*
*
* TODO
- * Maybe PLL mode
- * Look into engine reset on timeout errors. Should not be
- * required.
+ * Look into engine reset on timeout errors. Should not be required.
*/
#include <linux/libata.h>
#define DRV_NAME "pata_hpt366"
-#define DRV_VERSION "0.6.2"
+#define DRV_VERSION "0.6.8"
struct hpt_clock {
- u8 xfer_speed;
+ u8 xfer_mode;
u32 timing;
};
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 16:18 udma_cycle_time. Clock cycles for UDMA xfer?
+ * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
* 31 FIFO enable.
*/
mask &= ~(0xF8 << ATA_SHIFT_UDMA);
if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
mask &= ~(0xF0 << ATA_SHIFT_UDMA);
- }
- return ata_bmdma_mode_filter(adev, mask);
-}
-
-/**
- * hpt36x_find_mode - reset the hpt36x bus
- * @ap: ATA port
- * @speed: transfer mode
- *
- * Return the 32bit register programming information for this channel
- * that matches the speed provided.
- */
-
-static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
-{
- struct hpt_clock *clocks = ap->host->private_data;
+ } else if (adev->class == ATA_DEV_ATAPI)
+ mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
- while(clocks->xfer_speed) {
- if (clocks->xfer_speed == speed)
- return clocks->timing;
- clocks++;
- }
- BUG();
- return 0xffffffffU; /* silence compiler warning */
+ return ata_bmdma_mode_filter(adev, mask);
}
static int hpt36x_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA80;
}
+static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
+{
+ struct hpt_clock *clocks = ap->host->private_data;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 addr = 0x40 + 4 * adev->devno;
+ u32 mask, reg;
+
+ /* determine timing mask and find matching clock entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xc1f8ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x303800ff;
+ else
+ mask = 0x30070000;
+
+ while (clocks->xfer_mode) {
+ if (clocks->xfer_mode == mode)
+ break;
+ clocks++;
+ }
+ if (!clocks->xfer_mode)
+ BUG();
+
+ /*
+ * Combine new mode bits with old config bits and disable
+ * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
+ * problems handling I/O errors later.
+ */
+ pci_read_config_dword(pdev, addr, ®);
+ reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
+ pci_write_config_dword(pdev, addr, reg);
+}
+
/**
* hpt366_set_piomode - PIO setup
* @ap: ATA interface
static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->pio_mode);
- mode &= ~0x8000000; /* No FIFO in PIO */
- mode &= ~0x30070000; /* Leave config bits alone */
- reg &= 0x30070000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt366_set_mode(ap, adev, adev->pio_mode);
}
/**
static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg;
- u32 mode;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- if (fast & 0x80) {
- fast &= ~0x80;
- pci_write_config_byte(pdev, addr2, fast);
- }
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt36x_find_mode(ap, adev->dma_mode);
- mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
- mode &= ~0xC0000000; /* Leave config bits alone */
- reg &= 0xC0000000; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt366_set_mode(ap, adev, adev->dma_mode);
}
static struct scsi_host_template hpt36x_sht = {
{
static const struct ata_port_info info_hpt366 = {
.flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &hpt366_port_ops
};
const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
void *hpriv = NULL;
- u32 class_rev;
u32 reg1;
int rc;
if (rc)
return rc;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xFF;
-
/* May be a later chip in disguise. Check */
/* Newer chips are not in the HPT36x driver. Ignore them */
- if (class_rev > 2)
- return -ENODEV;
+ if (dev->revision > 2)
+ return -ENODEV;
hpt36x_init_chipset(dev);
break;
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv);
+ return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
}
#ifdef CONFIG_PM
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff