/*
* Berkshire PCI-PC Watchdog Card Driver
*
- * (c) Copyright 2003 Wim Van Sebroeck <wim@iguana.be>.
+ * (c) Copyright 2003-2005 Wim Van Sebroeck <wim@iguana.be>.
*
* Based on source code of the following authors:
* Ken Hollis <kenji@bitgate.com>,
*/
/*
- * A bells and whistles driver is available from http://www.pcwd.de/
+ * A bells and whistles driver is available from:
+ * http://www.kernel.org/pub/linux/kernel/people/wim/pcwd/pcwd_pci/
+ *
* More info available at http://www.berkprod.com/ or http://www.pcwatchdog.com/
*/
#include <asm/io.h> /* For inb/outb/... */
/* Module and version information */
-#define WATCHDOG_VERSION "1.01"
-#define WATCHDOG_DATE "02 Sep 2005"
+#define WATCHDOG_VERSION "1.02"
+#define WATCHDOG_DATE "03 Sep 2005"
#define WATCHDOG_DRIVER_NAME "PCI-PC Watchdog"
#define WATCHDOG_NAME "pcwd_pci"
#define PFX WATCHDOG_NAME ": "
* These are the defines that describe the control status bits for the
* PCI-PC Watchdog card.
*/
-#define WD_PCI_WTRP 0x01 /* Watchdog Trip status */
-#define WD_PCI_HRBT 0x02 /* Watchdog Heartbeat */
-#define WD_PCI_TTRP 0x04 /* Temperature Trip status */
+/* Port 1 : Control Status #1 */
+#define WD_PCI_WTRP 0x01 /* Watchdog Trip status */
+#define WD_PCI_HRBT 0x02 /* Watchdog Heartbeat */
+#define WD_PCI_TTRP 0x04 /* Temperature Trip status */
+#define WD_PCI_RL2A 0x08 /* Relay 2 Active */
+#define WD_PCI_RL1A 0x10 /* Relay 1 Active */
+#define WD_PCI_R2DS 0x40 /* Relay 2 Disable Temperature-trip/reset */
+#define WD_PCI_RLY2 0x80 /* Activate Relay 2 on the board */
+/* Port 2 : Control Status #2 */
+#define WD_PCI_WDIS 0x10 /* Watchdog Disable */
+#define WD_PCI_ENTP 0x20 /* Enable Temperature Trip Reset */
+#define WD_PCI_WRSP 0x40 /* Watchdog wrote response */
+#define WD_PCI_PCMD 0x80 /* PC has sent command */
/* according to documentation max. time to process a command for the pci
* watchdog card is 100 ms, so we give it 150 ms to do it's job */
#define PCI_COMMAND_TIMEOUT 150
/* Watchdog's internal commands */
-#define CMD_GET_STATUS 0x04
-#define CMD_GET_FIRMWARE_VERSION 0x08
-#define CMD_READ_WATCHDOG_TIMEOUT 0x18
-#define CMD_WRITE_WATCHDOG_TIMEOUT 0x19
+#define CMD_GET_STATUS 0x04
+#define CMD_GET_FIRMWARE_VERSION 0x08
+#define CMD_READ_WATCHDOG_TIMEOUT 0x18
+#define CMD_WRITE_WATCHDOG_TIMEOUT 0x19
+#define CMD_GET_CLEAR_RESET_COUNT 0x84
/* We can only use 1 card due to the /dev/watchdog restriction */
static int cards_found;
static int temp_panic;
static unsigned long is_active;
static char expect_release;
-static struct {
- int supports_temp; /* Wether or not the card has a temperature device */
- int boot_status; /* The card's boot status */
- unsigned long io_addr; /* The cards I/O address */
- spinlock_t io_lock;
- struct pci_dev *pdev;
+static struct { /* this is private data for each PCI-PC watchdog card */
+ int supports_temp; /* Wether or not the card has a temperature device */
+ int boot_status; /* The card's boot status */
+ unsigned long io_addr; /* The cards I/O address */
+ spinlock_t io_lock; /* the lock for io operations */
+ struct pci_dev *pdev; /* the PCI-device */
} pcipcwd_private;
/* module parameters */
+#define QUIET 0 /* Default */
+#define VERBOSE 1 /* Verbose */
+#define DEBUG 2 /* print fancy stuff too */
+static int debug = QUIET;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level: 0=Quiet, 1=Verbose, 2=Debug (default=0)");
+
#define WATCHDOG_HEARTBEAT 2 /* 2 sec default heartbeat */
static int heartbeat = WATCHDOG_HEARTBEAT;
module_param(heartbeat, int, 0);
{
int got_response, count;
+ if (debug >= DEBUG)
+ printk(KERN_DEBUG PFX "sending following data cmd=0x%02x msb=0x%02x lsb=0x%02x\n",
+ cmd, *msb, *lsb);
+
spin_lock(&pcipcwd_private.io_lock);
/* If a command requires data it should be written first.
* Data for commands with 8 bits of data should be written to port 4.
/* wait till the pci card processed the command, signaled by
* the WRSP bit in port 2 and give it a max. timeout of
* PCI_COMMAND_TIMEOUT to process */
- got_response = inb_p(pcipcwd_private.io_addr + 2) & 0x40;
+ got_response = inb_p(pcipcwd_private.io_addr + 2) & WD_PCI_WRSP;
for (count = 0; (count < PCI_COMMAND_TIMEOUT) && (!got_response); count++) {
mdelay(1);
- got_response = inb_p(pcipcwd_private.io_addr + 2) & 0x40;
+ got_response = inb_p(pcipcwd_private.io_addr + 2) & WD_PCI_WRSP;
+ }
+
+ if (debug >= DEBUG) {
+ if (got_response) {
+ printk(KERN_DEBUG PFX "time to process command was: %d ms\n",
+ count);
+ } else {
+ printk(KERN_DEBUG PFX "card did not respond on command!\n");
+ }
}
if (got_response) {
/* clear WRSP bit */
inb_p(pcipcwd_private.io_addr + 6);
+
+ if (debug >= DEBUG)
+ printk(KERN_DEBUG PFX "received following data for cmd=0x%02x: msb=0x%02x lsb=0x%02x\n",
+ cmd, *msb, *lsb);
}
+
spin_unlock(&pcipcwd_private.io_lock);
return got_response;
}
+static inline void pcipcwd_check_temperature_support(void)
+{
+ if (inb_p(pcipcwd_private.io_addr) != 0xF0)
+ pcipcwd_private.supports_temp = 1;
+}
+
+static int pcipcwd_get_option_switches(void)
+{
+ int option_switches;
+
+ option_switches = inb_p(pcipcwd_private.io_addr + 3);
+ return option_switches;
+}
+
+static void pcipcwd_show_card_info(void)
+{
+ int got_fw_rev, fw_rev_major, fw_rev_minor;
+ char fw_ver_str[20]; /* The cards firmware version */
+ int option_switches;
+
+ got_fw_rev = send_command(CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor);
+ if (got_fw_rev) {
+ sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor);
+ } else {
+ sprintf(fw_ver_str, "<card no answer>");
+ }
+
+ /* Get switch settings */
+ option_switches = pcipcwd_get_option_switches();
+
+ printk(KERN_INFO PFX "Found card at port 0x%04x (Firmware: %s) %s temp option\n",
+ (int) pcipcwd_private.io_addr, fw_ver_str,
+ (pcipcwd_private.supports_temp ? "with" : "without"));
+
+ printk(KERN_INFO PFX "Option switches (0x%02x): Temperature Reset Enable=%s, Power On Delay=%s\n",
+ option_switches,
+ ((option_switches & 0x10) ? "ON" : "OFF"),
+ ((option_switches & 0x08) ? "ON" : "OFF"));
+
+ if (pcipcwd_private.boot_status & WDIOF_CARDRESET)
+ printk(KERN_INFO PFX "Previous reset was caused by the Watchdog card\n");
+
+ if (pcipcwd_private.boot_status & WDIOF_OVERHEAT)
+ printk(KERN_INFO PFX "Card sensed a CPU Overheat\n");
+
+ if (pcipcwd_private.boot_status == 0)
+ printk(KERN_INFO PFX "No previous trip detected - Cold boot or reset\n");
+}
+
static int pcipcwd_start(void)
{
int stat_reg;
stat_reg = inb_p(pcipcwd_private.io_addr + 2);
spin_unlock(&pcipcwd_private.io_lock);
- if (stat_reg & 0x10) {
+ if (stat_reg & WD_PCI_WDIS) {
printk(KERN_ERR PFX "Card timer not enabled\n");
return -1;
}
+ if (debug >= VERBOSE)
+ printk(KERN_DEBUG PFX "Watchdog started\n");
+
return 0;
}
stat_reg = inb_p(pcipcwd_private.io_addr + 2);
spin_unlock(&pcipcwd_private.io_lock);
- if (!(stat_reg & 0x10)) {
+ if (!(stat_reg & WD_PCI_WDIS)) {
printk(KERN_ERR PFX "Card did not acknowledge disable attempt\n");
return -1;
}
+ if (debug >= VERBOSE)
+ printk(KERN_DEBUG PFX "Watchdog stopped\n");
+
return 0;
}
static int pcipcwd_keepalive(void)
{
/* Re-trigger watchdog by writing to port 0 */
- outb_p(0x42, pcipcwd_private.io_addr);
+ outb_p(0x42, pcipcwd_private.io_addr); /* send out any data */
+
+ if (debug >= DEBUG)
+ printk(KERN_DEBUG PFX "Watchdog keepalive signal send\n");
+
return 0;
}
send_command(CMD_WRITE_WATCHDOG_TIMEOUT, &t_msb, &t_lsb);
heartbeat = t;
+ if (debug >= VERBOSE)
+ printk(KERN_DEBUG PFX "New heartbeat: %d\n",
+ heartbeat);
+
return 0;
}
static int pcipcwd_get_status(int *status)
{
- int new_status;
+ int control_status;
*status=0;
- new_status = inb_p(pcipcwd_private.io_addr + 1);
- if (new_status & WD_PCI_WTRP)
+ control_status = inb_p(pcipcwd_private.io_addr + 1);
+ if (control_status & WD_PCI_WTRP)
*status |= WDIOF_CARDRESET;
- if (new_status & WD_PCI_TTRP) {
+ if (control_status & WD_PCI_TTRP) {
*status |= WDIOF_OVERHEAT;
if (temp_panic)
panic(PFX "Temperature overheat trip!\n");
}
+ if (debug >= DEBUG)
+ printk(KERN_DEBUG PFX "Control Status #1: 0x%02x\n",
+ control_status);
+
return 0;
}
static int pcipcwd_clear_status(void)
{
- outb_p(0x01, pcipcwd_private.io_addr + 1);
+ int control_status;
+ int msb;
+ int reset_counter;
+
+ if (debug >= VERBOSE)
+ printk(KERN_INFO PFX "clearing watchdog trip status & LED\n");
+
+ control_status = inb_p(pcipcwd_private.io_addr + 1);
+
+ if (debug >= DEBUG) {
+ printk(KERN_DEBUG PFX "status was: 0x%02x\n", control_status);
+ printk(KERN_DEBUG PFX "sending: 0x%02x\n",
+ (control_status & WD_PCI_R2DS) | WD_PCI_WTRP);
+ }
+
+ /* clear trip status & LED and keep mode of relay 2 */
+ outb_p((control_status & WD_PCI_R2DS) | WD_PCI_WTRP, pcipcwd_private.io_addr + 1);
+
+ /* clear reset counter */
+ msb=0;
+ reset_counter=0xff;
+ send_command(CMD_GET_CLEAR_RESET_COUNT, &msb, &reset_counter);
+
+ if (debug >= DEBUG) {
+ printk(KERN_DEBUG PFX "reset count was: 0x%02x\n",
+ reset_counter);
+ }
+
return 0;
}
if (!pcipcwd_private.supports_temp)
return -ENODEV;
+ *temperature = inb_p(pcipcwd_private.io_addr);
+
/*
* Convert celsius to fahrenheit, since this was
* the decided 'standard' for this return value.
*/
- *temperature = ((inb_p(pcipcwd_private.io_addr)) * 9 / 5) + 32;
+ *temperature = (*temperature * 9 / 5) + 32;
+
+ if (debug >= DEBUG) {
+ printk(KERN_DEBUG PFX "temperature is: %d F\n",
+ *temperature);
+ }
return 0;
}
*/
static ssize_t pcipcwd_write(struct file *file, const char __user *data,
- size_t len, loff_t *ppos)
+ size_t len, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
if (len) {
static int pcipcwd_open(struct inode *inode, struct file *file)
{
/* /dev/watchdog can only be opened once */
- if (test_and_set_bit(0, &is_active))
+ if (test_and_set_bit(0, &is_active)) {
+ if (debug >= VERBOSE)
+ printk(KERN_ERR PFX "Attempt to open already opened device.\n");
return -EBUSY;
+ }
/* Activate */
pcipcwd_start();
* Init & exit routines
*/
-static inline void check_temperature_support(void)
-{
- if (inb_p(pcipcwd_private.io_addr) != 0xF0)
- pcipcwd_private.supports_temp = 1;
-}
-
static int __devinit pcipcwd_card_init(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
int ret = -EIO;
- int got_fw_rev, fw_rev_major, fw_rev_minor;
- char fw_ver_str[20];
- char option_switches;
cards_found++;
if (cards_found == 1)
pcipcwd_stop();
/* Check whether or not the card supports the temperature device */
- check_temperature_support();
-
- /* Get the Firmware Version */
- got_fw_rev = send_command(CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor);
- if (got_fw_rev) {
- sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor);
- } else {
- sprintf(fw_ver_str, "<card no answer>");
- }
+ pcipcwd_check_temperature_support();
- /* Get switch settings */
- option_switches = inb_p(pcipcwd_private.io_addr + 3);
-
- printk(KERN_INFO PFX "Found card at port 0x%04x (Firmware: %s) %s temp option\n",
- (int) pcipcwd_private.io_addr, fw_ver_str,
- (pcipcwd_private.supports_temp ? "with" : "without"));
-
- printk(KERN_INFO PFX "Option switches (0x%02x): Temperature Reset Enable=%s, Power On Delay=%s\n",
- option_switches,
- ((option_switches & 0x10) ? "ON" : "OFF"),
- ((option_switches & 0x08) ? "ON" : "OFF"));
-
- if (pcipcwd_private.boot_status & WDIOF_CARDRESET)
- printk(KERN_INFO PFX "Previous reset was caused by the Watchdog card\n");
-
- if (pcipcwd_private.boot_status & WDIOF_OVERHEAT)
- printk(KERN_INFO PFX "Card sensed a CPU Overheat\n");
-
- if (pcipcwd_private.boot_status == 0)
- printk(KERN_INFO PFX "No previous trip detected - Cold boot or reset\n");
+ /* Show info about the card itself */
+ pcipcwd_show_card_info();
/* Check that the heartbeat value is within it's range ; if not reset to the default */
if (pcipcwd_set_heartbeat(heartbeat)) {
MODULE_DEVICE_TABLE(pci, pcipcwd_pci_tbl);
static struct pci_driver pcipcwd_driver = {
+ .owner = THIS_MODULE,
.name = WATCHDOG_NAME,
.id_table = pcipcwd_pci_tbl,
.probe = pcipcwd_card_init,
static int __init pcipcwd_init_module(void)
{
- spin_lock_init (&pcipcwd_private.io_lock);
+ spin_lock_init(&pcipcwd_private.io_lock);
return pci_register_driver(&pcipcwd_driver);
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff