* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
*
*
* TODO
- * 371N
* Work out best PLL policy
*/
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.3"
+#define DRV_VERSION "0.3.4"
enum {
HPT_PCI_FAST = (1 << 31),
/**
* hpt3x2n_pre_reset - reset the hpt3x2n bus
- * @ap: ATA port to reset
+ * @link: ATA link to reset
+ * @deadline: deadline jiffies for the operation
*
* Perform the initial reset handling for the 3x2n series controllers.
* Reset the hardware and state machine,
*/
-static int hpt3xn_pre_reset(struct ata_port *ap)
+static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
{
+ struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Reset the state machine */
- pci_write_config_byte(pdev, 0x50, 0x37);
- pci_write_config_byte(pdev, 0x54, 0x37);
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
- return ata_std_prereset(ap);
-}
-
-/**
- * hpt3x2n_error_handler - probe the hpt3x2n bus
- * @ap: ATA port to reset
- *
- * Perform the probe reset handling for the 3x2N
- */
-static void hpt3x2n_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ return ata_sff_prereset(link, deadline);
}
/**
return 0;
}
-static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
+static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_taskfile *tf = &qc->tf;
struct ata_port *ap = qc->ap;
hpt3x2n_set_clock(ap, 0x23);
}
}
- return ata_qc_issue_prot(qc);
+ return ata_sff_qc_issue(qc);
}
static struct scsi_host_template hpt3x2n_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ ATA_BMDMA_SHT(DRV_NAME),
};
/*
*/
static struct ata_port_operations hpt3x2n_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = hpt3x2n_set_piomode,
- .set_dmamode = hpt3x2n_set_dmamode,
- .mode_filter = ata_pci_default_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = hpt3x2n_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
- .cable_detect = hpt3x2n_cable_detect,
+ .inherits = &ata_bmdma_port_ops,
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
.bmdma_stop = hpt3x2n_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = hpt3x2n_qc_issue_prot,
-
- .data_xfer = ata_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
- .irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
+ .qc_issue = hpt3x2n_qc_issue,
- .port_start = ata_port_start,
+ .cable_detect = hpt3x2n_cable_detect,
+ .set_piomode = hpt3x2n_set_piomode,
+ .set_dmamode = hpt3x2n_set_dmamode,
+ .prereset = hpt3x2n_pre_reset,
};
/**
{
unsigned long freq;
u32 fcnt;
+ unsigned long iobase = pci_resource_start(pdev, 4);
- pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+ fcnt = inl(iobase + 0x90); /* Not PCI readable for some chips */
if ((fcnt >> 12) != 0xABCDE) {
printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
return 33; /* Not BIOS set */
static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT372N and friends - UDMA133 */
- static struct ata_port_info info = {
- .sht = &hpt3x2n_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ static const struct ata_port_info info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ .udma_mask = ATA_UDMA6,
.port_ops = &hpt3x2n_port_ops
};
- struct ata_port_info *port_info[2];
- struct ata_port_info *port = &info;
+ const struct ata_port_info *ppi[] = { &info, NULL };
u8 irqmask;
u32 class_rev;
unsigned int pci_mhz;
unsigned int f_low, f_high;
int adjust;
+ unsigned long iobase = pci_resource_start(dev, 4);
+ void *hpriv = NULL;
+ int rc;
+
+ rc = pcim_enable_device(dev);
+ if (rc)
+ return rc;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
if (class_rev < 6)
return -ENODEV;
break;
+ case PCI_DEVICE_ID_TTI_HPT371:
+ if (class_rev < 2)
+ return -ENODEV;
+ /* 371N if rev > 1 */
+ break;
case PCI_DEVICE_ID_TTI_HPT372:
- /* 372N if rev >= 1*/
- if (class_rev == 0)
+ /* 372N if rev >= 2*/
+ if (class_rev < 2)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT302:
irqmask &= ~0x10;
pci_write_config_byte(dev, 0x5a, irqmask);
+ /*
+ * HPT371 chips physically have only one channel, the secondary one,
+ * but the primary channel registers do exist! Go figure...
+ * So, we manually disable the non-existing channel here
+ * (if the BIOS hasn't done this already).
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
+ u8 mcr1;
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ mcr1 &= ~0x04;
+ pci_write_config_byte(dev, 0x50, mcr1);
+ }
+
/* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
50 for UDMA100. Right now we always use 66 */
break;
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
- if (adjust == 8)
- printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+ if (adjust == 8) {
+ printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
+ return -ENODEV;
+ }
+ printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
+ pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
- port->private_data = NULL;
- if (pci_mhz > 60)
- port->private_data = (void *)PCI66;
+ if (pci_mhz > 60) {
+ hpriv = (void *)PCI66;
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+ outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
+ }
/* Now kick off ATA set up */
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv);
}
static const struct pci_device_id hpt3x2n[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff