*
* --> Investigate problems with PCI Message Signalled Interrupts (MSI).
*
- * --> Cache frequently-accessed registers in mv_port_priv to reduce overhead.
- *
* --> Develop a low-power-consumption strategy, and implement it.
*
* --> [Experiment, low priority] Investigate interrupt coalescing.
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/mbus.h>
+#include <linux/bitops.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.20"
+#define DRV_VERSION "1.24"
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
- /* SoC integrated controllers, no PCI interface */
- MV_FLAG_SOC = (1 << 28),
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
ATA_FLAG_PIO_POLLING,
+
MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
+ MV_GENIIE_FLAGS = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
+ ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
+ ATA_FLAG_NCQ | ATA_FLAG_AN,
+
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
CRQB_IOID_SHIFT = 6, /* CRQB Gen-II/IIE IO Id shift */
HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */
HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
- HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
- PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
- HC_MAIN_RSVD),
- HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
- HC_MAIN_RSVD_5),
- HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC),
/* SATAHC registers */
HC_CFG_OFS = 0,
SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
SATA_ACTIVE_OFS = 0x350,
SATA_FIS_IRQ_CAUSE_OFS = 0x364,
+ SATA_FIS_IRQ_AN = (1 << 9), /* async notification */
LTMODE_OFS = 0x30c,
LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */
PHY_MODE3 = 0x310,
PHY_MODE4 = 0x314,
+ PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */
+ PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */
+ PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */
+ PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */
+
PHY_MODE2 = 0x330,
SATA_IFCTL_OFS = 0x344,
SATA_TESTCTL_OFS = 0x348,
EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
- GEN_II_NCQ_MAX_SECTORS = 256, /* max sects/io on Gen2 w/NCQ */
-
/* Host private flags (hp_flags) */
MV_HP_FLAG_MSI = (1 << 0),
MV_HP_ERRATA_50XXB0 = (1 << 1),
MV_HP_ERRATA_50XXB2 = (1 << 2),
MV_HP_ERRATA_60X1B2 = (1 << 3),
MV_HP_ERRATA_60X1C0 = (1 << 4),
- MV_HP_ERRATA_XX42A0 = (1 << 5),
MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */
MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */
MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
+ MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */
+ MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */
+ MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE)
-#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
+#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC)
#define WINDOW_CTRL(i) (0x20030 + ((i) << 4))
#define WINDOW_BASE(i) (0x20034 + ((i) << 4))
unsigned int resp_idx;
u32 pp_flags;
+ unsigned int delayed_eh_pmp_map;
};
struct mv_port_signal {
struct mv_host_priv {
u32 hp_flags;
+ u32 main_irq_mask;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
int n_ports;
void (*reset_bus)(struct ata_host *host, void __iomem *mmio);
};
-static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
-static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
-static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
-static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val);
+static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val);
+static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val);
+static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
+static int mv_qc_defer(struct ata_queued_cmd *qc);
static void mv_qc_prep(struct ata_queued_cmd *qc);
static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
unsigned long deadline);
static int mv_softreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
+static void mv_pmp_error_handler(struct ata_port *ap);
+static void mv_process_crpb_entries(struct ata_port *ap,
+ struct mv_port_priv *pp);
/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below
* because we have to allow room for worst case splitting of
static struct ata_port_operations mv5_ops = {
.inherits = &ata_sff_port_ops,
+ .qc_defer = mv_qc_defer,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
static struct ata_port_operations mv6_ops = {
.inherits = &mv5_ops,
- .qc_defer = sata_pmp_qc_defer_cmd_switch,
.dev_config = mv6_dev_config,
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
.pmp_hardreset = mv_pmp_hardreset,
.pmp_softreset = mv_softreset,
.softreset = mv_softreset,
- .error_handler = sata_pmp_error_handler,
+ .error_handler = mv_pmp_error_handler,
};
static struct ata_port_operations mv_iie_ops = {
.inherits = &mv6_ops,
- .qc_defer = ata_std_qc_defer, /* FIS-based switching */
.dev_config = ATA_OP_NULL,
.qc_prep = mv_qc_prep_iie,
};
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | MV_FLAG_SOC,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
{ PCI_VDEVICE(MARVELL, 0x5041), chip_504x },
{ PCI_VDEVICE(MARVELL, 0x5080), chip_5080 },
{ PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
- /* RocketRAID 1740/174x have different identifiers */
+ /* RocketRAID 1720/174x have different identifiers */
+ { PCI_VDEVICE(TTI, 0x1720), chip_6042 },
{ PCI_VDEVICE(TTI, 0x1740), chip_508x },
{ PCI_VDEVICE(TTI, 0x1742), chip_508x },
writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crqb_dma & 0xffffffff) | index,
- port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+ writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
/*
* initialize response queue
WARN_ON(pp->crpb_dma & 0xff);
writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crpb_dma & 0xffffffff) | index,
- port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
-
+ writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_set_main_irq_mask(struct ata_host *host,
+ u32 disable_bits, u32 enable_bits)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ u32 old_mask, new_mask;
+
+ old_mask = hpriv->main_irq_mask;
+ new_mask = (old_mask & ~disable_bits) | enable_bits;
+ if (new_mask != old_mask) {
+ hpriv->main_irq_mask = new_mask;
+ writelfl(new_mask, hpriv->main_irq_mask_addr);
+ }
+}
+
+static void mv_enable_port_irqs(struct ata_port *ap,
+ unsigned int port_bits)
+{
+ unsigned int shift, hardport, port = ap->port_no;
+ u32 disable_bits, enable_bits;
+
+ MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+
+ disable_bits = (DONE_IRQ | ERR_IRQ) << shift;
+ enable_bits = port_bits << shift;
+ mv_set_main_irq_mask(ap->host, disable_bits, enable_bits);
+}
+
/**
* mv_start_dma - Enable eDMA engine
* @base: port base address
struct mv_host_priv *hpriv = ap->host->private_data;
int hardport = mv_hardport_from_port(ap->port_no);
void __iomem *hc_mmio = mv_hc_base_from_port(
- mv_host_base(ap->host), hardport);
- u32 hc_irq_cause, ipending;
+ mv_host_base(ap->host), ap->port_no);
+ u32 hc_irq_cause;
/* clear EDMA event indicators, if any */
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* clear EDMA interrupt indicator, if any */
- hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- ipending = (DEV_IRQ | DMA_IRQ) << hardport;
- if (hc_irq_cause & ipending) {
- writelfl(hc_irq_cause & ~ipending,
- hc_mmio + HC_IRQ_CAUSE_OFS);
- }
+ /* clear pending irq events */
+ hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
+ writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
mv_edma_cfg(ap, want_ncq);
/* clear FIS IRQ Cause */
- writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ if (IS_GEN_IIE(hpriv))
+ writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
+ mv_enable_port_irqs(ap, DONE_IRQ|ERR_IRQ);
writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
/*
* Wait for the EDMA engine to finish transactions in progress.
+ * No idea what a good "timeout" value might be, but measurements
+ * indicate that it often requires hundreds of microseconds
+ * with two drives in-use. So we use the 15msec value above
+ * as a rough guess at what even more drives might require.
*/
for (i = 0; i < timeout; ++i) {
u32 edma_stat = readl(port_mmio + EDMA_STATUS_OFS);
return ofs;
}
-static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
+static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
- *val = readl(mv_ap_base(ap) + ofs);
+ *val = readl(mv_ap_base(link->ap) + ofs);
return 0;
} else
return -EINVAL;
}
-static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
- writelfl(val, mv_ap_base(ap) + ofs);
+ writelfl(val, mv_ap_base(link->ap) + ofs);
return 0;
} else
return -EINVAL;
*
* Gen-II does not support NCQ over a port multiplier
* (no FIS-based switching).
- *
- * We don't have hob_nsect when doing NCQ commands on Gen-II.
- * See mv_qc_prep() for more info.
*/
if (adev->flags & ATA_DFLAG_NCQ) {
if (sata_pmp_attached(adev->link->ap)) {
adev->flags &= ~ATA_DFLAG_NCQ;
ata_dev_printk(adev, KERN_INFO,
"NCQ disabled for command-based switching\n");
- } else if (adev->max_sectors > GEN_II_NCQ_MAX_SECTORS) {
- adev->max_sectors = GEN_II_NCQ_MAX_SECTORS;
- ata_dev_printk(adev, KERN_INFO,
- "max_sectors limited to %u for NCQ\n",
- adev->max_sectors);
}
}
}
-static void mv_config_fbs(void __iomem *port_mmio, int enable_fbs)
+static int mv_qc_defer(struct ata_queued_cmd *qc)
{
- u32 old_fiscfg, new_fiscfg, old_ltmode, new_ltmode;
+ struct ata_link *link = qc->dev->link;
+ struct ata_port *ap = link->ap;
+ struct mv_port_priv *pp = ap->private_data;
+
+ /*
+ * Don't allow new commands if we're in a delayed EH state
+ * for NCQ and/or FIS-based switching.
+ */
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH)
+ return ATA_DEFER_PORT;
/*
- * Various bit settings required for operation
- * in FIS-based switching (fbs) mode on GenIIe:
+ * If the port is completely idle, then allow the new qc.
*/
- old_fiscfg = readl(port_mmio + FISCFG_OFS);
- old_ltmode = readl(port_mmio + LTMODE_OFS);
- if (enable_fbs) {
- new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
- new_ltmode = old_ltmode | LTMODE_BIT8;
- } else { /* disable fbs */
- new_fiscfg = old_fiscfg & ~FISCFG_SINGLE_SYNC;
- new_ltmode = old_ltmode & ~LTMODE_BIT8;
+ if (ap->nr_active_links == 0)
+ return 0;
+
+ /*
+ * The port is operating in host queuing mode (EDMA) with NCQ
+ * enabled, allow multiple NCQ commands. EDMA also allows
+ * queueing multiple DMA commands but libata core currently
+ * doesn't allow it.
+ */
+ if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) &&
+ (pp->pp_flags & MV_PP_FLAG_NCQ_EN) && ata_is_ncq(qc->tf.protocol))
+ return 0;
+
+ return ATA_DEFER_PORT;
+}
+
+static void mv_config_fbs(void __iomem *port_mmio, int want_ncq, int want_fbs)
+{
+ u32 new_fiscfg, old_fiscfg;
+ u32 new_ltmode, old_ltmode;
+ u32 new_haltcond, old_haltcond;
+
+ old_fiscfg = readl(port_mmio + FISCFG_OFS);
+ old_ltmode = readl(port_mmio + LTMODE_OFS);
+ old_haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+
+ new_fiscfg = old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
+ new_ltmode = old_ltmode & ~LTMODE_BIT8;
+ new_haltcond = old_haltcond | EDMA_ERR_DEV;
+
+ if (want_fbs) {
+ new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
+ new_ltmode = old_ltmode | LTMODE_BIT8;
+ if (want_ncq)
+ new_haltcond &= ~EDMA_ERR_DEV;
+ else
+ new_fiscfg |= FISCFG_WAIT_DEV_ERR;
}
+
if (new_fiscfg != old_fiscfg)
writelfl(new_fiscfg, port_mmio + FISCFG_OFS);
if (new_ltmode != old_ltmode)
writelfl(new_ltmode, port_mmio + LTMODE_OFS);
+ if (new_haltcond != old_haltcond)
+ writelfl(new_haltcond, port_mmio + EDMA_HALTCOND_OFS);
+}
+
+static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
+{
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ u32 old, new;
+
+ /* workaround for 88SX60x1 FEr SATA#25 (part 1) */
+ old = readl(hpriv->base + MV_GPIO_PORT_CTL_OFS);
+ if (want_ncq)
+ new = old | (1 << 22);
+ else
+ new = old & ~(1 << 22);
+ if (new != old)
+ writel(new, hpriv->base + MV_GPIO_PORT_CTL_OFS);
}
static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
/* set up non-NCQ EDMA configuration */
cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */
+ pp->pp_flags &= ~MV_PP_FLAG_FBS_EN;
if (IS_GEN_I(hpriv))
cfg |= (1 << 8); /* enab config burst size mask */
- else if (IS_GEN_II(hpriv))
+ else if (IS_GEN_II(hpriv)) {
cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN;
+ mv_60x1_errata_sata25(ap, want_ncq);
+
+ } else if (IS_GEN_IIE(hpriv)) {
+ int want_fbs = sata_pmp_attached(ap);
+ /*
+ * Possible future enhancement:
+ *
+ * The chip can use FBS with non-NCQ, if we allow it,
+ * But first we need to have the error handling in place
+ * for this mode (datasheet section 7.3.15.4.2.3).
+ * So disallow non-NCQ FBS for now.
+ */
+ want_fbs &= want_ncq;
+
+ mv_config_fbs(port_mmio, want_ncq, want_fbs);
+
+ if (want_fbs) {
+ pp->pp_flags |= MV_PP_FLAG_FBS_EN;
+ cfg |= EDMA_CFG_EDMA_FBS; /* FIS-based switching */
+ }
- else if (IS_GEN_IIE(hpriv)) {
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
cfg |= (1 << 22); /* enab 4-entry host queue cache */
- if (HAS_PCI(ap->host))
+ if (!IS_SOC(hpriv))
cfg |= (1 << 18); /* enab early completion */
if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
-
- if (want_ncq && sata_pmp_attached(ap)) {
- cfg |= EDMA_CFG_EDMA_FBS; /* FIS-based switching */
- mv_config_fbs(port_mmio, 1);
- } else {
- mv_config_fbs(port_mmio, 0);
- }
}
if (want_ncq) {
goto out_port_free_dma_mem;
memset(pp->crpb, 0, MV_CRPB_Q_SZ);
+ /* 6041/6081 Rev. "C0" (and newer) are okay with async notify */
+ if (hpriv->hp_flags & MV_HP_ERRATA_60X1C0)
+ ap->flags |= ATA_FLAG_AN;
/*
* For GEN_I, there's no NCQ, so we only allocate a single sg_tbl.
* For later hardware, we need one unique sg_tbl per NCQ tag.
static void mv_port_stop(struct ata_port *ap)
{
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, 0);
mv_port_free_dma_mem(ap);
}
* only 11 bytes...so we must pick and choose required
* registers based on the command. So, we drop feature and
* hob_feature for [RW] DMA commands, but they are needed for
- * NCQ. NCQ will drop hob_nsect.
+ * NCQ. NCQ will drop hob_nsect, which is not needed there
+ * (nsect is used only for the tag; feat/hob_feat hold true nsect).
*/
switch (tf->command) {
case ATA_CMD_READ:
if ((qc->tf.protocol != ATA_PROT_DMA) &&
(qc->tf.protocol != ATA_PROT_NCQ)) {
+ static int limit_warnings = 10;
+ /*
+ * Errata SATA#16, SATA#24: warn if multiple DRQs expected.
+ *
+ * Someday, we might implement special polling workarounds
+ * for these, but it all seems rather unnecessary since we
+ * normally use only DMA for commands which transfer more
+ * than a single block of data.
+ *
+ * Much of the time, this could just work regardless.
+ * So for now, just log the incident, and allow the attempt.
+ */
+ if (limit_warnings > 0 && (qc->nbytes / qc->sect_size) > 1) {
+ --limit_warnings;
+ ata_link_printk(qc->dev->link, KERN_WARNING, DRV_NAME
+ ": attempting PIO w/multiple DRQ: "
+ "this may fail due to h/w errata\n");
+ }
/*
* We're about to send a non-EDMA capable command to the
* port. Turn off EDMA so there won't be problems accessing
* shadow block, etc registers.
*/
mv_stop_edma(ap);
+ mv_enable_port_irqs(ap, ERR_IRQ);
mv_pmp_select(ap, qc->dev->link->pmp);
return ata_sff_qc_issue(qc);
}
return qc;
}
-static void mv_unexpected_intr(struct ata_port *ap)
+static void mv_pmp_error_handler(struct ata_port *ap)
{
+ unsigned int pmp, pmp_map;
struct mv_port_priv *pp = ap->private_data;
- struct ata_eh_info *ehi = &ap->link.eh_info;
- char *when = "";
+
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) {
+ /*
+ * Perform NCQ error analysis on failed PMPs
+ * before we freeze the port entirely.
+ *
+ * The failed PMPs are marked earlier by mv_pmp_eh_prep().
+ */
+ pmp_map = pp->delayed_eh_pmp_map;
+ pp->pp_flags &= ~MV_PP_FLAG_DELAYED_EH;
+ for (pmp = 0; pmp_map != 0; pmp++) {
+ unsigned int this_pmp = (1 << pmp);
+ if (pmp_map & this_pmp) {
+ struct ata_link *link = &ap->pmp_link[pmp];
+ pmp_map &= ~this_pmp;
+ ata_eh_analyze_ncq_error(link);
+ }
+ }
+ ata_port_freeze(ap);
+ }
+ sata_pmp_error_handler(ap);
+}
+
+static unsigned int mv_get_err_pmp_map(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+
+ return readl(port_mmio + SATA_TESTCTL_OFS) >> 16;
+}
+
+static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map)
+{
+ struct ata_eh_info *ehi;
+ unsigned int pmp;
/*
- * We got a device interrupt from something that
- * was supposed to be using EDMA or polling.
+ * Initialize EH info for PMPs which saw device errors
+ */
+ ehi = &ap->link.eh_info;
+ for (pmp = 0; pmp_map != 0; pmp++) {
+ unsigned int this_pmp = (1 << pmp);
+ if (pmp_map & this_pmp) {
+ struct ata_link *link = &ap->pmp_link[pmp];
+
+ pmp_map &= ~this_pmp;
+ ehi = &link->eh_info;
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "dev err");
+ ehi->err_mask |= AC_ERR_DEV;
+ ehi->action |= ATA_EH_RESET;
+ ata_link_abort(link);
+ }
+ }
+}
+
+static int mv_req_q_empty(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 in_ptr, out_ptr;
+
+ in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS)
+ >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK;
+ return (in_ptr == out_ptr); /* 1 == queue_is_empty */
+}
+
+static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap)
+{
+ struct mv_port_priv *pp = ap->private_data;
+ int failed_links;
+ unsigned int old_map, new_map;
+
+ /*
+ * Device error during FBS+NCQ operation:
+ *
+ * Set a port flag to prevent further I/O being enqueued.
+ * Leave the EDMA running to drain outstanding commands from this port.
+ * Perform the post-mortem/EH only when all responses are complete.
+ * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.2).
+ */
+ if (!(pp->pp_flags & MV_PP_FLAG_DELAYED_EH)) {
+ pp->pp_flags |= MV_PP_FLAG_DELAYED_EH;
+ pp->delayed_eh_pmp_map = 0;
+ }
+ old_map = pp->delayed_eh_pmp_map;
+ new_map = old_map | mv_get_err_pmp_map(ap);
+
+ if (old_map != new_map) {
+ pp->delayed_eh_pmp_map = new_map;
+ mv_pmp_eh_prep(ap, new_map & ~old_map);
+ }
+ failed_links = hweight16(new_map);
+
+ ata_port_printk(ap, KERN_INFO, "%s: pmp_map=%04x qc_map=%04x "
+ "failed_links=%d nr_active_links=%d\n",
+ __func__, pp->delayed_eh_pmp_map,
+ ap->qc_active, failed_links,
+ ap->nr_active_links);
+
+ if (ap->nr_active_links <= failed_links && mv_req_q_empty(ap)) {
+ mv_process_crpb_entries(ap, pp);
+ mv_stop_edma(ap);
+ mv_eh_freeze(ap);
+ ata_port_printk(ap, KERN_INFO, "%s: done\n", __func__);
+ return 1; /* handled */
+ }
+ ata_port_printk(ap, KERN_INFO, "%s: waiting\n", __func__);
+ return 1; /* handled */
+}
+
+static int mv_handle_fbs_non_ncq_dev_err(struct ata_port *ap)
+{
+ /*
+ * Possible future enhancement:
+ *
+ * FBS+non-NCQ operation is not yet implemented.
+ * See related notes in mv_edma_cfg().
+ *
+ * Device error during FBS+non-NCQ operation:
+ *
+ * We need to snapshot the shadow registers for each failed command.
+ * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.3).
*/
+ return 0; /* not handled */
+}
+
+static int mv_handle_dev_err(struct ata_port *ap, u32 edma_err_cause)
+{
+ struct mv_port_priv *pp = ap->private_data;
+
+ if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN))
+ return 0; /* EDMA was not active: not handled */
+ if (!(pp->pp_flags & MV_PP_FLAG_FBS_EN))
+ return 0; /* FBS was not active: not handled */
+
+ if (!(edma_err_cause & EDMA_ERR_DEV))
+ return 0; /* non DEV error: not handled */
+ edma_err_cause &= ~EDMA_ERR_IRQ_TRANSIENT;
+ if (edma_err_cause & ~(EDMA_ERR_DEV | EDMA_ERR_SELF_DIS))
+ return 0; /* other problems: not handled */
+
+ if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) {
+ /*
+ * EDMA should NOT have self-disabled for this case.
+ * If it did, then something is wrong elsewhere,
+ * and we cannot handle it here.
+ */
+ if (edma_err_cause & EDMA_ERR_SELF_DIS) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s: err_cause=0x%x pp_flags=0x%x\n",
+ __func__, edma_err_cause, pp->pp_flags);
+ return 0; /* not handled */
+ }
+ return mv_handle_fbs_ncq_dev_err(ap);
+ } else {
+ /*
+ * EDMA should have self-disabled for this case.
+ * If it did not, then something is wrong elsewhere,
+ * and we cannot handle it here.
+ */
+ if (!(edma_err_cause & EDMA_ERR_SELF_DIS)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s: err_cause=0x%x pp_flags=0x%x\n",
+ __func__, edma_err_cause, pp->pp_flags);
+ return 0; /* not handled */
+ }
+ return mv_handle_fbs_non_ncq_dev_err(ap);
+ }
+ return 0; /* not handled */
+}
+
+static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled)
+{
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ char *when = "idle";
+
ata_ehi_clear_desc(ehi);
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
- when = " while EDMA enabled";
+ if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+ when = "disabled";
+ } else if (edma_was_enabled) {
+ when = "EDMA enabled";
} else {
struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && (qc->tf.flags & ATA_TFLAG_POLLING))
- when = " while polling";
+ when = "polling";
}
- ata_ehi_push_desc(ehi, "unexpected device interrupt%s", when);
+ ata_ehi_push_desc(ehi, "unexpected device interrupt while %s", when);
ehi->err_mask |= AC_ERR_OTHER;
ehi->action |= ATA_EH_RESET;
ata_port_freeze(ap);
/**
* mv_err_intr - Handle error interrupts on the port
* @ap: ATA channel to manipulate
- * @qc: affected command (non-NCQ), or NULL
*
* Most cases require a full reset of the chip's state machine,
* which also performs a COMRESET.
* LOCKING:
* Inherited from caller.
*/
-static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
+static void mv_err_intr(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
u32 edma_err_cause, eh_freeze_mask, serr = 0;
+ u32 fis_cause = 0;
struct mv_port_priv *pp = ap->private_data;
struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int action = 0, err_mask = 0;
struct ata_eh_info *ehi = &ap->link.eh_info;
-
- ata_ehi_clear_desc(ehi);
+ struct ata_queued_cmd *qc;
+ int abort = 0;
/*
- * Read and clear the err_cause bits. This won't actually
- * clear for some errors (eg. SError), but we will be doing
- * a hard reset in those cases regardless, which *will* clear it.
+ * Read and clear the SError and err_cause bits.
+ * For GenIIe, if EDMA_ERR_TRANS_IRQ_7 is set, we also must read/clear
+ * the FIS_IRQ_CAUSE register before clearing edma_err_cause.
*/
+ sata_scr_read(&ap->link, SCR_ERROR, &serr);
+ sata_scr_write_flush(&ap->link, SCR_ERROR, serr);
+
edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
+ fis_cause = readl(port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ writelfl(~fis_cause, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ }
writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- ata_ehi_push_desc(ehi, "edma_err_cause=%08x", edma_err_cause);
+ if (edma_err_cause & EDMA_ERR_DEV) {
+ /*
+ * Device errors during FIS-based switching operation
+ * require special handling.
+ */
+ if (mv_handle_dev_err(ap, edma_err_cause))
+ return;
+ }
+ qc = mv_get_active_qc(ap);
+ ata_ehi_clear_desc(ehi);
+ ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x",
+ edma_err_cause, pp->pp_flags);
+
+ if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) {
+ ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause);
+ if (fis_cause & SATA_FIS_IRQ_AN) {
+ u32 ec = edma_err_cause &
+ ~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT);
+ sata_async_notification(ap);
+ if (!ec)
+ return; /* Just an AN; no need for the nukes */
+ ata_ehi_push_desc(ehi, "SDB notify");
+ }
+ }
/*
* All generations share these EDMA error cause bits:
*/
- if (edma_err_cause & EDMA_ERR_DEV)
+ if (edma_err_cause & EDMA_ERR_DEV) {
err_mask |= AC_ERR_DEV;
+ action |= ATA_EH_RESET;
+ ata_ehi_push_desc(ehi, "dev error");
+ }
if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
EDMA_ERR_CRQB_PAR | EDMA_ERR_CRPB_PAR |
EDMA_ERR_INTRL_PAR)) {
ata_ehi_push_desc(ehi, "EDMA self-disable");
}
if (edma_err_cause & EDMA_ERR_SERR) {
- /*
- * Ensure that we read our own SCR, not a pmp link SCR:
- */
- ap->ops->scr_read(ap, SCR_ERROR, &serr);
- /*
- * Don't clear SError here; leave it for libata-eh:
- */
ata_ehi_push_desc(ehi, "SError=%08x", serr);
err_mask |= AC_ERR_ATA_BUS;
action |= ATA_EH_RESET;
else
ehi->err_mask |= err_mask;
- if (edma_err_cause & eh_freeze_mask)
+ if (err_mask == AC_ERR_DEV) {
+ /*
+ * Cannot do ata_port_freeze() here,
+ * because it would kill PIO access,
+ * which is needed for further diagnosis.
+ */
+ mv_eh_freeze(ap);
+ abort = 1;
+ } else if (edma_err_cause & eh_freeze_mask) {
+ /*
+ * Note to self: ata_port_freeze() calls ata_port_abort()
+ */
ata_port_freeze(ap);
- else
- ata_port_abort(ap);
+ } else {
+ abort = 1;
+ }
+
+ if (abort) {
+ if (qc)
+ ata_link_abort(qc->dev->link);
+ else
+ ata_port_abort(ap);
+ }
}
static void mv_process_crpb_response(struct ata_port *ap,
}
}
ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT;
- qc->err_mask |= ac_err_mask(ata_status);
- ata_qc_complete(qc);
+ if (!ac_err_mask(ata_status))
+ ata_qc_complete(qc);
+ /* else: leave it for mv_err_intr() */
} else {
ata_port_printk(ap, KERN_ERR, "%s: no qc for tag=%d\n",
__func__, tag);
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_port_intr(struct ata_port *ap, u32 port_cause)
+{
+ struct mv_port_priv *pp;
+ int edma_was_enabled;
+
+ if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+ mv_unexpected_intr(ap, 0);
+ return;
+ }
+ /*
+ * Grab a snapshot of the EDMA_EN flag setting,
+ * so that we have a consistent view for this port,
+ * even if something we call of our routines changes it.
+ */
+ pp = ap->private_data;
+ edma_was_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN);
+ /*
+ * Process completed CRPB response(s) before other events.
+ */
+ if (edma_was_enabled && (port_cause & DONE_IRQ)) {
+ mv_process_crpb_entries(ap, pp);
+ if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH)
+ mv_handle_fbs_ncq_dev_err(ap);
+ }
+ /*
+ * Handle chip-reported errors, or continue on to handle PIO.
+ */
+ if (unlikely(port_cause & ERR_IRQ)) {
+ mv_err_intr(ap);
+ } else if (!edma_was_enabled) {
+ struct ata_queued_cmd *qc = mv_get_active_qc(ap);
+ if (qc)
+ ata_sff_host_intr(ap, qc);
+ else
+ mv_unexpected_intr(ap, edma_was_enabled);
+ }
+}
+
/**
* mv_host_intr - Handle all interrupts on the given host controller
* @host: host specific structure
static int mv_host_intr(struct ata_host *host, u32 main_irq_cause)
{
struct mv_host_priv *hpriv = host->private_data;
- void __iomem *mmio = hpriv->base, *hc_mmio = NULL;
- u32 hc_irq_cause = 0;
+ void __iomem *mmio = hpriv->base, *hc_mmio;
unsigned int handled = 0, port;
for (port = 0; port < hpriv->n_ports; port++) {
struct ata_port *ap = host->ports[port];
- struct mv_port_priv *pp;
- unsigned int shift, hardport, port_cause;
- /*
- * When we move to the second hc, flag our cached
- * copies of hc_mmio (and hc_irq_cause) as invalid again.
- */
- if (port == MV_PORTS_PER_HC)
- hc_mmio = NULL;
- /*
- * Do nothing if port is not interrupting or is disabled:
- */
+ unsigned int p, shift, hardport, port_cause;
+
MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
- port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ);
- if (!port_cause || !ap || (ap->flags & ATA_FLAG_DISABLED))
- continue;
/*
- * Each hc within the host has its own hc_irq_cause register.
- * We defer reading it until we know we need it, right now:
- *
- * FIXME later: we don't really need to read this register
- * (some logic changes required below if we go that way),
- * because it doesn't tell us anything new. But we do need
- * to write to it, outside the top of this loop,
- * to reset the interrupt triggers for next time.
+ * Each hc within the host has its own hc_irq_cause register,
+ * where the interrupting ports bits get ack'd.
*/
- if (!hc_mmio) {
+ if (hardport == 0) { /* first port on this hc ? */
+ u32 hc_cause = (main_irq_cause >> shift) & HC0_IRQ_PEND;
+ u32 port_mask, ack_irqs;
+ /*
+ * Skip this entire hc if nothing pending for any ports
+ */
+ if (!hc_cause) {
+ port += MV_PORTS_PER_HC - 1;
+ continue;
+ }
+ /*
+ * We don't need/want to read the hc_irq_cause register,
+ * because doing so hurts performance, and
+ * main_irq_cause already gives us everything we need.
+ *
+ * But we do have to *write* to the hc_irq_cause to ack
+ * the ports that we are handling this time through.
+ *
+ * This requires that we create a bitmap for those
+ * ports which interrupted us, and use that bitmap
+ * to ack (only) those ports via hc_irq_cause.
+ */
+ ack_irqs = 0;
+ for (p = 0; p < MV_PORTS_PER_HC; ++p) {
+ if ((port + p) >= hpriv->n_ports)
+ break;
+ port_mask = (DONE_IRQ | ERR_IRQ) << (p * 2);
+ if (hc_cause & port_mask)
+ ack_irqs |= (DMA_IRQ | DEV_IRQ) << p;
+ }
hc_mmio = mv_hc_base_from_port(mmio, port);
- hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE_OFS);
handled = 1;
}
/*
- * Process completed CRPB response(s) before other events.
- */
- pp = ap->private_data;
- if (hc_irq_cause & (DMA_IRQ << hardport)) {
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN)
- mv_process_crpb_entries(ap, pp);
- }
- /*
- * Handle chip-reported errors, or continue on to handle PIO.
+ * Handle interrupts signalled for this port:
*/
- if (unlikely(port_cause & ERR_IRQ)) {
- mv_err_intr(ap, mv_get_active_qc(ap));
- } else if (hc_irq_cause & (DEV_IRQ << hardport)) {
- if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
- struct ata_queued_cmd *qc = mv_get_active_qc(ap);
- if (qc) {
- ata_sff_host_intr(ap, qc);
- continue;
- }
- }
- mv_unexpected_intr(ap);
- }
+ port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ);
+ if (port_cause)
+ mv_port_intr(ap, port_cause);
}
return handled;
}
struct ata_host *host = dev_instance;
struct mv_host_priv *hpriv = host->private_data;
unsigned int handled = 0;
- u32 main_irq_cause, main_irq_mask;
+ u32 main_irq_cause, pending_irqs;
spin_lock(&host->lock);
main_irq_cause = readl(hpriv->main_irq_cause_addr);
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
+ pending_irqs = main_irq_cause & hpriv->main_irq_mask;
/*
* Deal with cases where we either have nothing pending, or have read
* a bogus register value which can indicate HW removal or PCI fault.
*/
- if ((main_irq_cause & main_irq_mask) && (main_irq_cause != 0xffffffffU)) {
- if (unlikely((main_irq_cause & PCI_ERR) && HAS_PCI(host)))
+ if (pending_irqs && main_irq_cause != 0xffffffffU) {
+ if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv)))
handled = mv_pci_error(host, hpriv->base);
else
- handled = mv_host_intr(host, main_irq_cause);
+ handled = mv_host_intr(host, pending_irqs);
}
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
return ofs;
}
-static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
+static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_host_priv *hpriv = link->ap->host->private_data;
void __iomem *mmio = hpriv->base;
- void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
+ void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
return -EINVAL;
}
-static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_host_priv *hpriv = link->ap->host->private_data;
void __iomem *mmio = hpriv->base;
- void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
+ void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
ZERO(MV_PCI_DISC_TIMER);
ZERO(MV_PCI_MSI_TRIGGER);
writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT_OFS);
- ZERO(PCI_HC_MAIN_IRQ_MASK_OFS);
ZERO(MV_PCI_SERR_MASK);
ZERO(hpriv->irq_cause_ofs);
ZERO(hpriv->irq_mask_ofs);
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
int fix_phy_mode4 =
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
- u32 m2, tmp;
+ u32 m2, m3;
if (fix_phy_mode2) {
m2 = readl(port_mmio + PHY_MODE2);
udelay(200);
}
- /* who knows what this magic does */
- tmp = readl(port_mmio + PHY_MODE3);
- tmp &= ~0x7F800000;
- tmp |= 0x2A800000;
- writel(tmp, port_mmio + PHY_MODE3);
-
- if (fix_phy_mode4) {
- u32 m4;
-
- m4 = readl(port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- tmp = readl(port_mmio + PHY_MODE3);
+ /*
+ * Gen-II/IIe PHY_MODE3 errata RM#2:
+ * Achieves better receiver noise performance than the h/w default:
+ */
+ m3 = readl(port_mmio + PHY_MODE3);
+ m3 = (m3 & 0x1f) | (0x5555601 << 5);
- /* workaround for errata FEr SATA#10 (part 1) */
- m4 = (m4 & ~(1 << 1)) | (1 << 0);
+ /* Guideline 88F5182 (GL# SATA-S11) */
+ if (IS_SOC(hpriv))
+ m3 &= ~0x1c;
+ if (fix_phy_mode4) {
+ u32 m4 = readl(port_mmio + PHY_MODE4);
+ /*
+ * Enforce reserved-bit restrictions on GenIIe devices only.
+ * For earlier chipsets, force only the internal config field
+ * (workaround for errata FEr SATA#10 part 1).
+ */
+ if (IS_GEN_IIE(hpriv))
+ m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES;
+ else
+ m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE;
writel(m4, port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- writel(tmp, port_mmio + PHY_MODE3);
}
+ /*
+ * Workaround for 60x1-B2 errata SATA#13:
+ * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3,
+ * so we must always rewrite PHY_MODE3 after PHY_MODE4.
+ */
+ writel(m3, port_mmio + PHY_MODE3);
/* Revert values of pre-emphasis and signal amps to the saved ones */
m2 = readl(port_mmio + PHY_MODE2);
rc = sata_link_hardreset(link, timing, deadline + extra,
&online, NULL);
+ rc = online ? -EAGAIN : rc;
if (rc)
return rc;
sata_scr_read(link, SCR_STATUS, &sstatus);
static void mv_eh_freeze(struct ata_port *ap)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
- u32 main_irq_mask;
-
- /* FIXME: handle coalescing completion events properly */
-
mv_stop_edma(ap);
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
-
- /* disable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask &= ~((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, 0);
}
static void mv_eh_thaw(struct ata_port *ap)
{
struct mv_host_priv *hpriv = ap->host->private_data;
- unsigned int shift, hardport, port = ap->port_no;
+ unsigned int port = ap->port_no;
+ unsigned int hardport = mv_hardport_from_port(port);
void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port);
void __iomem *port_mmio = mv_ap_base(ap);
- u32 main_irq_mask, hc_irq_cause;
-
- /* FIXME: handle coalescing completion events properly */
-
- MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport);
+ u32 hc_irq_cause;
/* clear EDMA errors on this port */
writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
/* clear pending irq events */
- hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- hc_irq_cause &= ~((DEV_IRQ | DMA_IRQ) << hardport);
+ hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
- /* enable assertion of portN err, done events */
- main_irq_mask = readl(hpriv->main_irq_mask_addr);
- main_irq_mask |= ((DONE_IRQ | ERR_IRQ) << shift);
- writelfl(main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_enable_port_irqs(ap, ERR_IRQ);
}
/**
void __iomem *mmio = hpriv->base;
u32 reg;
- if (!HAS_PCI(host) || !IS_PCIE(hpriv))
+ if (IS_SOC(hpriv) || !IS_PCIE(hpriv))
return 0; /* not PCI-X capable */
reg = readl(mmio + MV_PCI_MODE_OFS);
if ((reg & MV_PCI_MODE_MASK) == 0)
hp_flags |= MV_HP_CUT_THROUGH;
switch (pdev->revision) {
- case 0x0:
- hp_flags |= MV_HP_ERRATA_XX42A0;
- break;
- case 0x1:
+ case 0x2: /* Rev.B0: the first/only public release */
hp_flags |= MV_HP_ERRATA_60X1C0;
break;
default:
break;
case chip_soc:
hpriv->ops = &mv_soc_ops;
- hp_flags |= MV_HP_ERRATA_60X1C0;
+ hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE |
+ MV_HP_ERRATA_60X1C0;
break;
default:
if (rc)
goto done;
- if (HAS_PCI(host)) {
- hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
- } else {
+ if (IS_SOC(hpriv)) {
hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS;
hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS;
+ } else {
+ hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
}
/* global interrupt mask: 0 == mask everything */
- writel(0, hpriv->main_irq_mask_addr);
+ mv_set_main_irq_mask(host, ~0, 0);
n_hc = mv_get_hc_count(host->ports[0]->flags);
mv_port_init(&ap->ioaddr, port_mmio);
#ifdef CONFIG_PCI
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
unsigned int offset = port_mmio - mmio;
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
}
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
/* Clear any currently outstanding host interrupt conditions */
writelfl(0, mmio + hpriv->irq_cause_ofs);
/* and unmask interrupt generation for host regs */
writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
- if (IS_GEN_I(hpriv))
- writelfl(~HC_MAIN_MASKED_IRQS_5,
- hpriv->main_irq_mask_addr);
- else
- writelfl(~HC_MAIN_MASKED_IRQS,
- hpriv->main_irq_mask_addr);
-
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
- "PCI int cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr),
- readl(mmio + hpriv->irq_cause_ofs),
- readl(mmio + hpriv->irq_mask_ofs));
- } else {
- writelfl(~HC_MAIN_MASKED_IRQS_SOC,
- hpriv->main_irq_mask_addr);
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
- readl(hpriv->main_irq_cause_addr),
- readl(hpriv->main_irq_mask_addr));
+
+ /*
+ * enable only global host interrupts for now.
+ * The per-port interrupts get done later as ports are set up.
+ */
+ mv_set_main_irq_mask(host, 0, PCI_ERR);
}
done:
return rc;