#include <linux/libata.h>
#define DRV_NAME "pata_pdc2027x"
-#define DRV_VERSION "0.74-ac5"
+#define DRV_VERSION "1.0"
#undef PDC_DEBUG
#ifdef PDC_DEBUG
-#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#else
#define PDPRINTK(fmt, args...)
#endif
};
static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
-static void pdc2027x_error_handler(struct ata_port *ap);
+static int pdc2027x_prereset(struct ata_link *link, unsigned long deadline);
static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev);
static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev);
-static void pdc2027x_post_set_mode(struct ata_port *ap);
static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc);
+static unsigned long pdc2027x_mode_filter(struct ata_device *adev, unsigned long mask);
+static int pdc2027x_cable_detect(struct ata_port *ap);
+static int pdc2027x_set_mode(struct ata_link *link, struct ata_device **r_failed);
/*
* ATA Timing Tables based on 133MHz controller clock.
};
static struct scsi_host_template pdc2027x_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations pdc2027x_pata100_ops = {
- .port_disable = ata_port_disable,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
+ .inherits = &ata_bmdma_port_ops,
.check_atapi_dma = pdc2027x_check_atapi_dma,
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_data_xfer,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = pdc2027x_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
+ .cable_detect = pdc2027x_cable_detect,
+ .prereset = pdc2027x_prereset,
};
static struct ata_port_operations pdc2027x_pata133_ops = {
- .port_disable = ata_port_disable,
+ .inherits = &pdc2027x_pata100_ops,
+ .mode_filter = pdc2027x_mode_filter,
.set_piomode = pdc2027x_set_piomode,
.set_dmamode = pdc2027x_set_dmamode,
- .post_set_mode = pdc2027x_post_set_mode,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .check_atapi_dma = pdc2027x_check_atapi_dma,
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_data_xfer,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = pdc2027x_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
+ .set_mode = pdc2027x_set_mode,
};
static struct ata_port_info pdc2027x_port_info[] = {
/* PDC_UDMA_100 */
{
- .sht = &pdc2027x_sht,
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA5, /* udma0-5 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &pdc2027x_pata100_ops,
},
/* PDC_UDMA_133 */
{
- .sht = &pdc2027x_sht,
.flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
ATA_FLAG_MMIO,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = ATA_UDMA6, /* udma0-6 */
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &pdc2027x_pata133_ops,
},
};
}
/**
- * pdc2027x_pata_cbl_detect - Probe host controller cable detect info
+ * pdc2027x_pata_cable_detect - Probe host controller cable detect info
* @ap: Port for which cable detect info is desired
*
* Read 80c cable indicator from Promise extended register.
* LOCKING:
* None (inherited from caller).
*/
-static void pdc2027x_cbl_detect(struct ata_port *ap)
+static int pdc2027x_cable_detect(struct ata_port *ap)
{
u32 cgcr;
/* check cable detect results */
- cgcr = readl(port_mmio(ap, PDC_GLOBAL_CTL));
+ cgcr = ioread32(port_mmio(ap, PDC_GLOBAL_CTL));
if (cgcr & (1 << 26))
goto cbl40;
PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no);
- ap->cbl = ATA_CBL_PATA80;
- return;
-
+ return ATA_CBL_PATA80;
cbl40:
printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no);
- ap->cbl = ATA_CBL_PATA40;
- ap->udma_mask &= ATA_UDMA_MASK_40C;
+ return ATA_CBL_PATA40;
}
/**
*/
static inline int pdc2027x_port_enabled(struct ata_port *ap)
{
- return readb(port_mmio(ap, PDC_ATA_CTL)) & 0x02;
+ return ioread8(port_mmio(ap, PDC_ATA_CTL)) & 0x02;
}
/**
* pdc2027x_prereset - prereset for PATA host controller
- * @ap: Target port
+ * @link: Target link
+ * @deadline: deadline jiffies for the operation
*
* Probeinit including cable detection.
*
* None (inherited from caller).
*/
-static int pdc2027x_prereset(struct ata_port *ap)
+static int pdc2027x_prereset(struct ata_link *link, unsigned long deadline)
{
/* Check whether port enabled */
- if (!pdc2027x_port_enabled(ap))
+ if (!pdc2027x_port_enabled(link->ap))
return -ENOENT;
- pdc2027x_cbl_detect(ap);
- return ata_std_prereset(ap);
+ return ata_sff_prereset(link, deadline);
}
/**
- * pdc2027x_error_handler - Perform reset on PATA port and classify
- * @ap: Port to reset
- *
- * Reset PATA phy and classify attached devices.
+ * pdc2720x_mode_filter - mode selection filter
+ * @adev: ATA device
+ * @mask: list of modes proposed
*
- * LOCKING:
- * None (inherited from caller).
+ * Block UDMA on devices that cause trouble with this controller.
*/
-static void pdc2027x_error_handler(struct ata_port *ap)
+static unsigned long pdc2027x_mode_filter(struct ata_device *adev, unsigned long mask)
{
- ata_bmdma_drive_eh(ap, pdc2027x_prereset, ata_std_softreset, NULL, ata_std_postreset);
+ unsigned char model_num[ATA_ID_PROD_LEN + 1];
+ struct ata_device *pair = ata_dev_pair(adev);
+
+ if (adev->class != ATA_DEV_ATA || adev->devno == 0 || pair == NULL)
+ return ata_bmdma_mode_filter(adev, mask);
+
+ /* Check for slave of a Maxtor at UDMA6 */
+ ata_id_c_string(pair->id, model_num, ATA_ID_PROD,
+ ATA_ID_PROD_LEN + 1);
+ /* If the master is a maxtor in UDMA6 then the slave should not use UDMA 6 */
+ if (strstr(model_num, "Maxtor") == NULL && pair->dma_mode == XFER_UDMA_6)
+ mask &= ~ (1 << (6 + ATA_SHIFT_UDMA));
+
+ return ata_bmdma_mode_filter(adev, mask);
}
/**
* pdc2027x_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port to configure
* @adev: um
- * @pio: PIO mode, 0 - 4
*
* Set PIO mode for device.
*
/* Set the PIO timing registers using value table for 133MHz */
PDPRINTK("Set pio regs... \n");
- ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+ ctcr0 = ioread32(dev_mmio(ap, adev, PDC_CTCR0));
ctcr0 &= 0xffff0000;
ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 |
(pdc2027x_pio_timing_tbl[pio].value1 << 8);
- writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+ iowrite32(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
- ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+ ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1));
ctcr1 &= 0x00ffffff;
ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24);
- writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+ iowrite32(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
PDPRINTK("Set pio regs done\n");
* pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings
* @ap: Port to configure
* @adev: um
- * @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6
*
* Set UDMA mode for device.
*
* If tHOLD is '1', the hardware will add half clock for data hold time.
* This code segment seems to be no effect. tHOLD will be overwritten below.
*/
- ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
- writel(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1));
+ ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1));
+ iowrite32(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1));
}
PDPRINTK("Set udma regs... \n");
- ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1));
+ ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1));
ctcr1 &= 0xff000000;
ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 |
(pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) |
(pdc2027x_udma_timing_tbl[udma_mode].value2 << 16);
- writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
+ iowrite32(ctcr1, dev_mmio(ap, adev, PDC_CTCR1));
PDPRINTK("Set udma regs done\n");
unsigned int mdma_mode = dma_mode & 0x07;
PDPRINTK("Set mdma regs... \n");
- ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0));
+ ctcr0 = ioread32(dev_mmio(ap, adev, PDC_CTCR0));
ctcr0 &= 0x0000ffff;
ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) |
(pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24);
- writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
+ iowrite32(ctcr0, dev_mmio(ap, adev, PDC_CTCR0));
PDPRINTK("Set mdma regs done\n");
PDPRINTK("Set to mdma mode[%u] \n", mdma_mode);
}
/**
- * pdc2027x_post_set_mode - Set the timing registers back to correct values.
- * @ap: Port to configure
+ * pdc2027x_set_mode - Set the timing registers back to correct values.
+ * @link: link to configure
+ * @r_failed: Returned device for failure
*
* The pdc2027x hardware will look at "SET FEATURES" and change the timing registers
* automatically. The values set by the hardware might be incorrect, under 133Mhz PLL.
* This function overwrites the possibly incorrect values set by the hardware to be correct.
*/
-static void pdc2027x_post_set_mode(struct ata_port *ap)
+static int pdc2027x_set_mode(struct ata_link *link, struct ata_device **r_failed)
{
- int i;
+ struct ata_port *ap = link->ap;
+ struct ata_device *dev;
+ int rc;
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- struct ata_device *dev = &ap->device[i];
+ rc = ata_do_set_mode(link, r_failed);
+ if (rc < 0)
+ return rc;
- if (ata_dev_enabled(dev)) {
+ ata_for_each_dev(dev, link, ENABLED) {
+ pdc2027x_set_piomode(ap, dev);
- pdc2027x_set_piomode(ap, dev);
+ /*
+ * Enable prefetch if the device support PIO only.
+ */
+ if (dev->xfer_shift == ATA_SHIFT_PIO) {
+ u32 ctcr1 = ioread32(dev_mmio(ap, dev, PDC_CTCR1));
+ ctcr1 |= (1 << 25);
+ iowrite32(ctcr1, dev_mmio(ap, dev, PDC_CTCR1));
- /*
- * Enable prefetch if the device support PIO only.
- */
- if (dev->xfer_shift == ATA_SHIFT_PIO) {
- u32 ctcr1 = readl(dev_mmio(ap, dev, PDC_CTCR1));
- ctcr1 |= (1 << 25);
- writel(ctcr1, dev_mmio(ap, dev, PDC_CTCR1));
-
- PDPRINTK("Turn on prefetch\n");
- } else {
- pdc2027x_set_dmamode(ap, dev);
- }
+ PDPRINTK("Turn on prefetch\n");
+ } else {
+ pdc2027x_set_dmamode(ap, dev);
}
}
+ return 0;
}
/**
/**
* pdc_read_counter - Read the ctr counter
- * @probe_ent: for the port address
+ * @host: target ATA host
*/
-static long pdc_read_counter(struct ata_probe_ent *probe_ent)
+static long pdc_read_counter(struct ata_host *host)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
long counter;
int retry = 1;
u32 bccrl, bccrh, bccrlv, bccrhv;
retry:
- bccrl = readl(mmio_base + PDC_BYTE_COUNT) & 0xffff;
- bccrh = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
- rmb();
+ bccrl = ioread32(mmio_base + PDC_BYTE_COUNT) & 0x7fff;
+ bccrh = ioread32(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff;
/* Read the counter values again for verification */
- bccrlv = readl(mmio_base + PDC_BYTE_COUNT) & 0xffff;
- bccrhv = readl(mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff;
- rmb();
+ bccrlv = ioread32(mmio_base + PDC_BYTE_COUNT) & 0x7fff;
+ bccrhv = ioread32(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff;
counter = (bccrh << 15) | bccrl;
* adjust_pll - Adjust the PLL input clock in Hz.
*
* @pdc_controller: controller specific information
- * @probe_ent: For the port address
+ * @host: target ATA host
* @pll_clock: The input of PLL in HZ
*/
-static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx)
+static void pdc_adjust_pll(struct ata_host *host, long pll_clock, unsigned int board_idx)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
u16 pll_ctl;
long pll_clock_khz = pll_clock / 1000;
long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ;
/* Show the current clock value of PLL control register
* (maybe already configured by the firmware)
*/
- pll_ctl = readw(mmio_base + PDC_PLL_CTL);
+ pll_ctl = ioread16(mmio_base + PDC_PLL_CTL);
PDPRINTK("pll_ctl[%X]\n", pll_ctl);
#endif
PDPRINTK("Writing pll_ctl[%X]\n", pll_ctl);
- writew(pll_ctl, mmio_base + PDC_PLL_CTL);
- readw(mmio_base + PDC_PLL_CTL); /* flush */
+ iowrite16(pll_ctl, mmio_base + PDC_PLL_CTL);
+ ioread16(mmio_base + PDC_PLL_CTL); /* flush */
/* Wait the PLL circuit to be stable */
mdelay(30);
* Show the current clock value of PLL control register
* (maybe configured by the firmware)
*/
- pll_ctl = readw(mmio_base + PDC_PLL_CTL);
+ pll_ctl = ioread16(mmio_base + PDC_PLL_CTL);
PDPRINTK("pll_ctl[%X]\n", pll_ctl);
#endif
/**
* detect_pll_input_clock - Detect the PLL input clock in Hz.
- * @probe_ent: for the port address
+ * @host: target ATA host
* Ex. 16949000 on 33MHz PCI bus for pdc20275.
* Half of the PCI clock.
*/
-static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent)
+static long pdc_detect_pll_input_clock(struct ata_host *host)
{
- void __iomem *mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR];
u32 scr;
long start_count, end_count;
- long pll_clock;
-
- /* Read current counter value */
- start_count = pdc_read_counter(probe_ent);
+ struct timeval start_time, end_time;
+ long pll_clock, usec_elapsed;
/* Start the test mode */
- scr = readl(mmio_base + PDC_SYS_CTL);
+ scr = ioread32(mmio_base + PDC_SYS_CTL);
PDPRINTK("scr[%X]\n", scr);
- writel(scr | (0x01 << 14), mmio_base + PDC_SYS_CTL);
- readl(mmio_base + PDC_SYS_CTL); /* flush */
+ iowrite32(scr | (0x01 << 14), mmio_base + PDC_SYS_CTL);
+ ioread32(mmio_base + PDC_SYS_CTL); /* flush */
+
+ /* Read current counter value */
+ start_count = pdc_read_counter(host);
+ do_gettimeofday(&start_time);
/* Let the counter run for 100 ms. */
mdelay(100);
/* Read the counter values again */
- end_count = pdc_read_counter(probe_ent);
+ end_count = pdc_read_counter(host);
+ do_gettimeofday(&end_time);
/* Stop the test mode */
- scr = readl(mmio_base + PDC_SYS_CTL);
+ scr = ioread32(mmio_base + PDC_SYS_CTL);
PDPRINTK("scr[%X]\n", scr);
- writel(scr & ~(0x01 << 14), mmio_base + PDC_SYS_CTL);
- readl(mmio_base + PDC_SYS_CTL); /* flush */
+ iowrite32(scr & ~(0x01 << 14), mmio_base + PDC_SYS_CTL);
+ ioread32(mmio_base + PDC_SYS_CTL); /* flush */
/* calculate the input clock in Hz */
- pll_clock = (start_count - end_count) * 10;
+ usec_elapsed = (end_time.tv_sec - start_time.tv_sec) * 1000000 +
+ (end_time.tv_usec - start_time.tv_usec);
+
+ pll_clock = ((start_count - end_count) & 0x3fffffff) / 100 *
+ (100000000 / usec_elapsed);
PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count);
PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);
/**
* pdc_hardware_init - Initialize the hardware.
- * @pdev: instance of pci_dev found
- * @pdc_controller: controller specific information
- * @pe: for the port address
+ * @host: target ATA host
+ * @board_idx: board identifier
*/
-static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx)
+static int pdc_hardware_init(struct ata_host *host, unsigned int board_idx)
{
long pll_clock;
* Ex. 25MHz or 40MHz, we have to adjust the cycle_time.
* The pdc20275 controller employs PLL circuit to help correct timing registers setting.
*/
- pll_clock = pdc_detect_pll_input_clock(pe);
-
- if (pll_clock < 0) /* counter overflow? Try again. */
- pll_clock = pdc_detect_pll_input_clock(pe);
+ pll_clock = pdc_detect_pll_input_clock(host);
- dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
+ dev_printk(KERN_INFO, host->dev, "PLL input clock %ld kHz\n", pll_clock/1000);
/* Adjust PLL control register */
- pdc_adjust_pll(pe, pll_clock, board_idx);
+ pdc_adjust_pll(host, pll_clock, board_idx);
return 0;
}
* Called when an instance of PCI adapter is inserted.
* This function checks whether the hardware is supported,
* initialize hardware and register an instance of ata_host to
- * libata by providing struct ata_probe_ent and ata_device_add().
- * (implements struct pci_driver.probe() )
+ * libata. (implements struct pci_driver.probe() )
*
* @pdev: instance of pci_dev found
* @ent: matching entry in the id_tbl[]
static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
+ static const unsigned long cmd_offset[] = { 0x17c0, 0x15c0 };
+ static const unsigned long bmdma_offset[] = { 0x1000, 0x1008 };
unsigned int board_idx = (unsigned int) ent->driver_data;
-
- struct ata_probe_ent *probe_ent;
+ const struct ata_port_info *ppi[] =
+ { &pdc2027x_port_info[board_idx], NULL };
+ struct ata_host *host;
void __iomem *mmio_base;
- int rc;
+ int i, rc;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
+ /* alloc host */
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+
+ /* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
rc = pcim_iomap_regions(pdev, 1 << PDC_MMIO_BAR, DRV_NAME);
if (rc)
return rc;
+ host->iomap = pcim_iomap_table(pdev);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
if (rc)
return rc;
- /* Prepare the probe entry */
- probe_ent = devm_kzalloc(&pdev->dev, sizeof(*probe_ent), GFP_KERNEL);
- if (probe_ent == NULL)
- return -ENOMEM;
-
- probe_ent->dev = pci_dev_to_dev(pdev);
- INIT_LIST_HEAD(&probe_ent->node);
-
- probe_ent->sht = pdc2027x_port_info[board_idx].sht;
- probe_ent->port_flags = pdc2027x_port_info[board_idx].flags;
- probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask;
- probe_ent->mwdma_mask = pdc2027x_port_info[board_idx].mwdma_mask;
- probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask;
- probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops;
-
- probe_ent->irq = pdev->irq;
- probe_ent->irq_flags = SA_SHIRQ;
- probe_ent->iomap = pcim_iomap_table(pdev);
+ mmio_base = host->iomap[PDC_MMIO_BAR];
- mmio_base = probe_ent->iomap[PDC_MMIO_BAR];
+ for (i = 0; i < 2; i++) {
+ struct ata_port *ap = host->ports[i];
- pdc_ata_setup_port(&probe_ent->port[0], mmio_base + 0x17c0);
- probe_ent->port[0].bmdma_addr = mmio_base + 0x1000;
- pdc_ata_setup_port(&probe_ent->port[1], mmio_base + 0x15c0);
- probe_ent->port[1].bmdma_addr = mmio_base + 0x1008;
+ pdc_ata_setup_port(&ap->ioaddr, mmio_base + cmd_offset[i]);
+ ap->ioaddr.bmdma_addr = mmio_base + bmdma_offset[i];
- probe_ent->n_ports = 2;
+ ata_port_pbar_desc(ap, PDC_MMIO_BAR, -1, "mmio");
+ ata_port_pbar_desc(ap, PDC_MMIO_BAR, cmd_offset[i], "cmd");
+ }
- pci_set_master(pdev);
//pci_enable_intx(pdev);
/* initialize adapter */
- if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0)
+ if (pdc_hardware_init(host, board_idx) != 0)
return -EIO;
- if (!ata_device_add(probe_ent))
- return -ENODEV;
-
- devm_kfree(&pdev->dev, probe_ent);
- return 0;
+ pci_set_master(pdev);
+ return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
+ IRQF_SHARED, &pdc2027x_sht);
}
/**