* (at your option) any later version.
*
* Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
- * <alan@redhat.com>. The original 1.8 code is available on www.moxa.com.
+ * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
+ * www.moxa.com.
* - Fixed x86_64 cleanness
*/
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/sched.h>
+#include <linux/smp_lock.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/tty.h>
#include "mxser.h"
-#define MXSER_VERSION "2.0.4" /* 1.12 */
+#define MXSER_VERSION "2.0.5" /* 1.14 */
#define MXSERMAJOR 174
#define MXSER_BOARDS 4 /* Max. boards */
#define PCI_DEVICE_ID_POS104UL 0x1044
#define PCI_DEVICE_ID_CB108 0x1080
#define PCI_DEVICE_ID_CP102UF 0x1023
+#define PCI_DEVICE_ID_CP112UL 0x1120
#define PCI_DEVICE_ID_CB114 0x1142
#define PCI_DEVICE_ID_CP114UL 0x1143
#define PCI_DEVICE_ID_CB134I 0x1341
{ "CP-138U series", 8, },
{ "POS-104UL series", 4, },
{ "CP-114UL series", 4, },
-/*30*/ { "CP-102UF series", 2, }
+/*30*/ { "CP-102UF series", 2, },
+ { "CP-112UL series", 2, },
};
/* driver_data correspond to the lines in the structure above
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 },
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 },
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 },
+ { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 },
{ }
};
MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
struct mxser_mon mon_data;
spinlock_t slock;
- wait_queue_head_t delta_msr_wait;
};
struct mxser_board {
return status;
}
-static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp,
- struct mxser_port *port)
+static int mxser_carrier_raised(struct tty_port *port)
{
- DECLARE_WAITQUEUE(wait, current);
- int retval;
- int do_clocal = 0;
- unsigned long flags;
-
- /*
- * If non-blocking mode is set, or the port is not enabled,
- * then make the check up front and then exit.
- */
- if ((filp->f_flags & O_NONBLOCK) ||
- test_bit(TTY_IO_ERROR, &tty->flags)) {
- port->port.flags |= ASYNC_NORMAL_ACTIVE;
- return 0;
- }
+ struct mxser_port *mp = container_of(port, struct mxser_port, port);
+ return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
+}
- if (tty->termios->c_cflag & CLOCAL)
- do_clocal = 1;
+static void mxser_dtr_rts(struct tty_port *port, int on)
+{
+ struct mxser_port *mp = container_of(port, struct mxser_port, port);
+ unsigned long flags;
- /*
- * Block waiting for the carrier detect and the line to become
- * free (i.e., not in use by the callout). While we are in
- * this loop, port->port.count is dropped by one, so that
- * mxser_close() knows when to free things. We restore it upon
- * exit, either normal or abnormal.
- */
- retval = 0;
- add_wait_queue(&port->port.open_wait, &wait);
-
- spin_lock_irqsave(&port->slock, flags);
- if (!tty_hung_up_p(filp))
- port->port.count--;
- spin_unlock_irqrestore(&port->slock, flags);
- port->port.blocked_open++;
- while (1) {
- spin_lock_irqsave(&port->slock, flags);
- outb(inb(port->ioaddr + UART_MCR) |
- UART_MCR_DTR | UART_MCR_RTS, port->ioaddr + UART_MCR);
- spin_unlock_irqrestore(&port->slock, flags);
- set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(port->port.flags & ASYNC_INITIALIZED)) {
- if (port->port.flags & ASYNC_HUP_NOTIFY)
- retval = -EAGAIN;
- else
- retval = -ERESTARTSYS;
- break;
- }
- if (!(port->port.flags & ASYNC_CLOSING) &&
- (do_clocal ||
- (inb(port->ioaddr + UART_MSR) & UART_MSR_DCD)))
- break;
- if (signal_pending(current)) {
- retval = -ERESTARTSYS;
- break;
- }
- schedule();
- }
- set_current_state(TASK_RUNNING);
- remove_wait_queue(&port->port.open_wait, &wait);
- if (!tty_hung_up_p(filp))
- port->port.count++;
- port->port.blocked_open--;
- if (retval)
- return retval;
- port->port.flags |= ASYNC_NORMAL_ACTIVE;
- return 0;
+ spin_lock_irqsave(&mp->slock, flags);
+ if (on)
+ outb(inb(mp->ioaddr + UART_MCR) |
+ UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR);
+ else
+ outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS),
+ mp->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&mp->slock, flags);
}
-static int mxser_set_baud(struct mxser_port *info, long newspd)
+static int mxser_set_baud(struct tty_struct *tty, long newspd)
{
+ struct mxser_port *info = tty->driver_data;
int quot = 0, baud;
unsigned char cval;
- if (!info->port.tty || !info->port.tty->termios)
- return -1;
-
- if (!(info->ioaddr))
+ if (!info->ioaddr)
return -1;
if (newspd > info->max_baud)
if (newspd == 134) {
quot = 2 * info->baud_base / 269;
- tty_encode_baud_rate(info->port.tty, 134, 134);
+ tty_encode_baud_rate(tty, 134, 134);
} else if (newspd) {
quot = info->baud_base / newspd;
if (quot == 0)
quot = 1;
baud = info->baud_base/quot;
- tty_encode_baud_rate(info->port.tty, baud, baud);
+ tty_encode_baud_rate(tty, baud, baud);
} else {
quot = 0;
}
outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
#ifdef BOTHER
- if (C_BAUD(info->port.tty) == BOTHER) {
+ if (C_BAUD(tty) == BOTHER) {
quot = info->baud_base % newspd;
quot *= 8;
if (quot % newspd > newspd / 2) {
* This routine is called to set the UART divisor registers to match
* the specified baud rate for a serial port.
*/
-static int mxser_change_speed(struct mxser_port *info,
- struct ktermios *old_termios)
+static int mxser_change_speed(struct tty_struct *tty,
+ struct ktermios *old_termios)
{
+ struct mxser_port *info = tty->driver_data;
unsigned cflag, cval, fcr;
int ret = 0;
unsigned char status;
- if (!info->port.tty || !info->port.tty->termios)
- return ret;
- cflag = info->port.tty->termios->c_cflag;
- if (!(info->ioaddr))
+ cflag = tty->termios->c_cflag;
+ if (!info->ioaddr)
return ret;
- if (mxser_set_baud_method[info->port.tty->index] == 0)
- mxser_set_baud(info, tty_get_baud_rate(info->port.tty));
+ if (mxser_set_baud_method[tty->index] == 0)
+ mxser_set_baud(tty, tty_get_baud_rate(tty));
/* byte size and parity */
switch (cflag & CSIZE) {
info->MCR |= UART_MCR_AFE;
} else {
status = inb(info->ioaddr + UART_MSR);
- if (info->port.tty->hw_stopped) {
+ if (tty->hw_stopped) {
if (status & UART_MSR_CTS) {
- info->port.tty->hw_stopped = 0;
+ tty->hw_stopped = 0;
if (info->type != PORT_16550A &&
!info->board->chip_flag) {
outb(info->IER & ~UART_IER_THRI,
outb(info->IER, info->ioaddr +
UART_IER);
}
- tty_wakeup(info->port.tty);
+ tty_wakeup(tty);
}
} else {
if (!(status & UART_MSR_CTS)) {
- info->port.tty->hw_stopped = 1;
+ tty->hw_stopped = 1;
if ((info->type != PORT_16550A) &&
(!info->board->chip_flag)) {
info->IER &= ~UART_IER_THRI;
* Set up parity check flag
*/
info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
- if (I_INPCK(info->port.tty))
+ if (I_INPCK(tty))
info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
- if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
+ if (I_BRKINT(tty) || I_PARMRK(tty))
info->read_status_mask |= UART_LSR_BI;
info->ignore_status_mask = 0;
- if (I_IGNBRK(info->port.tty)) {
+ if (I_IGNBRK(tty)) {
info->ignore_status_mask |= UART_LSR_BI;
info->read_status_mask |= UART_LSR_BI;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
- if (I_IGNPAR(info->port.tty)) {
+ if (I_IGNPAR(tty)) {
info->ignore_status_mask |=
UART_LSR_OE |
UART_LSR_PE |
}
}
if (info->board->chip_flag) {
- mxser_set_must_xon1_value(info->ioaddr, START_CHAR(info->port.tty));
- mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(info->port.tty));
- if (I_IXON(info->port.tty)) {
+ mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
+ mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
+ if (I_IXON(tty)) {
mxser_enable_must_rx_software_flow_control(
info->ioaddr);
} else {
mxser_disable_must_rx_software_flow_control(
info->ioaddr);
}
- if (I_IXOFF(info->port.tty)) {
+ if (I_IXOFF(tty)) {
mxser_enable_must_tx_software_flow_control(
info->ioaddr);
} else {
return ret;
}
-static void mxser_check_modem_status(struct mxser_port *port, int status)
+static void mxser_check_modem_status(struct tty_struct *tty,
+ struct mxser_port *port, int status)
{
/* update input line counters */
if (status & UART_MSR_TERI)
if (status & UART_MSR_DCTS)
port->icount.cts++;
port->mon_data.modem_status = status;
- wake_up_interruptible(&port->delta_msr_wait);
+ wake_up_interruptible(&port->port.delta_msr_wait);
if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
if (status & UART_MSR_DCD)
}
if (port->port.flags & ASYNC_CTS_FLOW) {
- if (port->port.tty->hw_stopped) {
+ if (tty->hw_stopped) {
if (status & UART_MSR_CTS) {
- port->port.tty->hw_stopped = 0;
+ tty->hw_stopped = 0;
if ((port->type != PORT_16550A) &&
(!port->board->chip_flag)) {
outb(port->IER, port->ioaddr +
UART_IER);
}
- tty_wakeup(port->port.tty);
+ tty_wakeup(tty);
}
} else {
if (!(status & UART_MSR_CTS)) {
- port->port.tty->hw_stopped = 1;
+ tty->hw_stopped = 1;
if (port->type != PORT_16550A &&
!port->board->chip_flag) {
port->IER &= ~UART_IER_THRI;
}
}
-static int mxser_startup(struct mxser_port *info)
+static int mxser_startup(struct tty_struct *tty)
{
+ struct mxser_port *info = tty->driver_data;
unsigned long page;
unsigned long flags;
}
if (!info->ioaddr || !info->type) {
- if (info->port.tty)
- set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ set_bit(TTY_IO_ERROR, &tty->flags);
free_page(page);
spin_unlock_irqrestore(&info->slock, flags);
return 0;
if (inb(info->ioaddr + UART_LSR) == 0xff) {
spin_unlock_irqrestore(&info->slock, flags);
if (capable(CAP_SYS_ADMIN)) {
- if (info->port.tty)
- set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ if (tty)
+ set_bit(TTY_IO_ERROR, &tty->flags);
return 0;
} else
return -ENODEV;
(void) inb(info->ioaddr + UART_IIR);
(void) inb(info->ioaddr + UART_MSR);
- if (info->port.tty)
- clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ clear_bit(TTY_IO_ERROR, &tty->flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
/*
* and set the speed of the serial port
*/
- mxser_change_speed(info, NULL);
+ mxser_change_speed(tty, NULL);
info->port.flags |= ASYNC_INITIALIZED;
spin_unlock_irqrestore(&info->slock, flags);
* This routine will shutdown a serial port; interrupts maybe disabled, and
* DTR is dropped if the hangup on close termio flag is on.
*/
-static void mxser_shutdown(struct mxser_port *info)
+static void mxser_shutdown(struct tty_struct *tty)
{
+ struct mxser_port *info = tty->driver_data;
unsigned long flags;
if (!(info->port.flags & ASYNC_INITIALIZED))
* clear delta_msr_wait queue to avoid mem leaks: we may free the irq
* here so the queue might never be waken up
*/
- wake_up_interruptible(&info->delta_msr_wait);
+ wake_up_interruptible(&info->port.delta_msr_wait);
/*
* Free the IRQ, if necessary
info->IER = 0;
outb(0x00, info->ioaddr + UART_IER);
- if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL))
+ if (tty->termios->c_cflag & HUPCL)
info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS);
outb(info->MCR, info->ioaddr + UART_MCR);
/* read data port to reset things */
(void) inb(info->ioaddr + UART_RX);
- if (info->port.tty)
- set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ set_bit(TTY_IO_ERROR, &tty->flags);
info->port.flags &= ~ASYNC_INITIALIZED;
return -ENODEV;
tty->driver_data = info;
- info->port.tty = tty;
+ tty_port_tty_set(&info->port, tty);
/*
* Start up serial port
*/
- spin_lock_irqsave(&info->slock, flags);
+ spin_lock_irqsave(&info->port.lock, flags);
info->port.count++;
- spin_unlock_irqrestore(&info->slock, flags);
- retval = mxser_startup(info);
+ spin_unlock_irqrestore(&info->port.lock, flags);
+ retval = mxser_startup(tty);
if (retval)
return retval;
- retval = mxser_block_til_ready(tty, filp, info);
+ retval = tty_port_block_til_ready(&info->port, tty, filp);
if (retval)
return retval;
- /* unmark here for very high baud rate (ex. 921600 bps) used */
- tty->low_latency = 1;
return 0;
}
}
-/*
- * This routine is called when the serial port gets closed. First, we
- * wait for the last remaining data to be sent. Then, we unlink its
- * async structure from the interrupt chain if necessary, and we free
- * that IRQ if nothing is left in the chain.
- */
-static void mxser_close(struct tty_struct *tty, struct file *filp)
+static void mxser_close_port(struct tty_struct *tty, struct tty_port *port)
{
- struct mxser_port *info = tty->driver_data;
-
+ struct mxser_port *info = container_of(port, struct mxser_port, port);
unsigned long timeout;
- unsigned long flags;
-
- if (tty->index == MXSER_PORTS)
- return;
- if (!info)
- return;
-
- spin_lock_irqsave(&info->slock, flags);
-
- if (tty_hung_up_p(filp)) {
- spin_unlock_irqrestore(&info->slock, flags);
- return;
- }
- if ((tty->count == 1) && (info->port.count != 1)) {
- /*
- * Uh, oh. tty->count is 1, which means that the tty
- * structure will be freed. Info->port.count should always
- * be one in these conditions. If it's greater than
- * one, we've got real problems, since it means the
- * serial port won't be shutdown.
- */
- printk(KERN_ERR "mxser_close: bad serial port count; "
- "tty->count is 1, info->port.count is %d\n", info->port.count);
- info->port.count = 1;
- }
- if (--info->port.count < 0) {
- printk(KERN_ERR "mxser_close: bad serial port count for "
- "ttys%d: %d\n", tty->index, info->port.count);
- info->port.count = 0;
- }
- if (info->port.count) {
- spin_unlock_irqrestore(&info->slock, flags);
- return;
- }
- info->port.flags |= ASYNC_CLOSING;
- spin_unlock_irqrestore(&info->slock, flags);
/*
* Save the termios structure, since this port may have
* separate termios for callout and dialin.
+ *
+ * FIXME: Can this go ?
*/
- if (info->port.flags & ASYNC_NORMAL_ACTIVE)
+ if (port->flags & ASYNC_NORMAL_ACTIVE)
info->normal_termios = *tty->termios;
/*
- * Now we wait for the transmit buffer to clear; and we notify
- * the line discipline to only process XON/XOFF characters.
- */
- tty->closing = 1;
- if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE)
- tty_wait_until_sent(tty, info->port.closing_wait);
- /*
* At this point we stop accepting input. To do this, we
* disable the receive line status interrupts, and tell the
* interrupt driver to stop checking the data ready bit in the
if (info->board->chip_flag)
info->IER &= ~MOXA_MUST_RECV_ISR;
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (port->flags & ASYNC_INITIALIZED) {
outb(info->IER, info->ioaddr + UART_IER);
/*
* Before we drop DTR, make sure the UART transmitter
break;
}
}
- mxser_shutdown(info);
+ mxser_shutdown(tty);
- mxser_flush_buffer(tty);
- tty_ldisc_flush(tty);
+}
- tty->closing = 0;
- info->port.tty = NULL;
- if (info->port.blocked_open) {
- if (info->port.close_delay)
- schedule_timeout_interruptible(info->port.close_delay);
- wake_up_interruptible(&info->port.open_wait);
- }
+/*
+ * This routine is called when the serial port gets closed. First, we
+ * wait for the last remaining data to be sent. Then, we unlink its
+ * async structure from the interrupt chain if necessary, and we free
+ * that IRQ if nothing is left in the chain.
+ */
+static void mxser_close(struct tty_struct *tty, struct file *filp)
+{
+ struct mxser_port *info = tty->driver_data;
+ struct tty_port *port = &info->port;
- info->port.flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING);
+ if (tty->index == MXSER_PORTS)
+ return;
+ if (tty_port_close_start(port, tty, filp) == 0)
+ return;
+ mxser_close_port(tty, port);
+ mxser_flush_buffer(tty);
+ /* Right now the tty_port set is done outside of the close_end helper
+ as we don't yet have everyone using refcounts */
+ tty_port_close_end(port, tty);
+ tty_port_tty_set(port, NULL);
}
static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
* friends of mxser_ioctl()
* ------------------------------------------------------------
*/
-static int mxser_get_serial_info(struct mxser_port *info,
+static int mxser_get_serial_info(struct tty_struct *tty,
struct serial_struct __user *retinfo)
{
+ struct mxser_port *info = tty->driver_data;
struct serial_struct tmp = {
.type = info->type,
- .line = info->port.tty->index,
+ .line = tty->index,
.port = info->ioaddr,
.irq = info->board->irq,
.flags = info->port.flags,
return 0;
}
-static int mxser_set_serial_info(struct mxser_port *info,
+static int mxser_set_serial_info(struct tty_struct *tty,
struct serial_struct __user *new_info)
{
+ struct mxser_port *info = tty->driver_data;
struct serial_struct new_serial;
speed_t baud;
unsigned long sl_flags;
(new_serial.flags & ASYNC_FLAGS));
info->port.close_delay = new_serial.close_delay * HZ / 100;
info->port.closing_wait = new_serial.closing_wait * HZ / 100;
- info->port.tty->low_latency =
- (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY)
+ ? 1 : 0;
if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
(new_serial.baud_base != info->baud_base ||
new_serial.custom_divisor !=
info->custom_divisor)) {
baud = new_serial.baud_base / new_serial.custom_divisor;
- tty_encode_baud_rate(info->port.tty, baud, baud);
+ tty_encode_baud_rate(tty, baud, baud);
}
}
if (info->port.flags & ASYNC_INITIALIZED) {
if (flags != (info->port.flags & ASYNC_SPD_MASK)) {
spin_lock_irqsave(&info->slock, sl_flags);
- mxser_change_speed(info, NULL);
+ mxser_change_speed(tty, NULL);
spin_unlock_irqrestore(&info->slock, sl_flags);
}
} else
- retval = mxser_startup(info);
+ retval = mxser_startup(tty);
return retval;
}
spin_lock_irqsave(&info->slock, flags);
status = inb(info->ioaddr + UART_MSR);
if (status & UART_MSR_ANY_DELTA)
- mxser_check_modem_status(info, status);
+ mxser_check_modem_status(tty, info, status);
spin_unlock_irqrestore(&info->slock, flags);
return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
{
struct mxser_port *port;
+ struct tty_struct *tty;
int result, status;
unsigned int i, j;
int ret = 0;
if (!port->ioaddr)
goto copy;
+
+ tty = tty_port_tty_get(&port->port);
- if (!port->port.tty || !port->port.tty->termios)
+ if (!tty || !tty->termios)
ms.cflag = port->normal_termios.c_cflag;
else
- ms.cflag = port->port.tty->termios->c_cflag;
-
+ ms.cflag = tty->termios->c_cflag;
+ tty_kref_put(tty);
status = inb(port->ioaddr + UART_MSR);
if (status & UART_MSR_DCD)
ms.dcd = 1;
me->up_txcnt[p] = port->mon_data.up_txcnt;
me->modem_status[p] =
port->mon_data.modem_status;
- me->baudrate[p] = tty_get_baud_rate(port->port.tty);
+ tty = tty_port_tty_get(&port->port);
- if (!port->port.tty || !port->port.tty->termios) {
+ if (!tty || !tty->termios) {
cflag = port->normal_termios.c_cflag;
iflag = port->normal_termios.c_iflag;
+ me->baudrate[p] = tty_termios_baud_rate(&port->normal_termios);
} else {
- cflag = port->port.tty->termios->c_cflag;
- iflag = port->port.tty->termios->c_iflag;
+ cflag = tty->termios->c_cflag;
+ iflag = tty->termios->c_iflag;
+ me->baudrate[p] = tty_get_baud_rate(tty);
}
+ tty_kref_put(tty);
me->databits[p] = cflag & CSIZE;
me->stopbits[p] = cflag & CSTOPB;
switch (cmd) {
case TIOCGSERIAL:
lock_kernel();
- retval = mxser_get_serial_info(info, argp);
+ retval = mxser_get_serial_info(tty, argp);
unlock_kernel();
return retval;
case TIOCSSERIAL:
lock_kernel();
- retval = mxser_set_serial_info(info, argp);
+ retval = mxser_set_serial_info(tty, argp);
unlock_kernel();
return retval;
case TIOCSERGETLSR: /* Get line status register */
cnow = info->icount; /* note the counters on entry */
spin_unlock_irqrestore(&info->slock, flags);
- return wait_event_interruptible(info->delta_msr_wait,
+ return wait_event_interruptible(info->port.delta_msr_wait,
mxser_cflags_changed(info, arg, &cnow));
/*
* Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
lock_kernel();
len = mxser_chars_in_buffer(tty);
- lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT;
+ lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE;
len += (lsr ? 0 : 1);
unlock_kernel();
lock_kernel();
status = mxser_get_msr(info->ioaddr, 1, tty->index);
- mxser_check_modem_status(info, status);
+ mxser_check_modem_status(tty, info, status);
mcr = inb(info->ioaddr + UART_MCR);
if (mcr & MOXA_MUST_MCR_XON_FLAG)
else
info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
- if (info->port.tty->hw_stopped)
+ if (tty->hw_stopped)
info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
else
info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
}
}
- if (info->port.tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios->c_cflag & CRTSCTS) {
info->MCR &= ~UART_MCR_RTS;
outb(info->MCR, info->ioaddr + UART_MCR);
}
}
}
- if (info->port.tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios->c_cflag & CRTSCTS) {
info->MCR |= UART_MCR_RTS;
outb(info->MCR, info->ioaddr + UART_MCR);
}
unsigned long flags;
spin_lock_irqsave(&info->slock, flags);
- mxser_change_speed(info, old_termios);
+ mxser_change_speed(tty, old_termios);
spin_unlock_irqrestore(&info->slock, flags);
if ((old_termios->c_cflag & CRTSCTS) &&
struct mxser_port *info = tty->driver_data;
mxser_flush_buffer(tty);
- mxser_shutdown(info);
- info->port.count = 0;
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
- info->port.tty = NULL;
- wake_up_interruptible(&info->port.open_wait);
+ mxser_shutdown(tty);
+ tty_port_hangup(&info->port);
}
/*
return 0;
}
-static void mxser_receive_chars(struct mxser_port *port, int *status)
+static void mxser_receive_chars(struct tty_struct *tty,
+ struct mxser_port *port, int *status)
{
- struct tty_struct *tty = port->port.tty;
unsigned char ch, gdl;
int ignored = 0;
int cnt = 0;
int max = 256;
recv_room = tty->receive_room;
- if ((recv_room == 0) && (!port->ldisc_stop_rx))
+ if (recv_room == 0 && !port->ldisc_stop_rx)
mxser_stoprx(tty);
-
if (port->board->chip_flag != MOXA_OTHER_UART) {
if (*status & UART_LSR_SPECIAL)
} while (*status & UART_LSR_DR);
end_intr:
- mxvar_log.rxcnt[port->port.tty->index] += cnt;
+ mxvar_log.rxcnt[tty->index] += cnt;
port->mon_data.rxcnt += cnt;
port->mon_data.up_rxcnt += cnt;
spin_lock(&port->slock);
}
-static void mxser_transmit_chars(struct mxser_port *port)
+static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
{
int count, cnt;
if (port->x_char) {
outb(port->x_char, port->ioaddr + UART_TX);
port->x_char = 0;
- mxvar_log.txcnt[port->port.tty->index]++;
+ mxvar_log.txcnt[tty->index]++;
port->mon_data.txcnt++;
port->mon_data.up_txcnt++;
port->icount.tx++;
if (port->port.xmit_buf == NULL)
return;
- if ((port->xmit_cnt <= 0) || port->port.tty->stopped ||
- (port->port.tty->hw_stopped &&
+ if (port->xmit_cnt <= 0 || tty->stopped ||
+ (tty->hw_stopped &&
(port->type != PORT_16550A) &&
(!port->board->chip_flag))) {
port->IER &= ~UART_IER_THRI;
if (--port->xmit_cnt <= 0)
break;
} while (--count > 0);
- mxvar_log.txcnt[port->port.tty->index] += (cnt - port->xmit_cnt);
+ mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt);
port->mon_data.txcnt += (cnt - port->xmit_cnt);
port->mon_data.up_txcnt += (cnt - port->xmit_cnt);
port->icount.tx += (cnt - port->xmit_cnt);
- if (port->xmit_cnt < WAKEUP_CHARS)
- tty_wakeup(port->port.tty);
+ if (port->xmit_cnt < WAKEUP_CHARS && tty)
+ tty_wakeup(tty);
if (port->xmit_cnt <= 0) {
port->IER &= ~UART_IER_THRI;
int max, irqbits, bits, msr;
unsigned int int_cnt, pass_counter = 0;
int handled = IRQ_NONE;
+ struct tty_struct *tty;
for (i = 0; i < MXSER_BOARDS; i++)
if (dev_id == &mxser_boards[i]) {
if (iir & UART_IIR_NO_INT)
break;
iir &= MOXA_MUST_IIR_MASK;
- if (!port->port.tty ||
+ tty = tty_port_tty_get(&port->port);
+ if (!tty ||
(port->port.flags & ASYNC_CLOSING) ||
!(port->port.flags &
ASYNC_INITIALIZED)) {
status = inb(port->ioaddr + UART_LSR);
outb(0x27, port->ioaddr + UART_FCR);
inb(port->ioaddr + UART_MSR);
+ tty_kref_put(tty);
break;
}
iir == MOXA_MUST_IIR_RDA ||
iir == MOXA_MUST_IIR_RTO ||
iir == MOXA_MUST_IIR_LSR)
- mxser_receive_chars(port,
+ mxser_receive_chars(tty, port,
&status);
} else {
status &= port->read_status_mask;
if (status & UART_LSR_DR)
- mxser_receive_chars(port,
+ mxser_receive_chars(tty, port,
&status);
}
msr = inb(port->ioaddr + UART_MSR);
if (msr & UART_MSR_ANY_DELTA)
- mxser_check_modem_status(port, msr);
+ mxser_check_modem_status(tty, port, msr);
if (port->board->chip_flag) {
if (iir == 0x02 && (status &
UART_LSR_THRE))
- mxser_transmit_chars(port);
+ mxser_transmit_chars(tty, port);
} else {
if (status & UART_LSR_THRE)
- mxser_transmit_chars(port);
+ mxser_transmit_chars(tty, port);
}
+ tty_kref_put(tty);
} while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
spin_unlock(&port->slock);
}
.tiocmset = mxser_tiocmset,
};
+struct tty_port_operations mxser_port_ops = {
+ .carrier_raised = mxser_carrier_raised,
+ .dtr_rts = mxser_dtr_rts,
+};
+
/*
* The MOXA Smartio/Industio serial driver boot-time initialization code!
*/
for (i = 0; i < brd->info->nports; i++) {
info = &brd->ports[i];
tty_port_init(&info->port);
+ info->port.ops = &mxser_port_ops;
info->board = brd;
info->stop_rx = 0;
info->ldisc_stop_rx = 0;
info->port.close_delay = 5 * HZ / 10;
info->port.closing_wait = 30 * HZ;
info->normal_termios = mxvar_sdriver->init_termios;
- init_waitqueue_head(&info->delta_msr_wait);
memset(&info->mon_data, 0, sizeof(struct mxser_mon));
info->err_shadow = 0;
spin_lock_init(&info->slock);
continue;
brd = &mxser_boards[m];
- retval = mxser_get_ISA_conf(!ioaddr[b], brd);
+ retval = mxser_get_ISA_conf(ioaddr[b], brd);
if (retval <= 0) {
brd->info = NULL;
continue;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff