# Hardware monitoring chip drivers configuration
#
-menu "Hardware Monitoring support"
-
-config HWMON
+menuconfig HWMON
tristate "Hardware Monitoring support"
+ depends on HAS_IOMEM
default y
help
Hardware monitoring devices let you monitor the hardware health
This support can also be built as a module. If so, the module
will be called hwmon.
+if HWMON
+
config HWMON_VID
tristate
default n
config SENSORS_ABITUGURU
- tristate "Abit uGuru"
- depends on HWMON && EXPERIMENTAL
+ tristate "Abit uGuru (rev 1 & 2)"
+ depends on X86 && EXPERIMENTAL
help
- If you say yes here you get support for the Abit uGuru chips
- sensor part. The voltage and frequency control parts of the Abit
- uGuru are not supported. The Abit uGuru chip can be found on Abit
- uGuru featuring motherboards (most modern Abit motherboards).
+ If you say yes here you get support for the sensor part of the first
+ and second revision of the Abit uGuru chip. The voltage and frequency
+ control parts of the Abit uGuru are not supported. The Abit uGuru
+ chip can be found on Abit uGuru featuring motherboards (most modern
+ Abit motherboards from before end 2005). For more info and a list
+ of which motherboards have which revision see
+ Documentation/hwmon/abituguru
This driver can also be built as a module. If so, the module
will be called abituguru.
+config SENSORS_ABITUGURU3
+ tristate "Abit uGuru (rev 3)"
+ depends on X86 && EXPERIMENTAL
+ help
+ If you say yes here you get support for the sensor part of the
+ third revision of the Abit uGuru chip. Only reading the sensors
+ and their settings is supported. The third revision of the Abit
+ uGuru chip can be found on recent Abit motherboards (since end
+ 2005). For more info and a list of which motherboards have which
+ revision see Documentation/hwmon/abituguru3
+
+ This driver can also be built as a module. If so, the module
+ will be called abituguru3.
+
+config SENSORS_AD7414
+ tristate "Analog Devices AD7414"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ AD7414 temperature monitoring chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad7414.
+
+config SENSORS_AD7418
+ tristate "Analog Devices AD7416, AD7417 and AD7418"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ AD7416, AD7417 and AD7418 temperature monitoring chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad7418.
+
+config SENSORS_ADCXX
+ tristate "National Semiconductor ADCxxxSxxx"
+ depends on SPI_MASTER && EXPERIMENTAL
+ help
+ If you say yes here you get support for the National Semiconductor
+ ADC<bb><c>S<sss> chip family, where
+ * bb is the resolution in number of bits (8, 10, 12)
+ * c is the number of channels (1, 2, 4, 8)
+ * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
+ kSPS and 101 for 1 MSPS)
+
+ Examples : ADC081S101, ADC124S501, ...
+
+ This driver can also be built as a module. If so, the module
+ will be called adcxx.
+
config SENSORS_ADM1021
tristate "Analog Devices ADM1021 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for Analog Devices ADM1021
and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A,
config SENSORS_ADM1025
tristate "Analog Devices ADM1025 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1025
config SENSORS_ADM1026
tristate "Analog Devices ADM1026 and compatibles"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1026
This driver can also be built as a module. If so, the module
will be called adm1026.
+config SENSORS_ADM1029
+ tristate "Analog Devices ADM1029"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for Analog Devices ADM1029
+ sensor chip.
+ Very rare chip, please let us know you use it.
+
+ This driver can also be built as a module. If so, the module
+ will be called adm1029.
+
config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for Analog Devices ADM1031
and ADM1030 sensor chips.
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
This driver can also be built as a module. If so, the module
will be called adm9240.
+config SENSORS_ADT7462
+ tristate "Analog Devices ADT7462"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ ADT7462 temperature monitoring chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called adt7462.
+
+config SENSORS_ADT7470
+ tristate "Analog Devices ADT7470"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ ADT7470 temperature monitoring chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called adt7470.
+
+config SENSORS_ADT7473
+ tristate "Analog Devices ADT7473"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ ADT7473 temperature monitoring chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called adt7473.
+
config SENSORS_K8TEMP
- tristate "AMD K8 processor sensor"
- depends on HWMON && X86 && PCI && EXPERIMENTAL
+ tristate "AMD Athlon64/FX or Opteron temperature sensor"
+ depends on X86 && PCI && EXPERIMENTAL
help
If you say yes here you get support for the temperature
- sensor(s) inside your AMD K8 CPU.
+ sensor(s) inside your CPU. Supported is whole AMD K8
+ microarchitecture. Please note that you will need at least
+ lm-sensors 2.10.1 for proper userspace support.
This driver can also be built as a module. If so, the module
will be called k8temp.
+config SENSORS_AMS
+ tristate "Apple Motion Sensor driver"
+ depends on PPC_PMAC && !PPC64 && INPUT && ((ADB_PMU && I2C = y) || (ADB_PMU && !I2C) || I2C) && EXPERIMENTAL
+ select INPUT_POLLDEV
+ help
+ Support for the motion sensor included in PowerBooks. Includes
+ implementations for PMU and I2C.
+
+ This driver can also be built as a module. If so, the module
+ will be called ams.
+
+config SENSORS_AMS_PMU
+ bool "PMU variant"
+ depends on SENSORS_AMS && ADB_PMU
+ default y
+ help
+ PMU variant of motion sensor, found in late 2005 PowerBooks.
+
+config SENSORS_AMS_I2C
+ bool "I2C variant"
+ depends on SENSORS_AMS && I2C
+ default y
+ help
+ I2C variant of motion sensor, found in early 2005 PowerBooks and
+ iBooks.
+
config SENSORS_ASB100
tristate "Asus ASB100 Bach"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on X86 && I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for the ASB100 Bach sensor
config SENSORS_ATXP1
tristate "Attansic ATXP1 VID controller"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for the Attansic ATXP1 VID
config SENSORS_DS1621
tristate "Dallas Semiconductor DS1621 and DS1625"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for Dallas Semiconductor
DS1621 and DS1625 sensor chips.
This driver can also be built as a module. If so, the module
will be called ds1621.
+config SENSORS_I5K_AMB
+ tristate "FB-DIMM AMB temperature sensor on Intel 5000 series chipsets"
+ depends on PCI && EXPERIMENTAL
+ help
+ If you say yes here you get support for FB-DIMM AMB temperature
+ monitoring chips on systems with the Intel 5000 series chipset.
+
+ This driver can also be built as a module. If so, the module
+ will be called i5k_amb.
+
config SENSORS_F71805F
- tristate "Fintek F71805F/FG"
- depends on HWMON && EXPERIMENTAL
+ tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
+ depends on EXPERIMENTAL
help
If you say yes here you get support for hardware monitoring
- features of the Fintek F71805F/FG chips.
+ features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
+ Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called f71805f.
+config SENSORS_F71882FG
+ tristate "Fintek F71882FG and F71883FG"
+ depends on EXPERIMENTAL
+ help
+ If you say yes here you get support for hardware monitoring
+ features of the Fintek F71882FG and F71883FG Super-I/O chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called f71882fg.
+
+config SENSORS_F75375S
+ tristate "Fintek F75375S/SP and F75373";
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for hardware monitoring
+ features of the Fintek F75375S/SP and F75373
+
+ This driver can also be built as a module. If so, the module
+ will be called f75375s.
+
config SENSORS_FSCHER
tristate "FSC Hermes"
- depends on HWMON && I2C
+ depends on X86 && I2C
help
If you say yes here you get support for Fujitsu Siemens
Computers Hermes sensor chips.
config SENSORS_FSCPOS
tristate "FSC Poseidon"
- depends on HWMON && I2C
+ depends on X86 && I2C
help
If you say yes here you get support for Fujitsu Siemens
Computers Poseidon sensor chips.
This driver can also be built as a module. If so, the module
will be called fscpos.
+config SENSORS_FSCHMD
+ tristate "FSC Poseidon, Scylla, Hermes, Heimdall and Heracles"
+ depends on X86 && I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for various Fujitsu Siemens
+ Computers sensor chips.
+
+ This is a new merged driver for FSC sensor chips which is intended
+ as a replacment for the fscpos, fscscy and fscher drivers and adds
+ support for several other FCS sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called fschmd.
+
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for Genesys Logic GL518SM
sensor chips.
config SENSORS_GL520SM
tristate "Genesys Logic GL520SM"
- depends on HWMON && I2C
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Genesys Logic GL520SM
This driver can also be built as a module. If so, the module
will be called gl520sm.
+config SENSORS_CORETEMP
+ tristate "Intel Core (2) Duo/Solo temperature sensor"
+ depends on X86 && EXPERIMENTAL
+ help
+ If you say yes here you get support for the temperature
+ sensor inside your CPU. Supported all are all known variants
+ of Intel Core family.
+
+config SENSORS_IBMAEM
+ tristate "IBM Active Energy Manager temperature/power sensors and control"
+ select IPMI_SI
+ depends on IPMI_HANDLER
+ help
+ If you say yes here you get support for the temperature and
+ power sensors and capping hardware in various IBM System X
+ servers that support Active Energy Manager. This includes
+ the x3350, x3550, x3650, x3655, x3755, x3850 M2, x3950 M2,
+ and certain HS2x/LS2x/QS2x blades.
+
+ This driver can also be built as a module. If so, the module
+ will be called ibmaem.
+
+config SENSORS_IBMPEX
+ tristate "IBM PowerExecutive temperature/power sensors"
+ select IPMI_SI
+ depends on IPMI_HANDLER
+ help
+ If you say yes here you get support for the temperature and
+ power sensors in various IBM System X servers that support
+ PowerExecutive. So far this includes the x3350, x3550, x3650,
+ x3655, and x3755; the x3800, x3850, and x3950 models that have
+ PCI Express; and some of the HS2x, LS2x, and QS2x blades.
+
+ This driver can also be built as a module. If so, the module
+ will be called ibmpex.
+
config SENSORS_IT87
tristate "ITE IT87xx and compatibles"
- depends on HWMON && I2C
- select I2C_ISA
select HWMON_VID
help
If you say yes here you get support for ITE IT8705F, IT8712F,
- IT8716F and IT8718F sensor chips, and the SiS960 clone.
+ IT8716F, IT8718F and IT8726F sensor chips, and the SiS960 clone.
This driver can also be built as a module. If so, the module
will be called it87.
config SENSORS_LM63
tristate "National Semiconductor LM63"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for the National Semiconductor
LM63 remote diode digital temperature sensor with integrated fan
config SENSORS_LM70
tristate "National Semiconductor LM70"
- depends on HWMON && SPI_MASTER && EXPERIMENTAL
+ depends on SPI_MASTER && EXPERIMENTAL
help
If you say yes here you get support for the National Semiconductor
LM70 digital temperature sensor chip.
config SENSORS_LM75
tristate "National Semiconductor LM75 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
help
- If you say yes here you get support for National Semiconductor LM75
- sensor chips and clones: Dallas Semiconductor DS75 and DS1775 (in
- 9-bit precision mode), and TelCom (now Microchip) TCN75.
+ If you say yes here you get support for one common type of
+ temperature sensor chip, with models including:
+
+ - Dallas Semiconductor DS75 and DS1775
+ - Maxim MAX6625 and MAX6626
+ - Microchip MCP980x
+ - National Semiconductor LM75
+ - NXP's LM75A
+ - ST Microelectronics STDS75
+ - TelCom (now Microchip) TCN75
+ - Texas Instruments TMP100, TMP101, TMP75, TMP175, TMP275
- The DS75 and DS1775 in 10- to 12-bit precision modes will require
- a force module parameter. The driver will not handle the extra
- precision anyhow.
+ This driver supports driver model based binding through board
+ specific I2C device tables.
+
+ It also supports the "legacy" style of driver binding. To use
+ that with some chips which don't replicate LM75 quirks exactly,
+ you may need the "force" module parameter.
This driver can also be built as a module. If so, the module
will be called lm75.
config SENSORS_LM77
tristate "National Semiconductor LM77"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for National Semiconductor LM77
sensor chips.
config SENSORS_LM78
tristate "National Semiconductor LM78 and compatibles"
- depends on HWMON && I2C
- select I2C_ISA
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM78,
config SENSORS_LM80
tristate "National Semiconductor LM80"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for National Semiconductor
LM80 sensor chips.
config SENSORS_LM83
tristate "National Semiconductor LM83 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for National Semiconductor
LM82 and LM83 sensor chips.
config SENSORS_LM85
tristate "National Semiconductor LM85 and compatibles"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM85
will be called lm85.
config SENSORS_LM87
- tristate "National Semiconductor LM87"
- depends on HWMON && I2C
+ tristate "National Semiconductor LM87 and compatibles"
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for National Semiconductor LM87
- sensor chips.
+ and Analog Devices ADM1024 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm87.
config SENSORS_LM90
tristate "National Semiconductor LM90 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for National Semiconductor LM90,
- LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657 and
- MAX6658 sensor chips.
-
- The Analog Devices ADT7461 sensor chip is also supported, but only
- if found in ADM1032 compatibility mode.
+ LM86, LM89 and LM99, Analog Devices ADM1032 and ADT7461, and Maxim
+ MAX6646, MAX6647, MAX6649, MAX6657, MAX6658, MAX6659, MAX6680 and
+ MAX6681 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm90.
config SENSORS_LM92
tristate "National Semiconductor LM92 and compatibles"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for National Semiconductor LM92
and Maxim MAX6635 sensor chips.
This driver can also be built as a module. If so, the module
will be called lm92.
+config SENSORS_LM93
+ tristate "National Semiconductor LM93 and compatibles"
+ depends on I2C
+ select HWMON_VID
+ help
+ If you say yes here you get support for National Semiconductor LM93
+ sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called lm93.
+
+config SENSORS_MAX1111
+ tristate "Maxim MAX1111 Multichannel, Serial 8-bit ADC chip"
+ depends on SPI_MASTER
+ help
+ Say y here to support Maxim's MAX1111 ADC chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called max1111.
+
config SENSORS_MAX1619
tristate "Maxim MAX1619 sensor chip"
- depends on HWMON && I2C
+ depends on I2C
help
If you say yes here you get support for MAX1619 sensor chip.
This driver can also be built as a module. If so, the module
will be called max1619.
+config SENSORS_MAX6650
+ tristate "Maxim MAX6650 sensor chip"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the MAX6650 / MAX6651
+ sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called max6650.
+
config SENSORS_PC87360
tristate "National Semiconductor PC87360 family"
- depends on HWMON && I2C && EXPERIMENTAL
- select I2C_ISA
select HWMON_VID
help
If you say yes here you get access to the hardware monitoring
This driver can also be built as a module. If so, the module
will be called pc87360.
+config SENSORS_PC87427
+ tristate "National Semiconductor PC87427"
+ depends on EXPERIMENTAL
+ help
+ If you say yes here you get access to the hardware monitoring
+ functions of the National Semiconductor PC87427 Super-I/O chip.
+ The chip has two distinct logical devices, one for fan speed
+ monitoring and control, and one for voltage and temperature
+ monitoring. Only fan speed monitoring is supported right now.
+
+ This driver can also be built as a module. If so, the module
+ will be called pc87427.
+
config SENSORS_SIS5595
tristate "Silicon Integrated Systems Corp. SiS5595"
- depends on HWMON && I2C && PCI && EXPERIMENTAL
- select I2C_ISA
+ depends on PCI
help
If you say yes here you get support for the integrated sensors in
SiS5595 South Bridges.
This driver can also be built as a module. If so, the module
will be called sis5595.
+config SENSORS_DME1737
+ tristate "SMSC DME1737, SCH311x and compatibles"
+ depends on I2C && EXPERIMENTAL
+ select HWMON_VID
+ help
+ If you say yes here you get support for the hardware monitoring
+ and fan control features of the SMSC DME1737, SCH311x, SCH5027, and
+ Asus A8000 Super-I/O chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called dme1737.
+
config SENSORS_SMSC47M1
tristate "SMSC LPC47M10x and compatibles"
- depends on HWMON && I2C
- select I2C_ISA
help
If you say yes here you get support for the integrated fan
monitoring and control capabilities of the SMSC LPC47B27x,
- LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x, LPC47M192 and
- LPC47M997 chips.
+ LPC47M10x, LPC47M112, LPC47M13x, LPC47M14x, LPC47M15x,
+ LPC47M192, LPC47M292 and LPC47M997 chips.
- The temperature and voltage sensor features of the LPC47M192
- and LPC47M997 are supported by another driver, select also
- "SMSC LPC47M192 and compatibles" below for those.
+ The temperature and voltage sensor features of the LPC47M15x,
+ LPC47M192, LPC47M292 and LPC47M997 are supported by another
+ driver, select also "SMSC LPC47M192 and compatibles" below for
+ those.
This driver can also be built as a module. If so, the module
will be called smsc47m1.
config SENSORS_SMSC47M192
tristate "SMSC LPC47M192 and compatibles"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for the temperature and
- voltage sensors of the SMSC LPC47M192 and LPC47M997 chips.
+ voltage sensors of the SMSC LPC47M192, LPC47M15x, LPC47M292
+ and LPC47M997 chips.
The fan monitoring and control capabilities of these chips
are supported by another driver, select
config SENSORS_SMSC47B397
tristate "SMSC LPC47B397-NC"
- depends on HWMON && I2C && EXPERIMENTAL
- select I2C_ISA
+ depends on EXPERIMENTAL
help
If you say yes here you get support for the SMSC LPC47B397-NC
sensor chip.
This driver can also be built as a module. If so, the module
will be called smsc47b397.
+config SENSORS_ADS7828
+ tristate "Texas Instruments ADS7828"
+ depends on I2C
+ help
+ If you say yes here you get support for Texas Instruments ADS7828
+ 12-bit 8-channel ADC device.
+
+ This driver can also be built as a module. If so, the module
+ will be called ads7828.
+
+config SENSORS_THMC50
+ tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for Texas Instruments THMC50
+ sensor chips and clones: the Analog Devices ADM1022.
+
+ This driver can also be built as a module. If so, the module
+ will be called thmc50.
+
config SENSORS_VIA686A
tristate "VIA686A"
- depends on HWMON && I2C && PCI
- select I2C_ISA
+ depends on PCI
help
If you say yes here you get support for the integrated sensors in
Via 686A/B South Bridges.
This driver can also be built as a module. If so, the module
will be called via686a.
+config SENSORS_VT1211
+ tristate "VIA VT1211"
+ depends on EXPERIMENTAL
+ select HWMON_VID
+ help
+ If you say yes here then you get support for hardware monitoring
+ features of the VIA VT1211 Super-I/O chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called vt1211.
+
config SENSORS_VT8231
tristate "VIA VT8231"
- depends on HWMON && I2C && PCI && EXPERIMENTAL
+ depends on PCI
select HWMON_VID
- select I2C_ISA
help
If you say yes here then you get support for the integrated sensors
in the VIA VT8231 device.
will be called vt8231.
config SENSORS_W83781D
- tristate "Winbond W83781D, W83782D, W83783S, W83627HF, Asus AS99127F"
- depends on HWMON && I2C
- select I2C_ISA
+ tristate "Winbond W83781D, W83782D, W83783S, Asus AS99127F"
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Winbond W8378x series
- of sensor chips: the W83781D, W83782D, W83783S and W83627HF,
- and the similar Asus AS99127F.
+ of sensor chips: the W83781D, W83782D and W83783S, and the similar
+ Asus AS99127F.
This driver can also be built as a module. If so, the module
will be called w83781d.
config SENSORS_W83791D
tristate "Winbond W83791D"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
select HWMON_VID
help
If you say yes here you get support for the Winbond W83791D chip.
config SENSORS_W83792D
tristate "Winbond W83792D"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for the Winbond W83792D chip.
This driver can also be built as a module. If so, the module
will be called w83792d.
+config SENSORS_W83793
+ tristate "Winbond W83793"
+ depends on I2C && EXPERIMENTAL
+ select HWMON_VID
+ help
+ If you say yes here you get support for the Winbond W83793
+ hardware monitoring chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called w83793.
+
config SENSORS_W83L785TS
tristate "Winbond W83L785TS-S"
- depends on HWMON && I2C && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for the Winbond W83L785TS-S
sensor chip, which is used on the Asus A7N8X, among other
This driver can also be built as a module. If so, the module
will be called w83l785ts.
+config SENSORS_W83L786NG
+ tristate "Winbond W83L786NG, W83L786NR"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Winbond W83L786NG
+ and W83L786NR sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called w83l786ng.
+
config SENSORS_W83627HF
tristate "Winbond W83627HF, W83627THF, W83637HF, W83687THF, W83697HF"
- depends on HWMON && I2C
- select I2C_ISA
select HWMON_VID
help
If you say yes here you get support for the Winbond W836X7 series
will be called w83627hf.
config SENSORS_W83627EHF
- tristate "Winbond W83627EHF"
- depends on HWMON && I2C && EXPERIMENTAL
- select I2C_ISA
+ tristate "Winbond W83627EHF/DHG"
+ select HWMON_VID
help
- If you say yes here you get preliminary support for the hardware
+ If you say yes here you get support for the hardware
monitoring functionality of the Winbond W83627EHF Super-I/O chip.
- Only fan and temperature inputs are supported at the moment, while
- the chip does much more than that.
This driver also supports the W83627EHG, which is the lead-free
- version of the W83627EHF.
+ version of the W83627EHF, and the W83627DHG, which is a similar
+ chip suited for specific Intel processors that use PECI such as
+ the Core 2 Duo.
This driver can also be built as a module. If so, the module
will be called w83627ehf.
+config SENSORS_ULTRA45
+ tristate "Sun Ultra45 PIC16F747"
+ depends on SPARC64
+ help
+ This driver provides support for the Ultra45 workstation environmental
+ sensors.
+
config SENSORS_HDAPS
tristate "IBM Hard Drive Active Protection System (hdaps)"
- depends on HWMON && INPUT && X86
+ depends on INPUT && X86
+ select INPUT_POLLDEV
default n
help
This driver provides support for the IBM Hard Drive Active Protection
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick.
+ If your ThinkPad is not recognized by the driver, please update to latest
+ BIOS. This is especially the case for some R52 ThinkPads.
+
Say Y here if you have an applicable laptop and want to experience
the awesome power of hdaps.
+config SENSORS_LIS3LV02D
+ tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer"
+ depends on ACPI && INPUT
+ default n
+ help
+ This driver provides support for the LIS3LV02Dx accelerometer. In
+ particular, it can be found in a number of HP laptops, which have the
+ "Mobile Data Protection System 3D" or "3D DriveGuard" feature. On such
+ systems the driver should load automatically (via ACPI). The
+ accelerometer might also be found in other systems, connected via SPI
+ or I2C. The accelerometer data is readable via
+ /sys/devices/platform/lis3lv02d.
+
+ This driver also provides an absolute input class device, allowing
+ the laptop to act as a pinball machine-esque joystick.
+
+ This driver can also be built as a module. If so, the module
+ will be called lis3lv02d.
+
+config SENSORS_APPLESMC
+ tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
+ depends on INPUT && X86
+ select NEW_LEDS
+ select LEDS_CLASS
+ select INPUT_POLLDEV
+ default n
+ help
+ This driver provides support for the Apple System Management
+ Controller, which provides an accelerometer (Apple Sudden Motion
+ Sensor), light sensors, temperature sensors, keyboard backlight
+ control and fan control.
+
+ Only Intel-based Apple's computers are supported (MacBook Pro,
+ MacBook, MacMini).
+
+ Data from the different sensors, keyboard backlight control and fan
+ control are accessible via sysfs.
+
+ This driver also provides an absolute input class device, allowing
+ the laptop to act as a pinball machine-esque joystick.
+
+ Say Y here if you have an applicable laptop and want to experience
+ the awesome power of applesmc.
+
config HWMON_DEBUG_CHIP
bool "Hardware Monitoring Chip debugging messages"
- depends on HWMON
default n
help
Say Y here if you want the I2C chip drivers to produce a bunch of
a problem with I2C support and want to see more of what is going
on.
-endmenu
+endif # HWMON