* Documentation
* Publically available from Intel web site. Errata documentation
* is also publically available. As an aide to anyone hacking on this
- * driver the list of errata that are relevant is below.going back to
+ * driver the list of errata that are relevant is below, going back to
* PIIX4. Older device documentation is now a bit tricky to find.
*
* The chipsets all follow very much the same design. The orginal Triton
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
+#include <linux/dmi.h>
#define DRV_NAME "ata_piix"
-#define DRV_VERSION "2.00ac7"
+#define DRV_VERSION "2.12"
enum {
PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
ICH5_PCS = 0x92, /* port control and status */
PIIX_SCC = 0x0A, /* sub-class code register */
- PIIX_FLAG_IGNORE_PCS = (1 << 25), /* ignore PCS present bits */
PIIX_FLAG_SCR = (1 << 26), /* SCR available */
PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
+ PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS,
+ PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
+
/* combined mode. if set, PATA is channel 0.
* if clear, PATA is channel 1.
*/
PIIX_80C_SEC = (1 << 7) | (1 << 6),
/* controller IDs */
- piix_pata_33 = 0, /* PIIX3 or 4 at 33Mhz */
+ piix_pata_33 = 0, /* PIIX4 at 33Mhz */
ich_pata_33 = 1, /* ICH up to UDMA 33 only */
ich_pata_66 = 2, /* ICH up to 66 Mhz */
ich_pata_100 = 3, /* ICH up to UDMA 100 */
ich_pata_133 = 4, /* ICH up to UDMA 133 */
ich5_sata = 5,
- esb_sata = 6,
- ich6_sata = 7,
- ich6_sata_ahci = 8,
- ich6m_sata_ahci = 9,
- ich8_sata_ahci = 10,
+ ich6_sata = 6,
+ ich6_sata_ahci = 7,
+ ich6m_sata_ahci = 8,
+ ich8_sata_ahci = 9,
+ piix_pata_mwdma = 10, /* PIIX3 MWDMA only */
+ tolapai_sata_ahci = 11,
/* constants for mapping table */
P0 = 0, /* port 0 */
RV = -3, /* reserved */
PIIX_AHCI_DEVICE = 6,
+
+ /* host->flags bits */
+ PIIX_HOST_BROKEN_SUSPEND = (1 << 24),
};
struct piix_map_db {
const u32 mask;
const u16 port_enable;
- const int present_shift;
const int map[][4];
};
struct piix_host_priv {
const int *map;
- const struct piix_map_db *map_db;
};
static int piix_init_one (struct pci_dev *pdev,
const struct pci_device_id *ent);
-static void piix_host_stop(struct ata_host *host);
static void piix_pata_error_handler(struct ata_port *ap);
-static void ich_pata_error_handler(struct ata_port *ap);
-static void piix_sata_error_handler(struct ata_port *ap);
static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev);
+static int ich_pata_cable_detect(struct ata_port *ap);
+#ifdef CONFIG_PM
+static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
+static int piix_pci_device_resume(struct pci_dev *pdev);
+#endif
static unsigned int in_module_init = 1;
static const struct pci_device_id piix_pci_tbl[] = {
-#ifdef ATA_ENABLE_PATA
+ /* Intel PIIX3 for the 430HX etc */
+ { 0x8086, 0x7010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_mwdma },
/* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
/* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
{ 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
- { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
- { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
/* Intel PIIX4 */
{ 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
/* Intel PIIX4 */
/* ICH7/7-R (i945, i975) UDMA 100*/
{ 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 },
{ 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
-#endif
+ /* ICH8 Mobile PATA Controller */
+ { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
/* NOTE: The following PCI ids must be kept in sync with the
* list in drivers/pci/quirks.c.
/* 82801EB (ICH5) */
{ 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
/* 6300ESB (ICH5 variant with broken PCS present bits) */
- { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
/* 6300ESB pretending RAID */
- { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata },
+ { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
/* 82801FB/FW (ICH6/ICH6W) */
{ 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
/* 82801FR/FRW (ICH6R/ICH6RW) */
{ 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
/* 2801GBM/GHM (ICH7M, identical to ICH6M) */
{ 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
- /* Enterprise Southbridge 2 (where's the datasheet?) */
+ /* Enterprise Southbridge 2 (631xESB/632xESB) */
{ 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
- /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+ /* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* SATA Controller 2 IDE (ICH8, ditto) */
+ /* SATA Controller 2 IDE (ICH8) */
{ 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
- /* Mobile SATA Controller IDE (ICH8M, ditto) */
+ /* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9) */
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (ICH9M) */
+ { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* SATA Controller IDE (Tolapai) */
+ { 0x8086, 0x5028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, tolapai_sata_ahci },
{ } /* terminate list */
};
.id_table = piix_pci_tbl,
.probe = piix_init_one,
.remove = ata_pci_remove_one,
- .suspend = ata_pci_device_suspend,
- .resume = ata_pci_device_resume,
+#ifdef CONFIG_PM
+ .suspend = piix_pci_device_suspend,
+ .resume = piix_pci_device_resume,
+#endif
};
static struct scsi_host_template piix_sht = {
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations piix_pata_ops = {
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = piix_pata_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = piix_host_stop,
};
static const struct ata_port_operations ich_pata_ops = {
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = ich_pata_error_handler,
+ .error_handler = piix_pata_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ich_pata_cable_detect,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop,
};
static const struct ata_port_operations piix_sata_ops = {
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = piix_sata_error_handler,
+ .error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = piix_host_stop,
};
static const struct piix_map_db ich5_map_db = {
.mask = 0x7,
.port_enable = 0x3,
- .present_shift = 4,
.map = {
/* PM PS SM SS MAP */
{ P0, NA, P1, NA }, /* 000b */
static const struct piix_map_db ich6_map_db = {
.mask = 0x3,
.port_enable = 0xf,
- .present_shift = 4,
.map = {
/* PM PS SM SS MAP */
{ P0, P2, P1, P3 }, /* 00b */
static const struct piix_map_db ich6m_map_db = {
.mask = 0x3,
.port_enable = 0x5,
- .present_shift = 4,
/* Map 01b isn't specified in the doc but some notebooks use
* it anyway. MAP 01b have been spotted on both ICH6M and
*/
.map = {
/* PM PS SM SS MAP */
- { P0, P2, RV, RV }, /* 00b */
+ { P0, P2, NA, NA }, /* 00b */
{ IDE, IDE, P1, P3 }, /* 01b */
{ P0, P2, IDE, IDE }, /* 10b */
{ RV, RV, RV, RV },
static const struct piix_map_db ich8_map_db = {
.mask = 0x3,
.port_enable = 0x3,
- .present_shift = 8,
.map = {
/* PM PS SM SS MAP */
{ P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
{ RV, RV, RV, RV },
- { IDE, IDE, NA, NA }, /* 10b (IDE mode) */
+ { P0, P2, IDE, IDE }, /* 10b (IDE mode) */
{ RV, RV, RV, RV },
},
};
+static const struct piix_map_db tolapai_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x3,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, P1, NA }, /* 00b */
+ { RV, RV, RV, RV }, /* 01b */
+ { RV, RV, RV, RV }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
static const struct piix_map_db *piix_map_db_table[] = {
[ich5_sata] = &ich5_map_db,
- [esb_sata] = &ich5_map_db,
[ich6_sata] = &ich6_map_db,
[ich6_sata_ahci] = &ich6_map_db,
[ich6m_sata_ahci] = &ich6m_map_db,
[ich8_sata_ahci] = &ich8_map_db,
+ [tolapai_sata_ahci] = &tolapai_map_db,
};
static struct ata_port_info piix_port_info[] = {
- /* piix_pata_33: 0: PIIX3 or 4 at 33MHz */
+ /* piix_pata_33: 0: PIIX4 at 33MHz */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
.udma_mask = ATA_UDMA_MASK_40C,
/* ich_pata_33: 1 ICH0 - ICH at 33Mhz*/
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
+ .flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio 0-4 */
.mwdma_mask = 0x06, /* Check: maybe 0x07 */
.udma_mask = ATA_UDMA2, /* UDMA33 */
/* ich_pata_66: 2 ICH controllers up to 66MHz */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS,
+ .flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio 0-4 */
.mwdma_mask = 0x06, /* MWDMA0 is broken on chip */
.udma_mask = ATA_UDMA4,
/* ich_pata_100: 3 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+ .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 */
.udma_mask = ATA_UDMA5, /* udma0-5 */
/* ich_pata_133: 4 ICH with full UDMA6 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
+ .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
.pio_mask = 0x1f, /* pio 0-4 */
.mwdma_mask = 0x06, /* Check: maybe 0x07 */
.udma_mask = ATA_UDMA6, /* UDMA133 */
/* ich5_sata: 5 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR |
- PIIX_FLAG_IGNORE_PCS,
+ .flags = PIIX_SATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
- /* i6300esb_sata: 6 */
+ /* ich6_sata: 6 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA |
- PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
- /* ich6_sata: 7 */
+ /* ich6_sata_ahci: 7 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA |
- PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
- /* ich6_sata_ahci: 8 */
+ /* ich6m_sata_ahci: 8 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA |
- PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
- /* ich6m_sata_ahci: 9 */
+ /* ich8_sata_ahci: 9 */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA |
- PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
- /* ich8_sata_ahci: 10 */
+ /* piix_pata_mwdma: 10: PIIX3 MWDMA only */
{
.sht = &piix_sht,
- .flags = ATA_FLAG_SATA |
- PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR |
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .port_ops = &piix_pata_ops,
+ },
+
+ /* tolapai_sata_ahci: 11: */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
+ .udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
-
};
static struct pci_bits piix_enable_bits[] = {
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
MODULE_VERSION(DRV_VERSION);
-static int force_pcs = 0;
-module_param(force_pcs, int, 0444);
-MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around "
- "device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)");
-
struct ich_laptop {
u16 device;
u16 subvendor;
static const struct ich_laptop ich_laptop[] = {
/* devid, subvendor, subdev */
{ 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
+ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */
/* end marker */
{ 0, }
};
/**
- * piix_pata_cbl_detect - Probe host controller cable detect info
+ * ich_pata_cable_detect - Probe host controller cable detect info
* @ap: Port for which cable detect info is desired
*
* Read 80c cable indicator from ATA PCI device's PCI config
* None (inherited from caller).
*/
-static void ich_pata_cbl_detect(struct ata_port *ap)
+static int ich_pata_cable_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
const struct ich_laptop *lap = &ich_laptop[0];
u8 tmp, mask;
- /* no 80c support in host controller? */
- if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
- goto cbl40;
-
/* Check for specials - Acer Aspire 5602WLMi */
while (lap->device) {
if (lap->device == pdev->device &&
lap->subvendor == pdev->subsystem_vendor &&
lap->subdevice == pdev->subsystem_device) {
- ap->cbl = ATA_CBL_PATA40_SHORT;
- return;
+ return ATA_CBL_PATA40_SHORT;
}
lap++;
}
mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
if ((tmp & mask) == 0)
- goto cbl40;
-
- ap->cbl = ATA_CBL_PATA80;
- return;
-
-cbl40:
- ap->cbl = ATA_CBL_PATA40;
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
/**
* piix_pata_prereset - prereset for PATA host controller
* @ap: Target port
- *
+ * @deadline: deadline jiffies for the operation
*
* LOCKING:
* None (inherited from caller).
*/
-static int piix_pata_prereset(struct ata_port *ap)
+static int piix_pata_prereset(struct ata_port *ap, unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
return -ENOENT;
-
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
static void piix_pata_error_handler(struct ata_port *ap)
ata_std_postreset);
}
-
-/**
- * ich_pata_prereset - prereset for PATA host controller
- * @ap: Target port
- *
- *
- * LOCKING:
- * None (inherited from caller).
- */
-static int ich_pata_prereset(struct ata_port *ap)
-{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
- if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) {
- ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
- ap->eh_context.i.action &= ~ATA_EH_RESET_MASK;
- return 0;
- }
-
- ich_pata_cbl_detect(ap);
-
- return ata_std_prereset(ap);
-}
-
-static void ich_pata_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, ich_pata_prereset, ata_std_softreset, NULL,
- ata_std_postreset);
-}
-
-/**
- * piix_sata_present_mask - determine present mask for SATA host controller
- * @ap: Target port
- *
- * Reads SATA PCI device's PCI config register Port Configuration
- * and Status (PCS) to determine port and device availability.
- *
- * LOCKING:
- * None (inherited from caller).
- *
- * RETURNS:
- * determined present_mask
- */
-static unsigned int piix_sata_present_mask(struct ata_port *ap)
-{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- struct piix_host_priv *hpriv = ap->host->private_data;
- const unsigned int *map = hpriv->map;
- int base = 2 * ap->port_no;
- unsigned int present_mask = 0;
- int port, i;
- u16 pcs;
-
- pci_read_config_word(pdev, ICH5_PCS, &pcs);
- DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
-
- for (i = 0; i < 2; i++) {
- port = map[base + i];
- if (port < 0)
- continue;
- if ((ap->flags & PIIX_FLAG_IGNORE_PCS) ||
- (pcs & 1 << (hpriv->map_db->present_shift + port)))
- present_mask |= 1 << i;
- }
-
- DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
- ap->id, pcs, present_mask);
-
- return present_mask;
-}
-
-/**
- * piix_sata_softreset - reset SATA host port via ATA SRST
- * @ap: port to reset
- * @classes: resulting classes of attached devices
- *
- * Reset SATA host port via ATA SRST. On controllers with
- * reliable PCS present bits, the bits are used to determine
- * device presence.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-static int piix_sata_softreset(struct ata_port *ap, unsigned int *classes)
-{
- unsigned int present_mask;
- int i, rc;
-
- present_mask = piix_sata_present_mask(ap);
-
- rc = ata_std_softreset(ap, classes);
- if (rc)
- return rc;
-
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
- if (!(present_mask & (1 << i)))
- classes[i] = ATA_DEV_NONE;
- }
-
- return 0;
-}
-
-static void piix_sata_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, ata_std_prereset, piix_sata_softreset, NULL,
- ata_std_postreset);
-}
-
/**
* piix_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE enable */
+ /* PIO configuration clears DTE unconditionally. It will be
+ * programmed in set_dmamode which is guaranteed to be called
+ * after set_piomode if any DMA mode is available.
+ */
pci_read_config_word(dev, master_port, &master_data);
if (is_slave) {
+ /* clear TIME1|IE1|PPE1|DTE1 */
+ master_data &= 0xff0f;
/* Enable SITRE (seperate slave timing register) */
master_data |= 0x4000;
/* enable PPE1, IE1 and TIME1 as needed */
pci_read_config_byte(dev, slave_port, &slave_data);
slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the timing nibble for this slave */
- slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1])
+ << (ap->port_no ? 4 : 0);
} else {
- /* Master keeps the bits in a different format */
- master_data &= 0xccf8;
+ /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */
+ master_data &= 0xccf0;
/* Enable PPE, IE and TIME as appropriate */
master_data |= control;
+ /* load ISP and RCT */
master_data |=
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
u16 master_data;
u8 speed = adev->dma_mode;
int devid = adev->devno + 2 * ap->port_no;
- u8 udma_enable;
+ u8 udma_enable = 0;
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 2, 3 }, };
pci_read_config_word(dev, master_port, &master_data);
- pci_read_config_byte(dev, 0x48, &udma_enable);
+ if (ap->udma_mask)
+ pci_read_config_byte(dev, 0x48, &udma_enable);
if (speed >= XFER_UDMA_0) {
unsigned int udma = adev->dma_mode - XFER_UDMA_0;
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= (0x0F + 0xE1 * ap->port_no);
+ slave_data &= (ap->port_no ? 0x0f : 0xf0);
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
}
- udma_enable &= ~(1 << devid);
- pci_write_config_word(dev, master_port, master_data);
+
+ if (ap->udma_mask) {
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, master_port, master_data);
+ }
}
/* Don't scribble on 0x48 if the controller does not support UDMA */
if (ap->udma_mask)
do_pata_set_dmamode(ap, adev, 1);
}
+#ifdef CONFIG_PM
+static int piix_broken_suspend(void)
+{
+ static const struct dmi_system_id sysids[] = {
+ {
+ .ident = "TECRA M3",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M3"),
+ },
+ },
+ {
+ .ident = "TECRA M5",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
+ },
+ },
+ {
+ .ident = "TECRA M7",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M7"),
+ },
+ },
+ {
+ .ident = "Satellite U200",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
+ },
+ },
+ {
+ .ident = "Satellite U205",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+ },
+ },
+ {
+ .ident = "Portege M500",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
+ },
+ },
+
+ { } /* terminate list */
+ };
+ static const char *oemstrs[] = {
+ "Tecra M3,",
+ };
+ int i;
+
+ if (dmi_check_system(sysids))
+ return 1;
+
+ for (i = 0; i < ARRAY_SIZE(oemstrs); i++)
+ if (dmi_find_device(DMI_DEV_TYPE_OEM_STRING, oemstrs[i], NULL))
+ return 1;
+
+ return 0;
+}
+
+static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ unsigned long flags;
+ int rc = 0;
+
+ rc = ata_host_suspend(host, mesg);
+ if (rc)
+ return rc;
+
+ /* Some braindamaged ACPI suspend implementations expect the
+ * controller to be awake on entry; otherwise, it burns cpu
+ * cycles and power trying to do something to the sleeping
+ * beauty.
+ */
+ if (piix_broken_suspend() && mesg.event == PM_EVENT_SUSPEND) {
+ pci_save_state(pdev);
+
+ /* mark its power state as "unknown", since we don't
+ * know if e.g. the BIOS will change its device state
+ * when we suspend.
+ */
+ if (pdev->current_state == PCI_D0)
+ pdev->current_state = PCI_UNKNOWN;
+
+ /* tell resume that it's waking up from broken suspend */
+ spin_lock_irqsave(&host->lock, flags);
+ host->flags |= PIIX_HOST_BROKEN_SUSPEND;
+ spin_unlock_irqrestore(&host->lock, flags);
+ } else
+ ata_pci_device_do_suspend(pdev, mesg);
+
+ return 0;
+}
+
+static int piix_pci_device_resume(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ unsigned long flags;
+ int rc;
+
+ if (host->flags & PIIX_HOST_BROKEN_SUSPEND) {
+ spin_lock_irqsave(&host->lock, flags);
+ host->flags &= ~PIIX_HOST_BROKEN_SUSPEND;
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+
+ /* PCI device wasn't disabled during suspend. Use
+ * pci_reenable_device() to avoid affecting the enable
+ * count.
+ */
+ rc = pci_reenable_device(pdev);
+ if (rc)
+ dev_printk(KERN_ERR, &pdev->dev, "failed to enable "
+ "device after resume (%d)\n", rc);
+ } else
+ rc = ata_pci_device_do_resume(pdev);
+
+ if (rc == 0)
+ ata_host_resume(host);
+
+ return rc;
+}
+#endif
+
#define AHCI_PCI_BAR 5
#define AHCI_GLOBAL_CTL 0x04
#define AHCI_ENABLE (1 << 31)
{
struct pci_dev *pdev = NULL;
u16 cfg;
- u8 rev;
int no_piix_dma = 0;
while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
{
/* Look for 450NX PXB. Check for problem configurations
A PCI quirk checks bit 6 already */
- pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
pci_read_config_word(pdev, 0x41, &cfg);
/* Only on the original revision: IDE DMA can hang */
- if (rev == 0x00)
+ if (pdev->revision == 0x00)
no_piix_dma = 1;
/* On all revisions below 5 PXB bus lock must be disabled for IDE */
- else if (cfg & (1<<14) && rev < 5)
+ else if (cfg & (1<<14) && pdev->revision < 5)
no_piix_dma = 2;
}
if (no_piix_dma)
pci_write_config_word(pdev, ICH5_PCS, new_pcs);
msleep(150);
}
-
- if (force_pcs == 1) {
- dev_printk(KERN_INFO, &pdev->dev,
- "force ignoring PCS (0x%x)\n", new_pcs);
- pinfo[0].flags |= PIIX_FLAG_IGNORE_PCS;
- pinfo[1].flags |= PIIX_FLAG_IGNORE_PCS;
- } else if (force_pcs == 2) {
- dev_printk(KERN_INFO, &pdev->dev,
- "force honoring PCS (0x%x)\n", new_pcs);
- pinfo[0].flags &= ~PIIX_FLAG_IGNORE_PCS;
- pinfo[1].flags &= ~PIIX_FLAG_IGNORE_PCS;
- }
}
static void __devinit piix_init_sata_map(struct pci_dev *pdev,
"invalid MAP value %u\n", map_value);
hpriv->map = map;
- hpriv->map_db = map_db;
+}
+
+static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
+{
+ static const struct dmi_system_id sysids[] = {
+ {
+ /* Clevo M570U sets IOCFG bit 18 if the cdrom
+ * isn't used to boot the system which
+ * disables the channel.
+ */
+ .ident = "M570U",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Clevo Co."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "M570U"),
+ },
+ },
+
+ { } /* terminate list */
+ };
+ u32 iocfg;
+
+ if (!dmi_check_system(sysids))
+ return;
+
+ /* The datasheet says that bit 18 is NOOP but certain systems
+ * seem to use it to disable a channel. Clear the bit on the
+ * affected systems.
+ */
+ pci_read_config_dword(pdev, PIIX_IOCFG, &iocfg);
+ if (iocfg & (1 << 18)) {
+ dev_printk(KERN_INFO, &pdev->dev,
+ "applying IOCFG bit18 quirk\n");
+ iocfg &= ~(1 << 18);
+ pci_write_config_dword(pdev, PIIX_IOCFG, iocfg);
+ }
}
/**
static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
+ struct device *dev = &pdev->dev;
struct ata_port_info port_info[2];
- struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] };
+ const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] };
struct piix_host_priv *hpriv;
unsigned long port_flags;
if (!in_module_init)
return -ENODEV;
- hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+ hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
piix_map_db_table[ent->driver_data]);
}
+ /* apply IOCFG bit18 quirk */
+ piix_iocfg_bit18_quirk(pdev);
+
/* On ICH5, some BIOSen disable the interrupt using the
* PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
* On ICH6, this bit has the same effect, but only when
port_info[1].mwdma_mask = 0;
port_info[1].udma_mask = 0;
}
- return ata_pci_init_one(pdev, ppinfo, 2);
-}
-
-static void piix_host_stop(struct ata_host *host)
-{
- struct piix_host_priv *hpriv = host->private_data;
-
- ata_host_stop(host);
-
- kfree(hpriv);
+ return ata_pci_init_one(pdev, ppi);
}
static int __init piix_init(void)