---help---
If you want to use the floppy disk drive(s) of your PC under Linux,
say Y. Information about this driver, especially important for IBM
- Thinkpad users, is contained in <file:Documentation/floppy.txt>.
+ Thinkpad users, is contained in
+ <file:Documentation/blockdev/floppy.txt>.
That file also contains the location of the Floppy driver FAQ as
well as location of the fdutils package used to configure additional
parameters of the driver at run time.
If you have a SWIM-3 (Super Woz Integrated Machine 3; from Apple)
floppy controller, say Y here. Most commonly found in PowerMacs.
-config BLK_DEV_PS2
- tristate "PS/2 ESDI hard disk support"
- depends on MCA && MCA_LEGACY && BROKEN
- help
- Say Y here if you have a PS/2 machine with a MCA bus and an ESDI
- hard disk.
-
- To compile this driver as a module, choose M here: the
- module will be called ps2esdi.
-
config AMIGA_Z2RAM
tristate "Amiga Zorro II ramdisk support"
depends on ZORRO
your computer's parallel port. Most of them are actually IDE devices
using a parallel port IDE adapter. This option enables the PARIDE
subsystem which contains drivers for many of these external drives.
- Read <file:Documentation/paride.txt> for more information.
+ Read <file:Documentation/blockdev/paride.txt> for more information.
If you have said Y to the "Parallel-port support" configuration
option, you may share a single port between your printer and other
"MicroSolutions backpack protocol", "DataStor Commuter protocol"
etc.).
+config GDROM
+ tristate "SEGA Dreamcast GD-ROM drive"
+ depends on SH_DREAMCAST
+ help
+ A standard SEGA Dreamcast comes with a modified CD ROM drive called a
+ "GD-ROM" by SEGA to signify it is capable of reading special disks
+ with up to 1 GB of data. This drive will also read standard CD ROM
+ disks. Select this option to access any disks in your GD ROM drive.
+ Most users will want to say "Y" here.
+ You can also build this as a module which will be called gdrom.ko
+
source "drivers/block/paride/Kconfig"
config BLK_CPQ_DA
help
This is the driver for Compaq Smart Array controllers. Everyone
using these boards should say Y here. See the file
- <file:Documentation/cpqarray.txt> for the current list of boards
- supported by this driver, and for further information on the use of
- this driver.
+ <file:Documentation/blockdev/cpqarray.txt> for the current list of
+ boards supported by this driver, and for further information on the
+ use of this driver.
config BLK_CPQ_CISS_DA
tristate "Compaq Smart Array 5xxx support"
help
This is the driver for Compaq Smart Array 5xxx controllers.
Everyone using these boards should say Y here.
- See <file:Documentation/cciss.txt> for the current list of
+ See <file:Documentation/blockdev/cciss.txt> for the current list of
boards supported by this driver, and for further information
on the use of this driver.
help
When enabled (Y), this option allows SCSI tape drives and SCSI medium
changers (tape robots) to be accessed via a Compaq 5xxx array
- controller. (See <file:Documentation/cciss.txt> for more details.)
+ controller. (See <file:Documentation/blockdev/cciss.txt> for more details.)
"SCSI support" and "SCSI tape support" must also be enabled for this
option to work.
help
This driver adds support for the Mylex DAC960, AcceleRAID, and
eXtremeRAID PCI RAID controllers. See the file
- <file:Documentation/README.DAC960> for further information about
- this driver.
+ <file:Documentation/blockdev/README.DAC960> for further information
+ about this driver.
To compile this driver as a module, choose M here: the
module will be called DAC960.
userland (making server and client physically the same computer,
communicating using the loopback network device).
- Read <file:Documentation/nbd.txt> for more information, especially
- about where to find the server code, which runs in user space and
- does not need special kernel support.
+ Read <file:Documentation/blockdev/nbd.txt> for more information,
+ especially about where to find the server code, which runs in user
+ space and does not need special kernel support.
Note that this has nothing to do with the network file systems NFS
or Coda; you can say N here even if you intend to use NFS or Coda.
If unsure, say N.
config BLK_DEV_RAM
- tristate "RAM disk support"
+ tristate "RAM block device support"
---help---
Saying Y here will allow you to use a portion of your RAM memory as
a block device, so that you can make file systems on it, read and
store a copy of a minimal root file system off of a floppy into RAM
during the initial install of Linux.
- Note that the kernel command line option "ramdisk=XX" is now
- obsolete. For details, read <file:Documentation/ramdisk.txt>.
+ Note that the kernel command line option "ramdisk=XX" is now obsolete.
+ For details, read <file:Documentation/blockdev/ramdisk.txt>.
To compile this driver as a module, choose M here: the
module will be called rd.
The default value is 4096 kilobytes. Only change this if you know
what you are doing.
-config BLK_DEV_RAM_BLOCKSIZE
- int "Default RAM disk block size (bytes)"
+config BLK_DEV_XIP
+ bool "Support XIP filesystems on RAM block device"
depends on BLK_DEV_RAM
- default "1024"
+ default n
help
- The default value is 1024 bytes. PAGE_SIZE is a much more
- efficient choice however. The default is kept to ensure initrd
- setups function - apparently needed by the rd_load_image routine
- that supposes the filesystem in the image uses a 1024 blocksize.
+ Support XIP filesystems (such as ext2 with XIP support on) on
+ top of block ram device. This will slightly enlarge the kernel, and
+ will prevent RAM block device backing store memory from being
+ allocated from highmem (only a problem for highmem systems).
config CDROM_PKTCDVD
tristate "Packet writing on CD/DVD media"
tristate "Virtio block driver (EXPERIMENTAL)"
depends on EXPERIMENTAL && VIRTIO
---help---
- This is the virtual block driver for lguest. Say Y or M.
+ This is the virtual block driver for virtio. It can be used with
+ lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+
+config BLK_DEV_HD
+ bool "Very old hard disk (MFM/RLL/IDE) driver"
+ depends on HAVE_IDE
+ depends on !ARM || ARCH_RPC || ARCH_SHARK || BROKEN
+ help
+ This is a very old hard disk driver that lacks the enhanced
+ functionality of the newer ones.
+
+ It is required for systems with ancient MFM/RLL/ESDI drives.
+
+ If unsure, say N.
endif # BLK_DEV