-# -*- shell-script -*-
+menu "IEEE 1394 (FireWire) support"
+ depends on PCI || BROKEN
+ # firewire-core does not depend on PCI but is
+ # not useful without PCI controller driver
-comment "An alternative FireWire stack is available with EXPERIMENTAL=y"
- depends on EXPERIMENTAL=n
+comment "You can enable one or both FireWire driver stacks."
+comment "The newer stack is recommended."
config FIREWIRE
- tristate "IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL"
- depends on EXPERIMENTAL
+ tristate "FireWire driver stack"
select CRC_ITU_T
help
- This is the "Juju" FireWire stack, a new alternative implementation
- designed for robustness and simplicity. You can build either this
- stack, or the classic stack (the ieee1394 driver, ohci1394 etc.)
- or both. Please read http://wiki.linux1394.org/JujuMigration before
- you enable the new stack.
+ This is the new-generation IEEE 1394 (FireWire) driver stack
+ a.k.a. Juju, a new implementation designed for robustness and
+ simplicity.
+ See http://ieee1394.wiki.kernel.org/index.php/Juju_Migration
+ for information about migration from the older Linux 1394 stack
+ to the new driver stack.
To compile this driver as a module, say M here: the module will be
- called firewire-core. It functionally replaces ieee1394, raw1394,
- and video1394.
-
- NOTE:
-
- You should only build ONE of the stacks, unless you REALLY know what
- you are doing. If you install both, you should configure them only as
- modules rather than link them statically, and you should blacklist one
- of the concurrent low-level drivers in /etc/modprobe.conf. Add either
-
- blacklist firewire-ohci
- or
- blacklist ohci1394
-
- there depending on which driver you DON'T want to have auto-loaded.
- You can optionally do the same with the other IEEE 1394/ FireWire
- drivers.
-
- If you have an old modprobe which doesn't implement the blacklist
- directive, use either
-
- install firewire-ohci /bin/true
- or
- install ohci1394 /bin/true
-
- and so on, depending on which modules you DON't want to have
- auto-loaded.
+ called firewire-core.
config FIREWIRE_OHCI
- tristate "Support for OHCI FireWire host controllers"
+ tristate "OHCI-1394 controllers"
depends on PCI && FIREWIRE
help
Enable this driver if you have a FireWire controller based
is the only chipset in use, so say Y here.
To compile this driver as a module, say M here: The module will be
- called firewire-ohci. It replaces ohci1394 of the classic IEEE 1394
- stack.
-
- NOTE:
+ called firewire-ohci.
- If you also build ohci1394 of the classic stack, blacklist either
- ohci1394 or firewire-ohci to let hotplug load only the desired driver.
+config FIREWIRE_OHCI_DEBUG
+ bool
+ depends on FIREWIRE_OHCI
+ default y
config FIREWIRE_SBP2
- tristate "Support for storage devices (SBP-2 protocol driver)"
+ tristate "Storage devices (SBP-2 protocol)"
depends on FIREWIRE && SCSI
help
This option enables you to use SBP-2 devices connected to a
like scanners.
To compile this driver as a module, say M here: The module will be
- called firewire-sbp2. It replaces sbp2 of the classic IEEE 1394
- stack.
+ called firewire-sbp2.
You should also enable support for disks, CD-ROMs, etc. in the SCSI
configuration section.
- NOTE:
+config FIREWIRE_NET
+ tristate "IP networking over 1394 (EXPERIMENTAL)"
+ depends on FIREWIRE && INET && EXPERIMENTAL
+ help
+ This enables IPv4 over IEEE 1394, providing IP connectivity with
+ other implementations of RFC 2734 as found on several operating
+ systems. Multicast support is currently limited.
+
+ NOTE, this driver is not stable yet!
+
+ To compile this driver as a module, say M here: The module will be
+ called firewire-net.
- If you also build sbp2 of the classic stack, blacklist either sbp2
- or firewire-sbp2 to let hotplug load only the desired driver.
+source "drivers/ieee1394/Kconfig"
+endmenu