/*
* pata_it821x.c - IT821x PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
+ * Alan Cox <alan@lxorguk.ukuu.org.uk>
* (C) 2007 Bartlomiej Zolnierkiewicz
*
* based upon
*
* linux/drivers/ide/pci/it821x.c Version 0.09 December 2004
*
- * Copyright (C) 2004 Red Hat <alan@redhat.com>
+ * Copyright (C) 2004 Red Hat
*
* May be copied or modified under the terms of the GNU General Public License
* Based in part on the ITE vendor provided SCSI driver.
#define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.4.0"
+#define DRV_VERSION "0.4.2"
struct it821x_dev
{
{
struct ata_device *dev;
- ata_link_for_each_dev(dev, link) {
- if (ata_dev_enabled(dev)) {
- /* We don't really care */
- dev->pio_mode = XFER_PIO_0;
- dev->dma_mode = XFER_MW_DMA_0;
- /* We do need the right mode information for DMA or PIO
- and this comes from the current configuration flags */
- if (ata_id_has_dma(dev->id)) {
- ata_dev_printk(dev, KERN_INFO, "configured for DMA\n");
- dev->xfer_mode = XFER_MW_DMA_0;
- dev->xfer_shift = ATA_SHIFT_MWDMA;
- dev->flags &= ~ATA_DFLAG_PIO;
- } else {
- ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
- dev->xfer_mode = XFER_PIO_0;
- dev->xfer_shift = ATA_SHIFT_PIO;
- dev->flags |= ATA_DFLAG_PIO;
- }
+ ata_for_each_dev(dev, link, ENABLED) {
+ /* We don't really care */
+ dev->pio_mode = XFER_PIO_0;
+ dev->dma_mode = XFER_MW_DMA_0;
+ /* We do need the right mode information for DMA or PIO
+ and this comes from the current configuration flags */
+ if (ata_id_has_dma(dev->id)) {
+ ata_dev_printk(dev, KERN_INFO, "configured for DMA\n");
+ dev->xfer_mode = XFER_MW_DMA_0;
+ dev->xfer_shift = ATA_SHIFT_MWDMA;
+ dev->flags &= ~ATA_DFLAG_PIO;
+ } else {
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
+ dev->xfer_mode = XFER_PIO_0;
+ dev->xfer_shift = ATA_SHIFT_PIO;
+ dev->flags |= ATA_DFLAG_PIO;
}
}
return 0;
* special. In our case we need to lock the sector count to avoid
* blowing the brains out of the firmware with large LBA48 requests
*
- * FIXME: When FUA appears we need to block FUA too. And SMART and
- * basically we need to filter commands for this chip.
*/
static void it821x_dev_config(struct ata_device *adev)
if (strstr(model_num, "Integrated Technology Express")) {
/* Set feature bits the firmware neglects */
id[49] |= 0x0300; /* LBA, DMA */
- id[82] |= 0x0400; /* LBA48 */
id[83] &= 0x7FFF;
- id[83] |= 0x4000; /* Word 83 is valid */
+ id[83] |= 0x4400; /* Word 83 is valid and LBA48 */
id[86] |= 0x0400; /* LBA48 on */
id[ATA_ID_MAJOR_VER] |= 0x1F;
}
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &it821x_rdc_port_ops
+ };
+ static const struct ata_port_info info_rdc_11 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
/* No UDMA */
.port_ops = &it821x_rdc_port_ops
};
return rc;
if (pdev->vendor == PCI_VENDOR_ID_RDC) {
- ppi[0] = &info_rdc;
+ /* Deal with Vortex86SX */
+ if (pdev->revision == 0x11)
+ ppi[0] = &info_rdc_11;
+ else
+ ppi[0] = &info_rdc;
} else {
/* Force the card into bypass mode if so requested */
if (it8212_noraid) {