/*
* pata_mpiix.c - Intel MPIIX PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
*
* The MPIIX is different enough to the PIIX4 and friends that we give it
* a separate driver. The old ide/pci code handles this by just not tuning
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
-#define DRV_VERSION "0.7.6"
+#define DRV_VERSION "0.7.7"
enum {
IDETIM = 0x6C, /* IDE control register */
SECONDARY = (1 << 14)
};
-static int mpiix_pre_reset(struct ata_port *ap)
+static int mpiix_pre_reset(struct ata_link *link, unsigned long deadline)
{
+ struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
return -ENOENT;
- return ata_std_prereset(ap);
-}
-
-/**
- * mpiix_error_handler - probe reset
- * @ap: ATA port
- *
- * Perform the ATA probe and bus reset sequence plus specific handling
- * for this hardware. The MPIIX has the enable bits in a different place
- * to PIIX4 and friends. As a pure PIO device it has no cable detect
- */
-static void mpiix_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, mpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ return ata_sff_prereset(link, deadline);
}
/**
*
* This would get very ugly because we can only program timing for one
* device at a time, the other gets PIO0. Fortunately libata calls
- * our qc_issue_prot command before a command is issued so we can
- * flip the timings back and forth to reduce the pain.
+ * our qc_issue command before a command is issued so we can flip the
+ * timings back and forth to reduce the pain.
*/
static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
}
/**
- * mpiix_qc_issue_prot - command issue
+ * mpiix_qc_issue - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
- * neccessary. Our logic also clears TIME0/TIME1 for the other device so
+ * necessary. Our logic also clears TIME0/TIME1 for the other device so
* that, even if we get this wrong, cycles to the other device will
* be made PIO0.
*/
-static unsigned int mpiix_qc_issue_prot(struct ata_queued_cmd *qc)
+static unsigned int mpiix_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
if (adev->pio_mode && adev != ap->private_data)
mpiix_set_piomode(ap, adev);
- return ata_qc_issue_prot(qc);
+ return ata_sff_qc_issue(qc);
}
static struct scsi_host_template mpiix_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
+ ATA_PIO_SHT(DRV_NAME),
};
static struct ata_port_operations mpiix_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = mpiix_set_piomode,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = mpiix_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .inherits = &ata_sff_port_ops,
+ .qc_issue = mpiix_qc_issue,
.cable_detect = ata_cable_40wire,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = mpiix_qc_issue_prot,
- .data_xfer = ata_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
- .irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
-
- .port_start = ata_port_start,
+ .set_piomode = mpiix_set_piomode,
+ .prereset = mpiix_pre_reset,
+ .sff_data_xfer = ata_sff_data_xfer32,
};
static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* Single threaded by the PCI probe logic */
- static struct ata_probe_ent probe;
static int printed_version;
+ struct ata_host *host;
+ struct ata_port *ap;
void __iomem *cmd_addr, *ctl_addr;
u16 idetim;
- int irq;
+ int cmd, ctl, irq;
if (!printed_version++)
dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
+ host = ata_host_alloc(&dev->dev, 1);
+ if (!host)
+ return -ENOMEM;
+ ap = host->ports[0];
+
/* MPIIX has many functions which can be turned on or off according
to other devices present. Make sure IDE is enabled before we try
and use it */
/* See if it's primary or secondary channel... */
if (!(idetim & SECONDARY)) {
+ cmd = 0x1F0;
+ ctl = 0x3F6;
irq = 14;
- cmd_addr = devm_ioport_map(&dev->dev, 0x1F0, 8);
- ctl_addr = devm_ioport_map(&dev->dev, 0x3F6, 1);
} else {
+ cmd = 0x170;
+ ctl = 0x376;
irq = 15;
- cmd_addr = devm_ioport_map(&dev->dev, 0x170, 8);
- ctl_addr = devm_ioport_map(&dev->dev, 0x376, 1);
}
+ cmd_addr = devm_ioport_map(&dev->dev, cmd, 8);
+ ctl_addr = devm_ioport_map(&dev->dev, ctl, 1);
if (!cmd_addr || !ctl_addr)
return -ENOMEM;
+ ata_port_desc(ap, "cmd 0x%x ctl 0x%x", cmd, ctl);
+
/* We do our own plumbing to avoid leaking special cases for whacko
ancient hardware into the core code. There are two issues to
worry about. #1 The chip is a bridge so if in legacy mode and
without BARs set fools the setup. #2 If you pci_disable_device
the MPIIX your box goes castors up */
- INIT_LIST_HEAD(&probe.node);
- probe.dev = pci_dev_to_dev(dev);
- probe.port_ops = &mpiix_port_ops;
- probe.sht = &mpiix_sht;
- probe.pio_mask = 0x1F;
- probe.irq_flags = IRQF_SHARED;
- probe.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST;
- probe.n_ports = 1;
+ ap->ops = &mpiix_port_ops;
+ ap->pio_mask = ATA_PIO4;
+ ap->flags |= ATA_FLAG_SLAVE_POSS;
- probe.irq = irq;
- probe.port[0].cmd_addr = cmd_addr;
- probe.port[0].ctl_addr = ctl_addr;
- probe.port[0].altstatus_addr = ctl_addr;
+ ap->ioaddr.cmd_addr = cmd_addr;
+ ap->ioaddr.ctl_addr = ctl_addr;
+ ap->ioaddr.altstatus_addr = ctl_addr;
/* Let libata fill in the port details */
- ata_std_ports(&probe.port[0]);
+ ata_sff_std_ports(&ap->ioaddr);
- /* Now add the port that is active */
- if (ata_device_add(&probe))
- return 0;
- return -ENODEV;
+ /* activate host */
+ return ata_host_activate(host, irq, ata_sff_interrupt, IRQF_SHARED,
+ &mpiix_sht);
}
static const struct pci_device_id mpiix[] = {
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff