/*
- * $Id: synclink_gt.c,v 4.36 2006/08/28 20:47:14 paulkf Exp $
- *
* Device driver for Microgate SyncLink GT serial adapters.
*
* written by Paul Fulghum for Microgate Corporation
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/mm.h>
+#include <linux/seq_file.h>
#include <linux/slab.h>
+#include <linux/smp_lock.h>
#include <linux/netdevice.h>
#include <linux/vmalloc.h>
#include <linux/init.h>
#include <linux/bitops.h>
#include <linux/workqueue.h>
#include <linux/hdlc.h>
+#include <linux/synclink.h>
#include <asm/system.h>
#include <asm/io.h>
#include <asm/types.h>
#include <asm/uaccess.h>
-#include "linux/synclink.h"
-
#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
#define SYNCLINK_GENERIC_HDLC 1
#else
* module identification
*/
static char *driver_name = "SyncLink GT";
-static char *driver_version = "$Revision: 4.36 $";
static char *tty_driver_name = "synclink_gt";
static char *tty_dev_prefix = "ttySLG";
MODULE_LICENSE("GPL");
.remove = __devexit_p(remove_one),
};
-static int pci_registered;
+static bool pci_registered;
/*
* module configuration and status
static int ttymajor;
static int debug_level;
static int maxframe[MAX_DEVICES];
-static int dosyncppp[MAX_DEVICES];
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
-MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
/*
* tty support and callbacks
*/
-#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
-
static struct tty_driver *serial_driver;
static int open(struct tty_struct *tty, struct file * filp);
static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
static int write(struct tty_struct *tty, const unsigned char *buf, int count);
-static void put_char(struct tty_struct *tty, unsigned char ch);
+static int put_char(struct tty_struct *tty, unsigned char ch);
static void send_xchar(struct tty_struct *tty, char ch);
static void wait_until_sent(struct tty_struct *tty, int timeout);
static int write_room(struct tty_struct *tty);
static void tx_release(struct tty_struct *tty);
static int ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
-static int read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
static int chars_in_buffer(struct tty_struct *tty);
static void throttle(struct tty_struct * tty);
static void unthrottle(struct tty_struct * tty);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
/*
* generic HDLC support and callbacks
*/
struct slgt_desc
{
- unsigned short count;
- unsigned short status;
- unsigned int pbuf; /* physical address of data buffer */
- unsigned int next; /* physical address of next descriptor */
+ __le16 count;
+ __le16 status;
+ __le32 pbuf; /* physical address of data buffer */
+ __le32 next; /* physical address of next descriptor */
/* driver book keeping */
char *buf; /* virtual address of data buffer */
unsigned int pdesc; /* physical address of this descriptor */
dma_addr_t buf_dma_addr;
+ unsigned short buf_count;
};
#define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
#define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b))
#define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b))
#define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
+#define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
#define desc_count(a) (le16_to_cpu((a).count))
#define desc_status(a) (le16_to_cpu((a).status))
#define desc_complete(a) (le16_to_cpu((a).status) & BIT15)
*/
struct slgt_info {
void *if_ptr; /* General purpose pointer (used by SPPP) */
+ struct tty_port port;
struct slgt_info *next_device; /* device list link */
int magic;
- int flags;
char device_name[25];
struct pci_dev *pdev;
/* array of pointers to port contexts on this adapter */
struct slgt_info *port_array[SLGT_MAX_PORTS];
- int count; /* count of opens */
int line; /* tty line instance number */
- unsigned short close_delay;
- unsigned short closing_wait; /* time to wait before closing */
struct mgsl_icount icount;
- struct tty_struct *tty;
int timeout;
int x_char; /* xon/xoff character */
- int blocked_open; /* # of blocked opens */
unsigned int read_status_mask;
unsigned int ignore_status_mask;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-
wait_queue_head_t status_event_wait_q;
wait_queue_head_t event_wait_q;
struct timer_list tx_timer;
struct work_struct task;
u32 pending_bh;
- int bh_requested;
- int bh_running;
+ bool bh_requested;
+ bool bh_running;
int isr_overflow;
- int irq_requested; /* nonzero if IRQ requested */
- int irq_occurred; /* for diagnostics use */
+ bool irq_requested; /* true if IRQ requested */
+ bool irq_occurred; /* for diagnostics use */
/* device configuration */
unsigned char __iomem * reg_addr; /* memory mapped registers address */
u32 phys_reg_addr;
- int reg_addr_requested;
+ bool reg_addr_requested;
MGSL_PARAMS params; /* communications parameters */
u32 idle_mode;
u32 max_frame_size; /* as set by device config */
- unsigned int raw_rx_size;
+ unsigned int rbuf_fill_level;
+ unsigned int rx_pio;
unsigned int if_mode;
+ unsigned int base_clock;
/* device status */
- int rx_enabled;
- int rx_restart;
+ bool rx_enabled;
+ bool rx_restart;
- int tx_enabled;
- int tx_active;
+ bool tx_enabled;
+ bool tx_active;
unsigned char signals; /* serial signal states */
int init_error; /* initialization error */
char flag_buf[MAX_ASYNC_BUFFER_SIZE];
char char_buf[MAX_ASYNC_BUFFER_SIZE];
- BOOLEAN drop_rts_on_tx_done;
+ bool drop_rts_on_tx_done;
struct _input_signal_events input_signal_events;
int dcd_chkcount; /* check counts to prevent */
struct slgt_desc *rbufs;
unsigned int rbuf_current;
unsigned int rbuf_index;
+ unsigned int rbuf_fill_index;
+ unsigned short rbuf_fill_count;
unsigned int tbuf_count;
struct slgt_desc *tbufs;
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
struct net_device *netdev;
static void reset_rbufs(struct slgt_info *info);
static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
static void rdma_reset(struct slgt_info *info);
-static int rx_get_frame(struct slgt_info *info);
-static int rx_get_buf(struct slgt_info *info);
+static bool rx_get_frame(struct slgt_info *info);
+static bool rx_get_buf(struct slgt_info *info);
static void tx_start(struct slgt_info *info);
static void tx_stop(struct slgt_info *info);
static void tx_set_idle(struct slgt_info *info);
static unsigned int free_tbuf_count(struct slgt_info *info);
+static unsigned int tbuf_bytes(struct slgt_info *info);
static void reset_tbufs(struct slgt_info *info);
static void tdma_reset(struct slgt_info *info);
static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
static void isr_rdma(struct slgt_info *info);
static void isr_txeom(struct slgt_info *info, unsigned short status);
static void isr_tdma(struct slgt_info *info);
-static irqreturn_t slgt_interrupt(int irq, void *dev_id);
static int alloc_dma_bufs(struct slgt_info *info);
static void free_dma_bufs(struct slgt_info *info);
static int tiocmget(struct tty_struct *tty, struct file *file);
static int tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
static int get_interface(struct slgt_info *info, int __user *if_mode);
static int set_interface(struct slgt_info *info, int if_mode);
static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
return;
ld = tty_ldisc_ref(tty);
if (ld) {
- if (ld->receive_buf)
- ld->receive_buf(tty, data, flags, count);
+ if (ld->ops->receive_buf)
+ ld->ops->receive_buf(tty, data, flags, count);
tty_ldisc_deref(ld);
}
}
}
tty->driver_data = info;
- info->tty = tty;
+ info->port.tty = tty;
- DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->count));
+ DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
/* If port is closing, signal caller to try again */
- if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
- if (info->flags & ASYNC_CLOSING)
- interruptible_sleep_on(&info->close_wait);
- retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
+ if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
+ if (info->port.flags & ASYNC_CLOSING)
+ interruptible_sleep_on(&info->port.close_wait);
+ retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS);
goto cleanup;
}
- info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
spin_lock_irqsave(&info->netlock, flags);
if (info->netcount) {
spin_unlock_irqrestore(&info->netlock, flags);
goto cleanup;
}
- info->count++;
+ info->port.count++;
spin_unlock_irqrestore(&info->netlock, flags);
- if (info->count == 1) {
+ if (info->port.count == 1) {
/* 1st open on this device, init hardware */
retval = startup(info);
if (retval < 0)
cleanup:
if (retval) {
if (tty->count == 1)
- info->tty = NULL; /* tty layer will release tty struct */
- if(info->count)
- info->count--;
+ info->port.tty = NULL; /* tty layer will release tty struct */
+ if(info->port.count)
+ info->port.count--;
}
DBGINFO(("%s open rc=%d\n", info->device_name, retval));
if (sanity_check(info, tty->name, "close"))
return;
- DBGINFO(("%s close entry, count=%d\n", info->device_name, info->count));
-
- if (!info->count)
- return;
-
- if (tty_hung_up_p(filp))
- goto cleanup;
+ DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
- if ((tty->count == 1) && (info->count != 1)) {
- /*
- * tty->count is 1 and the tty structure will be freed.
- * info->count should be one in this case.
- * if it's not, correct it so that the port is shutdown.
- */
- DBGERR(("%s close: bad refcount; tty->count=1, "
- "info->count=%d\n", info->device_name, info->count));
- info->count = 1;
- }
-
- info->count--;
-
- /* if at least one open remaining, leave hardware active */
- if (info->count)
+ if (tty_port_close_start(&info->port, tty, filp) == 0)
goto cleanup;
- info->flags |= ASYNC_CLOSING;
-
- /* set tty->closing to notify line discipline to
- * only process XON/XOFF characters. Only the N_TTY
- * discipline appears to use this (ppp does not).
- */
- tty->closing = 1;
-
- /* wait for transmit data to clear all layers */
-
- if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
- DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
- tty_wait_until_sent(tty, info->closing_wait);
- }
-
- if (info->flags & ASYNC_INITIALIZED)
+ if (info->port.flags & ASYNC_INITIALIZED)
wait_until_sent(tty, info->timeout);
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
+ flush_buffer(tty);
tty_ldisc_flush(tty);
shutdown(info);
- tty->closing = 0;
- info->tty = NULL;
-
- if (info->blocked_open) {
- if (info->close_delay) {
- msleep_interruptible(jiffies_to_msecs(info->close_delay));
- }
- wake_up_interruptible(&info->open_wait);
- }
-
- info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
-
- wake_up_interruptible(&info->close_wait);
-
+ tty_port_close_end(&info->port, tty);
+ info->port.tty = NULL;
cleanup:
- DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->count));
+ DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
}
static void hangup(struct tty_struct *tty)
flush_buffer(tty);
shutdown(info);
- info->count = 0;
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
- info->tty = NULL;
+ info->port.count = 0;
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ info->port.tty = NULL;
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
}
static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
DBGINFO(("%s set_termios\n", tty->driver->name));
- /* just return if nothing has changed */
- if ((tty->termios->c_cflag == old_termios->c_cflag)
- && (RELEVANT_IFLAG(tty->termios->c_iflag)
- == RELEVANT_IFLAG(old_termios->c_iflag)))
- return;
-
change_params(info);
/* Handle transition to B0 status */
}
}
+static void update_tx_timer(struct slgt_info *info)
+{
+ /*
+ * use worst case speed of 1200bps to calculate transmit timeout
+ * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
+ */
+ if (info->params.mode == MGSL_MODE_HDLC) {
+ int timeout = (tbuf_bytes(info) * 7) + 1000;
+ mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
+ }
+}
+
static int write(struct tty_struct *tty,
const unsigned char *buf, int count)
{
int ret = 0;
struct slgt_info *info = tty->driver_data;
unsigned long flags;
+ unsigned int bufs_needed;
if (sanity_check(info, tty->name, "write"))
goto cleanup;
if (!count)
goto cleanup;
- if (info->params.mode == MGSL_MODE_RAW ||
- info->params.mode == MGSL_MODE_MONOSYNC ||
- info->params.mode == MGSL_MODE_BISYNC) {
- unsigned int bufs_needed = (count/DMABUFSIZE);
- unsigned int bufs_free = free_tbuf_count(info);
- if (count % DMABUFSIZE)
- ++bufs_needed;
- if (bufs_needed > bufs_free)
- goto cleanup;
- } else {
- if (info->tx_active)
- goto cleanup;
- if (info->tx_count) {
- /* send accumulated data from send_char() calls */
- /* as frame and wait before accepting more data. */
- tx_load(info, info->tx_buf, info->tx_count);
- goto start;
- }
+ if (!info->tx_active && info->tx_count) {
+ /* send accumulated data from send_char() */
+ tx_load(info, info->tx_buf, info->tx_count);
+ goto start;
}
+ bufs_needed = (count/DMABUFSIZE);
+ if (count % DMABUFSIZE)
+ ++bufs_needed;
+ if (bufs_needed > free_tbuf_count(info))
+ goto cleanup;
ret = info->tx_count = count;
tx_load(info, buf, count);
spin_lock_irqsave(&info->lock,flags);
if (!info->tx_active)
tx_start(info);
+ else if (!(rd_reg32(info, TDCSR) & BIT0)) {
+ /* transmit still active but transmit DMA stopped */
+ unsigned int i = info->tbuf_current;
+ if (!i)
+ i = info->tbuf_count;
+ i--;
+ /* if DMA buf unsent must try later after tx idle */
+ if (desc_count(info->tbufs[i]))
+ ret = 0;
+ }
+ if (ret > 0)
+ update_tx_timer(info);
spin_unlock_irqrestore(&info->lock,flags);
}
return ret;
}
-static void put_char(struct tty_struct *tty, unsigned char ch)
+static int put_char(struct tty_struct *tty, unsigned char ch)
{
struct slgt_info *info = tty->driver_data;
unsigned long flags;
+ int ret = 0;
if (sanity_check(info, tty->name, "put_char"))
- return;
+ return 0;
DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
if (!info->tx_buf)
- return;
+ return 0;
spin_lock_irqsave(&info->lock,flags);
- if (!info->tx_active && (info->tx_count < info->max_frame_size))
+ if (!info->tx_active && (info->tx_count < info->max_frame_size)) {
info->tx_buf[info->tx_count++] = ch;
+ ret = 1;
+ }
spin_unlock_irqrestore(&info->lock,flags);
+ return ret;
}
static void send_xchar(struct tty_struct *tty, char ch)
if (sanity_check(info, tty->name, "wait_until_sent"))
return;
DBGINFO(("%s wait_until_sent entry\n", info->device_name));
- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
goto exit;
orig_jiffies = jiffies;
* Note: use tight timings here to satisfy the NIST-PCTS.
*/
+ lock_kernel();
+
if (info->params.data_rate) {
char_time = info->timeout/(32 * 5);
if (!char_time)
if (timeout && time_after(jiffies, orig_jiffies + timeout))
break;
}
+ unlock_kernel();
exit:
DBGINFO(("%s wait_until_sent exit\n", info->device_name));
info->tx_count = 0;
spin_unlock_irqrestore(&info->lock,flags);
- wake_up_interruptible(&tty->write_wait);
tty_wakeup(tty);
}
struct serial_icounter_struct __user *p_cuser; /* user space */
unsigned long flags;
void __user *argp = (void __user *)arg;
+ int ret;
if (sanity_check(info, tty->name, "ioctl"))
return -ENODEV;
return -EIO;
}
+ lock_kernel();
+
switch (cmd) {
case MGSL_IOCGPARAMS:
- return get_params(info, argp);
+ ret = get_params(info, argp);
+ break;
case MGSL_IOCSPARAMS:
- return set_params(info, argp);
+ ret = set_params(info, argp);
+ break;
case MGSL_IOCGTXIDLE:
- return get_txidle(info, argp);
+ ret = get_txidle(info, argp);
+ break;
case MGSL_IOCSTXIDLE:
- return set_txidle(info, (int)arg);
+ ret = set_txidle(info, (int)arg);
+ break;
case MGSL_IOCTXENABLE:
- return tx_enable(info, (int)arg);
+ ret = tx_enable(info, (int)arg);
+ break;
case MGSL_IOCRXENABLE:
- return rx_enable(info, (int)arg);
+ ret = rx_enable(info, (int)arg);
+ break;
case MGSL_IOCTXABORT:
- return tx_abort(info);
+ ret = tx_abort(info);
+ break;
case MGSL_IOCGSTATS:
- return get_stats(info, argp);
+ ret = get_stats(info, argp);
+ break;
case MGSL_IOCWAITEVENT:
- return wait_mgsl_event(info, argp);
+ ret = wait_mgsl_event(info, argp);
+ break;
case TIOCMIWAIT:
- return modem_input_wait(info,(int)arg);
+ ret = modem_input_wait(info,(int)arg);
+ break;
case MGSL_IOCGIF:
- return get_interface(info, argp);
+ ret = get_interface(info, argp);
+ break;
case MGSL_IOCSIF:
- return set_interface(info,(int)arg);
+ ret = set_interface(info,(int)arg);
+ break;
case MGSL_IOCSGPIO:
- return set_gpio(info, argp);
+ ret = set_gpio(info, argp);
+ break;
case MGSL_IOCGGPIO:
- return get_gpio(info, argp);
+ ret = get_gpio(info, argp);
+ break;
case MGSL_IOCWAITGPIO:
- return wait_gpio(info, argp);
+ ret = wait_gpio(info, argp);
+ break;
case TIOCGICOUNT:
spin_lock_irqsave(&info->lock,flags);
cnow = info->icount;
put_user(cnow.parity, &p_cuser->parity) ||
put_user(cnow.brk, &p_cuser->brk) ||
put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
- return -EFAULT;
- return 0;
+ ret = -EFAULT;
+ ret = 0;
+ break;
default:
- return -ENOIOCTLCMD;
+ ret = -ENOIOCTLCMD;
+ }
+ unlock_kernel();
+ return ret;
+}
+
+/*
+ * support for 32 bit ioctl calls on 64 bit systems
+ */
+#ifdef CONFIG_COMPAT
+static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
+{
+ struct MGSL_PARAMS32 tmp_params;
+
+ DBGINFO(("%s get_params32\n", info->device_name));
+ tmp_params.mode = (compat_ulong_t)info->params.mode;
+ tmp_params.loopback = info->params.loopback;
+ tmp_params.flags = info->params.flags;
+ tmp_params.encoding = info->params.encoding;
+ tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed;
+ tmp_params.addr_filter = info->params.addr_filter;
+ tmp_params.crc_type = info->params.crc_type;
+ tmp_params.preamble_length = info->params.preamble_length;
+ tmp_params.preamble = info->params.preamble;
+ tmp_params.data_rate = (compat_ulong_t)info->params.data_rate;
+ tmp_params.data_bits = info->params.data_bits;
+ tmp_params.stop_bits = info->params.stop_bits;
+ tmp_params.parity = info->params.parity;
+ if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
+ return -EFAULT;
+ return 0;
+}
+
+static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
+{
+ struct MGSL_PARAMS32 tmp_params;
+
+ DBGINFO(("%s set_params32\n", info->device_name));
+ if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
+ return -EFAULT;
+
+ spin_lock(&info->lock);
+ if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
+ info->base_clock = tmp_params.clock_speed;
+ } else {
+ info->params.mode = tmp_params.mode;
+ info->params.loopback = tmp_params.loopback;
+ info->params.flags = tmp_params.flags;
+ info->params.encoding = tmp_params.encoding;
+ info->params.clock_speed = tmp_params.clock_speed;
+ info->params.addr_filter = tmp_params.addr_filter;
+ info->params.crc_type = tmp_params.crc_type;
+ info->params.preamble_length = tmp_params.preamble_length;
+ info->params.preamble = tmp_params.preamble;
+ info->params.data_rate = tmp_params.data_rate;
+ info->params.data_bits = tmp_params.data_bits;
+ info->params.stop_bits = tmp_params.stop_bits;
+ info->params.parity = tmp_params.parity;
}
+ spin_unlock(&info->lock);
+
+ program_hw(info);
+
return 0;
}
+static long slgt_compat_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ struct slgt_info *info = tty->driver_data;
+ int rc = -ENOIOCTLCMD;
+
+ if (sanity_check(info, tty->name, "compat_ioctl"))
+ return -ENODEV;
+ DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
+
+ switch (cmd) {
+
+ case MGSL_IOCSPARAMS32:
+ rc = set_params32(info, compat_ptr(arg));
+ break;
+
+ case MGSL_IOCGPARAMS32:
+ rc = get_params32(info, compat_ptr(arg));
+ break;
+
+ case MGSL_IOCGPARAMS:
+ case MGSL_IOCSPARAMS:
+ case MGSL_IOCGTXIDLE:
+ case MGSL_IOCGSTATS:
+ case MGSL_IOCWAITEVENT:
+ case MGSL_IOCGIF:
+ case MGSL_IOCSGPIO:
+ case MGSL_IOCGGPIO:
+ case MGSL_IOCWAITGPIO:
+ case TIOCGICOUNT:
+ rc = ioctl(tty, file, cmd, (unsigned long)(compat_ptr(arg)));
+ break;
+
+ case MGSL_IOCSTXIDLE:
+ case MGSL_IOCTXENABLE:
+ case MGSL_IOCRXENABLE:
+ case MGSL_IOCTXABORT:
+ case TIOCMIWAIT:
+ case MGSL_IOCSIF:
+ rc = ioctl(tty, file, cmd, arg);
+ break;
+ }
+
+ DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
+ return rc;
+}
+#else
+#define slgt_compat_ioctl NULL
+#endif /* ifdef CONFIG_COMPAT */
+
/*
* proc fs support
*/
-static inline int line_info(char *buf, struct slgt_info *info)
+static inline void line_info(struct seq_file *m, struct slgt_info *info)
{
char stat_buf[30];
- int ret;
unsigned long flags;
- ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
+ seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
info->device_name, info->phys_reg_addr,
info->irq_level, info->max_frame_size);
strcat(stat_buf, "|RI");
if (info->params.mode != MGSL_MODE_ASYNC) {
- ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
+ seq_printf(m, "\tHDLC txok:%d rxok:%d",
info->icount.txok, info->icount.rxok);
if (info->icount.txunder)
- ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
+ seq_printf(m, " txunder:%d", info->icount.txunder);
if (info->icount.txabort)
- ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
+ seq_printf(m, " txabort:%d", info->icount.txabort);
if (info->icount.rxshort)
- ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
+ seq_printf(m, " rxshort:%d", info->icount.rxshort);
if (info->icount.rxlong)
- ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
+ seq_printf(m, " rxlong:%d", info->icount.rxlong);
if (info->icount.rxover)
- ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
+ seq_printf(m, " rxover:%d", info->icount.rxover);
if (info->icount.rxcrc)
- ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
+ seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
} else {
- ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
+ seq_printf(m, "\tASYNC tx:%d rx:%d",
info->icount.tx, info->icount.rx);
if (info->icount.frame)
- ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
+ seq_printf(m, " fe:%d", info->icount.frame);
if (info->icount.parity)
- ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
+ seq_printf(m, " pe:%d", info->icount.parity);
if (info->icount.brk)
- ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
+ seq_printf(m, " brk:%d", info->icount.brk);
if (info->icount.overrun)
- ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
+ seq_printf(m, " oe:%d", info->icount.overrun);
}
/* Append serial signal status to end */
- ret += sprintf(buf+ret, " %s\n", stat_buf+1);
+ seq_printf(m, " %s\n", stat_buf+1);
- ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
+ seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
info->tx_active,info->bh_requested,info->bh_running,
info->pending_bh);
-
- return ret;
}
/* Called to print information about devices
*/
-static int read_proc(char *page, char **start, off_t off, int count,
- int *eof, void *data)
+static int synclink_gt_proc_show(struct seq_file *m, void *v)
{
- int len = 0, l;
- off_t begin = 0;
struct slgt_info *info;
- len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
+ seq_puts(m, "synclink_gt driver\n");
info = slgt_device_list;
while( info ) {
- l = line_info(page + len, info);
- len += l;
- if (len+begin > off+count)
- goto done;
- if (len+begin < off) {
- begin += len;
- len = 0;
- }
+ line_info(m, info);
info = info->next_device;
}
+ return 0;
+}
- *eof = 1;
-done:
- if (off >= len+begin)
- return 0;
- *start = page + (off-begin);
- return ((count < begin+len-off) ? count : begin+len-off);
+static int synclink_gt_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, synclink_gt_proc_show, NULL);
}
+static const struct file_operations synclink_gt_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = synclink_gt_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
/*
* return count of bytes in transmit buffer
*/
static int chars_in_buffer(struct tty_struct *tty)
{
struct slgt_info *info = tty->driver_data;
+ int count;
if (sanity_check(info, tty->name, "chars_in_buffer"))
return 0;
- DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
- return info->tx_count;
+ count = tbuf_bytes(info);
+ DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
+ return count;
}
/*
* set or clear transmit break condition
* break_state -1=set break condition, 0=clear
*/
-static void set_break(struct tty_struct *tty, int break_state)
+static int set_break(struct tty_struct *tty, int break_state)
{
struct slgt_info *info = tty->driver_data;
unsigned short value;
unsigned long flags;
if (sanity_check(info, tty->name, "set_break"))
- return;
+ return -EINVAL;
DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
spin_lock_irqsave(&info->lock,flags);
value &= ~BIT6;
wr_reg16(info, TCR, value);
spin_unlock_irqrestore(&info->lock,flags);
+ return 0;
}
#if SYNCLINK_GENERIC_HDLC
unsigned short new_crctype;
/* return error if TTY interface open */
- if (info->count)
+ if (info->port.count)
return -EBUSY;
DBGINFO(("%s hdlcdev_attach\n", info->device_name));
*
* skb socket buffer containing HDLC frame
* dev pointer to network device structure
- *
- * returns 0 if success, otherwise error code
*/
-static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
+ struct net_device *dev)
{
struct slgt_info *info = dev_to_port(dev);
- struct net_device_stats *stats = hdlc_stats(dev);
unsigned long flags;
DBGINFO(("%s hdlc_xmit\n", dev->name));
tx_load(info, skb->data, skb->len);
/* update network statistics */
- stats->tx_packets++;
- stats->tx_bytes += skb->len;
+ dev->stats.tx_packets++;
+ dev->stats.tx_bytes += skb->len;
/* done with socket buffer, so free it */
dev_kfree_skb(skb);
/* save start time for transmit timeout detection */
dev->trans_start = jiffies;
- /* start hardware transmitter if necessary */
spin_lock_irqsave(&info->lock,flags);
- if (!info->tx_active)
- tx_start(info);
+ tx_start(info);
+ update_tx_timer(info);
spin_unlock_irqrestore(&info->lock,flags);
- return 0;
+ return NETDEV_TX_OK;
}
/**
int rc;
unsigned long flags;
+ if (!try_module_get(THIS_MODULE))
+ return -EBUSY;
+
DBGINFO(("%s hdlcdev_open\n", dev->name));
/* generic HDLC layer open processing */
/* arbitrate between network and tty opens */
spin_lock_irqsave(&info->netlock, flags);
- if (info->count != 0 || info->netcount != 0) {
+ if (info->port.count != 0 || info->netcount != 0) {
DBGINFO(("%s hdlc_open busy\n", dev->name));
spin_unlock_irqrestore(&info->netlock, flags);
return -EBUSY;
info->netcount=0;
spin_unlock_irqrestore(&info->netlock, flags);
+ module_put(THIS_MODULE);
return 0;
}
DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
/* return error if TTY interface open */
- if (info->count)
+ if (info->port.count)
return -EBUSY;
if (cmd != SIOCWANDEV)
static void hdlcdev_tx_timeout(struct net_device *dev)
{
struct slgt_info *info = dev_to_port(dev);
- struct net_device_stats *stats = hdlc_stats(dev);
unsigned long flags;
DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
- stats->tx_errors++;
- stats->tx_aborted_errors++;
+ dev->stats.tx_errors++;
+ dev->stats.tx_aborted_errors++;
spin_lock_irqsave(&info->lock,flags);
tx_stop(info);
{
struct sk_buff *skb = dev_alloc_skb(size);
struct net_device *dev = info->netdev;
- struct net_device_stats *stats = hdlc_stats(dev);
DBGINFO(("%s hdlcdev_rx\n", dev->name));
if (skb == NULL) {
DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
- stats->rx_dropped++;
+ dev->stats.rx_dropped++;
return;
}
- memcpy(skb_put(skb, size),buf,size);
+ memcpy(skb_put(skb, size), buf, size);
- skb->protocol = hdlc_type_trans(skb, info->netdev);
+ skb->protocol = hdlc_type_trans(skb, dev);
- stats->rx_packets++;
- stats->rx_bytes += size;
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += size;
netif_rx(skb);
-
- info->netdev->last_rx = jiffies;
}
+static const struct net_device_ops hdlcdev_ops = {
+ .ndo_open = hdlcdev_open,
+ .ndo_stop = hdlcdev_close,
+ .ndo_change_mtu = hdlc_change_mtu,
+ .ndo_start_xmit = hdlc_start_xmit,
+ .ndo_do_ioctl = hdlcdev_ioctl,
+ .ndo_tx_timeout = hdlcdev_tx_timeout,
+};
+
/**
* called by device driver when adding device instance
* do generic HDLC initialization
dev->irq = info->irq_level;
/* network layer callbacks and settings */
- dev->do_ioctl = hdlcdev_ioctl;
- dev->open = hdlcdev_open;
- dev->stop = hdlcdev_close;
- dev->tx_timeout = hdlcdev_tx_timeout;
- dev->watchdog_timeo = 10*HZ;
+ dev->netdev_ops = &hdlcdev_ops;
+ dev->watchdog_timeo = 10 * HZ;
dev->tx_queue_len = 50;
/* generic HDLC layer callbacks and settings */
*/
static void rx_async(struct slgt_info *info)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
struct mgsl_icount *icount = &info->icount;
unsigned int start, end;
unsigned char *p;
if (i < count) {
/* receive buffer not completed */
info->rbuf_index += i;
- info->rx_timer.expires = jiffies + 1;
- add_timer(&info->rx_timer);
+ mod_timer(&info->rx_timer, jiffies + 1);
break;
}
rc = BH_STATUS;
} else {
/* Mark BH routine as complete */
- info->bh_running = 0;
- info->bh_requested = 0;
+ info->bh_running = false;
+ info->bh_requested = false;
rc = 0;
}
if (!info)
return;
- info->bh_running = 1;
+ info->bh_running = true;
while((action = bh_action(info))) {
switch (action) {
static void bh_transmit(struct slgt_info *info)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
DBGBH(("%s bh_transmit\n", info->device_name));
- if (tty) {
+ if (tty)
tty_wakeup(tty);
- wake_up_interruptible(&tty->write_wait);
- }
}
-static void dsr_change(struct slgt_info *info)
+static void dsr_change(struct slgt_info *info, unsigned short status)
{
- get_signals(info);
+ if (status & BIT3) {
+ info->signals |= SerialSignal_DSR;
+ info->input_signal_events.dsr_up++;
+ } else {
+ info->signals &= ~SerialSignal_DSR;
+ info->input_signal_events.dsr_down++;
+ }
DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
slgt_irq_off(info, IRQ_DSR);
return;
}
info->icount.dsr++;
- if (info->signals & SerialSignal_DSR)
- info->input_signal_events.dsr_up++;
- else
- info->input_signal_events.dsr_down++;
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
info->pending_bh |= BH_STATUS;
}
-static void cts_change(struct slgt_info *info)
+static void cts_change(struct slgt_info *info, unsigned short status)
{
- get_signals(info);
+ if (status & BIT2) {
+ info->signals |= SerialSignal_CTS;
+ info->input_signal_events.cts_up++;
+ } else {
+ info->signals &= ~SerialSignal_CTS;
+ info->input_signal_events.cts_down++;
+ }
DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
slgt_irq_off(info, IRQ_CTS);
return;
}
info->icount.cts++;
- if (info->signals & SerialSignal_CTS)
- info->input_signal_events.cts_up++;
- else
- info->input_signal_events.cts_down++;
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
info->pending_bh |= BH_STATUS;
- if (info->flags & ASYNC_CTS_FLOW) {
- if (info->tty) {
- if (info->tty->hw_stopped) {
+ if (info->port.flags & ASYNC_CTS_FLOW) {
+ if (info->port.tty) {
+ if (info->port.tty->hw_stopped) {
if (info->signals & SerialSignal_CTS) {
- info->tty->hw_stopped = 0;
+ info->port.tty->hw_stopped = 0;
info->pending_bh |= BH_TRANSMIT;
return;
}
} else {
if (!(info->signals & SerialSignal_CTS))
- info->tty->hw_stopped = 1;
+ info->port.tty->hw_stopped = 1;
}
}
}
}
-static void dcd_change(struct slgt_info *info)
+static void dcd_change(struct slgt_info *info, unsigned short status)
{
- get_signals(info);
+ if (status & BIT1) {
+ info->signals |= SerialSignal_DCD;
+ info->input_signal_events.dcd_up++;
+ } else {
+ info->signals &= ~SerialSignal_DCD;
+ info->input_signal_events.dcd_down++;
+ }
DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
slgt_irq_off(info, IRQ_DCD);
return;
}
info->icount.dcd++;
- if (info->signals & SerialSignal_DCD) {
- info->input_signal_events.dcd_up++;
- } else {
- info->input_signal_events.dcd_down++;
- }
#if SYNCLINK_GENERIC_HDLC
if (info->netcount) {
if (info->signals & SerialSignal_DCD)
wake_up_interruptible(&info->event_wait_q);
info->pending_bh |= BH_STATUS;
- if (info->flags & ASYNC_CHECK_CD) {
+ if (info->port.flags & ASYNC_CHECK_CD) {
if (info->signals & SerialSignal_DCD)
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
else {
- if (info->tty)
- tty_hangup(info->tty);
+ if (info->port.tty)
+ tty_hangup(info->port.tty);
}
}
}
-static void ri_change(struct slgt_info *info)
+static void ri_change(struct slgt_info *info, unsigned short status)
{
- get_signals(info);
+ if (status & BIT0) {
+ info->signals |= SerialSignal_RI;
+ info->input_signal_events.ri_up++;
+ } else {
+ info->signals &= ~SerialSignal_RI;
+ info->input_signal_events.ri_down++;
+ }
DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
slgt_irq_off(info, IRQ_RI);
return;
}
- info->icount.dcd++;
- if (info->signals & SerialSignal_RI) {
- info->input_signal_events.ri_up++;
- } else {
- info->input_signal_events.ri_down++;
- }
+ info->icount.rng++;
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
info->pending_bh |= BH_STATUS;
}
+static void isr_rxdata(struct slgt_info *info)
+{
+ unsigned int count = info->rbuf_fill_count;
+ unsigned int i = info->rbuf_fill_index;
+ unsigned short reg;
+
+ while (rd_reg16(info, SSR) & IRQ_RXDATA) {
+ reg = rd_reg16(info, RDR);
+ DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
+ if (desc_complete(info->rbufs[i])) {
+ /* all buffers full */
+ rx_stop(info);
+ info->rx_restart = 1;
+ continue;
+ }
+ info->rbufs[i].buf[count++] = (unsigned char)reg;
+ /* async mode saves status byte to buffer for each data byte */
+ if (info->params.mode == MGSL_MODE_ASYNC)
+ info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
+ if (count == info->rbuf_fill_level || (reg & BIT10)) {
+ /* buffer full or end of frame */
+ set_desc_count(info->rbufs[i], count);
+ set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
+ info->rbuf_fill_count = count = 0;
+ if (++i == info->rbuf_count)
+ i = 0;
+ info->pending_bh |= BH_RECEIVE;
+ }
+ }
+
+ info->rbuf_fill_index = i;
+ info->rbuf_fill_count = count;
+}
+
static void isr_serial(struct slgt_info *info)
{
unsigned short status = rd_reg16(info, SSR);
wr_reg16(info, SSR, status); /* clear pending */
- info->irq_occurred = 1;
+ info->irq_occurred = true;
if (info->params.mode == MGSL_MODE_ASYNC) {
if (status & IRQ_TXIDLE) {
if (info->tx_count)
isr_txeom(info, status);
}
+ if (info->rx_pio && (status & IRQ_RXDATA))
+ isr_rxdata(info);
if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
info->icount.brk++;
/* process break detection if tty control allows */
- if (info->tty) {
+ if (info->port.tty) {
if (!(status & info->ignore_status_mask)) {
if (info->read_status_mask & MASK_BREAK) {
- tty_insert_flip_char(info->tty, 0, TTY_BREAK);
- if (info->flags & ASYNC_SAK)
- do_SAK(info->tty);
+ tty_insert_flip_char(info->port.tty, 0, TTY_BREAK);
+ if (info->port.flags & ASYNC_SAK)
+ do_SAK(info->port.tty);
}
}
}
} else {
if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
isr_txeom(info, status);
-
+ if (info->rx_pio && (status & IRQ_RXDATA))
+ isr_rxdata(info);
if (status & IRQ_RXIDLE) {
if (status & RXIDLE)
info->icount.rxidle++;
}
if (status & IRQ_DSR)
- dsr_change(info);
+ dsr_change(info, status);
if (status & IRQ_CTS)
- cts_change(info);
+ cts_change(info, status);
if (status & IRQ_DCD)
- dcd_change(info);
+ dcd_change(info, status);
if (status & IRQ_RI)
- ri_change(info);
+ ri_change(info, status);
}
static void isr_rdma(struct slgt_info *info)
if (status & (BIT5 + BIT4)) {
DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
- info->rx_restart = 1;
+ info->rx_restart = true;
}
info->pending_bh |= BH_RECEIVE;
}
info->icount.txok++;
}
- info->tx_active = 0;
+ info->tx_active = false;
info->tx_count = 0;
del_timer(&info->tx_timer);
if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
info->signals &= ~SerialSignal_RTS;
- info->drop_rts_on_tx_done = 0;
+ info->drop_rts_on_tx_done = false;
set_signals(info);
}
else
#endif
{
- if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
+ if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
tx_stop(info);
return;
}
* irq interrupt number
* dev_id device ID supplied during interrupt registration
*/
-static irqreturn_t slgt_interrupt(int irq, void *dev_id)
+static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
{
- struct slgt_info *info;
+ struct slgt_info *info = dev_id;
unsigned int gsr;
unsigned int i;
- DBGISR(("slgt_interrupt irq=%d entry\n", irq));
-
- info = dev_id;
- if (!info)
- return IRQ_NONE;
+ DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
spin_lock(&info->lock);
while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
- info->irq_occurred = 1;
+ info->irq_occurred = true;
for(i=0; i < info->port_count ; i++) {
if (info->port_array[i] == NULL)
continue;
for(i=0; i < info->port_count ; i++) {
struct slgt_info *port = info->port_array[i];
- if (port && (port->count || port->netcount) &&
+ if (port && (port->port.count || port->netcount) &&
port->pending_bh && !port->bh_running &&
!port->bh_requested) {
DBGISR(("%s bh queued\n", port->device_name));
schedule_work(&port->task);
- port->bh_requested = 1;
+ port->bh_requested = true;
}
}
spin_unlock(&info->lock);
- DBGISR(("slgt_interrupt irq=%d exit\n", irq));
+ DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
return IRQ_HANDLED;
}
{
DBGINFO(("%s startup\n", info->device_name));
- if (info->flags & ASYNC_INITIALIZED)
+ if (info->port.flags & ASYNC_INITIALIZED)
return 0;
if (!info->tx_buf) {
/* program hardware for current parameters */
change_params(info);
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->flags |= ASYNC_INITIALIZED;
+ info->port.flags |= ASYNC_INITIALIZED;
return 0;
}
{
unsigned long flags;
- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
return;
DBGINFO(("%s shutdown\n", info->device_name));
slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
- if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
+ if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
set_signals(info);
}
spin_unlock_irqrestore(&info->lock,flags);
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->flags &= ~ASYNC_INITIALIZED;
+ info->port.flags &= ~ASYNC_INITIALIZED;
}
static void program_hw(struct slgt_info *info)
info->ri_chkcount = 0;
info->dsr_chkcount = 0;
- slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
+ slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
get_signals(info);
if (info->netcount ||
- (info->tty && info->tty->termios->c_cflag & CREAD))
+ (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
rx_start(info);
spin_unlock_irqrestore(&info->lock,flags);
unsigned cflag;
int bits_per_char;
- if (!info->tty || !info->tty->termios)
+ if (!info->port.tty || !info->port.tty->termios)
return;
DBGINFO(("%s change_params\n", info->device_name));
- cflag = info->tty->termios->c_cflag;
+ cflag = info->port.tty->termios->c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
bits_per_char = info->params.data_bits +
info->params.stop_bits + 1;
- info->params.data_rate = tty_get_baud_rate(info->tty);
+ info->params.data_rate = tty_get_baud_rate(info->port.tty);
if (info->params.data_rate) {
info->timeout = (32*HZ*bits_per_char) /
info->timeout += HZ/50; /* Add .02 seconds of slop */
if (cflag & CRTSCTS)
- info->flags |= ASYNC_CTS_FLOW;
+ info->port.flags |= ASYNC_CTS_FLOW;
else
- info->flags &= ~ASYNC_CTS_FLOW;
+ info->port.flags &= ~ASYNC_CTS_FLOW;
if (cflag & CLOCAL)
- info->flags &= ~ASYNC_CHECK_CD;
+ info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->flags |= ASYNC_CHECK_CD;
+ info->port.flags |= ASYNC_CHECK_CD;
/* process tty input control flags */
info->read_status_mask = IRQ_RXOVER;
- if (I_INPCK(info->tty))
+ if (I_INPCK(info->port.tty))
info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
- if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
+ if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
info->read_status_mask |= MASK_BREAK;
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
- if (I_IGNBRK(info->tty)) {
+ if (I_IGNBRK(info->port.tty)) {
info->ignore_status_mask |= MASK_BREAK;
/* If ignoring parity and break indicators, ignore
* overruns too. (For real raw support).
*/
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
info->ignore_status_mask |= MASK_OVERRUN;
}
return -EFAULT;
spin_lock_irqsave(&info->lock, flags);
- memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
+ if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
+ info->base_clock = tmp_params.clock_speed;
+ else
+ memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
spin_unlock_irqrestore(&info->lock, flags);
- change_params(info);
+ program_hw(info);
return 0;
}
static int rx_enable(struct slgt_info *info, int enable)
{
unsigned long flags;
- DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
+ unsigned int rbuf_fill_level;
+ DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
spin_lock_irqsave(&info->lock,flags);
+ /*
+ * enable[31..16] = receive DMA buffer fill level
+ * 0 = noop (leave fill level unchanged)
+ * fill level must be multiple of 4 and <= buffer size
+ */
+ rbuf_fill_level = ((unsigned int)enable) >> 16;
+ if (rbuf_fill_level) {
+ if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
+ spin_unlock_irqrestore(&info->lock, flags);
+ return -EINVAL;
+ }
+ info->rbuf_fill_level = rbuf_fill_level;
+ if (rbuf_fill_level < 128)
+ info->rx_pio = 1; /* PIO mode */
+ else
+ info->rx_pio = 0; /* DMA mode */
+ rx_stop(info); /* restart receiver to use new fill level */
+ }
+
+ /*
+ * enable[1..0] = receiver enable command
+ * 0 = disable
+ * 1 = enable
+ * 2 = enable or force hunt mode if already enabled
+ */
+ enable &= 3;
if (enable) {
if (!info->rx_enabled)
rx_start(info);
return 0;
}
+static int carrier_raised(struct tty_port *port)
+{
+ unsigned long flags;
+ struct slgt_info *info = container_of(port, struct slgt_info, port);
+
+ spin_lock_irqsave(&info->lock,flags);
+ get_signals(info);
+ spin_unlock_irqrestore(&info->lock,flags);
+ return (info->signals & SerialSignal_DCD) ? 1 : 0;
+}
+
+static void dtr_rts(struct tty_port *port, int on)
+{
+ unsigned long flags;
+ struct slgt_info *info = container_of(port, struct slgt_info, port);
+
+ spin_lock_irqsave(&info->lock,flags);
+ if (on)
+ info->signals |= SerialSignal_RTS + SerialSignal_DTR;
+ else
+ info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
+ set_signals(info);
+ spin_unlock_irqrestore(&info->lock,flags);
+}
+
+
/*
* block current process until the device is ready to open
*/
{
DECLARE_WAITQUEUE(wait, current);
int retval;
- int do_clocal = 0, extra_count = 0;
+ bool do_clocal = false;
+ bool extra_count = false;
unsigned long flags;
+ int cd;
+ struct tty_port *port = &info->port;
DBGINFO(("%s block_til_ready\n", tty->driver->name));
if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
/* nonblock mode is set or port is not enabled */
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
if (tty->termios->c_cflag & CLOCAL)
- do_clocal = 1;
+ do_clocal = true;
/* Wait for carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
- * this loop, info->count is dropped by one, so that
+ * this loop, port->count is dropped by one, so that
* close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
- add_wait_queue(&info->open_wait, &wait);
+ add_wait_queue(&port->open_wait, &wait);
spin_lock_irqsave(&info->lock, flags);
if (!tty_hung_up_p(filp)) {
- extra_count = 1;
- info->count--;
+ extra_count = true;
+ port->count--;
}
spin_unlock_irqrestore(&info->lock, flags);
- info->blocked_open++;
+ port->blocked_open++;
while (1) {
- if ((tty->termios->c_cflag & CBAUD)) {
- spin_lock_irqsave(&info->lock,flags);
- info->signals |= SerialSignal_RTS + SerialSignal_DTR;
- set_signals(info);
- spin_unlock_irqrestore(&info->lock,flags);
- }
+ if ((tty->termios->c_cflag & CBAUD))
+ tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
- retval = (info->flags & ASYNC_HUP_NOTIFY) ?
+ if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+ retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
}
- spin_lock_irqsave(&info->lock,flags);
- get_signals(info);
- spin_unlock_irqrestore(&info->lock,flags);
+ cd = tty_port_carrier_raised(port);
- if (!(info->flags & ASYNC_CLOSING) &&
- (do_clocal || (info->signals & SerialSignal_DCD)) ) {
+ if (!(port->flags & ASYNC_CLOSING) && (do_clocal || cd ))
break;
- }
if (signal_pending(current)) {
retval = -ERESTARTSYS;
}
set_current_state(TASK_RUNNING);
- remove_wait_queue(&info->open_wait, &wait);
+ remove_wait_queue(&port->open_wait, &wait);
if (extra_count)
- info->count++;
- info->blocked_open--;
+ port->count++;
+ port->blocked_open--;
if (!retval)
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
return retval;
goto errout;
}
else
- info->reg_addr_requested = 1;
+ info->reg_addr_requested = true;
- info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
+ info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
if (!info->reg_addr) {
DBGERR(("%s cant map device registers, addr=%08X\n",
info->device_name, info->phys_reg_addr));
{
if (info->irq_requested) {
free_irq(info->irq_level, info);
- info->irq_requested = 0;
+ info->irq_requested = false;
}
if (info->reg_addr_requested) {
release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
- info->reg_addr_requested = 0;
+ info->reg_addr_requested = false;
}
if (info->reg_addr) {
if (info->line < MAX_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
slgt_device_count++;
#endif
}
+static const struct tty_port_operations slgt_port_ops = {
+ .carrier_raised = carrier_raised,
+ .dtr_rts = dtr_rts,
+};
+
/*
* allocate device instance structure, return NULL on failure
*/
{
struct slgt_info *info;
- info = kmalloc(sizeof(struct slgt_info), GFP_KERNEL);
+ info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
if (!info) {
DBGERR(("%s device alloc failed adapter=%d port=%d\n",
driver_name, adapter_num, port_num));
} else {
- memset(info, 0, sizeof(struct slgt_info));
+ tty_port_init(&info->port);
+ info->port.ops = &slgt_port_ops;
info->magic = MGSL_MAGIC;
INIT_WORK(&info->task, bh_handler);
info->max_frame_size = 4096;
- info->raw_rx_size = DMABUFSIZE;
- info->close_delay = 5*HZ/10;
- info->closing_wait = 30*HZ;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
+ info->base_clock = 14745600;
+ info->rbuf_fill_level = DMABUFSIZE;
+ info->port.close_delay = 5*HZ/10;
+ info->port.closing_wait = 30*HZ;
init_waitqueue_head(&info->status_event_wait_q);
init_waitqueue_head(&info->event_wait_q);
spin_lock_init(&info->netlock);
info->adapter_num = adapter_num;
info->port_num = port_num;
- init_timer(&info->tx_timer);
- info->tx_timer.data = (unsigned long)info;
- info->tx_timer.function = tx_timeout;
-
- init_timer(&info->rx_timer);
- info->rx_timer.data = (unsigned long)info;
- info->rx_timer.function = rx_timeout;
+ setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
+ setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
/* Copy configuration info to device instance data */
info->pdev = pdev;
port_array[0]->device_name,
port_array[0]->irq_level));
} else {
- port_array[0]->irq_requested = 1;
+ port_array[0]->irq_requested = true;
adapter_test(port_array[0]);
for (i=1 ; i < port_count ; i++) {
port_array[i]->init_error = port_array[0]->init_error;
}
}
}
+
+ for (i=0; i < port_count; ++i)
+ tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev));
}
static int __devinit init_one(struct pci_dev *dev,
.chars_in_buffer = chars_in_buffer,
.flush_buffer = flush_buffer,
.ioctl = ioctl,
+ .compat_ioctl = slgt_compat_ioctl,
.throttle = throttle,
.unthrottle = unthrottle,
.send_xchar = send_xchar,
.break_ctl = set_break,
.wait_until_sent = wait_until_sent,
- .read_proc = read_proc,
.set_termios = set_termios,
.stop = tx_hold,
.start = tx_release,
.hangup = hangup,
.tiocmget = tiocmget,
.tiocmset = tiocmset,
+ .proc_fops = &synclink_gt_proc_fops,
};
static void slgt_cleanup(void)
struct slgt_info *info;
struct slgt_info *tmp;
- printk("unload %s %s\n", driver_name, driver_version);
+ printk(KERN_INFO "unload %s\n", driver_name);
if (serial_driver) {
+ for (info=slgt_device_list ; info != NULL ; info=info->next_device)
+ tty_unregister_device(serial_driver, info->line);
if ((rc = tty_unregister_driver(serial_driver)))
DBGERR(("tty_unregister_driver error=%d\n", rc));
put_tty_driver(serial_driver);
{
int rc;
- printk("%s %s\n", driver_name, driver_version);
-
- slgt_device_count = 0;
- if ((rc = pci_register_driver(&pci_driver)) < 0) {
- printk("%s pci_register_driver error=%d\n", driver_name, rc);
- return rc;
- }
- pci_registered = 1;
-
- if (!slgt_device_list) {
- printk("%s no devices found\n",driver_name);
- pci_unregister_driver(&pci_driver);
- return -ENODEV;
- }
+ printk(KERN_INFO "%s\n", driver_name);
serial_driver = alloc_tty_driver(MAX_DEVICES);
if (!serial_driver) {
- rc = -ENOMEM;
- goto error;
+ printk("%s can't allocate tty driver\n", driver_name);
+ return -ENOMEM;
}
/* Initialize the tty_driver structure */
B9600 | CS8 | CREAD | HUPCL | CLOCAL;
serial_driver->init_termios.c_ispeed = 9600;
serial_driver->init_termios.c_ospeed = 9600;
- serial_driver->flags = TTY_DRIVER_REAL_RAW;
+ serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
tty_set_operations(serial_driver, &ops);
if ((rc = tty_register_driver(serial_driver)) < 0) {
DBGERR(("%s can't register serial driver\n", driver_name));
goto error;
}
- printk("%s %s, tty major#%d\n",
- driver_name, driver_version,
- serial_driver->major);
+ printk(KERN_INFO "%s, tty major#%d\n",
+ driver_name, serial_driver->major);
+
+ slgt_device_count = 0;
+ if ((rc = pci_register_driver(&pci_driver)) < 0) {
+ printk("%s pci_register_driver error=%d\n", driver_name, rc);
+ goto error;
+ }
+ pci_registered = true;
+
+ if (!slgt_device_list)
+ printk("%s no devices found\n",driver_name);
return 0;
static void set_rate(struct slgt_info *info, u32 rate)
{
unsigned int div;
- static unsigned int osc = 14745600;
+ unsigned int osc = info->base_clock;
/* div = osc/rate - 1
*
rdma_reset(info);
- info->rx_enabled = 0;
- info->rx_restart = 0;
+ info->rx_enabled = false;
+ info->rx_restart = false;
}
static void rx_start(struct slgt_info *info)
rdma_reset(info);
reset_rbufs(info);
- /* set 1st descriptor address */
- wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
-
- if (info->params.mode != MGSL_MODE_ASYNC) {
- /* enable rx DMA and DMA interrupt */
- wr_reg32(info, RDCSR, (BIT2 + BIT0));
+ if (info->rx_pio) {
+ /* rx request when rx FIFO not empty */
+ wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
+ slgt_irq_on(info, IRQ_RXDATA);
+ if (info->params.mode == MGSL_MODE_ASYNC) {
+ /* enable saving of rx status */
+ wr_reg32(info, RDCSR, BIT6);
+ }
} else {
- /* enable saving of rx status, rx DMA and DMA interrupt */
- wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
+ /* rx request when rx FIFO half full */
+ wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
+ /* set 1st descriptor address */
+ wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
+
+ if (info->params.mode != MGSL_MODE_ASYNC) {
+ /* enable rx DMA and DMA interrupt */
+ wr_reg32(info, RDCSR, (BIT2 + BIT0));
+ } else {
+ /* enable saving of rx status, rx DMA and DMA interrupt */
+ wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
+ }
}
slgt_irq_on(info, IRQ_RXOVER);
/* enable receiver */
wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
- info->rx_restart = 0;
- info->rx_enabled = 1;
+ info->rx_restart = false;
+ info->rx_enabled = true;
}
static void tx_start(struct slgt_info *info)
if (!info->tx_enabled) {
wr_reg16(info, TCR,
(unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
- info->tx_enabled = TRUE;
+ info->tx_enabled = true;
}
if (info->tx_count) {
- info->drop_rts_on_tx_done = 0;
+ info->drop_rts_on_tx_done = false;
if (info->params.mode != MGSL_MODE_ASYNC) {
if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
if (!(info->signals & SerialSignal_RTS)) {
info->signals |= SerialSignal_RTS;
set_signals(info);
- info->drop_rts_on_tx_done = 1;
+ info->drop_rts_on_tx_done = true;
}
}
slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
/* clear tx idle and underrun status bits */
wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
-
- if (!(rd_reg32(info, TDCSR) & BIT0)) {
- /* tx DMA stopped, restart tx DMA */
- tdma_reset(info);
- /* set 1st descriptor address */
- wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
- switch(info->params.mode) {
- case MGSL_MODE_RAW:
- case MGSL_MODE_MONOSYNC:
- case MGSL_MODE_BISYNC:
- wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
- break;
- default:
- wr_reg32(info, TDCSR, BIT0); /* DMA enable */
- }
- }
-
- if (info->params.mode == MGSL_MODE_HDLC) {
- info->tx_timer.expires = jiffies + msecs_to_jiffies(5000);
- add_timer(&info->tx_timer);
- }
} else {
- tdma_reset(info);
- /* set 1st descriptor address */
- wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
-
slgt_irq_off(info, IRQ_TXDATA);
slgt_irq_on(info, IRQ_TXIDLE);
/* clear tx idle status bit */
wr_reg16(info, SSR, IRQ_TXIDLE);
-
- /* enable tx DMA */
- wr_reg32(info, TDCSR, BIT0);
}
-
- info->tx_active = 1;
+ /* set 1st descriptor address and start DMA */
+ wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
+ wr_reg32(info, TDCSR, BIT2 + BIT0);
+ info->tx_active = true;
}
}
reset_tbufs(info);
- info->tx_enabled = 0;
- info->tx_active = 0;
+ info->tx_enabled = false;
+ info->tx_active = false;
}
static void reset_port(struct slgt_info *info)
* 06 CTS IRQ enable
* 05 DCD IRQ enable
* 04 RI IRQ enable
- * 03 reserved, must be zero
+ * 03 0=16x sampling, 1=8x sampling
* 02 1=txd->rxd internal loopback enable
* 01 reserved, must be zero
* 00 1=master IRQ enable
*/
val = BIT15 + BIT14 + BIT0;
+ /* JCR[8] : 1 = x8 async mode feature available */
+ if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
+ ((info->base_clock < (info->params.data_rate * 16)) ||
+ (info->base_clock % (info->params.data_rate * 16)))) {
+ /* use 8x sampling */
+ val |= BIT3;
+ set_rate(info, info->params.data_rate * 8);
+ } else {
+ /* use 16x sampling */
+ set_rate(info, info->params.data_rate * 16);
+ }
wr_reg16(info, SCR, val);
slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
- set_rate(info, info->params.data_rate * 16);
-
if (info->params.loopback)
enable_loopback(info);
}
* 01 enable
* 00 auto-CTS enable
*/
- val = 0;
+ val = BIT2;
switch(info->params.mode) {
case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
break;
}
+ if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
+ val |= BIT4;
if (info->signals & SerialSignal_DTR)
val |= BIT3;
if (info->signals & SerialSignal_RTS)
while(!done) {
/* reset current buffer for reuse */
info->rbufs[i].status = 0;
- switch(info->params.mode) {
- case MGSL_MODE_RAW:
- case MGSL_MODE_MONOSYNC:
- case MGSL_MODE_BISYNC:
- set_desc_count(info->rbufs[i], info->raw_rx_size);
- break;
- default:
- set_desc_count(info->rbufs[i], DMABUFSIZE);
- }
-
+ set_desc_count(info->rbufs[i], info->rbuf_fill_level);
if (i == last)
done = 1;
if (++i == info->rbuf_count)
static void reset_rbufs(struct slgt_info *info)
{
free_rbufs(info, 0, info->rbuf_count - 1);
+ info->rbuf_fill_index = 0;
+ info->rbuf_fill_count = 0;
}
/*
* pass receive HDLC frame to upper layer
*
- * return 1 if frame available, otherwise 0
+ * return true if frame available, otherwise false
*/
-static int rx_get_frame(struct slgt_info *info)
+static bool rx_get_frame(struct slgt_info *info)
{
unsigned int start, end;
unsigned short status;
unsigned int framesize = 0;
- int rc = 0;
unsigned long flags;
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
unsigned char addr_field = 0xff;
unsigned int crc_size = 0;
#if SYNCLINK_GENERIC_HDLC
if (framesize == 0) {
- struct net_device_stats *stats = hdlc_stats(info->netdev);
- stats->rx_errors++;
- stats->rx_frame_errors++;
+ info->netdev->stats.rx_errors++;
+ info->netdev->stats.rx_frame_errors++;
}
#endif
DBGBH(("%s rx frame status=%04X size=%d\n",
info->device_name, status, framesize));
- DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
+ DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
if (framesize) {
if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
info->icount.rxok++;
while(copy_count) {
- int partial_count = min(copy_count, DMABUFSIZE);
+ int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
memcpy(p, info->rbufs[i].buf, partial_count);
p += partial_count;
copy_count -= partial_count;
}
}
free_rbufs(info, start, end);
- rc = 1;
+ return true;
cleanup:
- return rc;
+ return false;
}
/*
* pass receive buffer (RAW synchronous mode) to tty layer
- * return 1 if buffer available, otherwise 0
+ * return true if buffer available, otherwise false
*/
-static int rx_get_buf(struct slgt_info *info)
+static bool rx_get_buf(struct slgt_info *info)
{
unsigned int i = info->rbuf_current;
unsigned int count;
if (!desc_complete(info->rbufs[i]))
- return 0;
+ return false;
count = desc_count(info->rbufs[i]);
switch(info->params.mode) {
case MGSL_MODE_MONOSYNC:
DBGDATA(info, info->rbufs[i].buf, count, "rx");
DBGINFO(("rx_get_buf size=%d\n", count));
if (count)
- ldisc_receive_buf(info->tty, info->rbufs[i].buf,
+ ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
info->flag_buf, count);
free_rbufs(info, i, i);
- return 1;
+ return true;
}
static void reset_tbufs(struct slgt_info *info)
i=0;
} while (i != info->tbuf_current);
- /* last buffer with zero count may be in use, assume it is */
- if (count)
+ /* if tx DMA active, last zero count buffer is in use */
+ if (count && (rd_reg32(info, TDCSR) & BIT0))
--count;
return count;
}
/*
+ * return number of bytes in unsent transmit DMA buffers
+ * and the serial controller tx FIFO
+ */
+static unsigned int tbuf_bytes(struct slgt_info *info)
+{
+ unsigned int total_count = 0;
+ unsigned int i = info->tbuf_current;
+ unsigned int reg_value;
+ unsigned int count;
+ unsigned int active_buf_count = 0;
+
+ /*
+ * Add descriptor counts for all tx DMA buffers.
+ * If count is zero (cleared by DMA controller after read),
+ * the buffer is complete or is actively being read from.
+ *
+ * Record buf_count of last buffer with zero count starting
+ * from current ring position. buf_count is mirror
+ * copy of count and is not cleared by serial controller.
+ * If DMA controller is active, that buffer is actively
+ * being read so add to total.
+ */
+ do {
+ count = desc_count(info->tbufs[i]);
+ if (count)
+ total_count += count;
+ else if (!total_count)
+ active_buf_count = info->tbufs[i].buf_count;
+ if (++i == info->tbuf_count)
+ i = 0;
+ } while (i != info->tbuf_current);
+
+ /* read tx DMA status register */
+ reg_value = rd_reg32(info, TDCSR);
+
+ /* if tx DMA active, last zero count buffer is in use */
+ if (reg_value & BIT0)
+ total_count += active_buf_count;
+
+ /* add tx FIFO count = reg_value[15..8] */
+ total_count += (reg_value >> 8) & 0xff;
+
+ /* if transmitter active add one byte for shift register */
+ if (info->tx_active)
+ total_count++;
+
+ return total_count;
+}
+
+/*
* load transmit DMA buffer(s) with data
*/
static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
set_desc_eof(*d, 0);
set_desc_count(*d, count);
+ d->buf_count = count;
}
info->tbuf_current = i;
{
unsigned long timeout;
unsigned long flags;
- struct tty_struct *oldtty = info->tty;
+ struct tty_struct *oldtty = info->port.tty;
u32 speed = info->params.data_rate;
info->params.data_rate = 921600;
- info->tty = NULL;
+ info->port.tty = NULL;
spin_lock_irqsave(&info->lock, flags);
async_mode(info);
/* assume failure */
info->init_error = DiagStatus_IrqFailure;
- info->irq_occurred = FALSE;
+ info->irq_occurred = false;
spin_unlock_irqrestore(&info->lock, flags);
spin_unlock_irqrestore(&info->lock,flags);
info->params.data_rate = speed;
- info->tty = oldtty;
+ info->port.tty = oldtty;
info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
return info->irq_occurred ? 0 : -ENODEV;
int rc = -ENODEV;
unsigned long flags;
- struct tty_struct *oldtty = info->tty;
+ struct tty_struct *oldtty = info->port.tty;
MGSL_PARAMS params;
memcpy(¶ms, &info->params, sizeof(params));
info->params.mode = MGSL_MODE_ASYNC;
info->params.data_rate = 921600;
info->params.loopback = 1;
- info->tty = NULL;
+ info->port.tty = NULL;
/* build and send transmit frame */
for (count = 0; count < TESTFRAMESIZE; ++count)
spin_unlock_irqrestore(&info->lock,flags);
memcpy(&info->params, ¶ms, sizeof(info->params));
- info->tty = oldtty;
+ info->port.tty = oldtty;
info->init_error = rc ? DiagStatus_DmaFailure : 0;
return rc;
info->icount.txtimeout++;
}
spin_lock_irqsave(&info->lock,flags);
- info->tx_active = 0;
- info->tx_count = 0;
+ tx_stop(info);
spin_unlock_irqrestore(&info->lock,flags);
#if SYNCLINK_GENERIC_HDLC
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff