/*
* pata-cs5530.c - CS5530 PATA for new ATA layer
* (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
*
* based upon cs5530.c by Mark Lord.
*
#include <linux/dmi.h>
#define DRV_NAME "pata_cs5530"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "0.7.4"
+
+static void __iomem *cs5530_port_base(struct ata_port *ap)
+{
+ unsigned long bmdma = (unsigned long)ap->ioaddr.bmdma_addr;
+
+ return (void __iomem *)((bmdma & ~0x0F) + 0x20 + 0x10 * ap->port_no);
+}
/**
* cs5530_set_piomode - PIO setup
{0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
{0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
};
- unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no;
+ void __iomem *base = cs5530_port_base(ap);
u32 tuning;
int format;
/* Find out which table to use */
- tuning = inl(base + 0x04);
+ tuning = ioread32(base + 0x04);
format = (tuning & 0x80000000UL) ? 1 : 0;
/* Now load the right timing register */
if (adev->devno)
base += 0x08;
- outl(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base);
+ iowrite32(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base);
}
/**
static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no;
+ void __iomem *base = cs5530_port_base(ap);
u32 tuning, timing = 0;
u8 reg;
/* Find out which table to use */
- tuning = inl(base + 0x04);
+ tuning = ioread32(base + 0x04);
switch(adev->dma_mode) {
case XFER_UDMA_0:
/* Merge in the PIO format bit */
timing |= (tuning & 0x80000000UL);
if (adev->devno == 0) /* Master */
- outl(timing, base + 0x04);
+ iowrite32(timing, base + 0x04);
else {
if (timing & 0x00100000)
tuning |= 0x00100000; /* UDMA for both */
else
tuning &= ~0x00100000; /* MWDMA for both */
- outl(tuning, base + 0x04);
- outl(timing, base + 0x0C);
+ iowrite32(tuning, base + 0x04);
+ iowrite32(timing, base + 0x0C);
}
/* Set the DMA capable bit in the BMDMA area */
- reg = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ reg = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
reg |= (1 << (5 + adev->devno));
- outb(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ iowrite8(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
/* Remember the last DMA setup we did */
}
/**
- * cs5530_qc_issue_prot - command issue
+ * cs5530_qc_issue - command issue
* @qc: command pending
*
* Called when the libata layer is about to issue a command. We wrap
* this interface so that we can load the correct ATA timings if
- * neccessary. Specifically we have a problem that there is only
+ * necessary. Specifically we have a problem that there is only
* one MWDMA/UDMA bit.
*/
-static unsigned int cs5530_qc_issue_prot(struct ata_queued_cmd *qc)
+static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *adev = qc->dev;
struct ata_device *prev = ap->private_data;
/* See if the DMA settings could be wrong */
- if (adev->dma_mode != 0 && adev != prev && prev != NULL) {
+ if (ata_dma_enabled(adev) && adev != prev && prev != NULL) {
/* Maybe, but do the channels match MWDMA/UDMA ? */
- if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) ||
- (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0))
+ if ((ata_using_udma(adev) && !ata_using_udma(prev)) ||
+ (ata_using_udma(prev) && !ata_using_udma(adev)))
/* Switch the mode bits */
cs5530_set_dmamode(ap, adev);
}
- return ata_qc_issue_prot(qc);
-}
-
-static int cs5530_pre_reset(struct ata_port *ap)
-{
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
-}
-
-static void cs5530_error_handler(struct ata_port *ap)
-{
- return ata_bmdma_drive_eh(ap, cs5530_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ return ata_sff_qc_issue(qc);
}
-
static struct scsi_host_template cs5530_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ ATA_BMDMA_SHT(DRV_NAME),
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
};
static struct ata_port_operations cs5530_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = cs5530_set_piomode,
- .set_dmamode = cs5530_set_dmamode,
- .mode_filter = ata_pci_default_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = cs5530_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = cs5530_qc_issue_prot,
-
- .data_xfer = ata_pio_data_xfer,
+ .inherits = &ata_bmdma_port_ops,
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
+ .qc_prep = ata_sff_dumb_qc_prep,
+ .qc_issue = cs5530_qc_issue,
- .port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
+ .cable_detect = ata_cable_40wire,
+ .set_piomode = cs5530_set_piomode,
+ .set_dmamode = cs5530_set_dmamode,
};
-static struct dmi_system_id palmax_dmi_table[] = {
+static const struct dmi_system_id palmax_dmi_table[] = {
{
.ident = "Palmax PD1100",
.matches = {
return 0;
}
+
/**
- * cs5530_init_one - Initialise a CS5530
- * @dev: PCI device
- * @id: Entry in match table
+ * cs5530_init_chip - Chipset init
*
- * Install a driver for the newly found CS5530 companion chip. Most of
- * this is just housekeeping. We have to set the chip up correctly and
- * turn off various bits of emulation magic.
+ * Perform the chip initialisation work that is shared between both
+ * setup and resume paths
*/
-static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+static int cs5530_init_chip(void)
{
- int compiler_warning_pointless_fix;
- struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
- static struct ata_port_info info = {
- .sht = &cs5530_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x07,
- .udma_mask = 0x07,
- .port_ops = &cs5530_port_ops
- };
- /* The docking connector doesn't do UDMA, and it seems not MWDMA */
- static struct ata_port_info info_palmax_secondary = {
- .sht = &cs5530_sht,
- .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .port_ops = &cs5530_port_ops
- };
- static struct ata_port_info *port_info[2] = { &info, &info };
+ struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL;
- dev = NULL;
while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
switch (dev->device) {
case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
}
pci_set_master(cs5530_0);
- compiler_warning_pointless_fix = pci_set_mwi(cs5530_0);
+ pci_try_set_mwi(cs5530_0);
/*
* Set PCI CacheLineSize to 16-bytes:
pci_dev_put(master_0);
pci_dev_put(cs5530_0);
-
- if (cs5530_is_palmax())
- port_info[1] = &info_palmax_secondary;
-
- /* Now kick off ATA set up */
- return ata_pci_init_one(dev, port_info, 2);
-
+ return 0;
fail_put:
if (master_0)
pci_dev_put(master_0);
return -ENODEV;
}
+/**
+ * cs5530_init_one - Initialise a CS5530
+ * @dev: PCI device
+ * @id: Entry in match table
+ *
+ * Install a driver for the newly found CS5530 companion chip. Most of
+ * this is just housekeeping. We have to set the chip up correctly and
+ * turn off various bits of emulation magic.
+ */
+
+static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ static const struct ata_port_info info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
+ .port_ops = &cs5530_port_ops
+ };
+ /* The docking connector doesn't do UDMA, and it seems not MWDMA */
+ static const struct ata_port_info info_palmax_secondary = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .port_ops = &cs5530_port_ops
+ };
+ const struct ata_port_info *ppi[] = { &info, NULL };
+ int rc;
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* Chip initialisation */
+ if (cs5530_init_chip())
+ return -ENODEV;
+
+ if (cs5530_is_palmax())
+ ppi[1] = &info_palmax_secondary;
+
+ /* Now kick off ATA set up */
+ return ata_pci_sff_init_one(pdev, ppi, &cs5530_sht, NULL);
+}
+
+#ifdef CONFIG_PM
+static int cs5530_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ /* If we fail on resume we are doomed */
+ if (cs5530_init_chip())
+ return -EIO;
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif /* CONFIG_PM */
+
static const struct pci_device_id cs5530[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
.name = DRV_NAME,
.id_table = cs5530,
.probe = cs5530_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = cs5530_reinit_one,
+#endif
};
static int __init cs5530_init(void)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff