[PATCH] Char: sx, convert to pci probing

[safe/jmp/linux-2.6] / drivers / char / Kconfig

diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
index 0e6f35f..b10f4d8 100644 (file)
--- a/drivers/char/Kconfig
+++ b/drivers/char/Kconfig
@@ -201,6 +201,21 @@ config MOXA_SMARTIO
          The module will be called mxser. If you want to do that, say M
          here.
 
+config MOXA_SMARTIO_NEW
+       tristate "Moxa SmartIO support v. 2.0 (EXPERIMENTAL)"
+       depends on SERIAL_NONSTANDARD
+       help
+         Say Y here if you have a Moxa SmartIO multiport serial card and/or
+         want to help develop a new version of this driver.
+
+         This is upgraded (1.9.1) driver from original Moxa drivers with
+         changes finally resulting in PCI probing.
+
+         Use at your own risk.
+
+         This driver can also be built as a module. The module will be called
+         mxser_new. If you want to do that, say M here.
+
 config ISI
        tristate "Multi-Tech multiport card support (EXPERIMENTAL)"
        depends on SERIAL_NONSTANDARD
@@ -409,14 +424,6 @@ config SGI_MBCS
          If you have an SGI Altix with an attached SABrick
          say Y or M here, otherwise say N.
 
-config MSPEC
-       tristate "Memory special operations driver"
-       depends on IA64
-       help
-         If you have an ia64 and you want to enable memory special
-         operations support (formerly known as fetchop), say Y here,
-         otherwise say N.
-
 source "drivers/serial/Kconfig"
 
 config UNIX98_PTYS
@@ -863,39 +870,6 @@ config TANBAC_TB0219
        depends TANBAC_TB022X
        select GPIO_VR41XX
 
-menu "Ftape, the floppy tape device driver"
-
-config FTAPE
-       tristate "Ftape (QIC-80/Travan) support"
-       depends on BROKEN_ON_SMP && (ALPHA || X86)
-       ---help---
-         If you have a tape drive that is connected to your floppy
-         controller, say Y here.
-
-         Some tape drives (like the Seagate "Tape Store 3200" or the Iomega
-         "Ditto 3200" or the Exabyte "Eagle TR-3") come with a "high speed"
-         controller of their own. These drives (and their companion
-         controllers) are also supported if you say Y here.
-
-         If you have a special controller (such as the CMS FC-10, FC-20,
-         Mountain Mach-II, or any controller that is based on the Intel 82078
-         FDC like the high speed controllers by Seagate and Exabyte and
-         Iomega's "Ditto Dash") you must configure it by selecting the
-         appropriate entries from the "Floppy tape controllers" sub-menu
-         below and possibly modify the default values for the IRQ and DMA
-         channel and the IO base in ftape's configuration menu.
-
-         If you want to use your floppy tape drive on a PCI-bus based system,
-         please read the file <file:drivers/char/ftape/README.PCI>.
-
-         The ftape kernel driver is also available as a runtime loadable
-         module. To compile this driver as a module, choose M here: the
-         module will be called ftape.
-
-source "drivers/char/ftape/Kconfig"
-
-endmenu
-
 source "drivers/char/agp/Kconfig"
 
 source "drivers/char/drm/Kconfig"
@@ -1002,7 +976,7 @@ config HPET
        help
          If you say Y here, you will have a miscdevice named "/dev/hpet/".  Each
          open selects one of the timers supported by the HPET.  The timers are
-         non-periodioc and/or periodic.
+         non-periodic and/or periodic.
 
 config HPET_RTC_IRQ
        bool "HPET Control RTC IRQ" if !HPET_EMULATE_RTC
@@ -1046,7 +1020,7 @@ source "drivers/char/tpm/Kconfig"
 
 config TELCLOCK
        tristate "Telecom clock driver for MPBL0010 ATCA SBC"
-       depends on EXPERIMENTAL
+       depends on EXPERIMENTAL && X86
        default n
        help
          The telecom clock device is specific to the MPBL0010 ATCA computer and