#include <linux/libata.h>
#define DRV_NAME "pata_cs5520"
-#define DRV_VERSION "0.6.4"
+#define DRV_VERSION "0.6.6"
struct pio_clocks
{
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static struct ata_port_operations cs5520_port_ops = {
- .port_disable = ata_port_disable,
.set_piomode = cs5520_set_piomode,
.set_dmamode = cs5520_set_dmamode,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
- .qc_prep = ata_qc_prep,
+ .qc_prep = ata_dumb_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
- .irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .irq_ack = ata_irq_ack,
- .port_start = ata_port_start,
+ .port_start = ata_sff_port_start,
};
-static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
+ static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
+ static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
+ struct ata_port_info pi = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f,
+ .port_ops = &cs5520_port_ops,
+ };
+ const struct ata_port_info *ppi[2];
u8 pcicfg;
void __iomem *iomap[5];
- static struct ata_probe_ent probe[2];
- int ports = 0;
+ struct ata_host *host;
+ struct ata_ioports *ioaddr;
+ int i, rc;
/* IDE port enable bits */
- pci_read_config_byte(dev, 0x60, &pcicfg);
+ pci_read_config_byte(pdev, 0x60, &pcicfg);
/* Check if the ATA ports are enabled */
if ((pcicfg & 3) == 0)
return -ENODEV;
+ ppi[0] = ppi[1] = &ata_dummy_port_info;
+ if (pcicfg & 1)
+ ppi[0] = π
+ if (pcicfg & 2)
+ ppi[1] = π
+
if ((pcicfg & 0x40) == 0) {
- printk(KERN_WARNING DRV_NAME ": DMA mode disabled. Enabling.\n");
- pci_write_config_byte(dev, 0x60, pcicfg | 0x40);
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "DMA mode disabled. Enabling.\n");
+ pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
}
+ pi.mwdma_mask = id->driver_data;
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+
/* Perform set up for DMA */
- if (pci_enable_device_bars(dev, 1<<2)) {
+ if (pci_enable_device_io(pdev)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
- pci_set_master(dev);
- if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
+
+ if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
return -ENODEV;
}
- if (pci_set_consistent_dma_mask(dev, DMA_32BIT_MASK)) {
+ if (pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK)) {
printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
return -ENODEV;
}
- /* Map IO ports */
- iomap[0] = devm_ioport_map(&dev->dev, 0x1F0, 8);
- iomap[1] = devm_ioport_map(&dev->dev, 0x3F6, 1);
- iomap[2] = devm_ioport_map(&dev->dev, 0x170, 8);
- iomap[3] = devm_ioport_map(&dev->dev, 0x376, 1);
- iomap[4] = pcim_iomap(dev, 2, 0);
+ /* Map IO ports and initialize host accordingly */
+ iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
+ iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
+ iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
+ iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
+ iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
return -ENOMEM;
- /* We have to do our own plumbing as the PCI setup for this
- chipset is non-standard so we can't punt to the libata code */
-
- INIT_LIST_HEAD(&probe[0].node);
- probe[0].dev = pci_dev_to_dev(dev);
- probe[0].port_ops = &cs5520_port_ops;
- probe[0].sht = &cs5520_sht;
- probe[0].pio_mask = 0x1F;
- probe[0].mwdma_mask = id->driver_data;
- probe[0].irq = 14;
- probe[0].irq_flags = 0;
- probe[0].port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
- probe[0].n_ports = 1;
- probe[0].port[0].cmd_addr = iomap[0];
- probe[0].port[0].ctl_addr = iomap[1];
- probe[0].port[0].altstatus_addr = iomap[1];
- probe[0].port[0].bmdma_addr = iomap[4];
-
- /* The secondary lurks at different addresses but is otherwise
- the same beastie */
-
- probe[1] = probe[0];
- INIT_LIST_HEAD(&probe[1].node);
- probe[1].irq = 15;
- probe[1].port[0].cmd_addr = iomap[2];
- probe[1].port[0].ctl_addr = iomap[3];
- probe[1].port[0].altstatus_addr = iomap[3];
- probe[1].port[0].bmdma_addr = iomap[4] + 8;
-
- /* Let libata fill in the port details */
- ata_std_ports(&probe[0].port[0]);
- ata_std_ports(&probe[1].port[0]);
-
- /* Now add the ports that are active */
- if (pcicfg & 1)
- ports += ata_device_add(&probe[0]);
- if (pcicfg & 2)
- ports += ata_device_add(&probe[1]);
- if (ports)
- return 0;
- return -ENODEV;
-}
+ ioaddr = &host->ports[0]->ioaddr;
+ ioaddr->cmd_addr = iomap[0];
+ ioaddr->ctl_addr = iomap[1];
+ ioaddr->altstatus_addr = iomap[1];
+ ioaddr->bmdma_addr = iomap[4];
+ ata_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[0],
+ "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
+ ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
+
+ ioaddr = &host->ports[1]->ioaddr;
+ ioaddr->cmd_addr = iomap[2];
+ ioaddr->ctl_addr = iomap[3];
+ ioaddr->altstatus_addr = iomap[3];
+ ioaddr->bmdma_addr = iomap[4] + 8;
+ ata_std_ports(ioaddr);
+
+ ata_port_desc(host->ports[1],
+ "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
+ ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
+
+ /* activate the host */
+ pci_set_master(pdev);
+ rc = ata_host_start(host);
+ if (rc)
+ return rc;
-/**
- * cs5520_remove_one - device unload
- * @pdev: PCI device being removed
- *
- * Handle an unplug/unload event for a PCI device. Unload the
- * PCI driver but do not use the default handler as we manage
- * resources ourself and *MUST NOT* disable the device as it has
- * other functions.
- */
+ for (i = 0; i < 2; i++) {
+ static const int irq[] = { 14, 15 };
+ struct ata_port *ap = host->ports[i];
-static void __devexit cs5520_remove_one(struct pci_dev *pdev)
-{
- struct device *dev = pci_dev_to_dev(pdev);
- struct ata_host *host = dev_get_drvdata(dev);
+ if (ata_port_is_dummy(ap))
+ continue;
+
+ rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
+ ata_interrupt, 0, DRV_NAME, host);
+ if (rc)
+ return rc;
+
+ ata_port_desc(ap, "irq %d", irq[i]);
+ }
- ata_host_detach(host);
+ return ata_host_register(host, &cs5520_sht);
}
#ifdef CONFIG_PM
.name = DRV_NAME,
.id_table = pata_cs5520,
.probe = cs5520_init_one,
- .remove = cs5520_remove_one,
+ .remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = cs5520_pci_device_suspend,
.resume = cs5520_reinit_one,