#define NR_PORTS 256
-#define ZE_V1_NPORTS 64
#define ZO_V1 0
#define ZO_V2 1
#define ZE_V1 2
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial.h>
+#include <linux/smp_lock.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/fcntl.h>
#include <linux/spinlock.h>
#include <linux/bitops.h>
#include <linux/firmware.h>
+#include <linux/device.h>
#include <asm/system.h>
#include <linux/io.h>
#include <linux/stat.h>
#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
static void cy_throttle(struct tty_struct *tty);
static void cy_send_xchar(struct tty_struct *tty, char ch);
-#define IS_CYC_Z(card) ((card).num_chips == (unsigned int)-1)
-
-#define Z_FPGA_CHECK(card) \
- ((readl(&((struct RUNTIME_9060 __iomem *) \
- ((card).ctl_addr))->init_ctrl) & (1<<17)) != 0)
-
-#define ISZLOADED(card) (((ZO_V1 == readl(&((struct RUNTIME_9060 __iomem *) \
- ((card).ctl_addr))->mail_box_0)) || \
- Z_FPGA_CHECK(card)) && \
- (ZFIRM_ID == readl(&((struct FIRM_ID __iomem *) \
- ((card).base_addr+ID_ADDRESS))->signature)))
-
#ifndef SERIAL_XMIT_SIZE
#define SERIAL_XMIT_SIZE (min(PAGE_SIZE, 4096))
#endif
#define DRIVER_VERSION 0x02010203
#define RAM_SIZE 0x80000
-#define Z_FPGA_LOADED(X) ((readl(&(X)->init_ctrl) & (1<<17)) != 0)
-
enum zblock_type {
ZBLOCK_PRG = 0,
ZBLOCK_FPGA = 1
/*
* This is used to look up the divisor speeds and the timeouts
* We're normally limited to 15 distinct baud rates. The extra
- * are accessed via settings in info->flags.
+ * are accessed via settings in info->port.flags.
* 0, 1, 2, 3, 4, 5, 6, 7, 8, 9,
* 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
* HI VHI
static unsigned detect_isa_irq(void __iomem *);
#endif /* CONFIG_ISA */
-static int cyclades_get_proc_info(char *, char **, off_t, int, int *, void *);
-
#ifndef CONFIG_CYZ_INTR
static void cyz_poll(unsigned long);
static struct timer_list cyz_rx_full_timer[NR_PORTS];
#endif /* CONFIG_CYZ_INTR */
+static inline bool cy_is_Z(struct cyclades_card *card)
+{
+ return card->num_chips == (unsigned int)-1;
+}
+
+static inline bool __cyz_fpga_loaded(struct RUNTIME_9060 __iomem *ctl_addr)
+{
+ return readl(&ctl_addr->init_ctrl) & (1 << 17);
+}
+
+static inline bool cyz_fpga_loaded(struct cyclades_card *card)
+{
+ return __cyz_fpga_loaded(card->ctl_addr.p9060);
+}
+
+static inline bool cyz_is_loaded(struct cyclades_card *card)
+{
+ struct FIRM_ID __iomem *fw_id = card->base_addr + ID_ADDRESS;
+
+ return (card->hw_ver == ZO_V1 || cyz_fpga_loaded(card)) &&
+ readl(&fw_id->signature) == ZFIRM_ID;
+}
+
static inline int serial_paranoia_check(struct cyclades_port *info,
char *name, const char *routine)
{
cy_writeb(base_addr + (CyCAR << index), save_xir);
/* if there is nowhere to put the data, discard it */
- if (info->tty == NULL) {
+ if (info->port.tty == NULL) {
if ((readb(base_addr + (CyRIVR << index)) & CyIVRMask) ==
CyIVRRxEx) { /* exception */
data = readb(base_addr + (CyRDSR << index));
goto end;
}
/* there is an open port for this data */
- tty = info->tty;
+ tty = info->port.tty;
if ((readb(base_addr + (CyRIVR << index)) & CyIVRMask) ==
CyIVRRxEx) { /* exception */
data = readb(base_addr + (CyRDSR << index));
readb(base_addr + (CyRDSR <<
index)), TTY_BREAK);
info->icount.rx++;
- if (info->flags & ASYNC_SAK)
+ if (info->port.flags & ASYNC_SAK)
do_SAK(tty);
} else if (data & CyFRAME) {
tty_insert_flip_char(tty,
goto end;
}
info = &cinfo->ports[channel + chip * 4];
- if (info->tty == NULL) {
+ if (info->port.tty == NULL) {
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) & ~CyTxRdy);
goto end;
}
goto done;
}
- if (info->xmit_buf == NULL) {
+ if (info->port.xmit_buf == NULL) {
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) &
~CyTxRdy);
goto done;
}
- if (info->tty->stopped || info->tty->hw_stopped) {
+ if (info->port.tty->stopped || info->port.tty->hw_stopped) {
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) &
~CyTxRdy);
* character. This is necessary because there may not be room
* for the two chars needed to send a NULL.)
*/
- outch = info->xmit_buf[info->xmit_tail];
+ outch = info->port.xmit_buf[info->xmit_tail];
if (outch) {
info->xmit_cnt--;
info->xmit_tail = (info->xmit_tail + 1) &
}
done:
- tty_wakeup(info->tty);
+ tty_wakeup(info->port.tty);
end:
/* end of service */
cy_writeb(base_addr + (CyTIR << index), save_xir & 0x3f);
mdm_change = readb(base_addr + (CyMISR << index));
mdm_status = readb(base_addr + (CyMSVR1 << index));
- if (!info->tty)
+ if (!info->port.tty)
goto end;
if (mdm_change & CyANY_DELTA) {
wake_up_interruptible(&info->delta_msr_wait);
}
- if ((mdm_change & CyDCD) && (info->flags & ASYNC_CHECK_CD)) {
+ if ((mdm_change & CyDCD) && (info->port.flags & ASYNC_CHECK_CD)) {
if (!(mdm_status & CyDCD)) {
- tty_hangup(info->tty);
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_hangup(info->port.tty);
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
}
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
}
- if ((mdm_change & CyCTS) && (info->flags & ASYNC_CTS_FLOW)) {
- if (info->tty->hw_stopped) {
+ if ((mdm_change & CyCTS) && (info->port.flags & ASYNC_CTS_FLOW)) {
+ if (info->port.tty->hw_stopped) {
if (mdm_status & CyCTS) {
/* cy_start isn't used
because... !!! */
- info->tty->hw_stopped = 0;
+ info->port.tty->hw_stopped = 0;
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) |
CyTxRdy);
- tty_wakeup(info->tty);
+ tty_wakeup(info->port.tty);
}
} else {
if (!(mdm_status & CyCTS)) {
/* cy_stop isn't used
because ... !!! */
- info->tty->hw_stopped = 1;
+ info->port.tty->hw_stopped = 1;
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) &
~CyTxRdy);
unsigned long loc_doorbell;
firm_id = cinfo->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo))
- return -1;
zfw_ctrl = cinfo->base_addr + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
- loc_doorbell = readl(&((struct RUNTIME_9060 __iomem *)
- (cinfo->ctl_addr))->loc_doorbell);
+ loc_doorbell = readl(&cinfo->ctl_addr.p9060->loc_doorbell);
if (loc_doorbell) {
*cmd = (char)(0xff & loc_doorbell);
*channel = readl(&board_ctrl->fwcmd_channel);
*param = (__u32) readl(&board_ctrl->fwcmd_param);
- cy_writel(&((struct RUNTIME_9060 __iomem *)(cinfo->ctl_addr))->
- loc_doorbell, 0xffffffff);
+ cy_writel(&cinfo->ctl_addr.p9060->loc_doorbell, 0xffffffff);
return 1;
}
return 0;
unsigned int index;
firm_id = cinfo->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo))
+ if (!cyz_is_loaded(cinfo))
return -1;
zfw_ctrl = cinfo->base_addr + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
index = 0;
- pci_doorbell =
- &((struct RUNTIME_9060 __iomem *)(cinfo->ctl_addr))->pci_doorbell;
+ pci_doorbell = &cinfo->ctl_addr.p9060->pci_doorbell;
while ((readl(pci_doorbell) & 0xff) != 0) {
if (index++ == 1000)
return (int)(readl(pci_doorbell) & 0xff);
struct BUF_CTRL __iomem *buf_ctrl)
{
struct cyclades_card *cinfo = info->card;
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
unsigned int char_count;
int len;
#ifdef BLOCKMOVE
struct BUF_CTRL __iomem *buf_ctrl)
{
struct cyclades_card *cinfo = info->card;
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
u8 data;
unsigned int char_count;
#ifdef BLOCKMOVE
memcpy_toio((char *)(cinfo->base_addr + tx_bufaddr +
tx_put),
- &info->xmit_buf[info->xmit_tail],
+ &info->port.xmit_buf[info->xmit_tail],
small_count);
tx_put = (tx_put + small_count) & (tx_bufsize - 1);
}
#else
while (info->xmit_cnt && char_count) {
- data = info->xmit_buf[info->xmit_tail];
+ data = info->port.xmit_buf[info->xmit_tail];
info->xmit_cnt--;
info->xmit_tail = (info->xmit_tail + 1) &
(SERIAL_XMIT_SIZE - 1);
static struct BOARD_CTRL __iomem *board_ctrl;
static struct CH_CTRL __iomem *ch_ctrl;
static struct BUF_CTRL __iomem *buf_ctrl;
- __u32 channel;
+ __u32 channel, param, fw_ver;
__u8 cmd;
- __u32 param;
- __u32 hw_ver, fw_ver;
int special_count;
int delta_count;
zfw_ctrl = cinfo->base_addr + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
fw_ver = readl(&board_ctrl->fw_version);
- hw_ver = readl(&((struct RUNTIME_9060 __iomem *)(cinfo->ctl_addr))->
- mail_box_0);
while (cyz_fetch_msg(cinfo, &channel, &cmd, ¶m) == 1) {
special_count = 0;
delta_count = 0;
info = &cinfo->ports[channel];
- tty = info->tty;
+ tty = info->port.tty;
if (tty == NULL)
continue;
case C_CM_MDCD:
info->icount.dcd++;
delta_count++;
- if (info->flags & ASYNC_CHECK_CD) {
+ if (info->port.flags & ASYNC_CHECK_CD) {
if ((fw_ver > 241 ? ((u_long) param) :
readl(&ch_ctrl->rs_status)) &
C_RS_DCD) {
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
} else {
- tty_hangup(info->tty);
- wake_up_interruptible(&info->open_wait);
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_hangup(info->port.tty);
+ wake_up_interruptible(&info->port.open_wait);
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
}
}
break;
{
struct cyclades_card *cinfo = dev_id;
- if (unlikely(cinfo == NULL)) {
-#ifdef CY_DEBUG_INTERRUPTS
- printk(KERN_DEBUG "cyz_interrupt: spurious interrupt %d\n",
- irq);
-#endif
- return IRQ_NONE; /* spurious interrupt */
- }
-
- if (unlikely(!ISZLOADED(*cinfo))) {
+ if (unlikely(!cyz_is_loaded(cinfo))) {
#ifdef CY_DEBUG_INTERRUPTS
printk(KERN_DEBUG "cyz_interrupt: board not yet loaded "
"(IRQ%d).\n", irq);
struct tty_struct *tty;
struct FIRM_ID __iomem *firm_id;
struct ZFW_CTRL __iomem *zfw_ctrl;
- struct BOARD_CTRL __iomem *board_ctrl;
struct BUF_CTRL __iomem *buf_ctrl;
unsigned long expires = jiffies + HZ;
unsigned int port, card;
for (card = 0; card < NR_CARDS; card++) {
cinfo = &cy_card[card];
- if (!IS_CYC_Z(*cinfo))
+ if (!cy_is_Z(cinfo))
continue;
- if (!ISZLOADED(*cinfo))
+ if (!cyz_is_loaded(cinfo))
continue;
firm_id = cinfo->base_addr + ID_ADDRESS;
zfw_ctrl = cinfo->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
- board_ctrl = &(zfw_ctrl->board_ctrl);
/* Skip first polling cycle to avoid racing conditions with the FW */
if (!cinfo->intr_enabled) {
- cinfo->nports = (int)readl(&board_ctrl->n_channel);
cinfo->intr_enabled = 1;
continue;
}
for (port = 0; port < cinfo->nports; port++) {
info = &cinfo->ports[port];
- tty = info->tty;
+ tty = info->port.tty;
buf_ctrl = &(zfw_ctrl->buf_ctrl[port]);
if (!info->throttle)
spin_lock_irqsave(&card->card_lock, flags);
- if (info->flags & ASYNC_INITIALIZED) {
+ if (info->port.flags & ASYNC_INITIALIZED) {
free_page(page);
goto errout;
}
if (!info->type) {
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);
free_page(page);
goto errout;
}
- if (info->xmit_buf)
+ if (info->port.xmit_buf)
free_page(page);
else
- info->xmit_buf = (unsigned char *)page;
+ info->port.xmit_buf = (unsigned char *)page;
spin_unlock_irqrestore(&card->card_lock, flags);
set_line_char(info);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) | CyRxData);
- info->flags |= ASYNC_INITIALIZED;
+ info->port.flags |= ASYNC_INITIALIZED;
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
info->breakon = info->breakoff = 0;
memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
base_addr = card->base_addr;
firm_id = base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card))
+ if (!cyz_is_loaded(card))
return -ENODEV;
zfw_ctrl = card->base_addr +
/* enable send, recv, modem !!! */
- info->flags |= ASYNC_INITIALIZED;
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ info->port.flags |= ASYNC_INITIALIZED;
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
info->breakon = info->breakoff = 0;
memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
void __iomem *base_addr;
int chip, channel, index;
- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
return;
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
/* Clear delta_msr_wait queue to avoid mem leaks. */
wake_up_interruptible(&info->delta_msr_wait);
- if (info->xmit_buf) {
+ if (info->port.xmit_buf) {
unsigned char *temp;
- temp = info->xmit_buf;
- info->xmit_buf = NULL;
+ temp = info->port.xmit_buf;
+ info->port.xmit_buf = NULL;
free_page((unsigned long)temp);
}
cy_writeb(base_addr + (CyCAR << index), (u_char) channel);
- if (!info->tty || (info->tty->termios->c_cflag & HUPCL)) {
+ if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
cy_writeb(base_addr + (CyMSVR1 << index), ~CyRTS);
cy_writeb(base_addr + (CyMSVR2 << index), ~CyDTR);
#ifdef CY_DEBUG_DTR
/* it may be appropriate to clear _XMIT at
some later date (after testing)!!! */
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
- info->flags &= ~ASYNC_INITIALIZED;
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ info->port.flags &= ~ASYNC_INITIALIZED;
spin_unlock_irqrestore(&card->card_lock, flags);
} else {
struct FIRM_ID __iomem *firm_id;
#endif
firm_id = base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card))
+ if (!cyz_is_loaded(card))
return;
zfw_ctrl = card->base_addr +
spin_lock_irqsave(&card->card_lock, flags);
- if (info->xmit_buf) {
+ if (info->port.xmit_buf) {
unsigned char *temp;
- temp = info->xmit_buf;
- info->xmit_buf = NULL;
+ temp = info->port.xmit_buf;
+ info->port.xmit_buf = NULL;
free_page((unsigned long)temp);
}
- if (!info->tty || (info->tty->termios->c_cflag & HUPCL)) {
+ if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
cy_writel(&ch_ctrl[channel].rs_control,
(__u32)(readl(&ch_ctrl[channel].rs_control) &
~(C_RS_RTS | C_RS_DTR)));
#endif
}
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
- info->flags &= ~ASYNC_INITIALIZED;
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+ info->port.flags &= ~ASYNC_INITIALIZED;
spin_unlock_irqrestore(&card->card_lock, flags);
}
* If the device is in the middle of being closed, then block
* until it's done, and then try again.
*/
- if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) {
- wait_event_interruptible(info->close_wait,
- !(info->flags & ASYNC_CLOSING));
- return (info->flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
+ if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) {
+ wait_event_interruptible(info->port.close_wait,
+ !(info->port.flags & ASYNC_CLOSING));
+ return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
}
/*
*/
if ((filp->f_flags & O_NONBLOCK) ||
(tty->flags & (1 << TTY_IO_ERROR))) {
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ info->port.flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
/*
* Block waiting for the carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
- * this loop, info->count is dropped by one, so that
+ * this loop, info->port.count is dropped by one, so that
* cy_close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
- add_wait_queue(&info->open_wait, &wait);
+ add_wait_queue(&info->port.open_wait, &wait);
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc block_til_ready before block: ttyC%d, "
- "count = %d\n", info->line, info->count);
+ "count = %d\n", info->line, info->port.count);
#endif
spin_lock_irqsave(&cinfo->card_lock, flags);
if (!tty_hung_up_p(filp))
- info->count--;
+ info->port.count--;
spin_unlock_irqrestore(&cinfo->card_lock, flags);
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc block_til_ready: (%d): decrementing count to "
- "%d\n", current->pid, info->count);
+ "%d\n", current->pid, info->port.count);
#endif
- info->blocked_open++;
+ info->port.blocked_open++;
- if (!IS_CYC_Z(*cinfo)) {
+ if (!cy_is_Z(cinfo)) {
chip = channel >> 2;
channel &= 0x03;
index = cinfo->bus_index;
set_current_state(TASK_INTERRUPTIBLE);
if (tty_hung_up_p(filp) ||
- !(info->flags & ASYNC_INITIALIZED)) {
- retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
+ !(info->port.flags & ASYNC_INITIALIZED)) {
+ retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS);
break;
}
spin_lock_irqsave(&cinfo->card_lock, flags);
cy_writeb(base_addr + (CyCAR << index),
(u_char) channel);
- if (!(info->flags & ASYNC_CLOSING) && (C_CLOCAL(tty) ||
+ if (!(info->port.flags & ASYNC_CLOSING) && (C_CLOCAL(tty) ||
(readb(base_addr +
(CyMSVR1 << index)) & CyDCD))) {
spin_unlock_irqrestore(&cinfo->card_lock, flags);
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc block_til_ready blocking: "
"ttyC%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
schedule();
}
base_addr = cinfo->base_addr;
firm_id = base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo)) {
+ if (!cyz_is_loaded(cinfo)) {
__set_current_state(TASK_RUNNING);
- remove_wait_queue(&info->open_wait, &wait);
+ remove_wait_queue(&info->port.open_wait, &wait);
return -EINVAL;
}
set_current_state(TASK_INTERRUPTIBLE);
if (tty_hung_up_p(filp) ||
- !(info->flags & ASYNC_INITIALIZED)) {
- retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
+ !(info->port.flags & ASYNC_INITIALIZED)) {
+ retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS);
break;
}
- if (!(info->flags & ASYNC_CLOSING) && (C_CLOCAL(tty) ||
+ if (!(info->port.flags & ASYNC_CLOSING) && (C_CLOCAL(tty) ||
(readl(&ch_ctrl[channel].rs_status) &
C_RS_DCD))) {
break;
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc block_til_ready blocking: "
"ttyC%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
schedule();
}
}
__set_current_state(TASK_RUNNING);
- remove_wait_queue(&info->open_wait, &wait);
+ remove_wait_queue(&info->port.open_wait, &wait);
if (!tty_hung_up_p(filp)) {
- info->count++;
+ info->port.count++;
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc:block_til_ready (%d): incrementing "
- "count to %d\n", current->pid, info->count);
+ "count to %d\n", current->pid, info->port.count);
#endif
}
- info->blocked_open--;
+ info->port.blocked_open--;
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc:block_til_ready after blocking: ttyC%d, "
- "count = %d\n", info->line, info->count);
+ "count = %d\n", info->line, info->port.count);
#endif
if (retval)
return retval;
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ info->port.flags |= ASYNC_NORMAL_ACTIVE;
return 0;
} /* block_til_ready */
treat it as absent from the system. This
will make the user pay attention.
*/
- if (IS_CYC_Z(*info->card)) {
+ if (cy_is_Z(info->card)) {
struct cyclades_card *cinfo = info->card;
struct FIRM_ID __iomem *firm_id = cinfo->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*cinfo)) {
- if (((ZE_V1 == readl(&((struct RUNTIME_9060 __iomem *)
- (cinfo->ctl_addr))->mail_box_0)) &&
- Z_FPGA_CHECK(*cinfo)) &&
- (ZFIRM_HLT == readl(
- &firm_id->signature))) {
+ if (!cyz_is_loaded(cinfo)) {
+ if (cinfo->hw_ver == ZE_V1 && cyz_fpga_loaded(cinfo) &&
+ readl(&firm_id->signature) ==
+ ZFIRM_HLT) {
printk(KERN_ERR "cyc:Cyclades-Z Error: you "
"need an external power supply for "
"this number of ports.\nFirmware "
interrupts should be enabled as soon as the first open
happens to one of its ports. */
if (!cinfo->intr_enabled) {
- struct ZFW_CTRL __iomem *zfw_ctrl;
- struct BOARD_CTRL __iomem *board_ctrl;
-
- zfw_ctrl = cinfo->base_addr +
- (readl(&firm_id->zfwctrl_addr) &
- 0xfffff);
-
- board_ctrl = &zfw_ctrl->board_ctrl;
+ u16 intr;
/* Enable interrupts on the PLX chip */
- cy_writew(cinfo->ctl_addr + 0x68,
- readw(cinfo->ctl_addr + 0x68) | 0x0900);
+ intr = readw(&cinfo->ctl_addr.p9060->
+ intr_ctrl_stat) | 0x0900;
+ cy_writew(&cinfo->ctl_addr.p9060->
+ intr_ctrl_stat, intr);
/* Enable interrupts on the FW */
retval = cyz_issue_cmd(cinfo, 0,
C_CM_IRQ_ENBL, 0L);
printk(KERN_ERR "cyc:IRQ enable retval "
"was %x\n", retval);
}
- cinfo->nports =
- (int)readl(&board_ctrl->n_channel);
cinfo->intr_enabled = 1;
}
}
printk(KERN_DEBUG "cyc:cy_open ttyC%d\n", info->line);
#endif
tty->driver_data = info;
- info->tty = tty;
+ info->port.tty = tty;
if (serial_paranoia_check(info, tty->name, "cy_open"))
return -ENODEV;
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc:cy_open ttyC%d, count = %d\n", info->line,
- info->count);
+ info->port.count);
#endif
- info->count++;
+ info->port.count++;
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc:cy_open (%d): incrementing count to %d\n",
- current->pid, info->count);
+ current->pid, info->port.count);
#endif
/*
* If the port is the middle of closing, bail out now
*/
- if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) {
- wait_event_interruptible(info->close_wait,
- !(info->flags & ASYNC_CLOSING));
- return (info->flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
+ if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) {
+ wait_event_interruptible(info->port.close_wait,
+ !(info->port.flags & ASYNC_CLOSING));
+ return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
}
/*
#endif
card = info->card;
channel = (info->line) - (card->first_line);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
spin_unlock_irqrestore(&card->card_lock, flags);
- if (IS_CYC_Z(*card)) { /* If it is a Z card, flush the on-board
+ if (cy_is_Z(card)) { /* If it is a Z card, flush the on-board
buffers as well */
spin_lock_irqsave(&card->card_lock, flags);
retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_TX, 0L);
}
#ifdef CY_DEBUG_OPEN
printk(KERN_DEBUG "cyc:cy_close ttyC%d, count = %d\n", info->line,
- info->count);
+ info->port.count);
#endif
- if ((tty->count == 1) && (info->count != 1)) {
+ if ((tty->count == 1) && (info->port.count != 1)) {
/*
* Uh, oh. tty->count is 1, which means that the tty
* structure will be freed. Info->count should always
* serial port won't be shutdown.
*/
printk(KERN_ERR "cyc:cy_close: bad serial port count; "
- "tty->count is 1, info->count is %d\n", info->count);
- info->count = 1;
+ "tty->count is 1, info->port.count is %d\n", info->port.count);
+ info->port.count = 1;
}
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc:cy_close at (%d): decrementing count to %d\n",
- current->pid, info->count - 1);
+ current->pid, info->port.count - 1);
#endif
- if (--info->count < 0) {
+ if (--info->port.count < 0) {
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc:cyc_close setting count to 0\n");
#endif
- info->count = 0;
+ info->port.count = 0;
}
- if (info->count) {
+ if (info->port.count) {
spin_unlock_irqrestore(&card->card_lock, flags);
return;
}
- info->flags |= ASYNC_CLOSING;
+ info->port.flags |= ASYNC_CLOSING;
/*
* Now we wait for the transmit buffer to clear; and we notify
*/
tty->closing = 1;
spin_unlock_irqrestore(&card->card_lock, flags);
- if (info->closing_wait != CY_CLOSING_WAIT_NONE)
- tty_wait_until_sent(tty, info->closing_wait);
+ if (info->port.closing_wait != CY_CLOSING_WAIT_NONE)
+ tty_wait_until_sent(tty, info->port.closing_wait);
spin_lock_irqsave(&card->card_lock, flags);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
int channel = info->line - card->first_line;
int index = card->bus_index;
void __iomem *base_addr = card->base_addr +
cy_writeb(base_addr + (CyCAR << index), (u_char) channel);
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) & ~CyRxData);
- if (info->flags & ASYNC_INITIALIZED) {
+ if (info->port.flags & ASYNC_INITIALIZED) {
/* Waiting for on-board buffers to be empty before
closing the port */
spin_unlock_irqrestore(&card->card_lock, flags);
spin_lock_irqsave(&card->card_lock, flags);
tty->closing = 0;
- info->tty = NULL;
- if (info->blocked_open) {
+ info->port.tty = NULL;
+ if (info->port.blocked_open) {
spin_unlock_irqrestore(&card->card_lock, flags);
- if (info->close_delay) {
+ if (info->port.close_delay) {
msleep_interruptible(jiffies_to_msecs
- (info->close_delay));
+ (info->port.close_delay));
}
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
spin_lock_irqsave(&card->card_lock, flags);
}
- info->flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING);
- wake_up_interruptible(&info->close_wait);
+ info->port.flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING);
+ wake_up_interruptible(&info->port.close_wait);
#ifdef CY_DEBUG_OTHER
printk(KERN_DEBUG "cyc:cy_close done\n");
if (serial_paranoia_check(info, tty->name, "cy_write"))
return 0;
- if (!info->xmit_buf)
+ if (!info->port.xmit_buf)
return 0;
spin_lock_irqsave(&info->card->card_lock, flags);
if (c <= 0)
break;
- memcpy(info->xmit_buf + info->xmit_head, buf, c);
+ memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
info->xmit_head = (info->xmit_head + c) &
(SERIAL_XMIT_SIZE - 1);
info->xmit_cnt += c;
if (serial_paranoia_check(info, tty->name, "cy_put_char"))
return 0;
- if (!info->xmit_buf)
+ if (!info->port.xmit_buf)
return 0;
spin_lock_irqsave(&info->card->card_lock, flags);
return 0;
}
- info->xmit_buf[info->xmit_head++] = ch;
+ info->port.xmit_buf[info->xmit_head++] = ch;
info->xmit_head &= SERIAL_XMIT_SIZE - 1;
info->xmit_cnt++;
info->idle_stats.xmit_bytes++;
return;
if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
- !info->xmit_buf)
+ !info->port.xmit_buf)
return;
start_xmit(info);
channel = (info->line) - (card->first_line);
#ifdef Z_EXT_CHARS_IN_BUFFER
- if (!IS_CYC_Z(cy_card[card])) {
+ if (!cy_is_Z(card)) {
#endif /* Z_EXT_CHARS_IN_BUFFER */
#ifdef CY_DEBUG_IO
printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
void __iomem *base_addr;
int chip, channel, index;
unsigned cflag, iflag;
- unsigned short chip_number;
int baud, baud_rate = 0;
int i;
- if (!info->tty || !info->tty->termios)
+ if (!info->port.tty || !info->port.tty->termios)
return;
if (info->line == -1)
return;
- cflag = info->tty->termios->c_cflag;
- iflag = info->tty->termios->c_iflag;
+ cflag = info->port.tty->termios->c_cflag;
+ iflag = info->port.tty->termios->c_iflag;
/*
* Set up the tty->alt_speed kludge
*/
- if (info->tty) {
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
- info->tty->alt_speed = 57600;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
- info->tty->alt_speed = 115200;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
- info->tty->alt_speed = 230400;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
- info->tty->alt_speed = 460800;
+ if (info->port.tty) {
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+ info->port.tty->alt_speed = 57600;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+ info->port.tty->alt_speed = 115200;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+ info->port.tty->alt_speed = 230400;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+ info->port.tty->alt_speed = 460800;
}
card = info->card;
channel = info->line - card->first_line;
- chip_number = channel / 4;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
index = card->bus_index;
/* baud rate */
- baud = tty_get_baud_rate(info->tty);
- if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
+ baud = tty_get_baud_rate(info->port.tty);
+ if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
if (info->custom_divisor)
baud_rate = info->baud / info->custom_divisor;
if (i == 20)
i = 19; /* CD1400_MAX_SPEED */
- if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
+ if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
cyy_baud_calc(info, baud_rate);
} else {
/* get it right for 134.5 baud */
info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
2;
- } else if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
+ } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
info->timeout = (info->xmit_fifo_size * HZ * 15 /
baud_rate) + 2;
/* CTS flow control flag */
if (cflag & CRTSCTS) {
- info->flags |= ASYNC_CTS_FLOW;
+ info->port.flags |= ASYNC_CTS_FLOW;
info->cor2 |= CyCtsAE;
} else {
- info->flags &= ~ASYNC_CTS_FLOW;
+ info->port.flags &= ~ASYNC_CTS_FLOW;
info->cor2 &= ~CyCtsAE;
}
if (cflag & CLOCAL)
- info->flags &= ~ASYNC_CHECK_CD;
+ info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->flags |= ASYNC_CHECK_CD;
+ info->port.flags |= ASYNC_CHECK_CD;
/***********************************************
The hardware option, CyRtsAO, presents RTS when
/* set line characteristics according configuration */
cy_writeb(base_addr + (CySCHR1 << index),
- START_CHAR(info->tty));
- cy_writeb(base_addr + (CySCHR2 << index), STOP_CHAR(info->tty));
+ START_CHAR(info->port.tty));
+ cy_writeb(base_addr + (CySCHR2 << index), STOP_CHAR(info->port.tty));
cy_writeb(base_addr + (CyCOR1 << index), info->cor1);
cy_writeb(base_addr + (CyCOR2 << index), info->cor2);
cy_writeb(base_addr + (CyCOR3 << index), info->cor3);
(info->default_timeout ? info->default_timeout : 0x02));
/* 10ms rx timeout */
- if (C_CLOCAL(info->tty)) {
+ if (C_CLOCAL(info->port.tty)) {
/* without modem intr */
cy_writeb(base_addr + (CySRER << index),
readb(base_addr + (CySRER << index)) | CyMdmCh);
#endif
}
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
spin_unlock_irqrestore(&card->card_lock, flags);
} else {
struct FIRM_ID __iomem *firm_id;
struct ZFW_CTRL __iomem *zfw_ctrl;
- struct BOARD_CTRL __iomem *board_ctrl;
struct CH_CTRL __iomem *ch_ctrl;
- struct BUF_CTRL __iomem *buf_ctrl;
__u32 sw_flow;
int retval;
firm_id = card->base_addr + ID_ADDRESS;
- if (!ISZLOADED(*card))
+ if (!cyz_is_loaded(card))
return;
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
- board_ctrl = &zfw_ctrl->board_ctrl;
ch_ctrl = &(zfw_ctrl->ch_ctrl[channel]);
- buf_ctrl = &zfw_ctrl->buf_ctrl[channel];
/* baud rate */
- baud = tty_get_baud_rate(info->tty);
- if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
+ baud = tty_get_baud_rate(info->port.tty);
+ if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
if (info->custom_divisor)
baud_rate = info->baud / info->custom_divisor;
/* get it right for 134.5 baud */
info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
2;
- } else if (baud == 38400 && (info->flags & ASYNC_SPD_MASK) ==
+ } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
ASYNC_SPD_CUST) {
info->timeout = (info->xmit_fifo_size * HZ * 15 /
baud_rate) + 2;
}
/* As the HW flow control is done in firmware, the driver
doesn't need to care about it */
- info->flags &= ~ASYNC_CTS_FLOW;
+ info->port.flags &= ~ASYNC_CTS_FLOW;
/* XON/XOFF/XANY flow control flags */
sw_flow = 0;
/* CD sensitivity */
if (cflag & CLOCAL)
- info->flags &= ~ASYNC_CHECK_CD;
+ info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->flags |= ASYNC_CHECK_CD;
+ info->port.flags |= ASYNC_CHECK_CD;
if (baud == 0) { /* baud rate is zero, turn off line */
cy_writel(&ch_ctrl->rs_control,
"was %x\n", info->line, retval);
}
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
}
} /* set_line_char */
tmp.port = (info->card - cy_card) * 0x100 + info->line -
cinfo->first_line;
tmp.irq = cinfo->irq;
- tmp.flags = info->flags;
- tmp.close_delay = info->close_delay;
- tmp.closing_wait = info->closing_wait;
+ tmp.flags = info->port.flags;
+ tmp.close_delay = info->port.close_delay;
+ tmp.closing_wait = info->port.closing_wait;
tmp.baud_base = info->baud;
tmp.custom_divisor = info->custom_divisor;
tmp.hub6 = 0; /*!!! */
old_info = *info;
if (!capable(CAP_SYS_ADMIN)) {
- if (new_serial.close_delay != info->close_delay ||
+ if (new_serial.close_delay != info->port.close_delay ||
new_serial.baud_base != info->baud ||
(new_serial.flags & ASYNC_FLAGS &
~ASYNC_USR_MASK) !=
- (info->flags & ASYNC_FLAGS & ~ASYNC_USR_MASK))
+ (info->port.flags & ASYNC_FLAGS & ~ASYNC_USR_MASK))
return -EPERM;
- info->flags = (info->flags & ~ASYNC_USR_MASK) |
+ info->port.flags = (info->port.flags & ~ASYNC_USR_MASK) |
(new_serial.flags & ASYNC_USR_MASK);
info->baud = new_serial.baud_base;
info->custom_divisor = new_serial.custom_divisor;
info->baud = new_serial.baud_base;
info->custom_divisor = new_serial.custom_divisor;
- info->flags = (info->flags & ~ASYNC_FLAGS) |
+ info->port.flags = (info->port.flags & ~ASYNC_FLAGS) |
(new_serial.flags & ASYNC_FLAGS);
- info->close_delay = new_serial.close_delay * HZ / 100;
- info->closing_wait = new_serial.closing_wait * HZ / 100;
+ info->port.close_delay = new_serial.close_delay * HZ / 100;
+ info->port.closing_wait = new_serial.closing_wait * HZ / 100;
check_and_exit:
- if (info->flags & ASYNC_INITIALIZED) {
+ if (info->port.flags & ASYNC_INITIALIZED) {
set_line_char(info);
return 0;
} else {
card = info->card;
channel = (info->line) - (card->first_line);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
} else {
base_addr = card->base_addr;
firm_id = card->base_addr + ID_ADDRESS;
- if (ISZLOADED(*card)) {
+ if (cyz_is_loaded(card)) {
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
card = info->card;
channel = (info->line) - (card->first_line);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
base_addr = card->base_addr;
firm_id = card->base_addr + ID_ADDRESS;
- if (ISZLOADED(*card)) {
+ if (cyz_is_loaded(card)) {
zfw_ctrl = card->base_addr +
(readl(&firm_id->zfwctrl_addr) & 0xfffff);
board_ctrl = &zfw_ctrl->board_ctrl;
/*
* cy_break() --- routine which turns the break handling on or off
*/
-static void cy_break(struct tty_struct *tty, int break_state)
+static int cy_break(struct tty_struct *tty, int break_state)
{
struct cyclades_port *info = tty->driver_data;
struct cyclades_card *card;
unsigned long flags;
+ int retval = 0;
if (serial_paranoia_check(info, tty->name, "cy_break"))
- return;
+ return -EINVAL;
card = info->card;
spin_lock_irqsave(&card->card_lock, flags);
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
/* Let the transmit ISR take care of this (since it
requires stuffing characters into the output stream).
*/
}
}
} else {
- int retval;
-
if (break_state == -1) {
retval = cyz_issue_cmd(card,
info->line - card->first_line,
}
}
spin_unlock_irqrestore(&card->card_lock, flags);
+ return retval;
} /* cy_break */
static int get_mon_info(struct cyclades_port *info,
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
break;
#endif /* CONFIG_CYZ_INTR */
case CYSETWAIT:
- info->closing_wait = (unsigned short)arg * HZ / 100;
+ info->port.closing_wait = (unsigned short)arg * HZ / 100;
ret_val = 0;
break;
case CYGETWAIT:
- ret_val = info->closing_wait / (HZ / 100);
+ ret_val = info->port.closing_wait / (HZ / 100);
break;
case TIOCGSERIAL:
ret_val = get_serial_info(info, argp);
*/
if (!(old_termios->c_cflag & CLOCAL) &&
(tty->termios->c_cflag & CLOCAL))
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
#endif
} /* cy_set_termios */
card = info->card;
channel = info->line - card->first_line;
- if (IS_CYC_Z(*card)) {
+ if (cy_is_Z(card)) {
if (ch == STOP_CHAR(tty))
cyz_issue_cmd(card, channel, C_CM_SENDXOFF, 0L);
else if (ch == START_CHAR(tty))
card = info->card;
if (I_IXOFF(tty)) {
- if (!IS_CYC_Z(*card))
+ if (!cy_is_Z(card))
cy_send_xchar(tty, STOP_CHAR(tty));
else
info->throttle = 1;
if (tty->termios->c_cflag & CRTSCTS) {
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
if (tty->termios->c_cflag & CRTSCTS) {
card = info->card;
channel = info->line - card->first_line;
- if (!IS_CYC_Z(*card)) {
+ if (!cy_is_Z(card)) {
chip = channel >> 2;
channel &= 0x03;
index = card->bus_index;
cinfo = info->card;
channel = info->line - cinfo->first_line;
- if (!IS_CYC_Z(*cinfo)) {
+ if (!cy_is_Z(cinfo)) {
index = cinfo->bus_index;
chip = channel >> 2;
channel &= 0x03;
cinfo = info->card;
channel = info->line - cinfo->first_line;
index = cinfo->bus_index;
- if (!IS_CYC_Z(*cinfo)) {
+ if (!cy_is_Z(cinfo)) {
chip = channel >> 2;
channel &= 0x03;
base_addr = cinfo->base_addr + (cy_chip_offset[chip] << index);
cy_flush_buffer(tty);
shutdown(info);
- info->count = 0;
+ info->port.count = 0;
#ifdef CY_DEBUG_COUNT
printk(KERN_DEBUG "cyc:cy_hangup (%d): setting count to 0\n",
current->pid);
#endif
- info->tty = NULL;
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
- wake_up_interruptible(&info->open_wait);
+ info->port.tty = NULL;
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ wake_up_interruptible(&info->port.open_wait);
} /* cy_hangup */
/*
static int __devinit cy_init_card(struct cyclades_card *cinfo)
{
struct cyclades_port *info;
- u32 uninitialized_var(mailbox);
- unsigned int nports, port;
+ unsigned int port;
unsigned short chip_number;
- int uninitialized_var(index);
spin_lock_init(&cinfo->card_lock);
+ cinfo->intr_enabled = 0;
- if (IS_CYC_Z(*cinfo)) { /* Cyclades-Z */
- mailbox = readl(&((struct RUNTIME_9060 __iomem *)
- cinfo->ctl_addr)->mail_box_0);
- nports = (mailbox == ZE_V1) ? ZE_V1_NPORTS : 8;
- cinfo->intr_enabled = 0;
- cinfo->nports = 0; /* Will be correctly set later, after
- Z FW is loaded */
- } else {
- index = cinfo->bus_index;
- nports = cinfo->nports = CyPORTS_PER_CHIP * cinfo->num_chips;
- }
-
- cinfo->ports = kzalloc(sizeof(*cinfo->ports) * nports, GFP_KERNEL);
+ cinfo->ports = kcalloc(cinfo->nports, sizeof(*cinfo->ports),
+ GFP_KERNEL);
if (cinfo->ports == NULL) {
printk(KERN_ERR "Cyclades: cannot allocate ports\n");
- cinfo->nports = 0;
return -ENOMEM;
}
- for (port = cinfo->first_line; port < cinfo->first_line + nports;
+ for (port = cinfo->first_line; port < cinfo->first_line + cinfo->nports;
port++) {
info = &cinfo->ports[port - cinfo->first_line];
+ tty_port_init(&info->port);
info->magic = CYCLADES_MAGIC;
info->card = cinfo;
info->line = port;
- info->flags = STD_COM_FLAGS;
- info->closing_wait = CLOSING_WAIT_DELAY;
- info->close_delay = 5 * HZ / 10;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
+ info->port.closing_wait = CLOSING_WAIT_DELAY;
+ info->port.close_delay = 5 * HZ / 10;
+ info->port.flags = STD_COM_FLAGS;
init_completion(&info->shutdown_wait);
init_waitqueue_head(&info->delta_msr_wait);
- if (IS_CYC_Z(*cinfo)) {
+ if (cy_is_Z(cinfo)) {
info->type = PORT_STARTECH;
- if (mailbox == ZO_V1)
+ if (cinfo->hw_ver == ZO_V1)
info->xmit_fifo_size = CYZ_FIFO_SIZE;
else
info->xmit_fifo_size = 4 * CYZ_FIFO_SIZE;
cyz_rx_restart, (unsigned long)info);
#endif
} else {
+ int index = cinfo->bus_index;
info->type = PORT_CIRRUS;
info->xmit_fifo_size = CyMAX_CHAR_FIFO;
info->cor1 = CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS;
}
#ifndef CONFIG_CYZ_INTR
- if (IS_CYC_Z(*cinfo) && !timer_pending(&cyz_timerlist)) {
+ if (cy_is_Z(cinfo) && !timer_pending(&cyz_timerlist)) {
mod_timer(&cyz_timerlist, jiffies + 1);
#ifdef CY_PCI_DEBUG
printk(KERN_DEBUG "Cyclades-Z polling initialized\n");
/* set cy_card */
cy_card[j].base_addr = cy_isa_address;
- cy_card[j].ctl_addr = NULL;
+ cy_card[j].ctl_addr.p9050 = NULL;
cy_card[j].irq = (int)cy_isa_irq;
cy_card[j].bus_index = 0;
cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = cy_isa_nchan / 4;
+ cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
+ cy_card[j].nports = cy_isa_nchan;
if (cy_init_card(&cy_card[j])) {
cy_card[j].base_addr = NULL;
free_irq(cy_isa_irq, &cy_card[j]);
struct CUSTOM_REG __iomem *cust = base_addr;
struct ZFW_CTRL __iomem *pt_zfwctrl;
void __iomem *tmp;
- u32 mailbox, status;
+ u32 mailbox, status, nchan;
unsigned int i;
int retval;
/* Check whether the firmware is already loaded and running. If
positive, skip this board */
- if (Z_FPGA_LOADED(ctl_addr) && readl(&fid->signature) == ZFIRM_ID) {
+ if (__cyz_fpga_loaded(ctl_addr) && readl(&fid->signature) == ZFIRM_ID) {
u32 cntval = readl(base_addr + 0x190);
udelay(100);
mailbox = readl(&ctl_addr->mail_box_0);
- if (mailbox == 0 || Z_FPGA_LOADED(ctl_addr)) {
+ if (mailbox == 0 || __cyz_fpga_loaded(ctl_addr)) {
/* stops CPU and set window to beginning of RAM */
cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
cy_writel(&cust->cpu_stop, 0);
base_addr);
if (retval)
goto err_rel;
- if (!Z_FPGA_LOADED(ctl_addr)) {
+ if (!__cyz_fpga_loaded(ctl_addr)) {
dev_err(&pdev->dev, "fw upload successful, but fw is "
"not loaded\n");
goto err_rel;
"system before loading the new FW to the "
"Cyclades-Z.\n");
- if (Z_FPGA_LOADED(ctl_addr))
+ if (__cyz_fpga_loaded(ctl_addr))
plx_init(pdev, irq, ctl_addr);
retval = -EIO;
base_addr + ID_ADDRESS, readl(&fid->zfwctrl_addr),
base_addr + readl(&fid->zfwctrl_addr));
+ nchan = readl(&pt_zfwctrl->board_ctrl.n_channel);
dev_info(&pdev->dev, "Cyclades-Z FW loaded: version = %x, ports = %u\n",
- readl(&pt_zfwctrl->board_ctrl.fw_version),
- readl(&pt_zfwctrl->board_ctrl.n_channel));
+ readl(&pt_zfwctrl->board_ctrl.fw_version), nchan);
- if (readl(&pt_zfwctrl->board_ctrl.n_channel) == 0) {
+ if (nchan == 0) {
dev_warn(&pdev->dev, "no Cyclades-Z ports were found. Please "
"check the connection between the Z host card and the "
"serial expanders.\n");
- if (Z_FPGA_LOADED(ctl_addr))
+ if (__cyz_fpga_loaded(ctl_addr))
plx_init(pdev, irq, ctl_addr);
dev_info(&pdev->dev, "Null number of ports detected. Board "
cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) |
0x00030800UL);
- plx_init(pdev, irq, ctl_addr);
-
- return 0;
+ return nchan;
err_rel:
release_firmware(fw);
err:
{
void __iomem *addr0 = NULL, *addr2 = NULL;
char *card_name = NULL;
- u32 mailbox;
+ u32 uninitialized_var(mailbox);
unsigned int device_id, nchan = 0, card_no, i;
unsigned char plx_ver;
int retval, irq;
device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
card_name = "Cyclom-Y";
- addr0 = pci_iomap(pdev, 0, CyPCI_Yctl);
+ addr0 = ioremap_nocache(pci_resource_start(pdev, 0),
+ CyPCI_Yctl);
if (addr0 == NULL) {
dev_err(&pdev->dev, "can't remap ctl region\n");
goto err_reg;
}
- addr2 = pci_iomap(pdev, 2, CyPCI_Ywin);
+ addr2 = ioremap_nocache(pci_resource_start(pdev, 2),
+ CyPCI_Ywin);
if (addr2 == NULL) {
dev_err(&pdev->dev, "can't remap base region\n");
goto err_unmap;
if (nchan == 0) {
dev_err(&pdev->dev, "Cyclom-Y PCI host card with no "
"Serial-Modules\n");
- return -EIO;
+ goto err_unmap;
}
} else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
struct RUNTIME_9060 __iomem *ctl_addr;
- ctl_addr = addr0 = pci_iomap(pdev, 0, CyPCI_Zctl);
+ ctl_addr = addr0 = ioremap_nocache(pci_resource_start(pdev, 0),
+ CyPCI_Zctl);
if (addr0 == NULL) {
dev_err(&pdev->dev, "can't remap ctl region\n");
goto err_reg;
}
/* Disable interrupts on the PLX before resetting it */
- cy_writew(addr0 + 0x68, readw(addr0 + 0x68) & ~0x0900);
+ cy_writew(&ctl_addr->intr_ctrl_stat,
+ readw(&ctl_addr->intr_ctrl_stat) & ~0x0900);
plx_init(pdev, irq, addr0);
- mailbox = (u32)readl(&ctl_addr->mail_box_0);
+ mailbox = readl(&ctl_addr->mail_box_0);
- addr2 = pci_iomap(pdev, 2, mailbox == ZE_V1 ?
- CyPCI_Ze_win : CyPCI_Zwin);
+ addr2 = ioremap_nocache(pci_resource_start(pdev, 2),
+ mailbox == ZE_V1 ? CyPCI_Ze_win : CyPCI_Zwin);
if (addr2 == NULL) {
dev_err(&pdev->dev, "can't remap base region\n");
goto err_unmap;
if (mailbox == ZE_V1) {
card_name = "Cyclades-Ze";
-
- readl(&ctl_addr->mail_box_0);
- nchan = ZE_V1_NPORTS;
} else {
card_name = "Cyclades-8Zo";
-
#ifdef CY_PCI_DEBUG
if (mailbox == ZO_V1) {
cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
*/
if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
cy_writel(addr2 + ID_ADDRESS, 0L);
-
- retval = cyz_load_fw(pdev, addr2, addr0, irq);
- if (retval)
- goto err_unmap;
- /* This must be a Cyclades-8Zo/PCI. The extendable
- version will have a different device_id and will
- be allocated its maximum number of ports. */
- nchan = 8;
}
+
+ retval = cyz_load_fw(pdev, addr2, addr0, irq);
+ if (retval <= 0)
+ goto err_unmap;
+ nchan = retval;
}
if ((cy_next_channel + nchan) > NR_PORTS) {
dev_err(&pdev->dev, "could not allocate IRQ\n");
goto err_unmap;
}
- cy_card[card_no].num_chips = nchan / 4;
+ cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP;
} else {
+ cy_card[card_no].hw_ver = mailbox;
+ cy_card[card_no].num_chips = (unsigned int)-1;
#ifdef CONFIG_CYZ_INTR
/* allocate IRQ only if board has an IRQ */
if (irq != 0 && irq != 255) {
}
}
#endif /* CONFIG_CYZ_INTR */
- cy_card[card_no].num_chips = (unsigned int)-1;
}
/* set cy_card */
cy_card[card_no].base_addr = addr2;
- cy_card[card_no].ctl_addr = addr0;
+ cy_card[card_no].ctl_addr.p9050 = addr0;
cy_card[card_no].irq = irq;
cy_card[card_no].bus_index = 1;
cy_card[card_no].first_line = cy_next_channel;
+ cy_card[card_no].nports = nchan;
retval = cy_init_card(&cy_card[card_no]);
if (retval)
goto err_null;
plx_ver = readb(addr2 + CyPLX_VER) & 0x0f;
switch (plx_ver) {
case PLX_9050:
-
cy_writeb(addr0 + 0x4c, 0x43);
break;
case PLX_9060:
case PLX_9080:
default: /* Old boards, use PLX_9060 */
- plx_init(pdev, irq, addr0);
- cy_writew(addr0 + 0x68, readw(addr0 + 0x68) | 0x0900);
+ {
+ struct RUNTIME_9060 __iomem *ctl_addr = addr0;
+ plx_init(pdev, irq, ctl_addr);
+ cy_writew(&ctl_addr->intr_ctrl_stat,
+ readw(&ctl_addr->intr_ctrl_stat) | 0x0900);
break;
}
+ }
}
dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from "
cy_card[card_no].base_addr = NULL;
free_irq(irq, &cy_card[card_no]);
err_unmap:
- pci_iounmap(pdev, addr0);
+ iounmap(addr0);
if (addr2)
- pci_iounmap(pdev, addr2);
+ iounmap(addr2);
err_reg:
pci_release_regions(pdev);
err_dis:
unsigned int i;
/* non-Z with old PLX */
- if (!IS_CYC_Z(*cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) ==
+ if (!cy_is_Z(cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) ==
PLX_9050)
- cy_writeb(cinfo->ctl_addr + 0x4c, 0);
+ cy_writeb(cinfo->ctl_addr.p9050 + 0x4c, 0);
else
#ifndef CONFIG_CYZ_INTR
- if (!IS_CYC_Z(*cinfo))
+ if (!cy_is_Z(cinfo))
#endif
- cy_writew(cinfo->ctl_addr + 0x68,
- readw(cinfo->ctl_addr + 0x68) & ~0x0900);
+ cy_writew(&cinfo->ctl_addr.p9060->intr_ctrl_stat,
+ readw(&cinfo->ctl_addr.p9060->intr_ctrl_stat) &
+ ~0x0900);
- pci_iounmap(pdev, cinfo->base_addr);
- if (cinfo->ctl_addr)
- pci_iounmap(pdev, cinfo->ctl_addr);
+ iounmap(cinfo->base_addr);
+ if (cinfo->ctl_addr.p9050)
+ iounmap(cinfo->ctl_addr.p9050);
if (cinfo->irq
#ifndef CONFIG_CYZ_INTR
- && !IS_CYC_Z(*cinfo)
+ && !cy_is_Z(cinfo)
#endif /* CONFIG_CYZ_INTR */
)
free_irq(cinfo->irq, cinfo);
};
#endif
-static int
-cyclades_get_proc_info(char *buf, char **start, off_t offset, int length,
- int *eof, void *data)
+static int cyclades_proc_show(struct seq_file *m, void *v)
{
struct cyclades_port *info;
unsigned int i, j;
- int len = 0;
- off_t begin = 0;
- off_t pos = 0;
- int size;
__u32 cur_jifs = jiffies;
- size = sprintf(buf, "Dev TimeOpen BytesOut IdleOut BytesIn "
+ seq_puts(m, "Dev TimeOpen BytesOut IdleOut BytesIn "
"IdleIn Overruns Ldisc\n");
- pos += size;
- len += size;
-
/* Output one line for each known port */
for (i = 0; i < NR_CARDS; i++)
for (j = 0; j < cy_card[i].nports; j++) {
info = &cy_card[i].ports[j];
- if (info->count)
- size = sprintf(buf + len, "%3d %8lu %10lu %8lu "
+ if (info->port.count)
+ seq_printf(m, "%3d %8lu %10lu %8lu "
"%10lu %8lu %9lu %6ld\n", info->line,
(cur_jifs - info->idle_stats.in_use) /
HZ, info->idle_stats.xmit_bytes,
HZ, info->idle_stats.recv_bytes,
(cur_jifs - info->idle_stats.recv_idle)/
HZ, info->idle_stats.overruns,
- (long)info->tty->ldisc.num);
+ /* FIXME: double check locking */
+ (long)info->port.tty->ldisc->ops->num);
else
- size = sprintf(buf + len, "%3d %8lu %10lu %8lu "
+ seq_printf(m, "%3d %8lu %10lu %8lu "
"%10lu %8lu %9lu %6ld\n",
info->line, 0L, 0L, 0L, 0L, 0L, 0L, 0L);
- len += size;
- pos = begin + len;
-
- if (pos < offset) {
- len = 0;
- begin = pos;
- }
- if (pos > offset + length)
- goto done;
}
- *eof = 1;
-done:
- *start = buf + (offset - begin); /* Start of wanted data */
- len -= (offset - begin); /* Start slop */
- if (len > length)
- len = length; /* Ending slop */
- if (len < 0)
- len = 0;
- return len;
+ return 0;
+}
+
+static int cyclades_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, cyclades_proc_show, NULL);
}
+static const struct file_operations cyclades_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = cyclades_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
/* The serial driver boot-time initialization code!
Hardware I/O ports are mapped to character special devices on a
first found, first allocated manner. That is, this code searches
.hangup = cy_hangup,
.break_ctl = cy_break,
.wait_until_sent = cy_wait_until_sent,
- .read_proc = cyclades_get_proc_info,
.tiocmget = cy_tiocmget,
.tiocmset = cy_tiocmset,
+ .proc_fops = &cyclades_proc_fops,
};
static int __init cy_init(void)
/* clear interrupt */
cy_writeb(card->base_addr + Cy_ClrIntr, 0);
iounmap(card->base_addr);
- if (card->ctl_addr)
- iounmap(card->ctl_addr);
+ if (card->ctl_addr.p9050)
+ iounmap(card->ctl_addr.p9050);
if (card->irq
#ifndef CONFIG_CYZ_INTR
- && !IS_CYC_Z(*card)
+ && !cy_is_Z(card)
#endif /* CONFIG_CYZ_INTR */
)
free_irq(card->irq, card);
MODULE_LICENSE("GPL");
MODULE_VERSION(CY_VERSION);
+MODULE_ALIAS_CHARDEV_MAJOR(CYCLADES_MAJOR);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff