide/pci/slc90e66.c>.
config BLK_DEV_VIA82CXXX
tristate "VIA82CXXX chipset support"
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for VIA BusMastering IDE chips.
config BLK_DEV_IDE_PMAC
tristate "PowerMac on-board IDE support"
depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
+ select IDE_TIMINGS
help
This driver provides support for the on-board IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
Say Y here if you want to support the Yellowstone RapIDE controller
manufactured for use with Acorn computers.
-config BLK_DEV_IDE_BAST
- tristate "Simtec BAST / Thorcom VR1000 IDE support"
- depends on ARM && (ARCH_BAST || MACH_VR1000)
- help
- Say Y here if you want to support the onboard IDE channels on the
- Simtec BAST or the Thorcom VR1000
-
-config ETRAX_IDE
- tristate "ETRAX IDE support"
- depends on CRIS && BROKEN
- select BLK_DEV_IDEDMA
- help
- Enables the ETRAX IDE driver.
-
- You can't use parallel ports or SCSI ports at the same time.
-
-config ETRAX_IDE_DELAY
- int "Delay for drives to regain consciousness"
- depends on ETRAX_IDE && ETRAX_ARCH_V10
- default 15
- help
- Number of seconds to wait for IDE drives to spin up after an IDE
- reset.
-
-choice
- prompt "IDE reset pin"
- depends on ETRAX_IDE && ETRAX_ARCH_V10
- default ETRAX_IDE_PB7_RESET
-
-config ETRAX_IDE_PB7_RESET
- bool "Port_PB_Bit_7"
- help
- IDE reset on pin 7 on port B
-
-config ETRAX_IDE_G27_RESET
- bool "Port_G_Bit_27"
- help
- IDE reset on pin 27 on port G
-
-endchoice
-
config IDE_H8300
tristate "H8300 IDE support"
depends on H8300
bool "Amiga IDE Doubler support (EXPERIMENTAL)"
depends on BLK_DEV_GAYLE && EXPERIMENTAL
---help---
- This driver provides support for the so-called `IDE doublers' (made
+ This feature provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to
the on-board IDE interface of some Amiga models. Using such an IDE
doubler, you can connect up to four instead of two IDE devices to
the Amiga's on-board IDE interface.
Note that the normal Amiga Gayle IDE driver may not work correctly
- if you have an IDE doubler and don't enable this driver!
+ if you have an IDE doubler and don't enable this feature!
- Say Y if you have an IDE doubler. The driver is enabled at kernel
- runtime using the "ide=doubler" kernel boot parameter.
+ Say Y if you have an IDE doubler. The feature is enabled at kernel
+ runtime using the "gayle.doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
config BLK_DEV_PALMCHIP_BK3710
tristate "Palmchip bk3710 IDE controller support"
depends on ARCH_DAVINCI
+ select IDE_TIMINGS
select BLK_DEV_IDEDMA_SFF
help
Say Y here if you want to support the onchip IDE controller on the
TI DaVinci SoC
-
-config BLK_DEV_MPC8xx_IDE
- tristate "MPC8xx IDE support"
- depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
- help
- This option provides support for IDE on Motorola MPC8xx Systems.
- Please see 'Type of MPC8xx IDE interface' for details.
-
- If unsure, say N.
-
-choice
- prompt "Type of MPC8xx IDE interface"
- depends on BLK_DEV_MPC8xx_IDE
- default IDE_8xx_PCCARD
-
-config IDE_8xx_PCCARD
- bool "8xx_PCCARD"
- ---help---
- Select how the IDE devices are connected to the MPC8xx system:
-
- 8xx_PCCARD uses the 8xx internal PCMCIA interface in combination
- with a PC Card (e.g. ARGOSY portable Hard Disk Adapter),
- ATA PC Card HDDs or ATA PC Flash Cards (example: TQM8xxL
- systems)
-
- 8xx_DIRECT is used for directly connected IDE devices using the 8xx
- internal PCMCIA interface (example: IVMS8 systems)
-
- EXT_DIRECT is used for IDE devices directly connected to the 8xx
- bus using some glue logic, but _not_ the 8xx internal
- PCMCIA interface (example: IDIF860 systems)
-
-config IDE_8xx_DIRECT
- bool "8xx_DIRECT"
-
-config IDE_EXT_DIRECT
- bool "EXT_DIRECT"
-
-endchoice
-
# no isa -> no vlb
if ISA && (ALPHA || X86 || MIPS)
comment "Note: most of these also require special kernel boot parameters"
config BLK_DEV_4DRIVES
- bool "Generic 4 drives/port support"
+ tristate "Generic 4 drives/port support"
help
Certain older chipsets, including the Tekram 690CD, use a single set
of I/O ports at 0x1f0 to control up to four drives, instead of the
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
+ select IDE_TIMINGS
help
This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
+ select IDE_TIMINGS
help
This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
+ select IDE_TIMINGS
help
This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
endif
-config BLK_DEV_HD_ONLY
- bool "Old hard disk (MFM/RLL/IDE) driver"
- help
- There are two drivers for MFM/RLL/IDE hard disks. Most people use
- the newer enhanced driver, but this old one is still around for two
- reasons. Some older systems have strange timing problems and seem to
- work only with the old driver (which itself does not work with some
- newer systems). The other reason is that the old driver is smaller,
- since it lacks the enhanced functionality of the new one. This makes
- it a good choice for systems with very tight memory restrictions, or
- for systems with only older MFM/RLL/ESDI drives. Choosing the old
- driver can save 13 KB or so of kernel memory.
-
- If you want to use this driver together with the new one you have
- to use "hda=noprobe hdb=noprobe" kernel parameters to prevent the new
- driver from probing the primary interface.
-
- If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
- instead of this one. For more detailed information, read the
- Disk-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
-config BLK_DEV_HD
- def_bool BLK_DEV_HD_ONLY
-
endif # IDE
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff