menu "Miscellaneous I2C Chip support"
-config DS1682
- tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
- depends on EXPERIMENTAL
- help
- If you say yes here you get support for Dallas Semiconductor
- DS1682 Total Elapsed Time Recorder.
-
- This driver can also be built as a module. If so, the module
- will be called ds1682.
-
-config AT24
- tristate "EEPROMs from most vendors"
- depends on SYSFS && EXPERIMENTAL
- help
- Enable this driver to get read/write support to most I2C EEPROMs,
- after you configure the driver to know about each EEPROM on
- your target board. Use these generic chip names, instead of
- vendor-specific ones like at24c64 or 24lc02:
-
- 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
- 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
-
- Unless you like data loss puzzles, always be sure that any chip
- you configure as a 24c32 (32 kbit) or larger is NOT really a
- 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
- as read-only won't help recover from this. Also, if your chip
- has any software write-protect mechanism you may want to review the
- code to make sure this driver won't turn it on by accident.
-
- If you use this with an SMBus adapter instead of an I2C adapter,
- full functionality is not available. Only smaller devices are
- supported (24c16 and below, max 4 kByte).
-
- This driver can also be built as a module. If so, the module
- will be called at24.
-
-config SENSORS_EEPROM
- tristate "EEPROM reader"
- depends on EXPERIMENTAL
- help
- If you say yes here you get read-only access to the EEPROM data
- available on modern memory DIMMs and Sony Vaio laptops. Such
- EEPROMs could theoretically be available on other devices as well.
-
- This driver can also be built as a module. If so, the module
- will be called eeprom.
-
-config SENSORS_PCF8574
- tristate "Philips PCF8574 and PCF8574A (DEPRECATED)"
- depends on EXPERIMENTAL && GPIO_PCF857X = "n"
- default n
- help
- If you say yes here you get support for Philips PCF8574 and
- PCF8574A chips. These chips are 8-bit I/O expanders for the I2C bus.
-
- This driver can also be built as a module. If so, the module
- will be called pcf8574.
-
- This driver is deprecated and will be dropped soon. Use
- drivers/gpio/pcf857x.c instead.
-
- These devices are hard to detect and rarely found on mainstream
- hardware. If unsure, say N.
-
-config PCF8575
- tristate "Philips PCF8575 (DEPRECATED)"
- default n
- depends on GPIO_PCF857X = "n"
- help
- If you say yes here you get support for Philips PCF8575 chip.
- This chip is a 16-bit I/O expander for the I2C bus. Several other
- chip manufacturers sell equivalent chips, e.g. Texas Instruments.
-
- This driver can also be built as a module. If so, the module
- will be called pcf8575.
-
- This driver is deprecated and will be dropped soon. Use
- drivers/gpio/pcf857x.c instead.
-
- This device is hard to detect and is rarely found on mainstream
- hardware. If unsure, say N.
-
-config SENSORS_PCA9539
- tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
- depends on EXPERIMENTAL && GPIO_PCA953X = "n"
- help
- If you say yes here you get support for the Philips PCA9539
- 16-bit I/O port.
-
- This driver can also be built as a module. If so, the module
- will be called pca9539.
-
- This driver is deprecated and will be dropped soon. Use
- drivers/gpio/pca953x.c instead.
-
-config SENSORS_PCF8591
- tristate "Philips PCF8591"
- depends on EXPERIMENTAL
- default n
- help
- If you say yes here you get support for Philips PCF8591 chips.
-
- This driver can also be built as a module. If so, the module
- will be called pcf8591.
-
- These devices are hard to detect and rarely found on mainstream
- hardware. If unsure, say N.
-
-config SENSORS_MAX6875
- tristate "Maxim MAX6875 Power supply supervisor"
- depends on EXPERIMENTAL
- help
- If you say yes here you get support for the Maxim MAX6875
- EEPROM-programmable, quad power-supply sequencer/supervisor.
-
- This provides an interface to program the EEPROM and reset the chip.
-
- This driver also supports the Maxim MAX6874 hex power-supply
- sequencer/supervisor if found at a compatible address.
-
- This driver can also be built as a module. If so, the module
- will be called max6875.
-
config SENSORS_TSL2550
tristate "Taos TSL2550 ambient light sensor"
depends on EXPERIMENTAL
This driver can also be built as a module. If so, the module
will be called tsl2550.
-config MCU_MPC8349EMITX
- tristate "MPC8349E-mITX MCU driver"
- depends on I2C && PPC_83xx
- select GENERIC_GPIO
- select ARCH_REQUIRE_GPIOLIB
- help
- Say Y here to enable soft power-off functionality on the Freescale
- boards with the MPC8349E-mITX-compatible MCU chips. This driver will
- also register MCU GPIOs with the generic GPIO API, so you'll able
- to use MCU pins as GPIOs.
-
endmenu