# GPIO infrastructure and expanders
#
-config HAVE_GPIO_LIB
+config ARCH_WANT_OPTIONAL_GPIOLIB
bool
help
+ Select this config option from the architecture Kconfig, if
+ it is possible to use gpiolib on the architecture, but let the
+ user decide whether to actually build it or not.
+ Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
+ not depend on GPIOs being available, but rather let the user
+ decide whether he needs it or not.
+
+config ARCH_REQUIRE_GPIOLIB
+ bool
+ select GPIOLIB
+ help
Platforms select gpiolib if they use this infrastructure
for all their GPIOs, usually starting with ones integrated
into SOC processors.
+ Selecting this from the architecture code will cause the gpiolib
+ code to always get built in.
-menu "GPIO Support"
- depends on HAVE_GPIO_LIB
+
+
+menuconfig GPIOLIB
+ bool "GPIO Support"
+ depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
+ select GENERIC_GPIO
+ help
+ This enables GPIO support through the generic GPIO library.
+ You only need to enable this, if you also want to enable
+ one or more of the GPIO expansion card drivers below.
+
+ If unsure, say N.
+
+if GPIOLIB
config DEBUG_GPIO
bool "Debug GPIO calls"
depends on DEBUG_KERNEL
help
Say Y here to add some extra checks and diagnostics to GPIO calls.
- The checks help ensure that GPIOs have been properly initialized
- before they are used and that sleeping calls aren not made from
- nonsleeping contexts. They can make bitbanged serial protocols
+ These checks help ensure that GPIOs have been properly initialized
+ before they are used, and that sleeping calls are not made from
+ non-sleeping contexts. They can make bitbanged serial protocols
slower. The diagnostics help catch the type of setup errors
that are most common when setting up new platforms or boards.
# put expanders in the right section, in alphabetical order
+config GPIO_MAX730X
+ tristate
+
+comment "Memory mapped GPIO expanders:"
+
+config GPIO_IT8761E
+ tristate "IT8761E GPIO support"
+ depends on GPIOLIB
+ help
+ Say yes here to support GPIO functionality of IT8761E super I/O chip.
+
+config GPIO_PL061
+ bool "PrimeCell PL061 GPIO support"
+ depends on ARM_AMBA
+ help
+ Say yes here to support the PrimeCell PL061 GPIO device
+
+config GPIO_XILINX
+ bool "Xilinx GPIO support"
+ depends on PPC_OF || MICROBLAZE
+ help
+ Say yes here to support the Xilinx FPGA GPIO device
+
+config GPIO_VR41XX
+ tristate "NEC VR4100 series General-purpose I/O Uint support"
+ depends on CPU_VR41XX
+ help
+ Say yes here to support the NEC VR4100 series General-purpose I/O Uint
+
+config GPIO_SCH
+ tristate "Intel SCH GPIO"
+ depends on GPIOLIB && PCI
+ select MFD_CORE
+ select LPC_SCH
+ help
+ Say yes here to support GPIO interface on Intel Poulsbo SCH.
+ The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
+ powered by the core power rail and are turned off during sleep
+ modes (S3 and higher). The remaining four GPIOs are powered by
+ the Intel SCH suspend power supply. These GPIOs remain
+ active during S3. The suspend powered GPIOs can be used to wake the
+ system from the Suspend-to-RAM state.
+
+ This driver can also be built as a module. If so, the module
+ will be called sch-gpio.
+
comment "I2C GPIO expanders:"
+config GPIO_MAX7300
+ tristate "Maxim MAX7300 GPIO expander"
+ depends on I2C
+ select GPIO_MAX730X
+ help
+ GPIO driver for Maxim MAX7301 I2C-based GPIO expander.
+
+config GPIO_MAX732X
+ tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
+ depends on I2C
+ help
+ Say yes here to support the MAX7319, MAX7320-7327 series of I2C
+ Port Expanders. Each IO port on these chips has a fixed role of
+ Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
+ Input and Output (designed by 'P'). The combinations are listed
+ below:
+
+ 8 bits: max7319 (8I), max7320 (8O), max7321 (8P),
+ max7322 (4I4O), max7323 (4P4O)
+
+ 16 bits: max7324 (8I8O), max7325 (8P8O),
+ max7326 (4I12O), max7327 (4P12O)
+
+ Board setup code must specify the model to use, and the start
+ number for these GPIOs.
+
config GPIO_PCA953X
- tristate "PCA953x, PCA955x, and MAX7310 I/O ports"
+ tristate "PCA953x, PCA955x, TCA64xx, and MAX7310 I/O ports"
depends on I2C
help
Say yes here to provide access to several register-oriented
4 bits: pca9536, pca9537
- 8 bits: max7310, pca9534, pca9538, pca9554, pca9557
+ 8 bits: max7310, pca9534, pca9538, pca9554, pca9557,
+ tca6408
- 16 bits: pca9535, pca9539, pca9555
+ 16 bits: pca9535, pca9539, pca9555, tca6416
This driver can also be built as a module. If so, the module
will be called pca953x.
+config GPIO_PCA953X_IRQ
+ bool "Interrupt controller support for PCA953x"
+ depends on GPIO_PCA953X=y
+ help
+ Say yes here to enable the pca953x to be used as an interrupt
+ controller. It requires the driver to be built in the kernel.
+
config GPIO_PCF857X
tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
depends on I2C
This driver provides an in-kernel interface to those GPIOs using
platform-neutral GPIO calls.
+config GPIO_TWL4030
+ tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
+ depends on TWL4030_CORE
+ help
+ Say yes here to access the GPIO signals of various multi-function
+ power management chips from Texas Instruments.
+
+config GPIO_WM831X
+ tristate "WM831x GPIOs"
+ depends on MFD_WM831X
+ help
+ Say yes here to access the GPIO signals of WM831x power management
+ chips from Wolfson Microelectronics.
+
+config GPIO_WM8350
+ tristate "WM8350 GPIOs"
+ depends on MFD_WM8350
+ help
+ Say yes here to access the GPIO signals of WM8350 power management
+ chips from Wolfson Microelectronics.
+
+config GPIO_WM8994
+ tristate "WM8994 GPIOs"
+ depends on MFD_WM8994
+ help
+ Say yes here to access the GPIO signals of WM8994 audio hub
+ CODECs from Wolfson Microelectronics.
+
+config GPIO_ADP5520
+ tristate "GPIO Support for ADP5520 PMIC"
+ depends on PMIC_ADP5520
+ help
+ This option enables support for on-chip GPIO found
+ on Analog Devices ADP5520 PMICs.
+
+ To compile this driver as a module, choose M here: the module will
+ be called adp5520-gpio.
+
+config GPIO_ADP5588
+ tristate "ADP5588 I2C GPIO expander"
+ depends on I2C
+ help
+ This option enables support for 18 GPIOs found
+ on Analog Devices ADP5588 GPIO Expanders.
+ To compile this driver as a module, choose M here: the module will be
+ called adp5588-gpio.
+
+comment "PCI GPIO expanders:"
+
+config GPIO_CS5535
+ tristate "AMD CS5535/CS5536 GPIO support"
+ depends on PCI && !CS5535_GPIO
+ help
+ The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
+ can be used for quite a number of things. The CS5535/6 is found on
+ AMD Geode and Lemote Yeeloong devices.
+
+ If unsure, say N.
+
+config GPIO_BT8XX
+ tristate "BT8XX GPIO abuser"
+ depends on PCI && VIDEO_BT848=n
+ help
+ The BT8xx frame grabber chip has 24 GPIO pins than can be abused
+ as a cheap PCI GPIO card.
+
+ This chip can be found on Miro, Hauppauge and STB TV-cards.
+
+ The card needs to be physically altered for using it as a
+ GPIO card. For more information on how to build a GPIO card
+ from a BT8xx TV card, see the documentation file at
+ Documentation/bt8xxgpio.txt
+
+ If unsure, say N.
+
+config GPIO_LANGWELL
+ bool "Intel Moorestown Platform Langwell GPIO support"
+ depends on PCI
+ help
+ Say Y here to support Intel Moorestown platform GPIO.
+
+config GPIO_TIMBERDALE
+ bool "Support for timberdale GPIO IP"
+ depends on MFD_TIMBERDALE && GPIOLIB && HAS_IOMEM
+ ---help---
+ Add support for the GPIO IP in the timberdale FPGA.
+
comment "SPI GPIO expanders:"
config GPIO_MAX7301
tristate "Maxim MAX7301 GPIO expander"
depends on SPI_MASTER
+ select GPIO_MAX730X
help
- gpio driver for Maxim MAX7301 SPI GPIO expander.
+ GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
config GPIO_MCP23S08
tristate "Microchip MCP23S08 I/O expander"
SPI driver for Microchip MCP23S08 I/O expander. This provides
a GPIO interface supporting inputs and outputs.
-endmenu
+config GPIO_MC33880
+ tristate "Freescale MC33880 high-side/low-side switch"
+ depends on SPI_MASTER
+ help
+ SPI driver for Freescale MC33880 high-side/low-side switch.
+ This provides GPIO interface supporting inputs and outputs.
+
+comment "AC97 GPIO expanders:"
+
+config GPIO_UCB1400
+ bool "Philips UCB1400 GPIO"
+ depends on UCB1400_CORE
+ help
+ This enables support for the Philips UCB1400 GPIO pins.
+ The UCB1400 is an AC97 audio codec.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ucb1400_gpio.
+
+endif