* and many others.
*/
+#include <linux/blkdev.h>
+#include <linux/bug.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
-#include <linux/mod_devicetable.h>
-#include <linux/device.h>
#include <linux/scatterlist.h>
-#include <linux/dma-mapping.h>
-#include <linux/blkdev.h>
#include <linux/string.h>
+#include <linux/stringify.h>
#include <linux/timer.h>
+#include <linux/workqueue.h>
+#include <asm/system.h>
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
-#include <scsi/scsi_dbg.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
-#include "fw-transaction.h"
-#include "fw-topology.h"
#include "fw-device.h"
+#include "fw-topology.h"
+#include "fw-transaction.h"
/*
* So far only bridges from Oxford Semiconductor are known to support
MODULE_PARM_DESC(exclusive_login, "Exclusive login to sbp2 device "
"(default = Y, use N for concurrent initiators)");
+/*
+ * Flags for firmware oddities
+ *
+ * - 128kB max transfer
+ * Limit transfer size. Necessary for some old bridges.
+ *
+ * - 36 byte inquiry
+ * When scsi_mod probes the device, let the inquiry command look like that
+ * from MS Windows.
+ *
+ * - skip mode page 8
+ * Suppress sending of mode_sense for mode page 8 if the device pretends to
+ * support the SCSI Primary Block commands instead of Reduced Block Commands.
+ *
+ * - fix capacity
+ * Tell sd_mod to correct the last sector number reported by read_capacity.
+ * Avoids access beyond actual disk limits on devices with an off-by-one bug.
+ * Don't use this with devices which don't have this bug.
+ *
+ * - delay inquiry
+ * Wait extra SBP2_INQUIRY_DELAY seconds after login before SCSI inquiry.
+ *
+ * - power condition
+ * Set the power condition field in the START STOP UNIT commands sent by
+ * sd_mod on suspend, resume, and shutdown (if manage_start_stop is on).
+ * Some disks need this to spin down or to resume properly.
+ *
+ * - override internal blacklist
+ * Instead of adding to the built-in blacklist, use only the workarounds
+ * specified in the module load parameter.
+ * Useful if a blacklist entry interfered with a non-broken device.
+ */
+#define SBP2_WORKAROUND_128K_MAX_TRANS 0x1
+#define SBP2_WORKAROUND_INQUIRY_36 0x2
+#define SBP2_WORKAROUND_MODE_SENSE_8 0x4
+#define SBP2_WORKAROUND_FIX_CAPACITY 0x8
+#define SBP2_WORKAROUND_DELAY_INQUIRY 0x10
+#define SBP2_INQUIRY_DELAY 12
+#define SBP2_WORKAROUND_POWER_CONDITION 0x20
+#define SBP2_WORKAROUND_OVERRIDE 0x100
+
+static int sbp2_param_workarounds;
+module_param_named(workarounds, sbp2_param_workarounds, int, 0644);
+MODULE_PARM_DESC(workarounds, "Work around device bugs (default = 0"
+ ", 128kB max transfer = " __stringify(SBP2_WORKAROUND_128K_MAX_TRANS)
+ ", 36 byte inquiry = " __stringify(SBP2_WORKAROUND_INQUIRY_36)
+ ", skip mode page 8 = " __stringify(SBP2_WORKAROUND_MODE_SENSE_8)
+ ", fix capacity = " __stringify(SBP2_WORKAROUND_FIX_CAPACITY)
+ ", delay inquiry = " __stringify(SBP2_WORKAROUND_DELAY_INQUIRY)
+ ", set power condition in start stop unit = "
+ __stringify(SBP2_WORKAROUND_POWER_CONDITION)
+ ", override internal blacklist = " __stringify(SBP2_WORKAROUND_OVERRIDE)
+ ", or a combination)");
+
/* I don't know why the SCSI stack doesn't define something like this... */
typedef void (*scsi_done_fn_t)(struct scsi_cmnd *);
static const char sbp2_driver_name[] = "sbp2";
-struct sbp2_device {
- struct kref kref;
- struct fw_unit *unit;
+/*
+ * We create one struct sbp2_logical_unit per SBP-2 Logical Unit Number Entry
+ * and one struct scsi_device per sbp2_logical_unit.
+ */
+struct sbp2_logical_unit {
+ struct sbp2_target *tgt;
+ struct list_head link;
struct fw_address_handler address_handler;
struct list_head orb_list;
- u64 management_agent_address;
+
u64 command_block_agent_address;
- u32 workarounds;
+ u16 lun;
int login_id;
/*
- * We cache these addresses and only update them once we've
- * logged in or reconnected to the sbp2 device. That way, any
- * IO to the device will automatically fail and get retried if
- * it happens in a window where the device is not ready to
- * handle it (e.g. after a bus reset but before we reconnect).
+ * The generation is updated once we've logged in or reconnected
+ * to the logical unit. Thus, I/O to the device will automatically
+ * fail and get retried if it happens in a window where the device
+ * is not ready, e.g. after a bus reset but before we reconnect.
*/
- int node_id;
- int address_high;
int generation;
-
int retries;
struct delayed_work work;
+ bool has_sdev;
+ bool blocked;
+};
+
+/*
+ * We create one struct sbp2_target per IEEE 1212 Unit Directory
+ * and one struct Scsi_Host per sbp2_target.
+ */
+struct sbp2_target {
+ struct kref kref;
+ struct fw_unit *unit;
+ const char *bus_id;
+ struct list_head lu_list;
+
+ u64 management_agent_address;
+ u64 guid;
+ int directory_id;
+ int node_id;
+ int address_high;
+ unsigned int workarounds;
+ unsigned int mgt_orb_timeout;
+ unsigned int max_payload;
+
+ int dont_block; /* counter for each logical unit */
+ int blocked; /* ditto */
};
-#define SBP2_MAX_SG_ELEMENT_LENGTH 0xf000
-#define SBP2_MAX_SECTORS 255 /* Max sectors supported */
-#define SBP2_ORB_TIMEOUT 2000 /* Timeout in ms */
+/* Impossible login_id, to detect logout attempt before successful login */
+#define INVALID_LOGIN_ID 0x10000
+/*
+ * Per section 7.4.8 of the SBP-2 spec, a mgt_ORB_timeout value can be
+ * provided in the config rom. Most devices do provide a value, which
+ * we'll use for login management orbs, but with some sane limits.
+ */
+#define SBP2_MIN_LOGIN_ORB_TIMEOUT 5000U /* Timeout in ms */
+#define SBP2_MAX_LOGIN_ORB_TIMEOUT 40000U /* Timeout in ms */
+#define SBP2_ORB_TIMEOUT 2000U /* Timeout in ms */
#define SBP2_ORB_NULL 0x80000000
+#define SBP2_RETRY_LIMIT 0xf /* 15 retries */
+#define SBP2_CYCLE_LIMIT (0xc8 << 12) /* 200 125us cycles */
-#define SBP2_DIRECTION_TO_MEDIA 0x0
-#define SBP2_DIRECTION_FROM_MEDIA 0x1
+/*
+ * The default maximum s/g segment size of a FireWire controller is
+ * usually 0x10000, but SBP-2 only allows 0xffff. Since buffers have to
+ * be quadlet-aligned, we set the length limit to 0xffff & ~3.
+ */
+#define SBP2_MAX_SEG_SIZE 0xfffc
/* Unit directory keys */
-#define SBP2_COMMAND_SET_SPECIFIER 0x38
-#define SBP2_COMMAND_SET 0x39
-#define SBP2_COMMAND_SET_REVISION 0x3b
-#define SBP2_FIRMWARE_REVISION 0x3c
-
-/* Flags for detected oddities and brokeness */
-#define SBP2_WORKAROUND_128K_MAX_TRANS 0x1
-#define SBP2_WORKAROUND_INQUIRY_36 0x2
-#define SBP2_WORKAROUND_MODE_SENSE_8 0x4
-#define SBP2_WORKAROUND_FIX_CAPACITY 0x8
-#define SBP2_WORKAROUND_OVERRIDE 0x100
+#define SBP2_CSR_UNIT_CHARACTERISTICS 0x3a
+#define SBP2_CSR_FIRMWARE_REVISION 0x3c
+#define SBP2_CSR_LOGICAL_UNIT_NUMBER 0x14
+#define SBP2_CSR_LOGICAL_UNIT_DIRECTORY 0xd4
/* Management orb opcodes */
#define SBP2_LOGIN_REQUEST 0x0
};
struct sbp2_pointer {
- u32 high;
- u32 low;
+ __be32 high;
+ __be32 low;
};
struct sbp2_orb {
struct fw_transaction t;
+ struct kref kref;
dma_addr_t request_bus;
int rcode;
struct sbp2_pointer pointer;
struct {
struct sbp2_pointer password;
struct sbp2_pointer response;
- u32 misc;
- u32 length;
+ __be32 misc;
+ __be32 length;
struct sbp2_pointer status_fifo;
} request;
__be32 response[4];
struct sbp2_status status;
};
-#define LOGIN_RESPONSE_GET_LOGIN_ID(v) ((v).misc & 0xffff)
-#define LOGIN_RESPONSE_GET_LENGTH(v) (((v).misc >> 16) & 0xffff)
-
struct sbp2_login_response {
- u32 misc;
+ __be32 misc;
struct sbp2_pointer command_block_agent;
- u32 reconnect_hold;
+ __be32 reconnect_hold;
};
#define COMMAND_ORB_DATA_SIZE(v) ((v))
#define COMMAND_ORB_PAGE_SIZE(v) ((v) << 16)
#define COMMAND_ORB_PAGE_TABLE_PRESENT ((1) << 19)
#define COMMAND_ORB_MAX_PAYLOAD(v) ((v) << 20)
#define COMMAND_ORB_SPEED(v) ((v) << 24)
-#define COMMAND_ORB_DIRECTION(v) ((v) << 27)
+#define COMMAND_ORB_DIRECTION ((1) << 27)
#define COMMAND_ORB_REQUEST_FORMAT(v) ((v) << 29)
#define COMMAND_ORB_NOTIFY ((1) << 31)
struct {
struct sbp2_pointer next;
struct sbp2_pointer data_descriptor;
- u32 misc;
+ __be32 misc;
u8 command_block[12];
} request;
struct scsi_cmnd *cmd;
scsi_done_fn_t done;
- struct fw_unit *unit;
+ struct sbp2_logical_unit *lu;
struct sbp2_pointer page_table[SG_ALL] __attribute__((aligned(8)));
dma_addr_t page_table_bus;
};
+#define SBP2_ROM_VALUE_WILDCARD ~0 /* match all */
+#define SBP2_ROM_VALUE_MISSING 0xff000000 /* not present in the unit dir. */
+
/*
* List of devices with known bugs.
*
* The firmware_revision field, masked with 0xffff00, is the best
* indicator for the type of bridge chip of a device. It yields a few
* false positives but this did not break correctly behaving devices
- * so far. We use ~0 as a wildcard, since the 24 bit values we get
- * from the config rom can never match that.
+ * so far.
*/
static const struct {
u32 firmware_revision;
u32 model;
- unsigned workarounds;
+ unsigned int workarounds;
} sbp2_workarounds_table[] = {
/* DViCO Momobay CX-1 with TSB42AA9 bridge */ {
.firmware_revision = 0x002800,
.model = 0x001010,
.workarounds = SBP2_WORKAROUND_INQUIRY_36 |
- SBP2_WORKAROUND_MODE_SENSE_8,
+ SBP2_WORKAROUND_MODE_SENSE_8 |
+ SBP2_WORKAROUND_POWER_CONDITION,
+ },
+ /* DViCO Momobay FX-3A with TSB42AA9A bridge */ {
+ .firmware_revision = 0x002800,
+ .model = 0x000000,
+ .workarounds = SBP2_WORKAROUND_DELAY_INQUIRY |
+ SBP2_WORKAROUND_POWER_CONDITION,
},
/* Initio bridges, actually only needed for some older ones */ {
.firmware_revision = 0x000200,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_INQUIRY_36,
},
+ /* PL-3507 bridge with Prolific firmware */ {
+ .firmware_revision = 0x012800,
+ .model = SBP2_ROM_VALUE_WILDCARD,
+ .workarounds = SBP2_WORKAROUND_POWER_CONDITION,
+ },
/* Symbios bridge */ {
.firmware_revision = 0xa0b800,
- .model = ~0,
+ .model = SBP2_ROM_VALUE_WILDCARD,
+ .workarounds = SBP2_WORKAROUND_128K_MAX_TRANS,
+ },
+ /* Datafab MD2-FW2 with Symbios/LSILogic SYM13FW500 bridge */ {
+ .firmware_revision = 0x002600,
+ .model = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_128K_MAX_TRANS,
},
-
/*
- * There are iPods (2nd gen, 3rd gen) with model_id == 0, but
- * these iPods do not feature the read_capacity bug according
- * to one report. Read_capacity behaviour as well as model_id
- * could change due to Apple-supplied firmware updates though.
+ * iPod 2nd generation: needs 128k max transfer size workaround
+ * iPod 3rd generation: needs fix capacity workaround
*/
-
- /* iPod 4th generation. */ {
+ {
+ .firmware_revision = 0x0a2700,
+ .model = 0x000000,
+ .workarounds = SBP2_WORKAROUND_128K_MAX_TRANS |
+ SBP2_WORKAROUND_FIX_CAPACITY,
+ },
+ /* iPod 4th generation */ {
.firmware_revision = 0x0a2700,
.model = 0x000021,
.workarounds = SBP2_WORKAROUND_FIX_CAPACITY,
},
/* iPod mini */ {
.firmware_revision = 0x0a2700,
+ .model = 0x000022,
+ .workarounds = SBP2_WORKAROUND_FIX_CAPACITY,
+ },
+ /* iPod mini */ {
+ .firmware_revision = 0x0a2700,
.model = 0x000023,
.workarounds = SBP2_WORKAROUND_FIX_CAPACITY,
},
}
};
-static void
-sbp2_status_write(struct fw_card *card, struct fw_request *request,
- int tcode, int destination, int source,
- int generation, int speed,
- unsigned long long offset,
- void *payload, size_t length, void *callback_data)
+static void free_orb(struct kref *kref)
{
- struct sbp2_device *sd = callback_data;
+ struct sbp2_orb *orb = container_of(kref, struct sbp2_orb, kref);
+
+ kfree(orb);
+}
+
+static void sbp2_status_write(struct fw_card *card, struct fw_request *request,
+ int tcode, int destination, int source,
+ int generation, int speed,
+ unsigned long long offset,
+ void *payload, size_t length, void *callback_data)
+{
+ struct sbp2_logical_unit *lu = callback_data;
struct sbp2_orb *orb;
struct sbp2_status status;
size_t header_size;
/* Lookup the orb corresponding to this status write. */
spin_lock_irqsave(&card->lock, flags);
- list_for_each_entry(orb, &sd->orb_list, link) {
+ list_for_each_entry(orb, &lu->orb_list, link) {
if (STATUS_GET_ORB_HIGH(status) == 0 &&
- STATUS_GET_ORB_LOW(status) == orb->request_bus &&
- orb->rcode == RCODE_COMPLETE) {
+ STATUS_GET_ORB_LOW(status) == orb->request_bus) {
+ orb->rcode = RCODE_COMPLETE;
list_del(&orb->link);
break;
}
}
spin_unlock_irqrestore(&card->lock, flags);
- if (&orb->link != &sd->orb_list)
+ if (&orb->link != &lu->orb_list)
orb->callback(orb, &status);
else
fw_error("status write for unknown orb\n");
+ kref_put(&orb->kref, free_orb);
+
fw_send_response(card, request, RCODE_COMPLETE);
}
-static void
-complete_transaction(struct fw_card *card, int rcode,
- void *payload, size_t length, void *data)
+static void complete_transaction(struct fw_card *card, int rcode,
+ void *payload, size_t length, void *data)
{
struct sbp2_orb *orb = data;
unsigned long flags;
- orb->rcode = rcode;
- if (rcode != RCODE_COMPLETE) {
- spin_lock_irqsave(&card->lock, flags);
+ /*
+ * This is a little tricky. We can get the status write for
+ * the orb before we get this callback. The status write
+ * handler above will assume the orb pointer transaction was
+ * successful and set the rcode to RCODE_COMPLETE for the orb.
+ * So this callback only sets the rcode if it hasn't already
+ * been set and only does the cleanup if the transaction
+ * failed and we didn't already get a status write.
+ */
+ spin_lock_irqsave(&card->lock, flags);
+
+ if (orb->rcode == -1)
+ orb->rcode = rcode;
+ if (orb->rcode != RCODE_COMPLETE) {
list_del(&orb->link);
spin_unlock_irqrestore(&card->lock, flags);
orb->callback(orb, NULL);
+ } else {
+ spin_unlock_irqrestore(&card->lock, flags);
}
+
+ kref_put(&orb->kref, free_orb);
}
-static void
-sbp2_send_orb(struct sbp2_orb *orb, struct fw_unit *unit,
- int node_id, int generation, u64 offset)
+static void sbp2_send_orb(struct sbp2_orb *orb, struct sbp2_logical_unit *lu,
+ int node_id, int generation, u64 offset)
{
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd = unit->device.driver_data;
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
unsigned long flags;
orb->pointer.high = 0;
- orb->pointer.low = orb->request_bus;
- fw_memcpy_to_be32(&orb->pointer, &orb->pointer, sizeof(orb->pointer));
+ orb->pointer.low = cpu_to_be32(orb->request_bus);
spin_lock_irqsave(&device->card->lock, flags);
- list_add_tail(&orb->link, &sd->orb_list);
+ list_add_tail(&orb->link, &lu->orb_list);
spin_unlock_irqrestore(&device->card->lock, flags);
+ /* Take a ref for the orb list and for the transaction callback. */
+ kref_get(&orb->kref);
+ kref_get(&orb->kref);
+
fw_send_request(device->card, &orb->t, TCODE_WRITE_BLOCK_REQUEST,
node_id, generation, device->max_speed, offset,
&orb->pointer, sizeof(orb->pointer),
complete_transaction, orb);
}
-static int sbp2_cancel_orbs(struct fw_unit *unit)
+static int sbp2_cancel_orbs(struct sbp2_logical_unit *lu)
{
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd = unit->device.driver_data;
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
struct sbp2_orb *orb, *next;
struct list_head list;
unsigned long flags;
INIT_LIST_HEAD(&list);
spin_lock_irqsave(&device->card->lock, flags);
- list_splice_init(&sd->orb_list, &list);
+ list_splice_init(&lu->orb_list, &list);
spin_unlock_irqrestore(&device->card->lock, flags);
list_for_each_entry_safe(orb, next, &list, link) {
return retval;
}
-static void
-complete_management_orb(struct sbp2_orb *base_orb, struct sbp2_status *status)
+static void complete_management_orb(struct sbp2_orb *base_orb,
+ struct sbp2_status *status)
{
struct sbp2_management_orb *orb =
container_of(base_orb, struct sbp2_management_orb, base);
complete(&orb->done);
}
-static int
-sbp2_send_management_orb(struct fw_unit *unit, int node_id, int generation,
- int function, int lun, void *response)
+static int sbp2_send_management_orb(struct sbp2_logical_unit *lu, int node_id,
+ int generation, int function,
+ int lun_or_login_id, void *response)
{
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd = unit->device.driver_data;
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
struct sbp2_management_orb *orb;
+ unsigned int timeout;
int retval = -ENOMEM;
+ if (function == SBP2_LOGOUT_REQUEST && fw_device_is_shutdown(device))
+ return 0;
+
orb = kzalloc(sizeof(*orb), GFP_ATOMIC);
if (orb == NULL)
return -ENOMEM;
- /*
- * The sbp2 device is going to send a block read request to
- * read out the request from host memory, so map it for dma.
- */
- orb->base.request_bus =
- dma_map_single(device->card->device, &orb->request,
- sizeof(orb->request), DMA_TO_DEVICE);
- if (dma_mapping_error(orb->base.request_bus))
- goto out;
-
+ kref_init(&orb->base.kref);
orb->response_bus =
dma_map_single(device->card->device, &orb->response,
sizeof(orb->response), DMA_FROM_DEVICE);
- if (dma_mapping_error(orb->response_bus))
- goto out;
+ if (dma_mapping_error(device->card->device, orb->response_bus))
+ goto fail_mapping_response;
- orb->request.response.high = 0;
- orb->request.response.low = orb->response_bus;
+ orb->request.response.high = 0;
+ orb->request.response.low = cpu_to_be32(orb->response_bus);
- orb->request.misc =
+ orb->request.misc = cpu_to_be32(
MANAGEMENT_ORB_NOTIFY |
MANAGEMENT_ORB_FUNCTION(function) |
- MANAGEMENT_ORB_LUN(lun);
- orb->request.length =
- MANAGEMENT_ORB_RESPONSE_LENGTH(sizeof(orb->response));
+ MANAGEMENT_ORB_LUN(lun_or_login_id));
+ orb->request.length = cpu_to_be32(
+ MANAGEMENT_ORB_RESPONSE_LENGTH(sizeof(orb->response)));
- orb->request.status_fifo.high = sd->address_handler.offset >> 32;
- orb->request.status_fifo.low = sd->address_handler.offset;
+ orb->request.status_fifo.high =
+ cpu_to_be32(lu->address_handler.offset >> 32);
+ orb->request.status_fifo.low =
+ cpu_to_be32(lu->address_handler.offset);
if (function == SBP2_LOGIN_REQUEST) {
- orb->request.misc |=
- MANAGEMENT_ORB_EXCLUSIVE(sbp2_param_exclusive_login) |
- MANAGEMENT_ORB_RECONNECT(0);
+ /* Ask for 2^2 == 4 seconds reconnect grace period */
+ orb->request.misc |= cpu_to_be32(
+ MANAGEMENT_ORB_RECONNECT(2) |
+ MANAGEMENT_ORB_EXCLUSIVE(sbp2_param_exclusive_login));
+ timeout = lu->tgt->mgt_orb_timeout;
+ } else {
+ timeout = SBP2_ORB_TIMEOUT;
}
- fw_memcpy_to_be32(&orb->request, &orb->request, sizeof(orb->request));
-
init_completion(&orb->done);
orb->base.callback = complete_management_orb;
- sbp2_send_orb(&orb->base, unit,
- node_id, generation, sd->management_agent_address);
+ orb->base.request_bus =
+ dma_map_single(device->card->device, &orb->request,
+ sizeof(orb->request), DMA_TO_DEVICE);
+ if (dma_mapping_error(device->card->device, orb->base.request_bus))
+ goto fail_mapping_request;
- wait_for_completion_timeout(&orb->done,
- msecs_to_jiffies(SBP2_ORB_TIMEOUT));
+ sbp2_send_orb(&orb->base, lu, node_id, generation,
+ lu->tgt->management_agent_address);
+
+ wait_for_completion_timeout(&orb->done, msecs_to_jiffies(timeout));
retval = -EIO;
- if (sbp2_cancel_orbs(unit) == 0) {
- fw_error("orb reply timed out, rcode=0x%02x\n",
- orb->base.rcode);
+ if (sbp2_cancel_orbs(lu) == 0) {
+ fw_error("%s: orb reply timed out, rcode=0x%02x\n",
+ lu->tgt->bus_id, orb->base.rcode);
goto out;
}
if (orb->base.rcode != RCODE_COMPLETE) {
- fw_error("management write failed, rcode 0x%02x\n",
- orb->base.rcode);
+ fw_error("%s: management write failed, rcode 0x%02x\n",
+ lu->tgt->bus_id, orb->base.rcode);
goto out;
}
if (STATUS_GET_RESPONSE(orb->status) != 0 ||
STATUS_GET_SBP_STATUS(orb->status) != 0) {
- fw_error("error status: %d:%d\n",
+ fw_error("%s: error status: %d:%d\n", lu->tgt->bus_id,
STATUS_GET_RESPONSE(orb->status),
STATUS_GET_SBP_STATUS(orb->status));
goto out;
out:
dma_unmap_single(device->card->device, orb->base.request_bus,
sizeof(orb->request), DMA_TO_DEVICE);
+ fail_mapping_request:
dma_unmap_single(device->card->device, orb->response_bus,
sizeof(orb->response), DMA_FROM_DEVICE);
-
+ fail_mapping_response:
if (response)
- fw_memcpy_from_be32(response,
- orb->response, sizeof(orb->response));
- kfree(orb);
+ memcpy(response, orb->response, sizeof(orb->response));
+ kref_put(&orb->base.kref, free_orb);
return retval;
}
-static void
-complete_agent_reset_write(struct fw_card *card, int rcode,
- void *payload, size_t length, void *data)
+static void sbp2_agent_reset(struct sbp2_logical_unit *lu)
{
- struct fw_transaction *t = data;
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
+ __be32 d = 0;
- kfree(t);
+ fw_run_transaction(device->card, TCODE_WRITE_QUADLET_REQUEST,
+ lu->tgt->node_id, lu->generation, device->max_speed,
+ lu->command_block_agent_address + SBP2_AGENT_RESET,
+ &d, sizeof(d));
}
-static int sbp2_agent_reset(struct fw_unit *unit)
+static void complete_agent_reset_write_no_wait(struct fw_card *card,
+ int rcode, void *payload, size_t length, void *data)
{
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd = unit->device.driver_data;
+ kfree(data);
+}
+
+static void sbp2_agent_reset_no_wait(struct sbp2_logical_unit *lu)
+{
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
struct fw_transaction *t;
- static u32 zero;
+ static __be32 d;
- t = kzalloc(sizeof(*t), GFP_ATOMIC);
+ t = kmalloc(sizeof(*t), GFP_ATOMIC);
if (t == NULL)
- return -ENOMEM;
+ return;
fw_send_request(device->card, t, TCODE_WRITE_QUADLET_REQUEST,
- sd->node_id, sd->generation, device->max_speed,
- sd->command_block_agent_address + SBP2_AGENT_RESET,
- &zero, sizeof(zero), complete_agent_reset_write, t);
+ lu->tgt->node_id, lu->generation, device->max_speed,
+ lu->command_block_agent_address + SBP2_AGENT_RESET,
+ &d, sizeof(d), complete_agent_reset_write_no_wait, t);
+}
- return 0;
+static inline void sbp2_allow_block(struct sbp2_logical_unit *lu)
+{
+ /*
+ * We may access dont_block without taking card->lock here:
+ * All callers of sbp2_allow_block() and all callers of sbp2_unblock()
+ * are currently serialized against each other.
+ * And a wrong result in sbp2_conditionally_block()'s access of
+ * dont_block is rather harmless, it simply misses its first chance.
+ */
+ --lu->tgt->dont_block;
}
-static void sbp2_reconnect(struct work_struct *work);
-static struct scsi_host_template scsi_driver_template;
+/*
+ * Blocks lu->tgt if all of the following conditions are met:
+ * - Login, INQUIRY, and high-level SCSI setup of all of the target's
+ * logical units have been finished (indicated by dont_block == 0).
+ * - lu->generation is stale.
+ *
+ * Note, scsi_block_requests() must be called while holding card->lock,
+ * otherwise it might foil sbp2_[conditionally_]unblock()'s attempt to
+ * unblock the target.
+ */
+static void sbp2_conditionally_block(struct sbp2_logical_unit *lu)
+{
+ struct sbp2_target *tgt = lu->tgt;
+ struct fw_card *card = fw_device(tgt->unit->device.parent)->card;
+ struct Scsi_Host *shost =
+ container_of((void *)tgt, struct Scsi_Host, hostdata[0]);
+ unsigned long flags;
-static void release_sbp2_device(struct kref *kref)
+ spin_lock_irqsave(&card->lock, flags);
+ if (!tgt->dont_block && !lu->blocked &&
+ lu->generation != card->generation) {
+ lu->blocked = true;
+ if (++tgt->blocked == 1)
+ scsi_block_requests(shost);
+ }
+ spin_unlock_irqrestore(&card->lock, flags);
+}
+
+/*
+ * Unblocks lu->tgt as soon as all its logical units can be unblocked.
+ * Note, it is harmless to run scsi_unblock_requests() outside the
+ * card->lock protected section. On the other hand, running it inside
+ * the section might clash with shost->host_lock.
+ */
+static void sbp2_conditionally_unblock(struct sbp2_logical_unit *lu)
{
- struct sbp2_device *sd = container_of(kref, struct sbp2_device, kref);
- struct Scsi_Host *host =
- container_of((void *)sd, struct Scsi_Host, hostdata[0]);
-
- scsi_remove_host(host);
- sbp2_send_management_orb(sd->unit, sd->node_id, sd->generation,
- SBP2_LOGOUT_REQUEST, sd->login_id, NULL);
- fw_core_remove_address_handler(&sd->address_handler);
- fw_notify("removed sbp2 unit %s\n", sd->unit->device.bus_id);
- put_device(&sd->unit->device);
- scsi_host_put(host);
+ struct sbp2_target *tgt = lu->tgt;
+ struct fw_card *card = fw_device(tgt->unit->device.parent)->card;
+ struct Scsi_Host *shost =
+ container_of((void *)tgt, struct Scsi_Host, hostdata[0]);
+ unsigned long flags;
+ bool unblock = false;
+
+ spin_lock_irqsave(&card->lock, flags);
+ if (lu->blocked && lu->generation == card->generation) {
+ lu->blocked = false;
+ unblock = --tgt->blocked == 0;
+ }
+ spin_unlock_irqrestore(&card->lock, flags);
+
+ if (unblock)
+ scsi_unblock_requests(shost);
}
+/*
+ * Prevents future blocking of tgt and unblocks it.
+ * Note, it is harmless to run scsi_unblock_requests() outside the
+ * card->lock protected section. On the other hand, running it inside
+ * the section might clash with shost->host_lock.
+ */
+static void sbp2_unblock(struct sbp2_target *tgt)
+{
+ struct fw_card *card = fw_device(tgt->unit->device.parent)->card;
+ struct Scsi_Host *shost =
+ container_of((void *)tgt, struct Scsi_Host, hostdata[0]);
+ unsigned long flags;
+
+ spin_lock_irqsave(&card->lock, flags);
+ ++tgt->dont_block;
+ spin_unlock_irqrestore(&card->lock, flags);
+
+ scsi_unblock_requests(shost);
+}
+
+static int sbp2_lun2int(u16 lun)
+{
+ struct scsi_lun eight_bytes_lun;
+
+ memset(&eight_bytes_lun, 0, sizeof(eight_bytes_lun));
+ eight_bytes_lun.scsi_lun[0] = (lun >> 8) & 0xff;
+ eight_bytes_lun.scsi_lun[1] = lun & 0xff;
+
+ return scsilun_to_int(&eight_bytes_lun);
+}
+
+static void sbp2_release_target(struct kref *kref)
+{
+ struct sbp2_target *tgt = container_of(kref, struct sbp2_target, kref);
+ struct sbp2_logical_unit *lu, *next;
+ struct Scsi_Host *shost =
+ container_of((void *)tgt, struct Scsi_Host, hostdata[0]);
+ struct scsi_device *sdev;
+ struct fw_device *device = fw_device(tgt->unit->device.parent);
+
+ /* prevent deadlocks */
+ sbp2_unblock(tgt);
+
+ list_for_each_entry_safe(lu, next, &tgt->lu_list, link) {
+ sdev = scsi_device_lookup(shost, 0, 0, sbp2_lun2int(lu->lun));
+ if (sdev) {
+ scsi_remove_device(sdev);
+ scsi_device_put(sdev);
+ }
+ if (lu->login_id != INVALID_LOGIN_ID) {
+ int generation, node_id;
+ /*
+ * tgt->node_id may be obsolete here if we failed
+ * during initial login or after a bus reset where
+ * the topology changed.
+ */
+ generation = device->generation;
+ smp_rmb(); /* node_id vs. generation */
+ node_id = device->node_id;
+ sbp2_send_management_orb(lu, node_id, generation,
+ SBP2_LOGOUT_REQUEST,
+ lu->login_id, NULL);
+ }
+ fw_core_remove_address_handler(&lu->address_handler);
+ list_del(&lu->link);
+ kfree(lu);
+ }
+ scsi_remove_host(shost);
+ fw_notify("released %s, target %d:0:0\n", tgt->bus_id, shost->host_no);
+
+ fw_unit_put(tgt->unit);
+ scsi_host_put(shost);
+ fw_device_put(device);
+}
+
+static struct workqueue_struct *sbp2_wq;
+
+static void sbp2_target_put(struct sbp2_target *tgt)
+{
+ kref_put(&tgt->kref, sbp2_release_target);
+}
+
+/*
+ * Always get the target's kref when scheduling work on one its units.
+ * Each workqueue job is responsible to call sbp2_target_put() upon return.
+ */
+static void sbp2_queue_work(struct sbp2_logical_unit *lu, unsigned long delay)
+{
+ kref_get(&lu->tgt->kref);
+ if (!queue_delayed_work(sbp2_wq, &lu->work, delay))
+ sbp2_target_put(lu->tgt);
+}
+
+/*
+ * Write retransmit retry values into the BUSY_TIMEOUT register.
+ * - The single-phase retry protocol is supported by all SBP-2 devices, but the
+ * default retry_limit value is 0 (i.e. never retry transmission). We write a
+ * saner value after logging into the device.
+ * - The dual-phase retry protocol is optional to implement, and if not
+ * supported, writes to the dual-phase portion of the register will be
+ * ignored. We try to write the original 1394-1995 default here.
+ * - In the case of devices that are also SBP-3-compliant, all writes are
+ * ignored, as the register is read-only, but contains single-phase retry of
+ * 15, which is what we're trying to set for all SBP-2 device anyway, so this
+ * write attempt is safe and yields more consistent behavior for all devices.
+ *
+ * See section 8.3.2.3.5 of the 1394-1995 spec, section 6.2 of the SBP-2 spec,
+ * and section 6.4 of the SBP-3 spec for further details.
+ */
+static void sbp2_set_busy_timeout(struct sbp2_logical_unit *lu)
+{
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
+ __be32 d = cpu_to_be32(SBP2_CYCLE_LIMIT | SBP2_RETRY_LIMIT);
+
+ fw_run_transaction(device->card, TCODE_WRITE_QUADLET_REQUEST,
+ lu->tgt->node_id, lu->generation, device->max_speed,
+ CSR_REGISTER_BASE + CSR_BUSY_TIMEOUT,
+ &d, sizeof(d));
+}
+
+static void sbp2_reconnect(struct work_struct *work);
+
static void sbp2_login(struct work_struct *work)
{
- struct sbp2_device *sd =
- container_of(work, struct sbp2_device, work.work);
- struct Scsi_Host *host =
- container_of((void *)sd, struct Scsi_Host, hostdata[0]);
- struct fw_unit *unit = sd->unit;
- struct fw_device *device = fw_device(unit->device.parent);
+ struct sbp2_logical_unit *lu =
+ container_of(work, struct sbp2_logical_unit, work.work);
+ struct sbp2_target *tgt = lu->tgt;
+ struct fw_device *device = fw_device(tgt->unit->device.parent);
+ struct Scsi_Host *shost;
+ struct scsi_device *sdev;
struct sbp2_login_response response;
- int generation, node_id, local_node_id, lun, retval;
+ int generation, node_id, local_node_id;
- /* FIXME: Make this work for multi-lun devices. */
- lun = 0;
+ if (fw_device_is_shutdown(device))
+ goto out;
+
+ generation = device->generation;
+ smp_rmb(); /* node IDs must not be older than generation */
+ node_id = device->node_id;
+ local_node_id = device->card->node_id;
- generation = device->card->generation;
- node_id = device->node->node_id;
- local_node_id = device->card->local_node->node_id;
+ /* If this is a re-login attempt, log out, or we might be rejected. */
+ if (lu->has_sdev)
+ sbp2_send_management_orb(lu, device->node_id, generation,
+ SBP2_LOGOUT_REQUEST, lu->login_id, NULL);
- if (sbp2_send_management_orb(unit, node_id, generation,
- SBP2_LOGIN_REQUEST, lun, &response) < 0) {
- if (sd->retries++ < 5) {
- schedule_delayed_work(&sd->work, DIV_ROUND_UP(HZ, 5));
+ if (sbp2_send_management_orb(lu, node_id, generation,
+ SBP2_LOGIN_REQUEST, lu->lun, &response) < 0) {
+ if (lu->retries++ < 5) {
+ sbp2_queue_work(lu, DIV_ROUND_UP(HZ, 5));
} else {
- fw_error("failed to login to %s\n",
- unit->device.bus_id);
- kref_put(&sd->kref, release_sbp2_device);
+ fw_error("%s: failed to login to LUN %04x\n",
+ tgt->bus_id, lu->lun);
+ /* Let any waiting I/O fail from now on. */
+ sbp2_unblock(lu->tgt);
}
- return;
+ goto out;
}
- sd->generation = generation;
- sd->node_id = node_id;
- sd->address_high = local_node_id << 16;
-
- /* Get command block agent offset and login id. */
- sd->command_block_agent_address =
- ((u64) (response.command_block_agent.high & 0xffff) << 32) |
- response.command_block_agent.low;
- sd->login_id = LOGIN_RESPONSE_GET_LOGIN_ID(response);
-
- fw_notify("logged in to sbp2 unit %s (%d retries)\n",
- unit->device.bus_id, sd->retries);
- fw_notify(" - management_agent_address: 0x%012llx\n",
- (unsigned long long) sd->management_agent_address);
- fw_notify(" - command_block_agent_address: 0x%012llx\n",
- (unsigned long long) sd->command_block_agent_address);
- fw_notify(" - status write address: 0x%012llx\n",
- (unsigned long long) sd->address_handler.offset);
-
-#if 0
- /* FIXME: The linux1394 sbp2 does this last step. */
- sbp2_set_busy_timeout(scsi_id);
-#endif
+ tgt->node_id = node_id;
+ tgt->address_high = local_node_id << 16;
+ smp_wmb(); /* node IDs must not be older than generation */
+ lu->generation = generation;
- PREPARE_DELAYED_WORK(&sd->work, sbp2_reconnect);
- sbp2_agent_reset(unit);
+ lu->command_block_agent_address =
+ ((u64)(be32_to_cpu(response.command_block_agent.high) & 0xffff)
+ << 32) | be32_to_cpu(response.command_block_agent.low);
+ lu->login_id = be32_to_cpu(response.misc) & 0xffff;
- /* FIXME: Loop over luns here. */
- lun = 0;
- retval = scsi_add_device(host, 0, 0, lun);
- if (retval < 0) {
- sbp2_send_management_orb(unit, sd->node_id, sd->generation,
- SBP2_LOGOUT_REQUEST, sd->login_id,
- NULL);
- /*
- * Set this back to sbp2_login so we fall back and
- * retry login on bus reset.
- */
- PREPARE_DELAYED_WORK(&sd->work, sbp2_login);
+ fw_notify("%s: logged in to LUN %04x (%d retries)\n",
+ tgt->bus_id, lu->lun, lu->retries);
+
+ /* set appropriate retry limit(s) in BUSY_TIMEOUT register */
+ sbp2_set_busy_timeout(lu);
+
+ PREPARE_DELAYED_WORK(&lu->work, sbp2_reconnect);
+ sbp2_agent_reset(lu);
+
+ /* This was a re-login. */
+ if (lu->has_sdev) {
+ sbp2_cancel_orbs(lu);
+ sbp2_conditionally_unblock(lu);
+ goto out;
}
- kref_put(&sd->kref, release_sbp2_device);
+
+ if (lu->tgt->workarounds & SBP2_WORKAROUND_DELAY_INQUIRY)
+ ssleep(SBP2_INQUIRY_DELAY);
+
+ shost = container_of((void *)tgt, struct Scsi_Host, hostdata[0]);
+ sdev = __scsi_add_device(shost, 0, 0, sbp2_lun2int(lu->lun), lu);
+ /*
+ * FIXME: We are unable to perform reconnects while in sbp2_login().
+ * Therefore __scsi_add_device() will get into trouble if a bus reset
+ * happens in parallel. It will either fail or leave us with an
+ * unusable sdev. As a workaround we check for this and retry the
+ * whole login and SCSI probing.
+ */
+
+ /* Reported error during __scsi_add_device() */
+ if (IS_ERR(sdev))
+ goto out_logout_login;
+
+ /* Unreported error during __scsi_add_device() */
+ smp_rmb(); /* get current card generation */
+ if (generation != device->card->generation) {
+ scsi_remove_device(sdev);
+ scsi_device_put(sdev);
+ goto out_logout_login;
+ }
+
+ /* No error during __scsi_add_device() */
+ lu->has_sdev = true;
+ scsi_device_put(sdev);
+ sbp2_allow_block(lu);
+ goto out;
+
+ out_logout_login:
+ smp_rmb(); /* generation may have changed */
+ generation = device->generation;
+ smp_rmb(); /* node_id must not be older than generation */
+
+ sbp2_send_management_orb(lu, device->node_id, generation,
+ SBP2_LOGOUT_REQUEST, lu->login_id, NULL);
+ /*
+ * If a bus reset happened, sbp2_update will have requeued
+ * lu->work already. Reset the work from reconnect to login.
+ */
+ PREPARE_DELAYED_WORK(&lu->work, sbp2_login);
+ out:
+ sbp2_target_put(tgt);
}
-static int sbp2_probe(struct device *dev)
+static int sbp2_add_logical_unit(struct sbp2_target *tgt, int lun_entry)
{
- struct fw_unit *unit = fw_unit(dev);
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd;
- struct fw_csr_iterator ci;
- struct Scsi_Host *host;
- int i, key, value, err;
- u32 model, firmware_revision;
+ struct sbp2_logical_unit *lu;
- err = -ENOMEM;
- host = scsi_host_alloc(&scsi_driver_template, sizeof(*sd));
- if (host == NULL)
- goto fail;
+ lu = kmalloc(sizeof(*lu), GFP_KERNEL);
+ if (!lu)
+ return -ENOMEM;
- sd = (struct sbp2_device *) host->hostdata;
- unit->device.driver_data = sd;
- sd->unit = unit;
- INIT_LIST_HEAD(&sd->orb_list);
- kref_init(&sd->kref);
+ lu->address_handler.length = 0x100;
+ lu->address_handler.address_callback = sbp2_status_write;
+ lu->address_handler.callback_data = lu;
- sd->address_handler.length = 0x100;
- sd->address_handler.address_callback = sbp2_status_write;
- sd->address_handler.callback_data = sd;
+ if (fw_core_add_address_handler(&lu->address_handler,
+ &fw_high_memory_region) < 0) {
+ kfree(lu);
+ return -ENOMEM;
+ }
- err = fw_core_add_address_handler(&sd->address_handler,
- &fw_high_memory_region);
- if (err < 0)
- goto fail_host;
+ lu->tgt = tgt;
+ lu->lun = lun_entry & 0xffff;
+ lu->login_id = INVALID_LOGIN_ID;
+ lu->retries = 0;
+ lu->has_sdev = false;
+ lu->blocked = false;
+ ++tgt->dont_block;
+ INIT_LIST_HEAD(&lu->orb_list);
+ INIT_DELAYED_WORK(&lu->work, sbp2_login);
+
+ list_add_tail(&lu->link, &tgt->lu_list);
+ return 0;
+}
- err = fw_device_enable_phys_dma(device);
- if (err < 0)
- goto fail_address_handler;
+static int sbp2_scan_logical_unit_dir(struct sbp2_target *tgt, u32 *directory)
+{
+ struct fw_csr_iterator ci;
+ int key, value;
- err = scsi_add_host(host, &unit->device);
- if (err < 0)
- goto fail_address_handler;
+ fw_csr_iterator_init(&ci, directory);
+ while (fw_csr_iterator_next(&ci, &key, &value))
+ if (key == SBP2_CSR_LOGICAL_UNIT_NUMBER &&
+ sbp2_add_logical_unit(tgt, value) < 0)
+ return -ENOMEM;
+ return 0;
+}
- /*
- * Scan unit directory to get management agent address,
- * firmware revison and model. Initialize firmware_revision
- * and model to values that wont match anything in our table.
- */
- firmware_revision = 0xff000000;
- model = 0xff000000;
- fw_csr_iterator_init(&ci, unit->directory);
+static int sbp2_scan_unit_dir(struct sbp2_target *tgt, u32 *directory,
+ u32 *model, u32 *firmware_revision)
+{
+ struct fw_csr_iterator ci;
+ int key, value;
+ unsigned int timeout;
+
+ fw_csr_iterator_init(&ci, directory);
while (fw_csr_iterator_next(&ci, &key, &value)) {
switch (key) {
+
case CSR_DEPENDENT_INFO | CSR_OFFSET:
- sd->management_agent_address =
- 0xfffff0000000ULL + 4 * value;
+ tgt->management_agent_address =
+ CSR_REGISTER_BASE + 4 * value;
break;
- case SBP2_FIRMWARE_REVISION:
- firmware_revision = value;
+
+ case CSR_DIRECTORY_ID:
+ tgt->directory_id = value;
break;
+
case CSR_MODEL:
- model = value;
+ *model = value;
+ break;
+
+ case SBP2_CSR_FIRMWARE_REVISION:
+ *firmware_revision = value;
+ break;
+
+ case SBP2_CSR_UNIT_CHARACTERISTICS:
+ /* the timeout value is stored in 500ms units */
+ timeout = ((unsigned int) value >> 8 & 0xff) * 500;
+ timeout = max(timeout, SBP2_MIN_LOGIN_ORB_TIMEOUT);
+ tgt->mgt_orb_timeout =
+ min(timeout, SBP2_MAX_LOGIN_ORB_TIMEOUT);
+
+ if (timeout > tgt->mgt_orb_timeout)
+ fw_notify("%s: config rom contains %ds "
+ "management ORB timeout, limiting "
+ "to %ds\n", tgt->bus_id,
+ timeout / 1000,
+ tgt->mgt_orb_timeout / 1000);
+ break;
+
+ case SBP2_CSR_LOGICAL_UNIT_NUMBER:
+ if (sbp2_add_logical_unit(tgt, value) < 0)
+ return -ENOMEM;
+ break;
+
+ case SBP2_CSR_LOGICAL_UNIT_DIRECTORY:
+ /* Adjust for the increment in the iterator */
+ if (sbp2_scan_logical_unit_dir(tgt, ci.p - 1 + value) < 0)
+ return -ENOMEM;
break;
}
}
+ return 0;
+}
+
+static void sbp2_init_workarounds(struct sbp2_target *tgt, u32 model,
+ u32 firmware_revision)
+{
+ int i;
+ unsigned int w = sbp2_param_workarounds;
+
+ if (w)
+ fw_notify("Please notify linux1394-devel@lists.sourceforge.net "
+ "if you need the workarounds parameter for %s\n",
+ tgt->bus_id);
+
+ if (w & SBP2_WORKAROUND_OVERRIDE)
+ goto out;
for (i = 0; i < ARRAY_SIZE(sbp2_workarounds_table); i++) {
+
if (sbp2_workarounds_table[i].firmware_revision !=
(firmware_revision & 0xffffff00))
continue;
+
if (sbp2_workarounds_table[i].model != model &&
- sbp2_workarounds_table[i].model != ~0)
+ sbp2_workarounds_table[i].model != SBP2_ROM_VALUE_WILDCARD)
continue;
- sd->workarounds |= sbp2_workarounds_table[i].workarounds;
+
+ w |= sbp2_workarounds_table[i].workarounds;
break;
}
-
- if (sd->workarounds)
- fw_notify("Workarounds for node %s: 0x%x "
+ out:
+ if (w)
+ fw_notify("Workarounds for %s: 0x%x "
"(firmware_revision 0x%06x, model_id 0x%06x)\n",
- unit->device.bus_id,
- sd->workarounds, firmware_revision, model);
+ tgt->bus_id, w, firmware_revision, model);
+ tgt->workarounds = w;
+}
+
+static struct scsi_host_template scsi_driver_template;
+
+static int sbp2_probe(struct device *dev)
+{
+ struct fw_unit *unit = fw_unit(dev);
+ struct fw_device *device = fw_device(unit->device.parent);
+ struct sbp2_target *tgt;
+ struct sbp2_logical_unit *lu;
+ struct Scsi_Host *shost;
+ u32 model, firmware_revision;
+
+ if (dma_get_max_seg_size(device->card->device) > SBP2_MAX_SEG_SIZE)
+ BUG_ON(dma_set_max_seg_size(device->card->device,
+ SBP2_MAX_SEG_SIZE));
+
+ shost = scsi_host_alloc(&scsi_driver_template, sizeof(*tgt));
+ if (shost == NULL)
+ return -ENOMEM;
+
+ tgt = (struct sbp2_target *)shost->hostdata;
+ unit->device.driver_data = tgt;
+ tgt->unit = unit;
+ kref_init(&tgt->kref);
+ INIT_LIST_HEAD(&tgt->lu_list);
+ tgt->bus_id = dev_name(&unit->device);
+ tgt->guid = (u64)device->config_rom[3] << 32 | device->config_rom[4];
+
+ if (fw_device_enable_phys_dma(device) < 0)
+ goto fail_shost_put;
+
+ if (scsi_add_host(shost, &unit->device) < 0)
+ goto fail_shost_put;
+
+ fw_device_get(device);
+ fw_unit_get(unit);
+
+ /* implicit directory ID */
+ tgt->directory_id = ((unit->directory - device->config_rom) * 4
+ + CSR_CONFIG_ROM) & 0xffffff;
+
+ firmware_revision = SBP2_ROM_VALUE_MISSING;
+ model = SBP2_ROM_VALUE_MISSING;
+
+ if (sbp2_scan_unit_dir(tgt, unit->directory, &model,
+ &firmware_revision) < 0)
+ goto fail_tgt_put;
- get_device(&unit->device);
+ sbp2_init_workarounds(tgt, model, firmware_revision);
/*
- * We schedule work to do the login so we can easily
- * reschedule retries. Always get the ref before scheduling
- * work.
+ * At S100 we can do 512 bytes per packet, at S200 1024 bytes,
+ * and so on up to 4096 bytes. The SBP-2 max_payload field
+ * specifies the max payload size as 2 ^ (max_payload + 2), so
+ * if we set this to max_speed + 7, we get the right value.
*/
- INIT_DELAYED_WORK(&sd->work, sbp2_login);
- if (schedule_delayed_work(&sd->work, 0))
- kref_get(&sd->kref);
+ tgt->max_payload = min(device->max_speed + 7, 10U);
+ tgt->max_payload = min(tgt->max_payload, device->card->max_receive - 1);
+ /* Do the login in a workqueue so we can easily reschedule retries. */
+ list_for_each_entry(lu, &tgt->lu_list, link)
+ sbp2_queue_work(lu, DIV_ROUND_UP(HZ, 5));
return 0;
- fail_address_handler:
- fw_core_remove_address_handler(&sd->address_handler);
- fail_host:
- scsi_host_put(host);
- fail:
- return err;
+ fail_tgt_put:
+ sbp2_target_put(tgt);
+ return -ENOMEM;
+
+ fail_shost_put:
+ scsi_host_put(shost);
+ return -ENOMEM;
}
static int sbp2_remove(struct device *dev)
{
struct fw_unit *unit = fw_unit(dev);
- struct sbp2_device *sd = unit->device.driver_data;
-
- kref_put(&sd->kref, release_sbp2_device);
+ struct sbp2_target *tgt = unit->device.driver_data;
+ sbp2_target_put(tgt);
return 0;
}
static void sbp2_reconnect(struct work_struct *work)
{
- struct sbp2_device *sd =
- container_of(work, struct sbp2_device, work.work);
- struct fw_unit *unit = sd->unit;
- struct fw_device *device = fw_device(unit->device.parent);
+ struct sbp2_logical_unit *lu =
+ container_of(work, struct sbp2_logical_unit, work.work);
+ struct sbp2_target *tgt = lu->tgt;
+ struct fw_device *device = fw_device(tgt->unit->device.parent);
int generation, node_id, local_node_id;
- generation = device->card->generation;
- node_id = device->node->node_id;
- local_node_id = device->card->local_node->node_id;
+ if (fw_device_is_shutdown(device))
+ goto out;
+
+ generation = device->generation;
+ smp_rmb(); /* node IDs must not be older than generation */
+ node_id = device->node_id;
+ local_node_id = device->card->node_id;
- if (sbp2_send_management_orb(unit, node_id, generation,
+ if (sbp2_send_management_orb(lu, node_id, generation,
SBP2_RECONNECT_REQUEST,
- sd->login_id, NULL) < 0) {
- if (sd->retries++ >= 5) {
- fw_error("failed to reconnect to %s\n",
- unit->device.bus_id);
- /* Fall back and try to log in again. */
- sd->retries = 0;
- PREPARE_DELAYED_WORK(&sd->work, sbp2_login);
+ lu->login_id, NULL) < 0) {
+ /*
+ * If reconnect was impossible even though we are in the
+ * current generation, fall back and try to log in again.
+ *
+ * We could check for "Function rejected" status, but
+ * looking at the bus generation as simpler and more general.
+ */
+ smp_rmb(); /* get current card generation */
+ if (generation == device->card->generation ||
+ lu->retries++ >= 5) {
+ fw_error("%s: failed to reconnect\n", tgt->bus_id);
+ lu->retries = 0;
+ PREPARE_DELAYED_WORK(&lu->work, sbp2_login);
}
- schedule_delayed_work(&sd->work, DIV_ROUND_UP(HZ, 5));
- return;
+ sbp2_queue_work(lu, DIV_ROUND_UP(HZ, 5));
+ goto out;
}
- sd->generation = generation;
- sd->node_id = node_id;
- sd->address_high = local_node_id << 16;
+ tgt->node_id = node_id;
+ tgt->address_high = local_node_id << 16;
+ smp_wmb(); /* node IDs must not be older than generation */
+ lu->generation = generation;
+
+ fw_notify("%s: reconnected to LUN %04x (%d retries)\n",
+ tgt->bus_id, lu->lun, lu->retries);
- fw_notify("reconnected to unit %s (%d retries)\n",
- unit->device.bus_id, sd->retries);
- sbp2_agent_reset(unit);
- sbp2_cancel_orbs(unit);
- kref_put(&sd->kref, release_sbp2_device);
+ sbp2_agent_reset(lu);
+ sbp2_cancel_orbs(lu);
+ sbp2_conditionally_unblock(lu);
+ out:
+ sbp2_target_put(tgt);
}
static void sbp2_update(struct fw_unit *unit)
{
- struct fw_device *device = fw_device(unit->device.parent);
- struct sbp2_device *sd = unit->device.driver_data;
+ struct sbp2_target *tgt = unit->device.driver_data;
+ struct sbp2_logical_unit *lu;
+
+ fw_device_enable_phys_dma(fw_device(unit->device.parent));
- sd->retries = 0;
- fw_device_enable_phys_dma(device);
- if (schedule_delayed_work(&sd->work, 0))
- kref_get(&sd->kref);
+ /*
+ * Fw-core serializes sbp2_update() against sbp2_remove().
+ * Iteration over tgt->lu_list is therefore safe here.
+ */
+ list_for_each_entry(lu, &tgt->lu_list, link) {
+ sbp2_conditionally_block(lu);
+ lu->retries = 0;
+ sbp2_queue_work(lu, 0);
+ }
}
#define SBP2_UNIT_SPEC_ID_ENTRY 0x0000609e
.id_table = sbp2_id_table,
};
-static unsigned int
-sbp2_status_to_sense_data(u8 *sbp2_status, u8 *sense_data)
+static void sbp2_unmap_scatterlist(struct device *card_device,
+ struct sbp2_command_orb *orb)
+{
+ if (scsi_sg_count(orb->cmd))
+ dma_unmap_sg(card_device, scsi_sglist(orb->cmd),
+ scsi_sg_count(orb->cmd),
+ orb->cmd->sc_data_direction);
+
+ if (orb->request.misc & cpu_to_be32(COMMAND_ORB_PAGE_TABLE_PRESENT))
+ dma_unmap_single(card_device, orb->page_table_bus,
+ sizeof(orb->page_table), DMA_TO_DEVICE);
+}
+
+static unsigned int sbp2_status_to_sense_data(u8 *sbp2_status, u8 *sense_data)
{
int sam_status;
}
}
-static void
-complete_command_orb(struct sbp2_orb *base_orb, struct sbp2_status *status)
+static void complete_command_orb(struct sbp2_orb *base_orb,
+ struct sbp2_status *status)
{
struct sbp2_command_orb *orb =
container_of(base_orb, struct sbp2_command_orb, base);
- struct fw_unit *unit = orb->unit;
- struct fw_device *device = fw_device(unit->device.parent);
- struct scatterlist *sg;
+ struct fw_device *device = fw_device(orb->lu->tgt->unit->device.parent);
int result;
if (status != NULL) {
if (STATUS_GET_DEAD(*status))
- sbp2_agent_reset(unit);
+ sbp2_agent_reset_no_wait(orb->lu);
switch (STATUS_GET_RESPONSE(*status)) {
case SBP2_STATUS_REQUEST_COMPLETE:
* or when sending the write (less likely).
*/
result = DID_BUS_BUSY << 16;
+ sbp2_conditionally_block(orb->lu);
}
dma_unmap_single(device->card->device, orb->base.request_bus,
sizeof(orb->request), DMA_TO_DEVICE);
-
- if (orb->cmd->use_sg > 0) {
- sg = (struct scatterlist *)orb->cmd->request_buffer;
- dma_unmap_sg(device->card->device, sg, orb->cmd->use_sg,
- orb->cmd->sc_data_direction);
- }
-
- if (orb->page_table_bus != 0)
- dma_unmap_single(device->card->device, orb->page_table_bus,
- sizeof(orb->page_table_bus), DMA_TO_DEVICE);
+ sbp2_unmap_scatterlist(device->card->device, orb);
orb->cmd->result = result;
orb->done(orb->cmd);
- kfree(orb);
}
-static int sbp2_command_orb_map_scatterlist(struct sbp2_command_orb *orb)
+static int sbp2_map_scatterlist(struct sbp2_command_orb *orb,
+ struct fw_device *device, struct sbp2_logical_unit *lu)
{
- struct sbp2_device *sd =
- (struct sbp2_device *)orb->cmd->device->host->hostdata;
- struct fw_unit *unit = sd->unit;
- struct fw_device *device = fw_device(unit->device.parent);
- struct scatterlist *sg;
- int sg_len, l, i, j, count;
- size_t size;
- dma_addr_t sg_addr;
-
- sg = (struct scatterlist *)orb->cmd->request_buffer;
- count = dma_map_sg(device->card->device, sg, orb->cmd->use_sg,
- orb->cmd->sc_data_direction);
- if (count == 0)
+ struct scatterlist *sg = scsi_sglist(orb->cmd);
+ int i, n;
+
+ n = dma_map_sg(device->card->device, sg, scsi_sg_count(orb->cmd),
+ orb->cmd->sc_data_direction);
+ if (n == 0)
goto fail;
/*
* as the second generation iPod which doesn't support page
* tables.
*/
- if (count == 1 && sg_dma_len(sg) < SBP2_MAX_SG_ELEMENT_LENGTH) {
- orb->request.data_descriptor.high = sd->address_high;
- orb->request.data_descriptor.low = sg_dma_address(sg);
+ if (n == 1) {
+ orb->request.data_descriptor.high =
+ cpu_to_be32(lu->tgt->address_high);
+ orb->request.data_descriptor.low =
+ cpu_to_be32(sg_dma_address(sg));
orb->request.misc |=
- COMMAND_ORB_DATA_SIZE(sg_dma_len(sg));
+ cpu_to_be32(COMMAND_ORB_DATA_SIZE(sg_dma_len(sg)));
return 0;
}
- /*
- * Convert the scatterlist to an sbp2 page table. If any
- * scatterlist entries are too big for sbp2, we split them as we
- * go. Even if we ask the block I/O layer to not give us sg
- * elements larger than 65535 bytes, some IOMMUs may merge sg elements
- * during DMA mapping, and Linux currently doesn't prevent this.
- */
- for (i = 0, j = 0; i < count; i++) {
- sg_len = sg_dma_len(sg + i);
- sg_addr = sg_dma_address(sg + i);
- while (sg_len) {
- /* FIXME: This won't get us out of the pinch. */
- if (unlikely(j >= ARRAY_SIZE(orb->page_table))) {
- fw_error("page table overflow\n");
- goto fail_page_table;
- }
- l = min(sg_len, SBP2_MAX_SG_ELEMENT_LENGTH);
- orb->page_table[j].low = sg_addr;
- orb->page_table[j].high = (l << 16);
- sg_addr += l;
- sg_len -= l;
- j++;
- }
+ for_each_sg(sg, sg, n, i) {
+ orb->page_table[i].high = cpu_to_be32(sg_dma_len(sg) << 16);
+ orb->page_table[i].low = cpu_to_be32(sg_dma_address(sg));
}
- size = sizeof(orb->page_table[0]) * j;
+ orb->page_table_bus =
+ dma_map_single(device->card->device, orb->page_table,
+ sizeof(orb->page_table), DMA_TO_DEVICE);
+ if (dma_mapping_error(device->card->device, orb->page_table_bus))
+ goto fail_page_table;
/*
* The data_descriptor pointer is the one case where we need
* initiator (i.e. us), but data_descriptor can refer to data
* on other nodes so we need to put our ID in descriptor.high.
*/
-
- orb->page_table_bus =
- dma_map_single(device->card->device, orb->page_table,
- size, DMA_TO_DEVICE);
- if (dma_mapping_error(orb->page_table_bus))
- goto fail_page_table;
- orb->request.data_descriptor.high = sd->address_high;
- orb->request.data_descriptor.low = orb->page_table_bus;
- orb->request.misc |=
- COMMAND_ORB_PAGE_TABLE_PRESENT |
- COMMAND_ORB_DATA_SIZE(j);
-
- fw_memcpy_to_be32(orb->page_table, orb->page_table, size);
+ orb->request.data_descriptor.high = cpu_to_be32(lu->tgt->address_high);
+ orb->request.data_descriptor.low = cpu_to_be32(orb->page_table_bus);
+ orb->request.misc |= cpu_to_be32(COMMAND_ORB_PAGE_TABLE_PRESENT |
+ COMMAND_ORB_DATA_SIZE(n));
return 0;
fail_page_table:
- dma_unmap_sg(device->card->device, sg, orb->cmd->use_sg,
- orb->cmd->sc_data_direction);
+ dma_unmap_sg(device->card->device, scsi_sglist(orb->cmd),
+ scsi_sg_count(orb->cmd), orb->cmd->sc_data_direction);
fail:
return -ENOMEM;
}
static int sbp2_scsi_queuecommand(struct scsi_cmnd *cmd, scsi_done_fn_t done)
{
- struct sbp2_device *sd =
- (struct sbp2_device *)cmd->device->host->hostdata;
- struct fw_unit *unit = sd->unit;
- struct fw_device *device = fw_device(unit->device.parent);
+ struct sbp2_logical_unit *lu = cmd->device->hostdata;
+ struct fw_device *device = fw_device(lu->tgt->unit->device.parent);
struct sbp2_command_orb *orb;
+ int generation, retval = SCSI_MLQUEUE_HOST_BUSY;
/*
* Bidirectional commands are not yet implemented, and unknown
orb = kzalloc(sizeof(*orb), GFP_ATOMIC);
if (orb == NULL) {
fw_notify("failed to alloc orb\n");
- goto fail_alloc;
+ return SCSI_MLQUEUE_HOST_BUSY;
}
/* Initialize rcode to something not RCODE_COMPLETE. */
orb->base.rcode = -1;
- orb->base.request_bus =
- dma_map_single(device->card->device, &orb->request,
- sizeof(orb->request), DMA_TO_DEVICE);
- if (dma_mapping_error(orb->base.request_bus))
- goto fail_mapping;
+ kref_init(&orb->base.kref);
- orb->unit = unit;
+ orb->lu = lu;
orb->done = done;
orb->cmd = cmd;
- orb->request.next.high = SBP2_ORB_NULL;
- orb->request.next.low = 0x0;
- /*
- * At speed 100 we can do 512 bytes per packet, at speed 200,
- * 1024 bytes per packet etc. The SBP-2 max_payload field
- * specifies the max payload size as 2 ^ (max_payload + 2), so
- * if we set this to max_speed + 7, we get the right value.
- */
- orb->request.misc =
- COMMAND_ORB_MAX_PAYLOAD(device->max_speed + 7) |
+ orb->request.next.high = cpu_to_be32(SBP2_ORB_NULL);
+ orb->request.misc = cpu_to_be32(
+ COMMAND_ORB_MAX_PAYLOAD(lu->tgt->max_payload) |
COMMAND_ORB_SPEED(device->max_speed) |
- COMMAND_ORB_NOTIFY;
+ COMMAND_ORB_NOTIFY);
if (cmd->sc_data_direction == DMA_FROM_DEVICE)
- orb->request.misc |=
- COMMAND_ORB_DIRECTION(SBP2_DIRECTION_FROM_MEDIA);
- else if (cmd->sc_data_direction == DMA_TO_DEVICE)
- orb->request.misc |=
- COMMAND_ORB_DIRECTION(SBP2_DIRECTION_TO_MEDIA);
+ orb->request.misc |= cpu_to_be32(COMMAND_ORB_DIRECTION);
- if (cmd->use_sg && sbp2_command_orb_map_scatterlist(orb) < 0)
- goto fail_map_payload;
+ generation = device->generation;
+ smp_rmb(); /* sbp2_map_scatterlist looks at tgt->address_high */
- fw_memcpy_to_be32(&orb->request, &orb->request, sizeof(orb->request));
+ if (scsi_sg_count(cmd) && sbp2_map_scatterlist(orb, device, lu) < 0)
+ goto out;
- memset(orb->request.command_block,
- 0, sizeof(orb->request.command_block));
- memcpy(orb->request.command_block, cmd->cmnd, COMMAND_SIZE(*cmd->cmnd));
+ memcpy(orb->request.command_block, cmd->cmnd, cmd->cmd_len);
orb->base.callback = complete_command_orb;
+ orb->base.request_bus =
+ dma_map_single(device->card->device, &orb->request,
+ sizeof(orb->request), DMA_TO_DEVICE);
+ if (dma_mapping_error(device->card->device, orb->base.request_bus)) {
+ sbp2_unmap_scatterlist(device->card->device, orb);
+ goto out;
+ }
- sbp2_send_orb(&orb->base, unit, sd->node_id, sd->generation,
- sd->command_block_agent_address + SBP2_ORB_POINTER);
-
- return 0;
-
- fail_map_payload:
- dma_unmap_single(device->card->device, orb->base.request_bus,
- sizeof(orb->request), DMA_TO_DEVICE);
- fail_mapping:
- kfree(orb);
- fail_alloc:
- return SCSI_MLQUEUE_HOST_BUSY;
+ sbp2_send_orb(&orb->base, lu, lu->tgt->node_id, generation,
+ lu->command_block_agent_address + SBP2_ORB_POINTER);
+ retval = 0;
+ out:
+ kref_put(&orb->base.kref, free_orb);
+ return retval;
}
static int sbp2_scsi_slave_alloc(struct scsi_device *sdev)
{
- struct sbp2_device *sd = (struct sbp2_device *)sdev->host->hostdata;
+ struct sbp2_logical_unit *lu = sdev->hostdata;
+
+ /* (Re-)Adding logical units via the SCSI stack is not supported. */
+ if (!lu)
+ return -ENOSYS;
sdev->allow_restart = 1;
- if (sd->workarounds & SBP2_WORKAROUND_INQUIRY_36)
+ /* SBP-2 requires quadlet alignment of the data buffers. */
+ blk_queue_update_dma_alignment(sdev->request_queue, 4 - 1);
+
+ if (lu->tgt->workarounds & SBP2_WORKAROUND_INQUIRY_36)
sdev->inquiry_len = 36;
+
return 0;
}
static int sbp2_scsi_slave_configure(struct scsi_device *sdev)
{
- struct sbp2_device *sd = (struct sbp2_device *)sdev->host->hostdata;
- struct fw_unit *unit = sd->unit;
+ struct sbp2_logical_unit *lu = sdev->hostdata;
sdev->use_10_for_rw = 1;
+ if (sbp2_param_exclusive_login)
+ sdev->manage_start_stop = 1;
+
if (sdev->type == TYPE_ROM)
sdev->use_10_for_ms = 1;
+
if (sdev->type == TYPE_DISK &&
- sd->workarounds & SBP2_WORKAROUND_MODE_SENSE_8)
+ lu->tgt->workarounds & SBP2_WORKAROUND_MODE_SENSE_8)
sdev->skip_ms_page_8 = 1;
- if (sd->workarounds & SBP2_WORKAROUND_FIX_CAPACITY) {
- fw_notify("setting fix_capacity for %s\n", unit->device.bus_id);
+
+ if (lu->tgt->workarounds & SBP2_WORKAROUND_FIX_CAPACITY)
sdev->fix_capacity = 1;
- }
- if (sd->workarounds & SBP2_WORKAROUND_128K_MAX_TRANS)
+
+ if (lu->tgt->workarounds & SBP2_WORKAROUND_POWER_CONDITION)
+ sdev->start_stop_pwr_cond = 1;
+
+ if (lu->tgt->workarounds & SBP2_WORKAROUND_128K_MAX_TRANS)
blk_queue_max_sectors(sdev->request_queue, 128 * 1024 / 512);
+
+ blk_queue_max_segment_size(sdev->request_queue, SBP2_MAX_SEG_SIZE);
+
return 0;
}
*/
static int sbp2_scsi_abort(struct scsi_cmnd *cmd)
{
- struct sbp2_device *sd =
- (struct sbp2_device *)cmd->device->host->hostdata;
- struct fw_unit *unit = sd->unit;
+ struct sbp2_logical_unit *lu = cmd->device->hostdata;
- fw_notify("sbp2_scsi_abort\n");
- sbp2_agent_reset(unit);
- sbp2_cancel_orbs(unit);
+ fw_notify("%s: sbp2_scsi_abort\n", lu->tgt->bus_id);
+ sbp2_agent_reset(lu);
+ sbp2_cancel_orbs(lu);
return SUCCESS;
}
* This is the concatenation of target port identifier and logical unit
* identifier as per SAM-2...SAM-4 annex A.
*/
-static ssize_t
-sbp2_sysfs_ieee1394_id_show(struct device *dev, struct device_attribute *attr,
- char *buf)
+static ssize_t sbp2_sysfs_ieee1394_id_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
{
struct scsi_device *sdev = to_scsi_device(dev);
- struct sbp2_device *sd;
- struct fw_unit *unit;
- struct fw_device *device;
- u32 directory_id;
- struct fw_csr_iterator ci;
- int key, value, lun;
+ struct sbp2_logical_unit *lu;
if (!sdev)
return 0;
- sd = (struct sbp2_device *)sdev->host->hostdata;
- unit = sd->unit;
- device = fw_device(unit->device.parent);
- /* implicit directory ID */
- directory_id = ((unit->directory - device->config_rom) * 4
- + CSR_CONFIG_ROM) & 0xffffff;
+ lu = sdev->hostdata;
- /* explicit directory ID, overrides implicit ID if present */
- fw_csr_iterator_init(&ci, unit->directory);
- while (fw_csr_iterator_next(&ci, &key, &value))
- if (key == CSR_DIRECTORY_ID) {
- directory_id = value;
- break;
- }
-
- /* FIXME: Make this work for multi-lun devices. */
- lun = 0;
-
- return sprintf(buf, "%08x%08x:%06x:%04x\n",
- device->config_rom[3], device->config_rom[4],
- directory_id, lun);
+ return sprintf(buf, "%016llx:%06x:%04x\n",
+ (unsigned long long)lu->tgt->guid,
+ lu->tgt->directory_id, lu->lun);
}
static DEVICE_ATTR(ieee1394_id, S_IRUGO, sbp2_sysfs_ieee1394_id_show, NULL);
static struct scsi_host_template scsi_driver_template = {
.module = THIS_MODULE,
.name = "SBP-2 IEEE-1394",
- .proc_name = (char *)sbp2_driver_name,
+ .proc_name = sbp2_driver_name,
.queuecommand = sbp2_scsi_queuecommand,
.slave_alloc = sbp2_scsi_slave_alloc,
.slave_configure = sbp2_scsi_slave_configure,
static int __init sbp2_init(void)
{
+ sbp2_wq = create_singlethread_workqueue(KBUILD_MODNAME);
+ if (!sbp2_wq)
+ return -ENOMEM;
+
return driver_register(&sbp2_driver.driver);
}
static void __exit sbp2_cleanup(void)
{
driver_unregister(&sbp2_driver.driver);
+ destroy_workqueue(sbp2_wq);
}
module_init(sbp2_init);