* Philip Edelbrock <phil@netroedge.com>
* Stephen Rousset <stephen.rousset@rocketlogix.com>
* Dan Eaton <dan.eaton@rocketlogix.com>
- * Copyright (C) 2004 Jean Delvare <khali@linux-fr.org>
+ * Copyright (C) 2004-2008 Jean Delvare <khali@linux-fr.org>
*
* Original port to Linux 2.6 by Jeff Oliver.
*
* http://www.national.com/pf/LM/LM87.html
*
* Some functions share pins, so not all functions are available at the same
- * time. Which are depends on the hardware setup. This driver assumes that
- * the BIOS configured the chip correctly. In that respect, it differs from
- * the original driver (from lm_sensors for Linux 2.4), which would force the
- * LM87 to an arbitrary, compile-time chosen mode, regardless of the actual
- * chipset wiring.
+ * time. Which are depends on the hardware setup. This driver normally
+ * assumes that firmware configured the chip correctly. Where this is not
+ * the case, platform code must set the I2C client's platform_data to point
+ * to a u8 value to be written to the channel register.
* For reference, here is the list of exclusive functions:
* - in0+in5 (default) or temp3
* - fan1 (default) or in6
* instead. The LM87 is the only hardware monitoring chipset I know of
* which uses amplitude modulation. Be careful when using this feature.
*
+ * This driver also supports the ADM1024, a sensor chip made by Analog
+ * Devices. That chip is fully compatible with the LM87. Complete
+ * datasheet can be obtained from Analog's website at:
+ * http://www.analog.com/en/prod/0,2877,ADM1024,00.html
+ *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <linux/mutex.h>
* LM87 has three possible addresses: 0x2c, 0x2d and 0x2e.
*/
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
-
-/*
- * Insmod parameters
- */
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
-I2C_CLIENT_INSMOD_1(lm87);
+enum chips { lm87, adm1024 };
/*
* The LM87 registers
(((val) < 0 ? (val)-500 : (val)+500) / 1000))
#define FAN_FROM_REG(reg,div) ((reg) == 255 || (reg) == 0 ? 0 : \
- 1350000 + (reg)*(div) / 2) / ((reg)*(div))
+ (1350000 + (reg)*(div) / 2) / ((reg)*(div)))
#define FAN_TO_REG(val,div) ((val)*(div) * 255 <= 1350000 ? 255 : \
(1350000 + (val)*(div) / 2) / ((val)*(div)))
#define CHAN_NO_FAN(nr) (1 << (nr))
#define CHAN_TEMP3 (1 << 2)
#define CHAN_VCC_5V (1 << 3)
-#define CHAN_NO_VID (1 << 8)
+#define CHAN_NO_VID (1 << 7)
/*
* Functions declaration
*/
-static int lm87_attach_adapter(struct i2c_adapter *adapter);
-static int lm87_detect(struct i2c_adapter *adapter, int address, int kind);
+static int lm87_probe(struct i2c_client *client,
+ const struct i2c_device_id *id);
+static int lm87_detect(struct i2c_client *new_client,
+ struct i2c_board_info *info);
static void lm87_init_client(struct i2c_client *client);
-static int lm87_detach_client(struct i2c_client *client);
+static int lm87_remove(struct i2c_client *client);
static struct lm87_data *lm87_update_device(struct device *dev);
/*
* Driver data (common to all clients)
*/
+static const struct i2c_device_id lm87_id[] = {
+ { "lm87", lm87 },
+ { "adm1024", adm1024 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lm87_id);
+
static struct i2c_driver lm87_driver = {
+ .class = I2C_CLASS_HWMON,
.driver = {
.name = "lm87",
},
- .id = I2C_DRIVERID_LM87,
- .attach_adapter = lm87_attach_adapter,
- .detach_client = lm87_detach_client,
+ .probe = lm87_probe,
+ .remove = lm87_remove,
+ .id_table = lm87_id,
+ .detect = lm87_detect,
+ .address_list = normal_i2c,
};
/*
*/
struct lm87_data {
- struct i2c_client client;
- struct class_device *class_dev;
+ struct device *hwmon_dev;
struct mutex update_lock;
char valid; /* zero until following fields are valid */
unsigned long last_updated; /* In jiffies */
u8 channel; /* register value */
+ u8 config; /* original register value */
u8 in[8]; /* register value */
u8 in_max[8]; /* register value */
static ssize_t show_vrm(struct device *dev, struct device_attribute *attr, char *buf)
{
- struct lm87_data *data = lm87_update_device(dev);
+ struct lm87_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%d\n", data->vrm);
}
static ssize_t set_vrm(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
{
- struct i2c_client *client = to_i2c_client(dev);
- struct lm87_data *data = i2c_get_clientdata(client);
+ struct lm87_data *data = dev_get_drvdata(dev);
data->vrm = simple_strtoul(buf, NULL, 10);
return count;
}
}
static DEVICE_ATTR(aout_output, S_IRUGO | S_IWUSR, show_aout, set_aout);
-/*
- * Real code
- */
-
-static int lm87_attach_adapter(struct i2c_adapter *adapter)
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
{
- if (!(adapter->class & I2C_CLASS_HWMON))
- return 0;
- return i2c_probe(adapter, &addr_data, lm87_detect);
+ struct lm87_data *data = lm87_update_device(dev);
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
}
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8);
+static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 9);
+static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 7);
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 5);
+static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6);
+static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 14);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 15);
/*
- * The following function does more than just detection. If detection
- * succeeds, it also registers the new chip.
+ * Real code
*/
-static int lm87_detect(struct i2c_adapter *adapter, int address, int kind)
+
+static struct attribute *lm87_attributes[] = {
+ &dev_attr_in1_input.attr,
+ &dev_attr_in1_min.attr,
+ &dev_attr_in1_max.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
+ &dev_attr_in2_input.attr,
+ &dev_attr_in2_min.attr,
+ &dev_attr_in2_max.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
+ &dev_attr_in3_input.attr,
+ &dev_attr_in3_min.attr,
+ &dev_attr_in3_max.attr,
+ &sensor_dev_attr_in3_alarm.dev_attr.attr,
+ &dev_attr_in4_input.attr,
+ &dev_attr_in4_min.attr,
+ &dev_attr_in4_max.attr,
+ &sensor_dev_attr_in4_alarm.dev_attr.attr,
+
+ &dev_attr_temp1_input.attr,
+ &dev_attr_temp1_max.attr,
+ &dev_attr_temp1_min.attr,
+ &dev_attr_temp1_crit.attr,
+ &sensor_dev_attr_temp1_alarm.dev_attr.attr,
+ &dev_attr_temp2_input.attr,
+ &dev_attr_temp2_max.attr,
+ &dev_attr_temp2_min.attr,
+ &dev_attr_temp2_crit.attr,
+ &sensor_dev_attr_temp2_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_fault.dev_attr.attr,
+
+ &dev_attr_alarms.attr,
+ &dev_attr_aout_output.attr,
+
+ NULL
+};
+
+static const struct attribute_group lm87_group = {
+ .attrs = lm87_attributes,
+};
+
+static struct attribute *lm87_attributes_opt[] = {
+ &dev_attr_in6_input.attr,
+ &dev_attr_in6_min.attr,
+ &dev_attr_in6_max.attr,
+ &sensor_dev_attr_in6_alarm.dev_attr.attr,
+
+ &dev_attr_fan1_input.attr,
+ &dev_attr_fan1_min.attr,
+ &dev_attr_fan1_div.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
+
+ &dev_attr_in7_input.attr,
+ &dev_attr_in7_min.attr,
+ &dev_attr_in7_max.attr,
+ &sensor_dev_attr_in7_alarm.dev_attr.attr,
+
+ &dev_attr_fan2_input.attr,
+ &dev_attr_fan2_min.attr,
+ &dev_attr_fan2_div.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
+
+ &dev_attr_temp3_input.attr,
+ &dev_attr_temp3_max.attr,
+ &dev_attr_temp3_min.attr,
+ &dev_attr_temp3_crit.attr,
+ &sensor_dev_attr_temp3_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_fault.dev_attr.attr,
+
+ &dev_attr_in0_input.attr,
+ &dev_attr_in0_min.attr,
+ &dev_attr_in0_max.attr,
+ &sensor_dev_attr_in0_alarm.dev_attr.attr,
+ &dev_attr_in5_input.attr,
+ &dev_attr_in5_min.attr,
+ &dev_attr_in5_max.attr,
+ &sensor_dev_attr_in5_alarm.dev_attr.attr,
+
+ &dev_attr_cpu0_vid.attr,
+ &dev_attr_vrm.attr,
+
+ NULL
+};
+
+static const struct attribute_group lm87_group_opt = {
+ .attrs = lm87_attributes_opt,
+};
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int lm87_detect(struct i2c_client *new_client,
+ struct i2c_board_info *info)
{
- struct i2c_client *new_client;
- struct lm87_data *data;
- int err = 0;
+ struct i2c_adapter *adapter = new_client->adapter;
+ const char *name;
+ u8 cid, rev;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
- goto exit;
+ return -ENODEV;
- if (!(data = kzalloc(sizeof(struct lm87_data), GFP_KERNEL))) {
- err = -ENOMEM;
- goto exit;
+ if (lm87_read_value(new_client, LM87_REG_CONFIG) & 0x80)
+ return -ENODEV;
+
+ /* Now, we do the remaining detection. */
+ cid = lm87_read_value(new_client, LM87_REG_COMPANY_ID);
+ rev = lm87_read_value(new_client, LM87_REG_REVISION);
+
+ if (cid == 0x02 /* National Semiconductor */
+ && (rev >= 0x01 && rev <= 0x08))
+ name = "lm87";
+ else if (cid == 0x41 /* Analog Devices */
+ && (rev & 0xf0) == 0x10)
+ name = "adm1024";
+ else {
+ dev_dbg(&adapter->dev, "LM87 detection failed at 0x%02x\n",
+ new_client->addr);
+ return -ENODEV;
}
- /* The common I2C client data is placed right before the
- LM87-specific data. */
- new_client = &data->client;
- i2c_set_clientdata(new_client, data);
- new_client->addr = address;
- new_client->adapter = adapter;
- new_client->driver = &lm87_driver;
- new_client->flags = 0;
+ strlcpy(info->type, name, I2C_NAME_SIZE);
- /* Default to an LM87 if forced */
- if (kind == 0)
- kind = lm87;
+ return 0;
+}
- /* Now, we do the remaining detection. */
- if (kind < 0) {
- u8 rev = lm87_read_value(new_client, LM87_REG_REVISION);
-
- if (rev < 0x01 || rev > 0x08
- || (lm87_read_value(new_client, LM87_REG_CONFIG) & 0x80)
- || lm87_read_value(new_client, LM87_REG_COMPANY_ID) != 0x02) {
- dev_dbg(&adapter->dev,
- "LM87 detection failed at 0x%02x.\n",
- address);
- goto exit_free;
- }
+static int lm87_probe(struct i2c_client *new_client,
+ const struct i2c_device_id *id)
+{
+ struct lm87_data *data;
+ int err;
+
+ data = kzalloc(sizeof(struct lm87_data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
}
- /* We can fill in the remaining client fields */
- strlcpy(new_client->name, "lm87", I2C_NAME_SIZE);
+ i2c_set_clientdata(new_client, data);
data->valid = 0;
mutex_init(&data->update_lock);
- /* Tell the I2C layer a new client has arrived */
- if ((err = i2c_attach_client(new_client)))
- goto exit_free;
-
/* Initialize the LM87 chip */
lm87_init_client(new_client);
data->in_scale[7] = 1875;
/* Register sysfs hooks */
- data->class_dev = hwmon_device_register(&new_client->dev);
- if (IS_ERR(data->class_dev)) {
- err = PTR_ERR(data->class_dev);
- goto exit_detach;
- }
-
- device_create_file(&new_client->dev, &dev_attr_in1_input);
- device_create_file(&new_client->dev, &dev_attr_in1_min);
- device_create_file(&new_client->dev, &dev_attr_in1_max);
- device_create_file(&new_client->dev, &dev_attr_in2_input);
- device_create_file(&new_client->dev, &dev_attr_in2_min);
- device_create_file(&new_client->dev, &dev_attr_in2_max);
- device_create_file(&new_client->dev, &dev_attr_in3_input);
- device_create_file(&new_client->dev, &dev_attr_in3_min);
- device_create_file(&new_client->dev, &dev_attr_in3_max);
- device_create_file(&new_client->dev, &dev_attr_in4_input);
- device_create_file(&new_client->dev, &dev_attr_in4_min);
- device_create_file(&new_client->dev, &dev_attr_in4_max);
+ if ((err = sysfs_create_group(&new_client->dev.kobj, &lm87_group)))
+ goto exit_free;
if (data->channel & CHAN_NO_FAN(0)) {
- device_create_file(&new_client->dev, &dev_attr_in6_input);
- device_create_file(&new_client->dev, &dev_attr_in6_min);
- device_create_file(&new_client->dev, &dev_attr_in6_max);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_in6_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in6_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in6_max))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_in6_alarm.dev_attr)))
+ goto exit_remove;
} else {
- device_create_file(&new_client->dev, &dev_attr_fan1_input);
- device_create_file(&new_client->dev, &dev_attr_fan1_min);
- device_create_file(&new_client->dev, &dev_attr_fan1_div);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_fan1_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_fan1_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_fan1_div))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_fan1_alarm.dev_attr)))
+ goto exit_remove;
}
+
if (data->channel & CHAN_NO_FAN(1)) {
- device_create_file(&new_client->dev, &dev_attr_in7_input);
- device_create_file(&new_client->dev, &dev_attr_in7_min);
- device_create_file(&new_client->dev, &dev_attr_in7_max);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_in7_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in7_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in7_max))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_in7_alarm.dev_attr)))
+ goto exit_remove;
} else {
- device_create_file(&new_client->dev, &dev_attr_fan2_input);
- device_create_file(&new_client->dev, &dev_attr_fan2_min);
- device_create_file(&new_client->dev, &dev_attr_fan2_div);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_fan2_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_fan2_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_fan2_div))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_fan2_alarm.dev_attr)))
+ goto exit_remove;
}
- device_create_file(&new_client->dev, &dev_attr_temp1_input);
- device_create_file(&new_client->dev, &dev_attr_temp1_max);
- device_create_file(&new_client->dev, &dev_attr_temp1_min);
- device_create_file(&new_client->dev, &dev_attr_temp1_crit);
- device_create_file(&new_client->dev, &dev_attr_temp2_input);
- device_create_file(&new_client->dev, &dev_attr_temp2_max);
- device_create_file(&new_client->dev, &dev_attr_temp2_min);
- device_create_file(&new_client->dev, &dev_attr_temp2_crit);
-
if (data->channel & CHAN_TEMP3) {
- device_create_file(&new_client->dev, &dev_attr_temp3_input);
- device_create_file(&new_client->dev, &dev_attr_temp3_max);
- device_create_file(&new_client->dev, &dev_attr_temp3_min);
- device_create_file(&new_client->dev, &dev_attr_temp3_crit);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_temp3_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_temp3_max))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_temp3_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_temp3_crit))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_temp3_alarm.dev_attr))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_temp3_fault.dev_attr)))
+ goto exit_remove;
} else {
- device_create_file(&new_client->dev, &dev_attr_in0_input);
- device_create_file(&new_client->dev, &dev_attr_in0_min);
- device_create_file(&new_client->dev, &dev_attr_in0_max);
- device_create_file(&new_client->dev, &dev_attr_in5_input);
- device_create_file(&new_client->dev, &dev_attr_in5_min);
- device_create_file(&new_client->dev, &dev_attr_in5_max);
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_in0_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in0_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in0_max))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_in0_alarm.dev_attr))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in5_input))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in5_min))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_in5_max))
+ || (err = device_create_file(&new_client->dev,
+ &sensor_dev_attr_in5_alarm.dev_attr)))
+ goto exit_remove;
}
if (!(data->channel & CHAN_NO_VID)) {
- device_create_file(&new_client->dev, &dev_attr_cpu0_vid);
- device_create_file(&new_client->dev, &dev_attr_vrm);
+ data->vrm = vid_which_vrm();
+ if ((err = device_create_file(&new_client->dev,
+ &dev_attr_cpu0_vid))
+ || (err = device_create_file(&new_client->dev,
+ &dev_attr_vrm)))
+ goto exit_remove;
}
- device_create_file(&new_client->dev, &dev_attr_alarms);
- device_create_file(&new_client->dev, &dev_attr_aout_output);
+ data->hwmon_dev = hwmon_device_register(&new_client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
return 0;
-exit_detach:
- i2c_detach_client(new_client);
+exit_remove:
+ sysfs_remove_group(&new_client->dev.kobj, &lm87_group);
+ sysfs_remove_group(&new_client->dev.kobj, &lm87_group_opt);
exit_free:
+ lm87_write_value(new_client, LM87_REG_CONFIG, data->config);
kfree(data);
exit:
return err;
static void lm87_init_client(struct i2c_client *client)
{
struct lm87_data *data = i2c_get_clientdata(client);
- u8 config;
- data->channel = lm87_read_value(client, LM87_REG_CHANNEL_MODE);
- data->vrm = vid_which_vrm();
+ if (client->dev.platform_data) {
+ data->channel = *(u8 *)client->dev.platform_data;
+ lm87_write_value(client,
+ LM87_REG_CHANNEL_MODE, data->channel);
+ } else {
+ data->channel = lm87_read_value(client, LM87_REG_CHANNEL_MODE);
+ }
+ data->config = lm87_read_value(client, LM87_REG_CONFIG) & 0x6F;
- config = lm87_read_value(client, LM87_REG_CONFIG);
- if (!(config & 0x01)) {
+ if (!(data->config & 0x01)) {
int i;
/* Limits are left uninitialized after power-up */
lm87_write_value(client, LM87_REG_IN_MAX(0), 0xFF);
}
}
- if ((config & 0x81) != 0x01) {
- /* Start monitoring */
+
+ /* Make sure Start is set and INT#_Clear is clear */
+ if ((data->config & 0x09) != 0x01)
lm87_write_value(client, LM87_REG_CONFIG,
- (config & 0xF7) | 0x01);
- }
+ (data->config & 0x77) | 0x01);
}
-static int lm87_detach_client(struct i2c_client *client)
+static int lm87_remove(struct i2c_client *client)
{
struct lm87_data *data = i2c_get_clientdata(client);
- int err;
-
- hwmon_device_unregister(data->class_dev);
- if ((err = i2c_detach_client(client)))
- return err;
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &lm87_group);
+ sysfs_remove_group(&client->dev.kobj, &lm87_group_opt);
+ lm87_write_value(client, LM87_REG_CONFIG, data->config);
kfree(data);
return 0;
}