#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>
+#include "sis.h"
#define DRV_NAME "pata_sis"
-#define DRV_VERSION "0.4.5"
+#define DRV_VERSION "0.5.1"
struct sis_chipset {
- u16 device; /* PCI host ID */
- struct ata_port_info *info; /* Info block */
+ u16 device; /* PCI host ID */
+ const struct ata_port_info *info; /* Info block */
/* Probably add family, cable detect type etc here to clean
up code later */
};
}
/**
- * sis_port_base - return PCI configuration base for dev
+ * sis_old_port_base - return PCI configuration base for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
* number.
*/
-static int sis_port_base(struct ata_device *adev)
+static int sis_old_port_base(struct ata_device *adev)
{
return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno);
}
/**
- * sis_133_pre_reset - check for 40/80 pin
+ * sis_133_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection for the later UDMA133 capable
* SiS chipset.
*/
-static int sis_133_pre_reset(struct ata_port *ap)
+static int sis_133_cable_detect(struct ata_port *ap)
{
- static const struct pci_bits sis_enable_bits[] = {
- { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
- { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
- };
-
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 tmp;
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
- return -ENOENT;
-
/* The top bit of this register is the cable detect bit */
pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
if ((tmp & 0x8000) && !sis_short_ata40(pdev))
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA80;
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
/**
- * sis_error_handler - Probe specified port on PATA host controller
- * @ap: Port to probe
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void sis_133_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
-
-
-/**
- * sis_66_pre_reset - check for 40/80 pin
+ * sis_66_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
* SiS IDE controllers.
*/
-static int sis_66_pre_reset(struct ata_port *ap)
+static int sis_66_cable_detect(struct ata_port *ap)
{
- static const struct pci_bits sis_enable_bits[] = {
- { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
- { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
- };
-
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 tmp;
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
- return 0;
- }
/* Older chips keep cable detect in bits 4/5 of reg 0x48 */
pci_read_config_byte(pdev, 0x48, &tmp);
tmp >>= ap->port_no;
if ((tmp & 0x10) && !sis_short_ata40(pdev))
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA80;
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
-/**
- * sis_66_error_handler - Probe specified port on PATA host controller
- * @ap: Port to probe
- * @classes:
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void sis_66_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
/**
- * sis_old_pre_reset - probe begin
+ * sis_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int sis_old_pre_reset(struct ata_port *ap)
+static int sis_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
- return 0;
- }
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
+ if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ return ata_std_prereset(ap, deadline);
}
/**
- * sis_old_error_handler - Probe specified port on PATA host controller
+ * sis_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
*
* LOCKING:
* None (inherited from caller).
*/
-static void sis_old_error_handler(struct ata_port *ap)
+static void sis_error_handler(struct ata_port *ap)
{
- ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ ata_bmdma_drive_eh(ap, sis_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device, bit 15 udma */
- timing &= ~ 0x870F;
+ timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x6000;
+ timing &= ~0xF000;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
- const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+ const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+ /* Low 4 bits are timing */
+ static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82, 0x81};
- const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
-
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
u32 reg54;
/* bits 4- cycle time 8 - cvs time */
- const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
- const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
+ static const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
+ static const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
pci_read_config_dword(pdev, 0x54, ®54);
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations sis_133_ops = {
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_133_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_133_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
+
+ .port_start = ata_port_start,
+};
+
+static const struct ata_port_operations sis_133_for_sata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = sis_133_set_piomode,
+ .set_dmamode = sis_133_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_133_cable_detect,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_133_early_ops = {
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_66_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_100_ops = {
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
-
+ .cable_detect = sis_66_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_66_ops = {
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .cable_detect = sis_66_cable_detect,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_old_ops = {
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_old_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
-static struct ata_port_info sis_info = {
+static const struct ata_port_info sis_info = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = 0,
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info33 = {
+static const struct ata_port_info sis_info33 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA2, /* UDMA 33 */
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info66 = {
+static const struct ata_port_info sis_info66 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &sis_66_ops,
};
-static struct ata_port_info sis_info100 = {
+static const struct ata_port_info sis_info100 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
-static struct ata_port_info sis_info100_early = {
+static const struct ata_port_info sis_info100_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.udma_mask = ATA_UDMA5,
.pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
-static struct ata_port_info sis_info133 = {
+static const struct ata_port_info sis_info133 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
};
-static struct ata_port_info sis_info133_early = {
+const struct ata_port_info sis_info133_for_sata = {
+ .sht = &sis_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sis_133_for_sata_ops,
+};
+static const struct ata_port_info sis_info133_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
};
/* Privately shared with the SiS180 SATA driver, not for use elsewhere */
-EXPORT_SYMBOL_GPL(sis_info133);
+EXPORT_SYMBOL_GPL(sis_info133_for_sata);
static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
{
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info *port_info[2];
- struct ata_port_info *port;
+ struct ata_port_info port;
+ const struct ata_port_info *ppi[] = { &port, NULL };
struct pci_dev *host = NULL;
struct sis_chipset *chipset = NULL;
+ struct sis_chipset *sets;
static struct sis_chipset sis_chipsets[] = {
/* We have to find the bridge first */
- for (chipset = &sis_chipsets[0]; chipset->device; chipset++) {
- host = pci_get_device(PCI_VENDOR_ID_SI, chipset->device, NULL);
+ for (sets = &sis_chipsets[0]; sets->device; sets++) {
+ host = pci_get_device(PCI_VENDOR_ID_SI, sets->device, NULL);
if (host != NULL) {
- if (chipset->device == 0x630) { /* SIS630 */
+ chipset = sets; /* Match found */
+ if (sets->device == 0x630) { /* SIS630 */
u8 host_rev;
pci_read_config_byte(host, PCI_REVISION_ID, &host_rev);
if (host_rev >= 0x30) /* 630 ET */
}
/* Look for concealed bridges */
- if (host == NULL) {
+ if (chipset == NULL) {
/* Second check */
u32 idemisc;
u16 trueid;
if (chipset == NULL)
return -ENODEV;
- port = chipset->info;
- port->private_data = chipset;
+ port = *chipset->info;
+ port.private_data = chipset;
sis_fixup(pdev, chipset);
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
{ PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
+ { PCI_VDEVICE(SI, 0x1180), }, /* SiS 1180 */
{ }
};
.id_table = sis_pci_tbl,
.probe = sis_init_one,
.remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
+#endif
};
static int __init sis_init(void)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff