#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.21"
+#define DRV_VERSION "1.24"
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
- /* SoC integrated controllers, no PCI interface */
- MV_FLAG_SOC = (1 << 28),
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
PHY_MODE3 = 0x310,
PHY_MODE4 = 0x314,
+ PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */
+ PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */
+ PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */
+ PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */
+
PHY_MODE2 = 0x330,
SATA_IFCTL_OFS = 0x344,
SATA_TESTCTL_OFS = 0x348,
MV_HP_ERRATA_50XXB2 = (1 << 2),
MV_HP_ERRATA_60X1B2 = (1 << 3),
MV_HP_ERRATA_60X1C0 = (1 << 4),
- MV_HP_ERRATA_XX42A0 = (1 << 5),
MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */
MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */
MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
+ MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
#define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II)
#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE)
-#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC))
+#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC)
#define WINDOW_CTRL(i) (0x20030 + ((i) << 4))
#define WINDOW_BASE(i) (0x20034 + ((i) << 4))
void (*reset_bus)(struct ata_host *host, void __iomem *mmio);
};
-static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
-static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
-static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val);
-static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
+static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val);
+static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val);
+static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val);
+static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
static int mv_qc_defer(struct ata_queued_cmd *qc);
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_GENIIE_FLAGS | MV_FLAG_SOC,
+ .flags = MV_GENIIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
{ PCI_VDEVICE(MARVELL, 0x5041), chip_504x },
{ PCI_VDEVICE(MARVELL, 0x5080), chip_5080 },
{ PCI_VDEVICE(MARVELL, 0x5081), chip_508x },
- /* RocketRAID 1740/174x have different identifiers */
+ /* RocketRAID 1720/174x have different identifiers */
+ { PCI_VDEVICE(TTI, 0x1720), chip_6042 },
{ PCI_VDEVICE(TTI, 0x1740), chip_508x },
{ PCI_VDEVICE(TTI, 0x1742), chip_508x },
writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crqb_dma & 0xffffffff) | index,
- port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
+ writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
/*
* initialize response queue
WARN_ON(pp->crpb_dma & 0xff);
writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
-
- if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
- writelfl((pp->crpb_dma & 0xffffffff) | index,
- port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
- else
- writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
-
+ writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index,
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
return ofs;
}
-static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
+static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
- *val = readl(mv_ap_base(ap) + ofs);
+ *val = readl(mv_ap_base(link->ap) + ofs);
return 0;
} else
return -EINVAL;
}
-static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
{
unsigned int ofs = mv_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
- writelfl(val, mv_ap_base(ap) + ofs);
+ writelfl(val, mv_ap_base(link->ap) + ofs);
return 0;
} else
return -EINVAL;
if (ap->nr_active_links == 0)
return 0;
- if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) {
- /*
- * The port is operating in host queuing mode (EDMA).
- * It can accomodate a new qc if the qc protocol
- * is compatible with the current host queue mode.
- */
- if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) {
- /*
- * The host queue (EDMA) is in NCQ mode.
- * If the new qc is also an NCQ command,
- * then allow the new qc.
- */
- if (qc->tf.protocol == ATA_PROT_NCQ)
- return 0;
- } else {
- /*
- * The host queue (EDMA) is in non-NCQ, DMA mode.
- * If the new qc is also a non-NCQ, DMA command,
- * then allow the new qc.
- */
- if (qc->tf.protocol == ATA_PROT_DMA)
- return 0;
- }
- }
+ /*
+ * The port is operating in host queuing mode (EDMA) with NCQ
+ * enabled, allow multiple NCQ commands. EDMA also allows
+ * queueing multiple DMA commands but libata core currently
+ * doesn't allow it.
+ */
+ if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) &&
+ (pp->pp_flags & MV_PP_FLAG_NCQ_EN) && ata_is_ncq(qc->tf.protocol))
+ return 0;
+
return ATA_DEFER_PORT;
}
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
cfg |= (1 << 22); /* enab 4-entry host queue cache */
- if (HAS_PCI(ap->host))
+ if (!IS_SOC(hpriv))
cfg |= (1 << 18); /* enab early completion */
if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
goto out_port_free_dma_mem;
memset(pp->crpb, 0, MV_CRPB_Q_SZ);
+ /* 6041/6081 Rev. "C0" (and newer) are okay with async notify */
+ if (hpriv->hp_flags & MV_HP_ERRATA_60X1C0)
+ ap->flags |= ATA_FLAG_AN;
/*
* For GEN_I, there's no NCQ, so we only allocate a single sg_tbl.
* For later hardware, we need one unique sg_tbl per NCQ tag.
if ((qc->tf.protocol != ATA_PROT_DMA) &&
(qc->tf.protocol != ATA_PROT_NCQ)) {
+ static int limit_warnings = 10;
+ /*
+ * Errata SATA#16, SATA#24: warn if multiple DRQs expected.
+ *
+ * Someday, we might implement special polling workarounds
+ * for these, but it all seems rather unnecessary since we
+ * normally use only DMA for commands which transfer more
+ * than a single block of data.
+ *
+ * Much of the time, this could just work regardless.
+ * So for now, just log the incident, and allow the attempt.
+ */
+ if (limit_warnings > 0 && (qc->nbytes / qc->sect_size) > 1) {
+ --limit_warnings;
+ ata_link_printk(qc->dev->link, KERN_WARNING, DRV_NAME
+ ": attempting PIO w/multiple DRQ: "
+ "this may fail due to h/w errata\n");
+ }
/*
* We're about to send a non-EDMA capable command to the
* port. Turn off EDMA so there won't be problems accessing
* a bogus register value which can indicate HW removal or PCI fault.
*/
if (pending_irqs && main_irq_cause != 0xffffffffU) {
- if (unlikely((pending_irqs & PCI_ERR) && HAS_PCI(host)))
+ if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv)))
handled = mv_pci_error(host, hpriv->base);
else
handled = mv_host_intr(host, pending_irqs);
return ofs;
}
-static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
+static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_host_priv *hpriv = link->ap->host->private_data;
void __iomem *mmio = hpriv->base;
- void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
+ void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
return -EINVAL;
}
-static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
+static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val)
{
- struct mv_host_priv *hpriv = ap->host->private_data;
+ struct mv_host_priv *hpriv = link->ap->host->private_data;
void __iomem *mmio = hpriv->base;
- void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
+ void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
if (ofs != 0xffffffffU) {
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
int fix_phy_mode4 =
hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
- u32 m2, tmp;
+ u32 m2, m3;
if (fix_phy_mode2) {
m2 = readl(port_mmio + PHY_MODE2);
udelay(200);
}
- /* who knows what this magic does */
- tmp = readl(port_mmio + PHY_MODE3);
- tmp &= ~0x7F800000;
- tmp |= 0x2A800000;
- writel(tmp, port_mmio + PHY_MODE3);
-
- if (fix_phy_mode4) {
- u32 m4;
-
- m4 = readl(port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- tmp = readl(port_mmio + PHY_MODE3);
+ /*
+ * Gen-II/IIe PHY_MODE3 errata RM#2:
+ * Achieves better receiver noise performance than the h/w default:
+ */
+ m3 = readl(port_mmio + PHY_MODE3);
+ m3 = (m3 & 0x1f) | (0x5555601 << 5);
- /* workaround for errata FEr SATA#10 (part 1) */
- m4 = (m4 & ~(1 << 1)) | (1 << 0);
+ /* Guideline 88F5182 (GL# SATA-S11) */
+ if (IS_SOC(hpriv))
+ m3 &= ~0x1c;
+ if (fix_phy_mode4) {
+ u32 m4 = readl(port_mmio + PHY_MODE4);
+ /*
+ * Enforce reserved-bit restrictions on GenIIe devices only.
+ * For earlier chipsets, force only the internal config field
+ * (workaround for errata FEr SATA#10 part 1).
+ */
+ if (IS_GEN_IIE(hpriv))
+ m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES;
+ else
+ m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE;
writel(m4, port_mmio + PHY_MODE4);
-
- if (hp_flags & MV_HP_ERRATA_60X1B2)
- writel(tmp, port_mmio + PHY_MODE3);
}
+ /*
+ * Workaround for 60x1-B2 errata SATA#13:
+ * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3,
+ * so we must always rewrite PHY_MODE3 after PHY_MODE4.
+ */
+ writel(m3, port_mmio + PHY_MODE3);
/* Revert values of pre-emphasis and signal amps to the saved ones */
m2 = readl(port_mmio + PHY_MODE2);
void __iomem *mmio = hpriv->base;
u32 reg;
- if (!HAS_PCI(host) || !IS_PCIE(hpriv))
+ if (IS_SOC(hpriv) || !IS_PCIE(hpriv))
return 0; /* not PCI-X capable */
reg = readl(mmio + MV_PCI_MODE_OFS);
if ((reg & MV_PCI_MODE_MASK) == 0)
hp_flags |= MV_HP_CUT_THROUGH;
switch (pdev->revision) {
- case 0x0:
- hp_flags |= MV_HP_ERRATA_XX42A0;
- break;
- case 0x1:
+ case 0x2: /* Rev.B0: the first/only public release */
hp_flags |= MV_HP_ERRATA_60X1C0;
break;
default:
break;
case chip_soc:
hpriv->ops = &mv_soc_ops;
- hp_flags |= MV_HP_ERRATA_60X1C0;
+ hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE |
+ MV_HP_ERRATA_60X1C0;
break;
default:
if (rc)
goto done;
- if (HAS_PCI(host)) {
- hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
- hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
- } else {
+ if (IS_SOC(hpriv)) {
hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE_OFS;
hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK_OFS;
+ } else {
+ hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK_OFS;
}
/* global interrupt mask: 0 == mask everything */
mv_port_init(&ap->ioaddr, port_mmio);
#ifdef CONFIG_PCI
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
unsigned int offset = port_mmio - mmio;
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
}
- if (HAS_PCI(host)) {
+ if (!IS_SOC(hpriv)) {
/* Clear any currently outstanding host interrupt conditions */
writelfl(0, mmio + hpriv->irq_cause_ofs);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff