* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
* TODO
- * PLL mode
- * Look into engine reset on timeout errors. Should not be
- * required.
+ * Look into engine reset on timeout errors. Should not be required.
*/
#include <linux/kernel.h>
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.5.2"
+#define DRV_VERSION "0.6.14"
struct hpt_clock {
u8 xfer_speed;
* 31 FIFO enable.
*/
-/* from highpoint documentation. these are old values */
-static const struct hpt_clock hpt370_timings_33[] = {
-/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */
- { XFER_UDMA_5, 0x16454e31 },
- { XFER_UDMA_4, 0x16454e31 },
- { XFER_UDMA_3, 0x166d4e31 },
- { XFER_UDMA_2, 0x16494e31 },
- { XFER_UDMA_1, 0x164d4e31 },
- { XFER_UDMA_0, 0x16514e31 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
+static struct hpt_clock hpt37x_timings_33[] = {
+ { XFER_UDMA_6, 0x12446231 }, /* 0x12646231 ?? */
+ { XFER_UDMA_5, 0x12446231 },
+ { XFER_UDMA_4, 0x12446231 },
+ { XFER_UDMA_3, 0x126c6231 },
+ { XFER_UDMA_2, 0x12486231 },
+ { XFER_UDMA_1, 0x124c6233 },
+ { XFER_UDMA_0, 0x12506297 },
+
+ { XFER_MW_DMA_2, 0x22406c31 },
+ { XFER_MW_DMA_1, 0x22406c33 },
+ { XFER_MW_DMA_0, 0x22406c97 },
+
+ { XFER_PIO_4, 0x06414e31 },
+ { XFER_PIO_3, 0x06414e42 },
+ { XFER_PIO_2, 0x06414e53 },
+ { XFER_PIO_1, 0x06814e93 },
+ { XFER_PIO_0, 0x06814ea7 }
};
-static const struct hpt_clock hpt370_timings_66[] = {
- { XFER_UDMA_5, 0x14846231 },
- { XFER_UDMA_4, 0x14886231 },
- { XFER_UDMA_3, 0x148c6231 },
- { XFER_UDMA_2, 0x148c6231 },
- { XFER_UDMA_1, 0x14906231 },
- { XFER_UDMA_0, 0x14986231 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
+static struct hpt_clock hpt37x_timings_50[] = {
+ { XFER_UDMA_6, 0x12848242 },
+ { XFER_UDMA_5, 0x12848242 },
+ { XFER_UDMA_4, 0x12ac8242 },
+ { XFER_UDMA_3, 0x128c8242 },
+ { XFER_UDMA_2, 0x120c8242 },
+ { XFER_UDMA_1, 0x12148254 },
+ { XFER_UDMA_0, 0x121882ea },
+
+ { XFER_MW_DMA_2, 0x22808242 },
+ { XFER_MW_DMA_1, 0x22808254 },
+ { XFER_MW_DMA_0, 0x228082ea },
+
+ { XFER_PIO_4, 0x0a81f442 },
+ { XFER_PIO_3, 0x0a81f443 },
+ { XFER_PIO_2, 0x0a81f454 },
+ { XFER_PIO_1, 0x0ac1f465 },
+ { XFER_PIO_0, 0x0ac1f48a }
};
-/* these are the current (4 sep 2001) timings from highpoint */
-static const struct hpt_clock hpt370a_timings_33[] = {
- { XFER_UDMA_5, 0x12446231 },
- { XFER_UDMA_4, 0x12446231 },
- { XFER_UDMA_3, 0x126c6231 },
- { XFER_UDMA_2, 0x12486231 },
- { XFER_UDMA_1, 0x124c6233 },
- { XFER_UDMA_0, 0x12506297 },
-
- { XFER_MW_DMA_2, 0x22406c31 },
- { XFER_MW_DMA_1, 0x22406c33 },
- { XFER_MW_DMA_0, 0x22406c97 },
-
- { XFER_PIO_4, 0x06414e31 },
- { XFER_PIO_3, 0x06414e42 },
- { XFER_PIO_2, 0x06414e53 },
- { XFER_PIO_1, 0x06814e93 },
- { XFER_PIO_0, 0x06814ea7 },
- { 0, 0x06814ea7 }
+static struct hpt_clock hpt37x_timings_66[] = {
+ { XFER_UDMA_6, 0x1c869c62 },
+ { XFER_UDMA_5, 0x1cae9c62 }, /* 0x1c8a9c62 */
+ { XFER_UDMA_4, 0x1c8a9c62 },
+ { XFER_UDMA_3, 0x1c8e9c62 },
+ { XFER_UDMA_2, 0x1c929c62 },
+ { XFER_UDMA_1, 0x1c9a9c62 },
+ { XFER_UDMA_0, 0x1c829c62 },
+
+ { XFER_MW_DMA_2, 0x2c829c62 },
+ { XFER_MW_DMA_1, 0x2c829c66 },
+ { XFER_MW_DMA_0, 0x2c829d2e },
+
+ { XFER_PIO_4, 0x0c829c62 },
+ { XFER_PIO_3, 0x0c829c84 },
+ { XFER_PIO_2, 0x0c829ca6 },
+ { XFER_PIO_1, 0x0d029d26 },
+ { XFER_PIO_0, 0x0d029d5e }
};
-/* 2x 33MHz timings */
-static const struct hpt_clock hpt370a_timings_66[] = {
- { XFER_UDMA_5, 0x1488e673 },
- { XFER_UDMA_4, 0x1488e673 },
- { XFER_UDMA_3, 0x1498e673 },
- { XFER_UDMA_2, 0x1490e673 },
- { XFER_UDMA_1, 0x1498e677 },
- { XFER_UDMA_0, 0x14a0e73f },
-
- { XFER_MW_DMA_2, 0x2480fa73 },
- { XFER_MW_DMA_1, 0x2480fa77 },
- { XFER_MW_DMA_0, 0x2480fb3f },
-
- { XFER_PIO_4, 0x0c82be73 },
- { XFER_PIO_3, 0x0c82be95 },
- { XFER_PIO_2, 0x0c82beb7 },
- { XFER_PIO_1, 0x0d02bf37 },
- { XFER_PIO_0, 0x0d02bf5f },
- { 0, 0x0d02bf5f }
-};
-
-static const struct hpt_clock hpt370a_timings_50[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0ac1f48a }
-};
-
-static const struct hpt_clock hpt372_timings_33[] = {
- { XFER_UDMA_6, 0x1c81dc62 },
- { XFER_UDMA_5, 0x1c6ddc62 },
- { XFER_UDMA_4, 0x1c8ddc62 },
- { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */
- { XFER_UDMA_2, 0x1c91dc62 },
- { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */
- { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */
-
- { XFER_MW_DMA_2, 0x2c829262 },
- { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */
- { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d5e }
-};
-
-static const struct hpt_clock hpt372_timings_50[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0a81f443 }
-};
-
-static const struct hpt_clock hpt372_timings_66[] = {
- { XFER_UDMA_6, 0x1c869c62 },
- { XFER_UDMA_5, 0x1cae9c62 },
- { XFER_UDMA_4, 0x1c8a9c62 },
- { XFER_UDMA_3, 0x1c8e9c62 },
- { XFER_UDMA_2, 0x1c929c62 },
- { XFER_UDMA_1, 0x1c9a9c62 },
- { XFER_UDMA_0, 0x1c829c62 },
-
- { XFER_MW_DMA_2, 0x2c829c62 },
- { XFER_MW_DMA_1, 0x2c829c66 },
- { XFER_MW_DMA_0, 0x2c829d2e },
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d26 }
-};
-
-static const struct hpt_clock hpt374_timings_33[] = {
- { XFER_UDMA_6, 0x12808242 },
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x06814e93 }
-};
static const struct hpt_chip hpt370 = {
"HPT370",
48,
{
- hpt370_timings_33,
+ hpt37x_timings_33,
NULL,
NULL,
- hpt370_timings_66
+ NULL
}
};
"HPT370A",
48,
{
- hpt370a_timings_33,
+ hpt37x_timings_33,
NULL,
- hpt370a_timings_50,
- hpt370a_timings_66
+ hpt37x_timings_50,
+ NULL
}
};
"HPT372",
55,
{
- hpt372_timings_33,
+ hpt37x_timings_33,
NULL,
- hpt372_timings_50,
- hpt372_timings_66
+ hpt37x_timings_50,
+ hpt37x_timings_66
}
};
"HPT302",
66,
{
- hpt372_timings_33,
+ hpt37x_timings_33,
NULL,
- hpt372_timings_50,
- hpt372_timings_66
+ hpt37x_timings_50,
+ hpt37x_timings_66
}
};
"HPT371",
66,
{
- hpt372_timings_33,
+ hpt37x_timings_33,
NULL,
- hpt372_timings_50,
- hpt372_timings_66
+ hpt37x_timings_50,
+ hpt37x_timings_66
}
};
"HPT372A",
66,
{
- hpt372_timings_33,
+ hpt37x_timings_33,
NULL,
- hpt372_timings_50,
- hpt372_timings_66
+ hpt37x_timings_50,
+ hpt37x_timings_66
}
};
"HPT374",
48,
{
- hpt374_timings_33,
+ hpt37x_timings_33,
NULL,
NULL,
NULL
/**
* hpt370_filter - mode selection filter
- * @ap: ATA interface
* @adev: ATA device
*
* Block UDMA on devices that cause trouble with this controller.
*/
-static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+static unsigned long hpt370_filter(struct ata_device *adev, unsigned long mask)
{
if (adev->class == ATA_DEV_ATA) {
if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
mask &= ~ATA_MASK_UDMA;
if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
- mask &= ~(0x1F << ATA_SHIFT_UDMA);
+ mask &= ~(0xE0 << ATA_SHIFT_UDMA);
}
- return ata_pci_default_filter(ap, adev, mask);
+ return ata_bmdma_mode_filter(adev, mask);
}
/**
* hpt370a_filter - mode selection filter
- * @ap: ATA interface
* @adev: ATA device
*
* Block UDMA on devices that cause trouble with this controller.
*/
-static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+static unsigned long hpt370a_filter(struct ata_device *adev, unsigned long mask)
{
- if (adev->class != ATA_DEV_ATA) {
+ if (adev->class == ATA_DEV_ATA) {
if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
- mask &= ~ (0x1F << ATA_SHIFT_UDMA);
+ mask &= ~(0xE0 << ATA_SHIFT_UDMA);
}
- return ata_pci_default_filter(ap, adev, mask);
+ return ata_bmdma_mode_filter(adev, mask);
}
/**
- * hpt37x_pre_reset - reset the hpt37x bus
- * @ap: ATA port to reset
+ * hpt37x_cable_detect - Detect the cable type
+ * @ap: ATA port to detect on
*
- * Perform the initial reset handling for the 370/372 and 374 func 0
+ * Return the cable type attached to this port
*/
-static int hpt37x_pre_reset(struct ata_port *ap)
+static int hpt37x_cable_detect(struct ata_port *ap)
{
- u8 scr2, ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- static const struct pci_bits hpt37x_enable_bits[] = {
- { 0x50, 1, 0x04, 0x04 },
- { 0x54, 1, 0x04, 0x04 }
- };
- if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
- return -ENOENT;
+ u8 scr2, ata66;
pci_read_config_byte(pdev, 0x5B, &scr2);
pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+
+ udelay(10); /* debounce */
+
/* Cable register now active */
pci_read_config_byte(pdev, 0x5A, &ata66);
/* Restore state */
pci_write_config_byte(pdev, 0x5B, scr2);
- if (ata66 & (1 << ap->port_no))
- ap->cbl = ATA_CBL_PATA40;
+ if (ata66 & (2 >> ap->port_no))
+ return ATA_CBL_PATA40;
else
- ap->cbl = ATA_CBL_PATA80;
-
- /* Reset the state machine */
- pci_write_config_byte(pdev, 0x50, 0x37);
- pci_write_config_byte(pdev, 0x54, 0x37);
- udelay(100);
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA80;
}
/**
- * hpt37x_error_handler - reset the hpt374
- * @ap: ATA port to reset
+ * hpt374_fn1_cable_detect - Detect the cable type
+ * @ap: ATA port to detect on
*
- * Perform probe for HPT37x, except for HPT374 channel 2
+ * Return the cable type attached to this port
*/
-static void hpt37x_error_handler(struct ata_port *ap)
+static int hpt374_fn1_cable_detect(struct ata_port *ap)
{
- ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
-
-static int hpt374_pre_reset(struct ata_port *ap)
-{
- static const struct pci_bits hpt37x_enable_bits[] = {
- { 0x50, 1, 0x04, 0x04 },
- { 0x54, 1, 0x04, 0x04 }
- };
- u16 mcr3, mcr6;
- u8 ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
- if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
- return -ENOENT;
+ unsigned int mcrbase = 0x50 + 4 * ap->port_no;
+ u16 mcr3;
+ u8 ata66;
/* Do the extra channel work */
- pci_read_config_word(pdev, 0x52, &mcr3);
- pci_read_config_word(pdev, 0x56, &mcr6);
- /* Set bit 15 of 0x52 to enable TCBLID as input
- Set bit 15 of 0x56 to enable FCBLID as input
- */
- pci_write_config_word(pdev, 0x52, mcr3 | 0x8000);
- pci_write_config_word(pdev, 0x56, mcr6 | 0x8000);
+ pci_read_config_word(pdev, mcrbase + 2, &mcr3);
+ /* Set bit 15 of 0x52 to enable TCBLID as input */
+ pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000);
pci_read_config_byte(pdev, 0x5A, &ata66);
/* Reset TCBLID/FCBLID to output */
- pci_write_config_word(pdev, 0x52, mcr3);
- pci_write_config_word(pdev, 0x56, mcr6);
+ pci_write_config_word(pdev, mcrbase + 2, mcr3);
- if (ata66 & (1 << ap->port_no))
- ap->cbl = ATA_CBL_PATA40;
+ if (ata66 & (2 >> ap->port_no))
+ return ATA_CBL_PATA40;
else
- ap->cbl = ATA_CBL_PATA80;
-
- /* Reset the state machine */
- pci_write_config_byte(pdev, 0x50, 0x37);
- pci_write_config_byte(pdev, 0x54, 0x37);
- udelay(100);
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA80;
}
/**
- * hpt374_error_handler - reset the hpt374
- * @classes:
+ * hpt37x_pre_reset - reset the hpt37x bus
+ * @link: ATA link to reset
+ * @deadline: deadline jiffies for the operation
*
- * The 374 cable detect is a little different due to the extra
- * channels. The function 0 channels work like usual but function 1
- * is special
+ * Perform the initial reset handling for the HPT37x.
*/
-static void hpt374_error_handler(struct ata_port *ap)
+static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
{
+ struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ static const struct pci_bits hpt37x_enable_bits[] = {
+ { 0x50, 1, 0x04, 0x04 },
+ { 0x54, 1, 0x04, 0x04 }
+ };
+ if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
+ return -ENOENT;
- if (!(PCI_FUNC(pdev->devfn) & 1))
- hpt37x_error_handler(ap);
- else
- ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ /* Reset the state machine */
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+ udelay(100);
+
+ return ata_sff_prereset(link, deadline);
}
/**
pci_read_config_dword(pdev, addr1, ®);
mode = hpt37x_find_mode(ap, adev->pio_mode);
- mode &= ~0x8000000; /* No FIFO in PIO */
- mode &= ~0x30070000; /* Leave config bits alone */
- reg &= 0x30070000; /* Strip timing bits */
+ mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
+ reg &= ~0xCFC3FFFF; /* Strip timing bits */
pci_write_config_dword(pdev, addr1, reg | mode);
}
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, mode, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
fast |= 0x01;
pci_write_config_byte(pdev, addr2, fast);
+ mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
+
pci_read_config_dword(pdev, addr1, ®);
mode = hpt37x_find_mode(ap, adev->dma_mode);
- mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
- mode &= ~0xC0000000; /* Leave config bits alone */
- reg &= 0xC0000000; /* Strip timing bits */
+ mode &= mask;
+ reg &= ~mask;
pci_write_config_dword(pdev, addr1, reg | mode);
}
/**
- * hpt370_bmdma_start - DMA engine begin
- * @qc: ATA command
- *
- * The 370 and 370A want us to reset the DMA engine each time we
- * use it. The 372 and later are fine.
- */
-
-static void hpt370_bmdma_start(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
- udelay(10);
- ata_bmdma_start(qc);
-}
-
-/**
* hpt370_bmdma_end - DMA engine stop
* @qc: ATA command
*
mode = hpt37x_find_mode(ap, adev->pio_mode);
printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
- mode &= ~0x80000000; /* No FIFO in PIO */
- mode &= ~0x30070000; /* Leave config bits alone */
- reg &= 0x30070000; /* Strip timing bits */
+ mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
+ reg &= ~0xCFC3FFFF; /* Strip timing bits */
pci_write_config_dword(pdev, addr1, reg | mode);
}
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, mode, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
+
pci_read_config_dword(pdev, addr1, ®);
mode = hpt37x_find_mode(ap, adev->dma_mode);
printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
- mode &= ~0xC0000000; /* Leave config bits alone */
- mode |= 0x80000000; /* FIFO in MWDMA or UDMA */
- reg &= 0xC0000000; /* Strip timing bits */
+ mode &= mask;
+ reg &= ~mask;
pci_write_config_dword(pdev, addr1, reg | mode);
}
static struct scsi_host_template hpt37x_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ ATA_BMDMA_SHT(DRV_NAME),
};
/*
*/
static struct ata_port_operations hpt370_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = hpt370_set_piomode,
- .set_dmamode = hpt370_set_dmamode,
- .mode_filter = hpt370_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = hpt37x_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .inherits = &ata_bmdma_port_ops,
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = hpt370_bmdma_start,
.bmdma_stop = hpt370_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
-
- .data_xfer = ata_data_xfer,
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
+ .mode_filter = hpt370_filter,
+ .cable_detect = hpt37x_cable_detect,
+ .set_piomode = hpt370_set_piomode,
+ .set_dmamode = hpt370_set_dmamode,
+ .prereset = hpt37x_pre_reset,
};
/*
*/
static struct ata_port_operations hpt370a_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = hpt370_set_piomode,
- .set_dmamode = hpt370_set_dmamode,
+ .inherits = &hpt370_port_ops,
.mode_filter = hpt370a_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = hpt37x_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = hpt370_bmdma_start,
- .bmdma_stop = hpt370_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
-
- .data_xfer = ata_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
};
/*
*/
static struct ata_port_operations hpt372_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = hpt372_set_piomode,
- .set_dmamode = hpt372_set_dmamode,
- .mode_filter = ata_pci_default_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = hpt37x_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .inherits = &ata_bmdma_port_ops,
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
.bmdma_stop = hpt37x_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
-
- .data_xfer = ata_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
+ .cable_detect = hpt37x_cable_detect,
+ .set_piomode = hpt372_set_piomode,
+ .set_dmamode = hpt372_set_dmamode,
+ .prereset = hpt37x_pre_reset,
};
/*
* Configuration for HPT374. Mode setting works like 372 and friends
- * but we have a different cable detection procedure.
+ * but we have a different cable detection procedure for function 1.
*/
-static struct ata_port_operations hpt374_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = hpt372_set_piomode,
- .set_dmamode = hpt372_set_dmamode,
- .mode_filter = ata_pci_default_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = hpt374_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = hpt37x_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
-
- .data_xfer = ata_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
+static struct ata_port_operations hpt374_fn1_port_ops = {
+ .inherits = &hpt372_port_ops,
+ .cable_detect = hpt374_fn1_cable_detect,
+ .prereset = hpt37x_pre_reset,
};
/**
- * htp37x_clock_slot - Turn timing to PC clock entry
+ * hpt37x_clock_slot - Turn timing to PC clock entry
* @freq: Reported frequency timing
* @base: Base timing
*
/* Never went stable */
return 0;
}
+
+static u32 hpt374_read_freq(struct pci_dev *pdev)
+{
+ u32 freq;
+ unsigned long io_base = pci_resource_start(pdev, 4);
+ if (PCI_FUNC(pdev->devfn) & 1) {
+ struct pci_dev *pdev_0;
+
+ pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
+ /* Someone hot plugged the controller on us ? */
+ if (pdev_0 == NULL)
+ return 0;
+ io_base = pci_resource_start(pdev_0, 4);
+ freq = inl(io_base + 0x90);
+ pci_dev_put(pdev_0);
+ } else
+ freq = inl(io_base + 0x90);
+ return freq;
+}
+
/**
* hpt37x_init_one - Initialise an HPT37X/302
* @dev: PCI device
static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT370 - UDMA100 */
- static struct ata_port_info info_hpt370 = {
- .sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ static const struct ata_port_info info_hpt370 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt370_port_ops
};
/* HPT370A - UDMA100 */
- static struct ata_port_info info_hpt370a = {
- .sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ static const struct ata_port_info info_hpt370a = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &hpt370a_port_ops
+ };
+ /* HPT370 - UDMA100 */
+ static const struct ata_port_info info_hpt370_33 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &hpt370_port_ops
+ };
+ /* HPT370A - UDMA100 */
+ static const struct ata_port_info info_hpt370a_33 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt370a_port_ops
};
/* HPT371, 372 and friends - UDMA133 */
- static struct ata_port_info info_hpt372 = {
- .sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x7f,
+ static const struct ata_port_info info_hpt372 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
.port_ops = &hpt372_port_ops
};
- /* HPT371, 372 and friends - UDMA100 at 50MHz clock */
- static struct ata_port_info info_hpt372_50 = {
- .sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x3f,
+ /* HPT374 - UDMA100, function 1 uses different prereset method */
+ static const struct ata_port_info info_hpt374_fn0 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
.port_ops = &hpt372_port_ops
};
- /* HPT374 - UDMA133 */
- static struct ata_port_info info_hpt374 = {
- .sht = &hpt37x_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x7f,
- .port_ops = &hpt374_port_ops
+ static const struct ata_port_info info_hpt374_fn1 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &hpt374_fn1_port_ops
};
static const int MHz[4] = { 33, 40, 50, 66 };
-
- struct ata_port_info *port_info[2];
- struct ata_port_info *port;
+ void *private_data = NULL;
+ const struct ata_port_info *ppi[] = { NULL, NULL };
u8 irqmask;
u32 class_rev;
+ u8 mcr1;
u32 freq;
+ int prefer_dpll = 1;
+
+ unsigned long iobase = pci_resource_start(dev, 4);
const struct hpt_chip *chip_table;
int clock_slot;
+ int rc;
+
+ rc = pcim_enable_device(dev);
+ if (rc)
+ return rc;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
switch(class_rev) {
case 3:
- port = &info_hpt370;
+ ppi[0] = &info_hpt370;
chip_table = &hpt370;
+ prefer_dpll = 0;
break;
case 4:
- port = &info_hpt370a;
+ ppi[0] = &info_hpt370a;
chip_table = &hpt370a;
+ prefer_dpll = 0;
break;
case 5:
- port = &info_hpt372;
+ ppi[0] = &info_hpt372;
chip_table = &hpt372;
break;
default:
/* 372N if rev >= 2*/
if (class_rev >= 2)
return -ENODEV;
- port = &info_hpt372;
+ ppi[0] = &info_hpt372;
chip_table = &hpt372a;
break;
case PCI_DEVICE_ID_TTI_HPT302:
/* 302N if rev > 1 */
if (class_rev > 1)
return -ENODEV;
- port = &info_hpt372;
+ ppi[0] = &info_hpt372;
/* Check this */
chip_table = &hpt302;
break;
case PCI_DEVICE_ID_TTI_HPT371:
- port = &info_hpt372;
+ if (class_rev > 1)
+ return -ENODEV;
+ ppi[0] = &info_hpt372;
chip_table = &hpt371;
+ /* Single channel device, master is not present
+ but the BIOS (or us for non x86) must mark it
+ absent */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ mcr1 &= ~0x04;
+ pci_write_config_byte(dev, 0x50, mcr1);
break;
case PCI_DEVICE_ID_TTI_HPT374:
chip_table = &hpt374;
- port = &info_hpt374;
+ if (!(PCI_FUNC(dev->devfn) & 1))
+ *ppi = &info_hpt374_fn0;
+ else
+ *ppi = &info_hpt374_fn1;
break;
default:
printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device);
pci_write_config_byte(dev, 0x5b, 0x23);
- pci_read_config_dword(dev, 0x70, &freq);
+ /*
+ * HighPoint does this for HPT372A.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (chip_table == &hpt372a)
+ outb(0x0e, iobase + 0x9c);
+
+ /* Some devices do not let this value be accessed via PCI space
+ according to the old driver. In addition we must use the value
+ from FN 0 on the HPT374 */
+
+ if (chip_table == &hpt374) {
+ freq = hpt374_read_freq(dev);
+ if (freq == 0)
+ return -ENODEV;
+ } else
+ freq = inl(iobase + 0x90);
+
if ((freq >> 12) != 0xABCDE) {
int i;
u8 sr;
/* This is the process the HPT371 BIOS is reported to use */
for(i = 0; i < 128; i++) {
pci_read_config_byte(dev, 0x78, &sr);
- total += sr;
+ total += sr & 0x1FF;
udelay(15);
}
freq = total / 128;
*/
clock_slot = hpt37x_clock_slot(freq, chip_table->base);
- if (chip_table->clocks[clock_slot] == NULL) {
+ if (chip_table->clocks[clock_slot] == NULL || prefer_dpll) {
/*
* We need to try PLL mode instead
+ *
+ * For non UDMA133 capable devices we should
+ * use a 50MHz DPLL by choice
*/
- unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192;
- unsigned int f_high = f_low + 2;
- int adjust;
+ unsigned int f_low, f_high;
+ int dpll, adjust;
+
+ /* Compute DPLL */
+ dpll = (ppi[0]->udma_mask & 0xC0) ? 3 : 2;
+
+ f_low = (MHz[clock_slot] * 48) / MHz[dpll];
+ f_high = f_low + 2;
+ if (clock_slot > 1)
+ f_high += 2;
+
+ /* Select the DPLL clock. */
+ pci_write_config_byte(dev, 0x5b, 0x21);
+ pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
for(adjust = 0; adjust < 8; adjust++) {
if (hpt37x_calibrate_dpll(dev))
break;
/* See if it'll settle at a fractionally different clock */
- if ((adjust & 3) == 3) {
- f_low --;
- f_high ++;
- }
- pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+ if (adjust & 1)
+ f_low -= adjust >> 1;
+ else
+ f_high += adjust >> 1;
+ pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
}
if (adjust == 8) {
- printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
+ printk(KERN_ERR "pata_hpt37x: DPLL did not stabilize!\n");
return -ENODEV;
}
- /* Check if this works for all cases */
- port->private_data = (void *)hpt370_timings_66;
+ if (dpll == 3)
+ private_data = (void *)hpt37x_timings_66;
+ else
+ private_data = (void *)hpt37x_timings_50;
- printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]);
+ printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using %dMHz DPLL.\n",
+ MHz[clock_slot], MHz[dpll]);
} else {
- port->private_data = (void *)chip_table->clocks[clock_slot];
+ private_data = (void *)chip_table->clocks[clock_slot];
/*
- * Perform a final fixup. The 371 and 372 clock determines
- * if UDMA133 is available.
- */
-
- if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */
- printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n");
- if (port == &info_hpt372)
- port = &info_hpt372_50;
- else BUG();
- }
- printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
+ * Perform a final fixup. Note that we will have used the
+ * DPLL on the HPT372 which means we don't have to worry
+ * about lack of UDMA133 support on lower clocks
+ */
+
+ if (clock_slot < 2 && ppi[0] == &info_hpt370)
+ ppi[0] = &info_hpt370_33;
+ if (clock_slot < 2 && ppi[0] == &info_hpt370a)
+ ppi[0] = &info_hpt370a_33;
+ printk(KERN_INFO "pata_hpt37x: %s using %dMHz bus clock.\n",
+ chip_table->name, MHz[clock_slot]);
}
- port_info[0] = port_info[1] = port;
+
/* Now kick off ATA set up */
- return ata_pci_init_one(dev, port_info, 2);
+ return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data);
}
static const struct pci_device_id hpt37x[] = {