* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
- * Portions Copyright (C) 2005-2007 MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
*
* TODO
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.7"
+#define DRV_VERSION "0.3.10"
enum {
HPT_PCI_FAST = (1 << 31),
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 FIFO enable. Only for PIO.
*/
/* 66MHz DPLL clocks */
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt3x2n_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt3x2n_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, ®);
- mode = hpt3x2n_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt3x2n_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt3x2n_set_mode(ap, adev, adev->pio_mode);
}
/**
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt3x2n_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt3x2n_set_mode(ap, adev, adev->dma_mode);
}
/**
static void hpt3x2n_set_clock(struct ata_port *ap, int source)
{
- void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+ void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8;
/* Tristate the bus */
iowrite8(0x80, bmdma+0x73);
iowrite8(source, bmdma+0x7B);
iowrite8(0xC0, bmdma+0x79);
- /* Reset state machines */
- iowrite8(0x37, bmdma+0x70);
- iowrite8(0x37, bmdma+0x74);
+ /* Reset state machines, avoid enabling the disabled channels */
+ iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70);
+ iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74);
/* Complete reset */
iowrite8(0x00, bmdma+0x79);
iowrite8(0x00, bmdma+0x77);
}
-/* Check if our partner interface is busy */
-
-static int hpt3x2n_pair_idle(struct ata_port *ap)
-{
- struct ata_host *host = ap->host;
- struct ata_port *pair = host->ports[ap->port_no ^ 1];
-
- if (pair->hsm_task_state == HSM_ST_IDLE)
- return 1;
- return 0;
-}
-
static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
{
long flags = (long)ap->host->private_data;
+
/* See if we should use the DPLL */
if (writing)
return USE_DPLL; /* Needed for write */
return 0;
}
+static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ata_port *alt = ap->host->ports[ap->port_no ^ 1];
+ int rc, flags = (long)ap->host->private_data;
+ int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ if ((flags & USE_DPLL) != dpll && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
{
- struct ata_taskfile *tf = &qc->tf;
struct ata_port *ap = qc->ap;
int flags = (long)ap->host->private_data;
+ int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
- if (hpt3x2n_pair_idle(ap)) {
- int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
- if ((flags & USE_DPLL) != dpll) {
- if (dpll == 1)
- hpt3x2n_set_clock(ap, 0x21);
- else
- hpt3x2n_set_clock(ap, 0x23);
- }
+ if ((flags & USE_DPLL) != dpll) {
+ flags &= ~USE_DPLL;
+ flags |= dpll;
+ ap->host->private_data = (void *)(long)flags;
+
+ hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23);
}
- return ata_sff_qc_issue(qc);
+ return ata_bmdma_qc_issue(qc);
}
static struct scsi_host_template hpt3x2n_sht = {
.inherits = &ata_bmdma_port_ops,
.bmdma_stop = hpt3x2n_bmdma_stop,
+
+ .qc_defer = hpt3x2n_qc_defer,
.qc_issue = hpt3x2n_qc_issue,
.cable_detect = hpt3x2n_cable_detect,
unsigned int f_low, f_high;
int adjust;
unsigned long iobase = pci_resource_start(dev, 4);
- void *hpriv = NULL;
+ void *hpriv = (void *)USE_DPLL;
int rc;
rc = pcim_enable_device(dev);
pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
- if (pci_mhz > 60) {
- hpriv = (void *)PCI66;
- /*
- * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
- * the MISC. register to stretch the UltraDMA Tss timing.
- * NOTE: This register is only writeable via I/O space.
- */
- if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
- outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
- }
+ if (pci_mhz > 60)
+ hpriv = (void *)(PCI66 | USE_DPLL);
+
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+ outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv);
+ return ata_pci_bmdma_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
}
static const struct pci_device_id hpt3x2n[] = {
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff