#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.20"
+#define DRV_VERSION "1.24"
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
- /* SoC integrated controllers, no PCI interface */
- MV_FLAG_SOC = (1 << 28),
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
MV_GENIIE_FLAGS = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ ATA_FLAG_NCQ | ATA_FLAG_AN,
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */
HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
- HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
- PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
- HC_MAIN_RSVD),
- HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- HC_MAIN_RSVD_5),
- HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC),
/* SATAHC registers */
HC_CFG_OFS = 0,
SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
SATA_ACTIVE_OFS = 0x350,
SATA_FIS_IRQ_CAUSE_OFS = 0x364,
+ SATA_FIS_IRQ_AN = (1 << 9), /* async notification */
LTMODE_OFS = 0x30c,
LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */
PHY_MODE3 = 0x310,
PHY_MODE4 = 0x314,
+ PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */
+ PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */
+ PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */
+ PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */
+
PHY_MODE2 = 0x330,
SATA_IFCTL_OFS = 0x344,
SATA_TESTCTL_OFS = 0x348,
MV_HP_ERRATA_50XXB2 = (1 << 2),
MV_HP_ERRATA_60X1B2 = (1 << 3),
MV_HP_ERRATA_60X1C0 = (1 << 4),
- MV_HP_ERRATA_XX42A0 = (1 << 5),
MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */
MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */
MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
+ MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE)
-#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
+#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC)
#define WINDOW_CTRL(i) (0x20030 + ((i) << 4))
#define WINDOW_BASE(i) (0x20034 + ((i) << 4))
struct mv_host_priv {
u32 hp_flags;
+ u32 main_irq_mask;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
int n_ports;
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_GENIIE_FLAGS | MV_FLAG_SOC,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crqb_dma & 0xffffffff) | index,
- port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+ writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
/*
* initialize response queue
WARN_ON(pp->crpb_dma & 0xff);
writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crpb_dma & 0xffffffff) | index,
- port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
-
+ writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_set_main_irq_mask(struct ata_host *host,
+ u32 disable_bits, u32 enable_bits)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ u32 old_mask, new_mask;
+
+ old_mask = hpriv->main_irq_mask;
+ new_mask = (old_mask & ~disable_bits) | enable_bits;
+ if (new_mask != old_mask) {
+ hpriv->main_irq_mask = new_mask;
+ writelfl(new_mask, hpriv->main_irq_mask_addr);
+ }
+}
+
+static void mv_enable_port_irqs(struct ata_port *ap,
+ unsigned int port_bits)
+{
+ unsigned int shift, hardport, port = ap->port_no;
+ u32 disable_bits, enable_bits;
+
+ MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+
+ disable_bits = (DONE_IRQ | ERR_IRQ) << shift;
+ enable_bits = port_bits << shift;
+ mv_set_main_irq_mask(ap->host, disable_bits, enable_bits);
+}
+
/**
* mv_start_dma - Enable eDMA engine
* @base: port base address
writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
+ mv_enable_port_irqs(ap, DONE_IRQ|ERR_IRQ);
writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
cfg |= (1 << 22); /* enab 4-entry host queue cache */
- if (HAS_PCI(ap->host))
+ if (!IS_SOC(hpriv))
cfg |= (1 << 18); /* enab early completion */
if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
goto out_port_free_dma_mem;
memset(pp->crpb, 0, MV_CRPB_Q_SZ);
+ /* 6041/6081 Rev. "C0" (and newer) are okay with async notify */
+ if (hpriv->hp_flags & MV_HP_ERRATA_60X1C0)
+ ap->flags |= ATA_FLAG_AN;
/*
* For GEN_I, there's no NCQ, so we only allocate a single sg_tbl.
* For later hardware, we need one unique sg_tbl per NCQ tag.
static void mv_port_stop(struct ata_port *ap)
{
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, 0);
mv_port_free_dma_mem(ap);
}
if ((qc->tf.protocol != ATA_PROT_DMA) &&
(qc->tf.protocol != ATA_PROT_NCQ)) {
+ static int limit_warnings = 10;
+ /*
+ * Errata SATA#16, SATA#24: warn if multiple DRQs expected.
+ *
+ * Someday, we might implement special polling workarounds
+ * for these, but it all seems rather unnecessary since we
+ * normally use only DMA for commands which transfer more
+ * than a single block of data.
+ *
+ * Much of the time, this could just work regardless.
+ * So for now, just log the incident, and allow the attempt.
+ */
+ if (limit_warnings > 0 && (qc->nbytes / qc->sect_size) > 1) {
+ --limit_warnings;
+ ata_link_printk(qc->dev->link, KERN_WARNING, DRV_NAME
+ ": attempting PIO w/multiple DRQ: "
+ "this may fail due to h/w errata\n");
+ }
/*
* We're about to send a non-EDMA capable command to the
* port. Turn off EDMA so there won't be problems accessing
* shadow block, etc registers.
*/
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, ERR_IRQ);
mv_pmp_select(ap, qc->dev->link->pmp);
return ata_sff_qc_issue(qc);
}
}
}
+static int mv_req_q_empty(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 in_ptr, out_ptr;
+
+ in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ return (in_ptr == out_ptr); /* 1 == queue_is_empty */
+}
+
static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap)
{
struct mv_port_priv *pp = ap->private_data;
ap->qc_active, failed_links,
ap->nr_active_links);
- if (ap->nr_active_links <= failed_links) {
+ if (ap->nr_active_links <= failed_links && mv_req_q_empty(ap)) {
mv_process_crpb_entries(ap, pp);
mv_stop_edma(ap);
mv_eh_freeze(ap);
ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x",
edma_err_cause, pp->pp_flags);
- if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7))
+ if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause);
+ if (fis_cause & SATA_FIS_IRQ_AN) {
+ u32 ec = edma_err_cause &
+ ~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT);
+ sata_async_notification(ap);
+ if (!ec)
+ return; /* Just an AN; no need for the nukes */
+ ata_ehi_push_desc(ehi, "SDB notify");
+ }
+ }
/*
* All generations share these EDMA error cause bits:
*/
struct ata_host *host = dev_instance;
struct mv_host_priv *hpriv = host->private_data;
unsigned int handled = 0;
- u32 main_irq_cause, main_irq_mask;
+ u32 main_irq_cause, pending_irqs;
spin_lock(&host->lock);
main_irq_cause = readl(hpriv->main_irq_cause_addr);
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
+ pending_irqs = main_irq_cause & hpriv->main_irq_mask;
/*
* Deal with cases where we either have nothing pending, or have read
* a bogus register value which can indicate HW removal or PCI fault.
*/
- if ((main_irq_cause & main_irq_mask) && (main_irq_cause != 0xffffffffU)) {
- if (unlikely((main_irq_cause & PCI_ERR) && HAS_PCI(host)))
+ if (pending_irqs && main_irq_cause != 0xffffffffU) {
+ if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv)))
handled = mv_pci_error(host, hpriv->base);
else
- handled = mv_host_intr(host, main_irq_cause);
+ handled = mv_host_intr(host, pending_irqs);
}
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
- ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
ZERO(hpriv->irq_mask_ofs);
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
int fix_phy_mode4 =
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
- u32 m2, tmp;
+ u32 m2, m3;
if (fix_phy_mode2) {
m2 = readl(port_mmio + PHY_MODE2);
udelay(200);
}
- /* who knows what this magic does */
- tmp = readl(port_mmio + PHY_MODE3);
- tmp &= ~0x7F800000;
- tmp |= 0x2A800000;
- writel(tmp, port_mmio + PHY_MODE3);
-
- if (fix_phy_mode4) {
- u32 m4;
-
- m4 = readl(port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- tmp = readl(port_mmio + PHY_MODE3);
+ /*
+ * Gen-II/IIe PHY_MODE3 errata RM#2:
+ * Achieves better receiver noise performance than the h/w default:
+ */
+ m3 = readl(port_mmio + PHY_MODE3);
+ m3 = (m3 & 0x1f) | (0x5555601 << 5);
- /* workaround for errata FEr SATA#10 (part 1) */
- m4 = (m4 & ~(1 << 1)) | (1 << 0);
+ /* Guideline 88F5182 (GL# SATA-S11) */
+ if (IS_SOC(hpriv))
+ m3 &= ~0x1c;
+ if (fix_phy_mode4) {
+ u32 m4 = readl(port_mmio + PHY_MODE4);
+ /*
+ * Enforce reserved-bit restrictions on GenIIe devices only.
+ * For earlier chipsets, force only the internal config field
+ * (workaround for errata FEr SATA#10 part 1).
+ */
+ if (IS_GEN_IIE(hpriv))
+ m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES;
+ else
+ m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE;
writel(m4, port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- writel(tmp, port_mmio + PHY_MODE3);
}
+ /*
+ * Workaround for 60x1-B2 errata SATA#13:
+ * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3,
+ * so we must always rewrite PHY_MODE3 after PHY_MODE4.
+ */
+ writel(m3, port_mmio + PHY_MODE3);
/* Revert values of pre-emphasis and signal amps to the saved ones */
m2 = readl(port_mmio + PHY_MODE2);
static void mv_eh_freeze(struct ata_port *ap)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
- u32 main_irq_mask;
-
- /* FIXME: handle coalescing completion events properly */
-
mv_stop_edma(ap);
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
-
- /* disable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask &= ~((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, 0);
}
static void mv_eh_thaw(struct ata_port *ap)
{
struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
+ unsigned int port = ap->port_no;
+ unsigned int hardport = mv_hardport_from_port(port);
void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port);
void __iomem *port_mmio = mv_ap_base(ap);
- u32 main_irq_mask, hc_irq_cause;
-
- /* FIXME: handle coalescing completion events properly */
-
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+ u32 hc_irq_cause;
/* clear EDMA errors on this port */
writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
hc_irq_cause &= ~((DEV_IRQ | DMA_IRQ) << hardport);
writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
- /* enable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask |= ((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, ERR_IRQ);
}
/**
void __iomem *mmio = hpriv->base;
u32 reg;
- if (!HAS_PCI(host) || !IS_PCIE(hpriv))
+ if (IS_SOC(hpriv) || !IS_PCIE(hpriv))
return 0; /* not PCI-X capable */
reg = readl(mmio + MV_PCI_MODE_OFS);
if ((reg & MV_PCI_MODE_MASK) == 0)
hp_flags |= MV_HP_CUT_THROUGH;
switch (pdev->revision) {
- case 0x0:
- hp_flags |= MV_HP_ERRATA_XX42A0;
- break;
- case 0x1:
+ case 0x2: /* Rev.B0: the first/only public release */
hp_flags |= MV_HP_ERRATA_60X1C0;
break;
default:
break;
case chip_soc:
hpriv->ops = &mv_soc_ops;
- hp_flags |= MV_HP_ERRATA_60X1C0;
+ hp_flags |= MV_HP_FLAG_SOC | MV_HP_ERRATA_60X1C0;
break;
default:
if (rc)
goto done;
- if (HAS_PCI(host)) {
- hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
- } else {
+ if (IS_SOC(hpriv)) {
hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS;
hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS;
+ } else {
+ hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
}
/* global interrupt mask: 0 == mask everything */
- writel(0, hpriv->main_irq_mask_addr);
+ mv_set_main_irq_mask(host, ~0, 0);
n_hc = mv_get_hc_count(host->ports[0]->flags);
mv_port_init(&ap->ioaddr, port_mmio);
#ifdef CONFIG_PCI
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
unsigned int offset = port_mmio - mmio;
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
}
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
/* Clear any currently outstanding host interrupt conditions */
writelfl(0, mmio + hpriv->irq_cause_ofs);
/* and unmask interrupt generation for host regs */
writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
- if (IS_GEN_I(hpriv))
- writelfl(~HC_MAIN_MASKED_IRQS_5,
- hpriv->main_irq_mask_addr);
- else
- writelfl(~HC_MAIN_MASKED_IRQS,
- hpriv->main_irq_mask_addr);
-
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
- "PCI int cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr),
- readl(mmio + hpriv->irq_cause_ofs),
- readl(mmio + hpriv->irq_mask_ofs));
- } else {
- writelfl(~HC_MAIN_MASKED_IRQS_SOC,
- hpriv->main_irq_mask_addr);
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr));
+
+ /*
+ * enable only global host interrupts for now.
+ * The per-port interrupts get done later as ports are set up.
+ */
+ mv_set_main_irq_mask(host, 0, PCI_ERR);
}
done:
return rc;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff