Supports following chips:
Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
- w83791d 10 5 3 3 0x71 0x5ca3 yes no
+ w83791d 10 5 5 3 0x71 0x5ca3 yes no
The w83791d chip appears to be part way between the 83781d and the
83792d. Thus, this file is derived from both the w83792d.c and
#define NUMBER_OF_VIN 10
#define NUMBER_OF_FANIN 5
#define NUMBER_OF_TEMPIN 3
+#define NUMBER_OF_PWM 5
/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(w83791d);
-I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
+
+static unsigned short force_subclients[4];
+module_param_array(force_subclients, short, NULL, 0);
+MODULE_PARM_DESC(force_subclients, "List of subclient addresses: "
"{bus, clientaddr, subclientaddr1, subclientaddr2}");
static int reset;
0xBD, /* FAN 5 Count Low Limit in DataSheet */
};
+static const u8 W83791D_REG_PWM[NUMBER_OF_PWM] = {
+ 0x81, /* PWM 1 duty cycle register in DataSheet */
+ 0x83, /* PWM 2 duty cycle register in DataSheet */
+ 0x94, /* PWM 3 duty cycle register in DataSheet */
+ 0xA0, /* PWM 4 duty cycle register in DataSheet */
+ 0xA1, /* PWM 5 duty cycle register in DataSheet */
+};
+
+static const u8 W83791D_REG_TEMP_TARGET[3] = {
+ 0x85, /* PWM 1 target temperature for temp 1 */
+ 0x86, /* PWM 2 target temperature for temp 2 */
+ 0x96, /* PWM 3 target temperature for temp 3 */
+};
+
+static const u8 W83791D_REG_TEMP_TOL[2] = {
+ 0x87, /* PWM 1/2 temperature tolerance */
+ 0x97, /* PWM 3 temperature tolerance */
+};
+
static const u8 W83791D_REG_FAN_CFG[2] = {
0x84, /* FAN 1/2 configuration */
0x95, /* FAN 3 configuration */
0xA3, /* BEEP Control Register 3 */
};
+#define W83791D_REG_GPIO 0x15
#define W83791D_REG_CONFIG 0x40
#define W83791D_REG_VID_FANDIV 0x47
#define W83791D_REG_DID_VID4 0x49
(val) < 0 ? ((val) - 250) / 500 * 128 : \
((val) + 250) / 500 * 128)
+/* for thermal cruise target temp, 7-bits, LSB = 1 degree Celsius */
+#define TARGET_TEMP_TO_REG(val) ((val) < 0 ? 0 : \
+ (val) >= 127000 ? 127 : \
+ ((val) + 500) / 1000)
+
+/* for thermal cruise temp tolerance, 4-bits, LSB = 1 degree Celsius */
+#define TOL_TEMP_TO_REG(val) ((val) < 0 ? 0 : \
+ (val) >= 15000 ? 15 : \
+ ((val) + 500) / 1000)
#define BEEP_MASK_TO_REG(val) ((val) & 0xffffff)
#define BEEP_MASK_FROM_REG(val) ((val) & 0xffffff)
two sensors with three values
(cur, over, hyst) */
+ /* PWMs */
+ u8 pwm[5]; /* pwm duty cycle */
+ u8 pwm_enable[3]; /* pwm enable status for fan 1-3
+ (fan 4-5 only support manual mode) */
+
+ u8 temp_target[3]; /* pwm 1-3 target temperature */
+ u8 temp_tolerance[3]; /* pwm 1-3 temperature tolerance */
+
/* Misc */
u32 alarms; /* realtime status register encoding,combined */
u8 beep_enable; /* Global beep enable */
SENSOR_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 22),
};
+/* read/write PWMs */
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ int nr = sensor_attr->index;
+ struct w83791d_data *data = w83791d_update_device(dev);
+ return sprintf(buf, "%u\n", data->pwm[nr]);
+}
+
+static ssize_t store_pwm(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83791d_data *data = i2c_get_clientdata(client);
+ int nr = sensor_attr->index;
+ unsigned long val;
+
+ if (strict_strtoul(buf, 10, &val))
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ data->pwm[nr] = SENSORS_LIMIT(val, 0, 255);
+ w83791d_write(client, W83791D_REG_PWM[nr], data->pwm[nr]);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static struct sensor_device_attribute sda_pwm[] = {
+ SENSOR_ATTR(pwm1, S_IWUSR | S_IRUGO,
+ show_pwm, store_pwm, 0),
+ SENSOR_ATTR(pwm2, S_IWUSR | S_IRUGO,
+ show_pwm, store_pwm, 1),
+ SENSOR_ATTR(pwm3, S_IWUSR | S_IRUGO,
+ show_pwm, store_pwm, 2),
+ SENSOR_ATTR(pwm4, S_IWUSR | S_IRUGO,
+ show_pwm, store_pwm, 3),
+ SENSOR_ATTR(pwm5, S_IWUSR | S_IRUGO,
+ show_pwm, store_pwm, 4),
+};
+
+static ssize_t show_pwmenable(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ int nr = sensor_attr->index;
+ struct w83791d_data *data = w83791d_update_device(dev);
+ return sprintf(buf, "%u\n", data->pwm_enable[nr] + 1);
+}
+
+static ssize_t store_pwmenable(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83791d_data *data = i2c_get_clientdata(client);
+ int nr = sensor_attr->index;
+ unsigned long val;
+ u8 reg_cfg_tmp;
+ u8 reg_idx = 0;
+ u8 val_shift = 0;
+ u8 keep_mask = 0;
+
+ int ret = strict_strtoul(buf, 10, &val);
+
+ if (ret || val < 1 || val > 3)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ data->pwm_enable[nr] = val - 1;
+ switch (nr) {
+ case 0:
+ reg_idx = 0;
+ val_shift = 2;
+ keep_mask = 0xf3;
+ break;
+ case 1:
+ reg_idx = 0;
+ val_shift = 4;
+ keep_mask = 0xcf;
+ break;
+ case 2:
+ reg_idx = 1;
+ val_shift = 2;
+ keep_mask = 0xf3;
+ break;
+ }
+
+ reg_cfg_tmp = w83791d_read(client, W83791D_REG_FAN_CFG[reg_idx]);
+ reg_cfg_tmp = (reg_cfg_tmp & keep_mask) |
+ data->pwm_enable[nr] << val_shift;
+
+ w83791d_write(client, W83791D_REG_FAN_CFG[reg_idx], reg_cfg_tmp);
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+static struct sensor_device_attribute sda_pwmenable[] = {
+ SENSOR_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
+ show_pwmenable, store_pwmenable, 0),
+ SENSOR_ATTR(pwm2_enable, S_IWUSR | S_IRUGO,
+ show_pwmenable, store_pwmenable, 1),
+ SENSOR_ATTR(pwm3_enable, S_IWUSR | S_IRUGO,
+ show_pwmenable, store_pwmenable, 2),
+};
+
+/* For Smart Fan I / Thermal Cruise */
+static ssize_t show_temp_target(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct w83791d_data *data = w83791d_update_device(dev);
+ int nr = sensor_attr->index;
+ return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp_target[nr]));
+}
+
+static ssize_t store_temp_target(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83791d_data *data = i2c_get_clientdata(client);
+ int nr = sensor_attr->index;
+ unsigned long val;
+ u8 target_mask;
+
+ if (strict_strtoul(buf, 10, &val))
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ data->temp_target[nr] = TARGET_TEMP_TO_REG(val);
+ target_mask = w83791d_read(client,
+ W83791D_REG_TEMP_TARGET[nr]) & 0x80;
+ w83791d_write(client, W83791D_REG_TEMP_TARGET[nr],
+ data->temp_target[nr] | target_mask);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static struct sensor_device_attribute sda_temp_target[] = {
+ SENSOR_ATTR(temp1_target, S_IWUSR | S_IRUGO,
+ show_temp_target, store_temp_target, 0),
+ SENSOR_ATTR(temp2_target, S_IWUSR | S_IRUGO,
+ show_temp_target, store_temp_target, 1),
+ SENSOR_ATTR(temp3_target, S_IWUSR | S_IRUGO,
+ show_temp_target, store_temp_target, 2),
+};
+
+static ssize_t show_temp_tolerance(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct w83791d_data *data = w83791d_update_device(dev);
+ int nr = sensor_attr->index;
+ return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp_tolerance[nr]));
+}
+
+static ssize_t store_temp_tolerance(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83791d_data *data = i2c_get_clientdata(client);
+ int nr = sensor_attr->index;
+ unsigned long val;
+ u8 target_mask;
+ u8 reg_idx = 0;
+ u8 val_shift = 0;
+ u8 keep_mask = 0;
+
+ if (strict_strtoul(buf, 10, &val))
+ return -EINVAL;
+
+ switch (nr) {
+ case 0:
+ reg_idx = 0;
+ val_shift = 0;
+ keep_mask = 0xf0;
+ break;
+ case 1:
+ reg_idx = 0;
+ val_shift = 4;
+ keep_mask = 0x0f;
+ break;
+ case 2:
+ reg_idx = 1;
+ val_shift = 0;
+ keep_mask = 0xf0;
+ break;
+ }
+
+ mutex_lock(&data->update_lock);
+ data->temp_tolerance[nr] = TOL_TEMP_TO_REG(val);
+ target_mask = w83791d_read(client,
+ W83791D_REG_TEMP_TOL[reg_idx]) & keep_mask;
+ w83791d_write(client, W83791D_REG_TEMP_TOL[reg_idx],
+ (data->temp_tolerance[nr] << val_shift) | target_mask);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static struct sensor_device_attribute sda_temp_tolerance[] = {
+ SENSOR_ATTR(temp1_tolerance, S_IWUSR | S_IRUGO,
+ show_temp_tolerance, store_temp_tolerance, 0),
+ SENSOR_ATTR(temp2_tolerance, S_IWUSR | S_IRUGO,
+ show_temp_tolerance, store_temp_tolerance, 1),
+ SENSOR_ATTR(temp3_tolerance, S_IWUSR | S_IRUGO,
+ show_temp_tolerance, store_temp_tolerance, 2),
+};
+
/* read/write the temperature1, includes measured value and limits */
static ssize_t show_temp1(struct device *dev, struct device_attribute *devattr,
char *buf)
FAN_UNIT_ATTRS(0),
FAN_UNIT_ATTRS(1),
FAN_UNIT_ATTRS(2),
- FAN_UNIT_ATTRS(3),
- FAN_UNIT_ATTRS(4),
TEMP_UNIT_ATTRS(0),
TEMP_UNIT_ATTRS(1),
TEMP_UNIT_ATTRS(2),
&sda_beep_ctrl[1].dev_attr.attr,
&dev_attr_cpu0_vid.attr,
&dev_attr_vrm.attr,
+ &sda_pwm[0].dev_attr.attr,
+ &sda_pwm[1].dev_attr.attr,
+ &sda_pwm[2].dev_attr.attr,
+ &sda_pwmenable[0].dev_attr.attr,
+ &sda_pwmenable[1].dev_attr.attr,
+ &sda_pwmenable[2].dev_attr.attr,
+ &sda_temp_target[0].dev_attr.attr,
+ &sda_temp_target[1].dev_attr.attr,
+ &sda_temp_target[2].dev_attr.attr,
+ &sda_temp_tolerance[0].dev_attr.attr,
+ &sda_temp_tolerance[1].dev_attr.attr,
+ &sda_temp_tolerance[2].dev_attr.attr,
NULL
};
.attrs = w83791d_attributes,
};
+/* Separate group of attributes for fan/pwm 4-5. Their pins can also be
+ in use for GPIO in which case their sysfs-interface should not be made
+ available */
+static struct attribute *w83791d_attributes_fanpwm45[] = {
+ FAN_UNIT_ATTRS(3),
+ FAN_UNIT_ATTRS(4),
+ &sda_pwm[3].dev_attr.attr,
+ &sda_pwm[4].dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group w83791d_group_fanpwm45 = {
+ .attrs = w83791d_attributes_fanpwm45,
+};
static int w83791d_detect_subclients(struct i2c_client *client)
{
{
struct w83791d_data *data;
struct device *dev = &client->dev;
- int i, val1, err;
+ int i, err;
+ u8 has_fanpwm45;
#ifdef DEBUG
+ int val1;
val1 = w83791d_read(client, W83791D_REG_DID_VID4);
dev_dbg(dev, "Device ID version: %d.%d (0x%02x)\n",
(val1 >> 5) & 0x07, (val1 >> 1) & 0x0f, val1);
if ((err = sysfs_create_group(&client->dev.kobj, &w83791d_group)))
goto error3;
+ /* Check if pins of fan/pwm 4-5 are in use as GPIO */
+ has_fanpwm45 = w83791d_read(client, W83791D_REG_GPIO) & 0x10;
+ if (has_fanpwm45) {
+ err = sysfs_create_group(&client->dev.kobj,
+ &w83791d_group_fanpwm45);
+ if (err)
+ goto error4;
+ }
+
/* Everything is ready, now register the working device */
data->hwmon_dev = hwmon_device_register(dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
- goto error4;
+ goto error5;
}
return 0;
+error5:
+ if (has_fanpwm45)
+ sysfs_remove_group(&client->dev.kobj, &w83791d_group_fanpwm45);
error4:
sysfs_remove_group(&client->dev.kobj, &w83791d_group);
error3:
for (i = 0; i < 3; i++)
data->fan_div[i] |= (vbat_reg >> (3 + i)) & 0x04;
+ /* Update PWM duty cycle */
+ for (i = 0; i < NUMBER_OF_PWM; i++) {
+ data->pwm[i] = w83791d_read(client,
+ W83791D_REG_PWM[i]);
+ }
+
+ /* Update PWM enable status */
+ for (i = 0; i < 2; i++) {
+ reg_array_tmp[i] = w83791d_read(client,
+ W83791D_REG_FAN_CFG[i]);
+ }
+ data->pwm_enable[0] = (reg_array_tmp[0] >> 2) & 0x03;
+ data->pwm_enable[1] = (reg_array_tmp[0] >> 4) & 0x03;
+ data->pwm_enable[2] = (reg_array_tmp[1] >> 2) & 0x03;
+
+ /* Update PWM target temperature */
+ for (i = 0; i < 3; i++) {
+ data->temp_target[i] = w83791d_read(client,
+ W83791D_REG_TEMP_TARGET[i]) & 0x7f;
+ }
+
+ /* Update PWM temperature tolerance */
+ for (i = 0; i < 2; i++) {
+ reg_array_tmp[i] = w83791d_read(client,
+ W83791D_REG_TEMP_TOL[i]);
+ }
+ data->temp_tolerance[0] = reg_array_tmp[0] & 0x0f;
+ data->temp_tolerance[1] = (reg_array_tmp[0] >> 4) & 0x0f;
+ data->temp_tolerance[2] = reg_array_tmp[1] & 0x0f;
+
/* Update the first temperature sensor */
for (i = 0; i < 3; i++) {
data->temp1[i] = w83791d_read(client,
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff