Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
- This driver supports the sensor part of the custom Abit uGuru chip found
- on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM /
- etc voltage & frequency control is not supported!
+ This driver supports the sensor part of the first and second revision of
+ the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
+ of lack of specs the CPU/RAM voltage & frequency control is not supported!
*/
#include <linux/module.h>
+#include <linux/sched.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/mutex.h>
#include <linux/err.h>
+#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
-#include <asm/io.h>
+#include <linux/dmi.h>
+#include <linux/io.h>
/* Banks */
#define ABIT_UGURU_ALARM_BANK 0x20 /* 1x 3 bytes */
#define ABIT_UGURU_SENSOR_BANK1 0x21 /* 16x volt and temp */
#define ABIT_UGURU_FAN_PWM 0x24 /* 3x 5 bytes */
#define ABIT_UGURU_SENSOR_BANK2 0x26 /* fans */
+/* max nr of sensors in bank1, a bank1 sensor can be in, temp or nc */
+#define ABIT_UGURU_MAX_BANK1_SENSORS 16
+/* Warning if you increase one of the 2 MAX defines below to 10 or higher you
+ should adjust the belonging _NAMES_LENGTH macro for the 2 digit number! */
/* max nr of sensors in bank2, currently mb's with max 6 fans are known */
#define ABIT_UGURU_MAX_BANK2_SENSORS 6
/* max nr of pwm outputs, currently mb's with max 5 pwm outputs are known */
#define ABIT_UGURU_IN_SENSOR 0
#define ABIT_UGURU_TEMP_SENSOR 1
#define ABIT_UGURU_NC 2
-/* Timeouts / Retries, if these turn out to need a lot of fiddling we could
- convert them to params. */
-/* 250 was determined by trial and error, 200 works most of the time, but not
- always. I assume this is cpu-speed independent, since the ISA-bus and not
- the CPU should be the bottleneck. Note that 250 sometimes is still not
- enough (only reported on AN7 mb) this is handled by a higher layer. */
-#define ABIT_UGURU_WAIT_TIMEOUT 250
+/* In many cases we need to wait for the uGuru to reach a certain status, most
+ of the time it will reach this status within 30 - 90 ISA reads, and thus we
+ can best busy wait. This define gives the total amount of reads to try. */
+#define ABIT_UGURU_WAIT_TIMEOUT 125
+/* However sometimes older versions of the uGuru seem to be distracted and they
+ do not respond for a long time. To handle this we sleep before each of the
+ last ABIT_UGURU_WAIT_TIMEOUT_SLEEP tries. */
+#define ABIT_UGURU_WAIT_TIMEOUT_SLEEP 5
/* Normally all expected status in abituguru_ready, are reported after the
- first read, but sometimes not and we need to poll, 5 polls was not enough
- 50 sofar is. */
-#define ABIT_UGURU_READY_TIMEOUT 50
+ first read, but sometimes not and we need to poll. */
+#define ABIT_UGURU_READY_TIMEOUT 5
/* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */
#define ABIT_UGURU_MAX_RETRIES 3
#define ABIT_UGURU_RETRY_DELAY (HZ/5)
-/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is a error */
+/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is an error */
#define ABIT_UGURU_MAX_TIMEOUTS 2
-
-/* All the variables below are named identical to the oguru and oguru2 programs
+/* utility macros */
+#define ABIT_UGURU_NAME "abituguru"
+#define ABIT_UGURU_DEBUG(level, format, arg...) \
+ if (level <= verbose) \
+ printk(KERN_DEBUG ABIT_UGURU_NAME ": " format , ## arg)
+/* Macros to help calculate the sysfs_names array length */
+/* sum of strlen of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
+ in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0 */
+#define ABITUGURU_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14)
+/* sum of strlen of: temp??_input\0, temp??_max\0, temp??_crit\0,
+ temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0 */
+#define ABITUGURU_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16)
+/* sum of strlen of: fan?_input\0, fan?_min\0, fan?_alarm\0,
+ fan?_alarm_enable\0, fan?_beep\0, fan?_shutdown\0 */
+#define ABITUGURU_FAN_NAMES_LENGTH (11 + 9 + 11 + 18 + 10 + 14)
+/* sum of strlen of: pwm?_enable\0, pwm?_auto_channels_temp\0,
+ pwm?_auto_point{1,2}_pwm\0, pwm?_auto_point{1,2}_temp\0 */
+#define ABITUGURU_PWM_NAMES_LENGTH (12 + 24 + 2 * 21 + 2 * 22)
+/* IN_NAMES_LENGTH > TEMP_NAMES_LENGTH so assume all bank1 sensors are in */
+#define ABITUGURU_SYSFS_NAMES_LENGTH ( \
+ ABIT_UGURU_MAX_BANK1_SENSORS * ABITUGURU_IN_NAMES_LENGTH + \
+ ABIT_UGURU_MAX_BANK2_SENSORS * ABITUGURU_FAN_NAMES_LENGTH + \
+ ABIT_UGURU_MAX_PWMS * ABITUGURU_PWM_NAMES_LENGTH)
+
+/* All the macros below are named identical to the oguru and oguru2 programs
reverse engineered by Olle Sandberg, hence the names might not be 100%
logical. I could come up with better names, but I prefer keeping the names
identical so that this driver can be compared with his work more easily. */
#define ABIT_UGURU_STATUS_READ 0x01 /* Ready to be read */
#define ABIT_UGURU_STATUS_INPUT 0x08 /* More input */
#define ABIT_UGURU_STATUS_READY 0x09 /* Ready to be written */
-/* utility macros */
-#define ABIT_UGURU_NAME "abituguru"
-#define ABIT_UGURU_DEBUG(level, format, arg...) \
- if (level <= verbose) \
- printk(KERN_DEBUG ABIT_UGURU_NAME ": " format , ## arg)
/* Constants */
/* in (Volt) sensors go up to 3494 mV, temp to 255000 millidegrees Celsius */
static int force;
module_param(force, bool, 0);
MODULE_PARM_DESC(force, "Set to one to force detection.");
+static int bank1_types[ABIT_UGURU_MAX_BANK1_SENSORS] = { -1, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 };
+module_param_array(bank1_types, int, NULL, 0);
+MODULE_PARM_DESC(bank1_types, "Bank1 sensortype autodetection override:\n"
+ " -1 autodetect\n"
+ " 0 volt sensor\n"
+ " 1 temp sensor\n"
+ " 2 not connected");
static int fan_sensors;
module_param(fan_sensors, int, 0);
MODULE_PARM_DESC(fan_sensors, "Number of fan sensors on the uGuru "
The structure is dynamically allocated, at the same time when a new
abituguru device is allocated. */
struct abituguru_data {
- struct class_device *class_dev; /* hwmon registered device */
+ struct device *hwmon_dev; /* hwmon registered device */
struct mutex update_lock; /* protect access to data and uGuru */
unsigned long last_updated; /* In jiffies */
unsigned short addr; /* uguru base address */
of a sensor is a volt or a temp sensor, for bank2 and the pwms its
easier todo things the same way. For in sensors we have 9 (temp 7)
sysfs entries per sensor, for bank2 and pwms 6. */
- struct sensor_device_attribute_2 sysfs_attr[16 * 9 +
+ struct sensor_device_attribute_2 sysfs_attr[
+ ABIT_UGURU_MAX_BANK1_SENSORS * 9 +
ABIT_UGURU_MAX_BANK2_SENSORS * 6 + ABIT_UGURU_MAX_PWMS * 6];
- /* Buffer to store the dynamically generated sysfs names, we need 2120
- bytes for bank1 (worst case scenario of 16 in sensors), 444 bytes
- for fan1-6 and 738 bytes for pwm1-6 + some room to spare in case I
- miscounted :) */
- char bank1_names[3400];
+ /* Buffer to store the dynamically generated sysfs names */
+ char sysfs_names[ABITUGURU_SYSFS_NAMES_LENGTH];
/* Bank 1 data */
- u8 bank1_sensors[2]; /* number of [0] in, [1] temp sensors */
- u8 bank1_address[2][16];/* addresses of [0] in, [1] temp sensors */
- u8 bank1_value[16];
- /* This array holds 16 x 3 entries for all the bank 1 sensor settings
+ /* number of and addresses of [0] in, [1] temp sensors */
+ u8 bank1_sensors[2];
+ u8 bank1_address[2][ABIT_UGURU_MAX_BANK1_SENSORS];
+ u8 bank1_value[ABIT_UGURU_MAX_BANK1_SENSORS];
+ /* This array holds 3 entries per sensor for the bank 1 sensor settings
(flags, min, max for voltage / flags, warn, shutdown for temp). */
- u8 bank1_settings[16][3];
+ u8 bank1_settings[ABIT_UGURU_MAX_BANK1_SENSORS][3];
/* Maximum value for each sensor used for scaling in mV/millidegrees
Celsius. */
- int bank1_max_value[16];
+ int bank1_max_value[ABIT_UGURU_MAX_BANK1_SENSORS];
/* Bank 2 data, ABIT_UGURU_MAX_BANK2_SENSORS entries for bank2 */
u8 bank2_sensors; /* actual number of bank2 sensors found */
timeout--;
if (timeout == 0)
return -EBUSY;
+ /* sleep a bit before our last few tries, see the comment on
+ this where ABIT_UGURU_WAIT_TIMEOUT_SLEEP is defined. */
+ if (timeout <= ABIT_UGURU_WAIT_TIMEOUT_SLEEP)
+ msleep(0);
}
return 0;
}
"CMD reg does not hold 0xAC after ready command\n");
return -EIO;
}
+ msleep(0);
}
/* After this the ABIT_UGURU_DATA port should contain
"state != more input after ready command\n");
return -EIO;
}
+ msleep(0);
}
data->uguru_ready = 1;
/* And read the data */
for (i = 0; i < count; i++) {
if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
- ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
+ ABIT_UGURU_DEBUG(retries ? 1 : 3,
+ "timeout exceeded waiting for "
"read state (bank: %d, sensor: %d)\n",
(int)bank_addr, (int)sensor_addr);
break;
static int abituguru_write(struct abituguru_data *data,
u8 bank_addr, u8 sensor_addr, u8 *buf, int count)
{
- int i;
+ /* We use the ready timeout as we have to wait for 0xAC just like the
+ ready function */
+ int i, timeout = ABIT_UGURU_READY_TIMEOUT;
/* Send the address */
i = abituguru_send_address(data, bank_addr, sensor_addr,
}
/* Now we need to wait till the chip is ready to be read again,
- don't ask why */
+ so that we can read 0xAC as confirmation that our write has
+ succeeded. */
if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state "
"after write (bank: %d, sensor: %d)\n", (int)bank_addr,
}
/* Cmd port MUST be read now and should contain 0xAC */
- if (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
- ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after write "
- "(bank: %d, sensor: %d)\n", (int)bank_addr,
- (int)sensor_addr);
- return -EIO;
+ while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
+ timeout--;
+ if (timeout == 0) {
+ ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after "
+ "write (bank: %d, sensor: %d)\n",
+ (int)bank_addr, (int)sensor_addr);
+ return -EIO;
+ }
+ msleep(0);
}
/* Last put the chip back in ready state */
abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
u8 sensor_addr)
{
- u8 val, buf[3];
- int ret = ABIT_UGURU_NC;
+ u8 val, test_flag, buf[3];
+ int i, ret = -ENODEV; /* error is the most common used retval :| */
+
+ /* If overriden by the user return the user selected type */
+ if (bank1_types[sensor_addr] >= ABIT_UGURU_IN_SENSOR &&
+ bank1_types[sensor_addr] <= ABIT_UGURU_NC) {
+ ABIT_UGURU_DEBUG(2, "assuming sensor type %d for bank1 sensor "
+ "%d because of \"bank1_types\" module param\n",
+ bank1_types[sensor_addr], (int)sensor_addr);
+ return bank1_types[sensor_addr];
+ }
/* First read the sensor and the current settings */
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, sensor_addr, &val,
1, ABIT_UGURU_MAX_RETRIES) != 1)
- return -EIO;
+ return -ENODEV;
/* Test val is sane / usable for sensor type detection. */
- if ((val < 10u) || (val > 240u)) {
+ if ((val < 10u) || (val > 250u)) {
printk(KERN_WARNING ABIT_UGURU_NAME
": bank1-sensor: %d reading (%d) too close to limits, "
"unable to determine sensor type, skipping sensor\n",
ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
/* Volt sensor test, enable volt low alarm, set min value ridicously
- high. If its a volt sensor this should always give us an alarm. */
- buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
- buf[1] = 245;
- buf[2] = 250;
+ high, or vica versa if the reading is very high. If its a volt
+ sensor this should always give us an alarm. */
+ if (val <= 240u) {
+ buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
+ buf[1] = 245;
+ buf[2] = 250;
+ test_flag = ABIT_UGURU_VOLT_LOW_ALARM_FLAG;
+ } else {
+ buf[0] = ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE;
+ buf[1] = 5;
+ buf[2] = 10;
+ test_flag = ABIT_UGURU_VOLT_HIGH_ALARM_FLAG;
+ }
+
if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
buf, 3) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
/* Now we need 20 ms to give the uguru time to read the sensors
and raise a voltage alarm */
set_current_state(TASK_UNINTERRUPTIBLE);
/* Check for alarm and check the alarm is a volt low alarm. */
if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
ABIT_UGURU_MAX_RETRIES) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
sensor_addr, buf, 3,
ABIT_UGURU_MAX_RETRIES) != 3)
- return -EIO;
- if (buf[0] & ABIT_UGURU_VOLT_LOW_ALARM_FLAG) {
- /* Restore original settings */
- if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
- sensor_addr,
- data->bank1_settings[sensor_addr],
- 3) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
+ if (buf[0] & test_flag) {
ABIT_UGURU_DEBUG(2, " found volt sensor\n");
- return ABIT_UGURU_IN_SENSOR;
+ ret = ABIT_UGURU_IN_SENSOR;
+ goto abituguru_detect_bank1_sensor_type_exit;
} else
ABIT_UGURU_DEBUG(2, " alarm raised during volt "
- "sensor test, but volt low flag not set\n");
+ "sensor test, but volt range flag not set\n");
} else
ABIT_UGURU_DEBUG(2, " alarm not raised during volt sensor "
"test\n");
buf[2] = 10;
if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
buf, 3) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
/* Now we need 50 ms to give the uguru time to read the sensors
and raise a temp alarm */
set_current_state(TASK_UNINTERRUPTIBLE);
/* Check for alarm and check the alarm is a temp high alarm. */
if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
ABIT_UGURU_MAX_RETRIES) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
sensor_addr, buf, 3,
ABIT_UGURU_MAX_RETRIES) != 3)
- return -EIO;
+ goto abituguru_detect_bank1_sensor_type_exit;
if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) {
- ret = ABIT_UGURU_TEMP_SENSOR;
ABIT_UGURU_DEBUG(2, " found temp sensor\n");
+ ret = ABIT_UGURU_TEMP_SENSOR;
+ goto abituguru_detect_bank1_sensor_type_exit;
} else
ABIT_UGURU_DEBUG(2, " alarm raised during temp "
"sensor test, but temp high flag not set\n");
ABIT_UGURU_DEBUG(2, " alarm not raised during temp sensor "
"test\n");
- /* Restore original settings */
- if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
- data->bank1_settings[sensor_addr], 3) != 3)
- return -EIO;
-
+ ret = ABIT_UGURU_NC;
+abituguru_detect_bank1_sensor_type_exit:
+ /* Restore original settings, failing here is really BAD, it has been
+ reported that some BIOS-es hang when entering the uGuru menu with
+ invalid settings present in the uGuru, so we try this 3 times. */
+ for (i = 0; i < 3; i++)
+ if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
+ sensor_addr, data->bank1_settings[sensor_addr],
+ 3) == 3)
+ break;
+ if (i == 3) {
+ printk(KERN_ERR ABIT_UGURU_NAME
+ ": Fatal error could not restore original settings. "
+ "This should never happen please report this to the "
+ "abituguru maintainer (see MAINTAINERS)\n");
+ return -ENODEV;
+ }
return ret;
}
{
int i;
- if (fan_sensors) {
+ if (fan_sensors > 0 && fan_sensors <= ABIT_UGURU_MAX_BANK2_SENSORS) {
data->bank2_sensors = fan_sensors;
ABIT_UGURU_DEBUG(2, "assuming %d fan sensors because of "
"\"fan_sensors\" module param\n",
-0x08 enable beep
-0x01 enable alarm
All other bits should be 0, but on some motherboards
- 0x40 (bit 6) is also high, at least for fan1 */
- if ((!i && (data->bank2_settings[i][0] & ~0xC9)) ||
- (i && (data->bank2_settings[i][0] & ~0x89))) {
+ 0x40 (bit 6) is also high for some of the fans?? */
+ if (data->bank2_settings[i][0] & ~0xC9) {
ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
"to be a fan sensor: settings[0] = %02X\n",
i, (unsigned int)data->bank2_settings[i][0]);
{
int i, j;
- if (pwms) {
+ if (pwms > 0 && pwms <= ABIT_UGURU_MAX_PWMS) {
data->pwms = pwms;
ABIT_UGURU_DEBUG(2, "assuming %d PWM outputs because of "
"\"pwms\" module param\n", (int)data->pwms);
store_pwm_setting, 4, 0),
};
-static const struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
+static struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
};
static int __devinit abituguru_probe(struct platform_device *pdev)
{
struct abituguru_data *data;
- int i, j, res;
+ int i, j, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
char *sysfs_filename;
- int sysfs_attr_i = 0;
/* El weirdo probe order, to keep the sysfs order identical to the
BIOS and window-appliction listing order. */
- const u8 probe_order[16] = { 0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E,
- 0x02, 0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
+ const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
+ 0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
+ 0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
if (!(data = kzalloc(sizeof(struct abituguru_data), GFP_KERNEL)))
return -ENOMEM;
- testread / see if one really is there.
- make an in memory copy of all the uguru settings for future use. */
if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
- data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3) {
- kfree(data);
- return -ENODEV;
- }
+ data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3)
+ goto abituguru_probe_error;
- for (i = 0; i < 16; i++) {
+ for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, i,
&data->bank1_value[i], 1,
- ABIT_UGURU_MAX_RETRIES) != 1) {
- kfree(data);
- return -ENODEV;
- }
+ ABIT_UGURU_MAX_RETRIES) != 1)
+ goto abituguru_probe_error;
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1+1, i,
data->bank1_settings[i], 3,
- ABIT_UGURU_MAX_RETRIES) != 3) {
- kfree(data);
- return -ENODEV;
- }
+ ABIT_UGURU_MAX_RETRIES) != 3)
+ goto abituguru_probe_error;
}
/* Note: We don't know how many bank2 sensors / pwms there really are,
but in order to "detect" this we need to read the maximum amount
for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
&data->bank2_value[i], 1,
- ABIT_UGURU_MAX_RETRIES) != 1) {
- kfree(data);
- return -ENODEV;
- }
+ ABIT_UGURU_MAX_RETRIES) != 1)
+ goto abituguru_probe_error;
if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2+1, i,
data->bank2_settings[i], 2,
- ABIT_UGURU_MAX_RETRIES) != 2) {
- kfree(data);
- return -ENODEV;
- }
+ ABIT_UGURU_MAX_RETRIES) != 2)
+ goto abituguru_probe_error;
}
for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
if (abituguru_read(data, ABIT_UGURU_FAN_PWM, i,
data->pwm_settings[i], 5,
- ABIT_UGURU_MAX_RETRIES) != 5) {
- kfree(data);
- return -ENODEV;
- }
+ ABIT_UGURU_MAX_RETRIES) != 5)
+ goto abituguru_probe_error;
}
data->last_updated = jiffies;
/* Detect sensor types and fill the sysfs attr for bank1 */
- sysfs_filename = data->bank1_names;
- for (i = 0; i < 16; i++) {
+ sysfs_attr_i = 0;
+ sysfs_filename = data->sysfs_names;
+ sysfs_names_free = ABITUGURU_SYSFS_NAMES_LENGTH;
+ for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
res = abituguru_detect_bank1_sensor_type(data, probe_order[i]);
- if (res < 0) {
- kfree(data);
- return -ENODEV;
- }
+ if (res < 0)
+ goto abituguru_probe_error;
if (res == ABIT_UGURU_NC)
continue;
+ /* res 1 (temp) sensors have 7 sysfs entries, 0 (in) 9 */
for (j = 0; j < (res ? 7 : 9); j++) {
- const char *name_templ = abituguru_sysfs_bank1_templ[
- res][j].dev_attr.attr.name;
+ used = snprintf(sysfs_filename, sysfs_names_free,
+ abituguru_sysfs_bank1_templ[res][j].dev_attr.
+ attr.name, data->bank1_sensors[res] + res)
+ + 1;
data->sysfs_attr[sysfs_attr_i] =
abituguru_sysfs_bank1_templ[res][j];
data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
sysfs_filename;
- sysfs_filename += sprintf(sysfs_filename, name_templ,
- data->bank1_sensors[res] + res) + 1;
data->sysfs_attr[sysfs_attr_i].index = probe_order[i];
+ sysfs_filename += used;
+ sysfs_names_free -= used;
sysfs_attr_i++;
}
data->bank1_max_value[probe_order[i]] =
/* Detect number of sensors and fill the sysfs attr for bank2 (fans) */
abituguru_detect_no_bank2_sensors(data);
for (i = 0; i < data->bank2_sensors; i++) {
- for (j = 0; j < 6; j++) {
- const char *name_templ = abituguru_sysfs_fan_templ[j].
- dev_attr.attr.name;
+ for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_fan_templ); j++) {
+ used = snprintf(sysfs_filename, sysfs_names_free,
+ abituguru_sysfs_fan_templ[j].dev_attr.attr.name,
+ i + 1) + 1;
data->sysfs_attr[sysfs_attr_i] =
abituguru_sysfs_fan_templ[j];
data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
sysfs_filename;
- sysfs_filename += sprintf(sysfs_filename, name_templ,
- i + 1) + 1;
data->sysfs_attr[sysfs_attr_i].index = i;
+ sysfs_filename += used;
+ sysfs_names_free -= used;
sysfs_attr_i++;
}
}
/* Detect number of sensors and fill the sysfs attr for pwms */
abituguru_detect_no_pwms(data);
for (i = 0; i < data->pwms; i++) {
- for (j = 0; j < 6; j++) {
- const char *name_templ = abituguru_sysfs_pwm_templ[j].
- dev_attr.attr.name;
+ for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_pwm_templ); j++) {
+ used = snprintf(sysfs_filename, sysfs_names_free,
+ abituguru_sysfs_pwm_templ[j].dev_attr.attr.name,
+ i + 1) + 1;
data->sysfs_attr[sysfs_attr_i] =
abituguru_sysfs_pwm_templ[j];
data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
sysfs_filename;
- sysfs_filename += sprintf(sysfs_filename, name_templ,
- i + 1) + 1;
data->sysfs_attr[sysfs_attr_i].index = i;
+ sysfs_filename += used;
+ sysfs_names_free -= used;
sysfs_attr_i++;
}
}
- /* Last add any "generic" entries to sysfs */
- for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) {
- data->sysfs_attr[sysfs_attr_i] = abituguru_sysfs_attr[i];
- sysfs_attr_i++;
+ /* Fail safe check, this should never happen! */
+ if (sysfs_names_free < 0) {
+ printk(KERN_ERR ABIT_UGURU_NAME ": Fatal error ran out of "
+ "space for sysfs attr names. This should never "
+ "happen please report to the abituguru maintainer "
+ "(see MAINTAINERS)\n");
+ res = -ENAMETOOLONG;
+ goto abituguru_probe_error;
}
printk(KERN_INFO ABIT_UGURU_NAME ": found Abit uGuru\n");
/* Register sysfs hooks */
- data->class_dev = hwmon_device_register(&pdev->dev);
- if (IS_ERR(data->class_dev)) {
- kfree(data);
- return PTR_ERR(data->class_dev);
- }
for (i = 0; i < sysfs_attr_i; i++)
- device_create_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
-
- return 0;
+ if (device_create_file(&pdev->dev,
+ &data->sysfs_attr[i].dev_attr))
+ goto abituguru_probe_error;
+ for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
+ if (device_create_file(&pdev->dev,
+ &abituguru_sysfs_attr[i].dev_attr))
+ goto abituguru_probe_error;
+
+ data->hwmon_dev = hwmon_device_register(&pdev->dev);
+ if (!IS_ERR(data->hwmon_dev))
+ return 0; /* success */
+
+ res = PTR_ERR(data->hwmon_dev);
+abituguru_probe_error:
+ for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+ device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+ for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
+ device_remove_file(&pdev->dev,
+ &abituguru_sysfs_attr[i].dev_attr);
+ platform_set_drvdata(pdev, NULL);
+ kfree(data);
+ return res;
}
static int __devexit abituguru_remove(struct platform_device *pdev)
{
+ int i;
struct abituguru_data *data = platform_get_drvdata(pdev);
+ hwmon_device_unregister(data->hwmon_dev);
+ for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+ device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+ for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
+ device_remove_file(&pdev->dev,
+ &abituguru_sysfs_attr[i].dev_attr);
platform_set_drvdata(pdev, NULL);
- hwmon_device_unregister(data->class_dev);
kfree(data);
return 0;
if ((err = abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
data->alarms, 3, 0)) != 3)
goto LEAVE_UPDATE;
- for (i = 0; i < 16; i++) {
+ for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
if ((err = abituguru_read(data,
ABIT_UGURU_SENSOR_BANK1, i,
&data->bank1_value[i], 1, 0)) != 1)
data->update_timeouts = 0;
LEAVE_UPDATE:
/* handle timeout condition */
- if (err == -EBUSY) {
+ if (!success && (err == -EBUSY || err >= 0)) {
/* No overflow please */
if (data->update_timeouts < 255u)
data->update_timeouts++;
return NULL;
}
+#ifdef CONFIG_PM
+static int abituguru_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct abituguru_data *data = platform_get_drvdata(pdev);
+ /* make sure all communications with the uguru are done and no new
+ ones are started */
+ mutex_lock(&data->update_lock);
+ return 0;
+}
+
+static int abituguru_resume(struct platform_device *pdev)
+{
+ struct abituguru_data *data = platform_get_drvdata(pdev);
+ /* See if the uGuru is still ready */
+ if (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT)
+ data->uguru_ready = 0;
+ mutex_unlock(&data->update_lock);
+ return 0;
+}
+#else
+#define abituguru_suspend NULL
+#define abituguru_resume NULL
+#endif /* CONFIG_PM */
+
static struct platform_driver abituguru_driver = {
.driver = {
.owner = THIS_MODULE,
.name = ABIT_UGURU_NAME,
},
- .probe = abituguru_probe,
- .remove = __devexit_p(abituguru_remove),
+ .probe = abituguru_probe,
+ .remove = __devexit_p(abituguru_remove),
+ .suspend = abituguru_suspend,
+ .resume = abituguru_resume,
};
static int __init abituguru_detect(void)
int address, err;
struct resource res = { .flags = IORESOURCE_IO };
+#ifdef CONFIG_DMI
+ const char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
+
+ /* safety check, refuse to load on non Abit motherboards */
+ if (!force && (!board_vendor ||
+ strcmp(board_vendor, "http://www.abit.com.tw/")))
+ return -ENODEV;
+#endif
+
address = abituguru_detect();
if (address < 0)
return address;