#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
+#include <linux/dmi.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
#define DRV_NAME "ahci"
#define DRV_VERSION "3.0"
+static int ahci_skip_host_reset;
+module_param_named(skip_host_reset, ahci_skip_host_reset, int, 0444);
+MODULE_PARM_DESC(skip_host_reset, "skip global host reset (0=don't skip, 1=skip)");
+
+static int ahci_enable_alpm(struct ata_port *ap,
+ enum link_pm policy);
+static void ahci_disable_alpm(struct ata_port *ap);
enum {
AHCI_PCI_BAR = 5,
AHCI_MAX_PORTS = 32,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
- AHCI_USE_CLUSTERING = 1,
AHCI_MAX_CMDS = 32,
AHCI_CMD_SZ = 32,
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
board_ahci_ign_iferr = 2,
board_ahci_sb600 = 3,
board_ahci_mv = 4,
+ board_ahci_sb700 = 5,
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
+ HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_SNTF = (1 << 29), /* SNotification register */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
+ PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
+ PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
PORT_CMD_PMP = (1 << 17), /* PMP attached */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
+ AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
+ AHCI_HFLAG_NO_HOTPLUG = (1 << 7), /* ignore PxSERR.DIAG.N */
+ AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
/* ap->flags bits */
- AHCI_FLAG_NO_HOTPLUG = (1 << 24), /* ignore PxSERR.DIAG.N */
AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
- ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
- AHCI_LFLAG_COMMON = ATA_LFLAG_SKIP_D2H_BSY,
+ ATA_FLAG_ACPI_SATA | ATA_FLAG_AN |
+ ATA_FLAG_IPM,
+
+ ICH_MAP = 0x90, /* ICH MAP register */
};
struct ahci_cmd_hdr {
- u32 opts;
- u32 status;
- u32 tbl_addr;
- u32 tbl_addr_hi;
- u32 reserved[4];
+ __le32 opts;
+ __le32 status;
+ __le32 tbl_addr;
+ __le32 tbl_addr_hi;
+ __le32 reserved[4];
};
struct ahci_sg {
- u32 addr;
- u32 addr_hi;
- u32 reserved;
- u32 flags_size;
+ __le32 addr;
+ __le32 addr_hi;
+ __le32 reserved;
+ __le32 flags_size;
};
struct ahci_host_priv {
static int ahci_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val);
static int ahci_scr_write(struct ata_port *ap, unsigned int sc_reg, u32 val);
-static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
-static void ahci_irq_clear(struct ata_port *ap);
+static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc);
static int ahci_port_start(struct ata_port *ap);
static void ahci_port_stop(struct ata_port *ap);
-static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
static void ahci_qc_prep(struct ata_queued_cmd *qc);
-static u8 ahci_check_status(struct ata_port *ap);
static void ahci_freeze(struct ata_port *ap);
static void ahci_thaw(struct ata_port *ap);
static void ahci_pmp_attach(struct ata_port *ap);
static void ahci_pmp_detach(struct ata_port *ap);
-static int ahci_pmp_read(struct ata_device *dev, int pmp, int reg, u32 *r_val);
-static int ahci_pmp_write(struct ata_device *dev, int pmp, int reg, u32 val);
+static int ahci_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static int ahci_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
+static void ahci_postreset(struct ata_link *link, unsigned int *class);
+static int ahci_pmp_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
static void ahci_error_handler(struct ata_port *ap);
-static void ahci_vt8251_error_handler(struct ata_port *ap);
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
static int ahci_port_resume(struct ata_port *ap);
+static void ahci_dev_config(struct ata_device *dev);
static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl);
static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
u32 opts);
static int ahci_pci_device_resume(struct pci_dev *pdev);
#endif
+static struct class_device_attribute *ahci_shost_attrs[] = {
+ &class_device_attr_link_power_management_policy,
+ NULL
+};
+
static struct scsi_host_template ahci_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .change_queue_depth = ata_scsi_change_queue_depth,
+ ATA_NCQ_SHT(DRV_NAME),
.can_queue = AHCI_MAX_CMDS - 1,
- .this_id = ATA_SHT_THIS_ID,
.sg_tablesize = AHCI_MAX_SG,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = AHCI_USE_CLUSTERING,
- .proc_name = DRV_NAME,
.dma_boundary = AHCI_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .slave_destroy = ata_scsi_slave_destroy,
- .bios_param = ata_std_bios_param,
+ .shost_attrs = ahci_shost_attrs,
};
-static const struct ata_port_operations ahci_ops = {
- .check_status = ahci_check_status,
- .check_altstatus = ahci_check_status,
- .dev_select = ata_noop_dev_select,
-
- .tf_read = ahci_tf_read,
+static struct ata_port_operations ahci_ops = {
+ .inherits = &sata_pmp_port_ops,
.qc_defer = sata_pmp_qc_defer_cmd_switch,
.qc_prep = ahci_qc_prep,
.qc_issue = ahci_qc_issue,
-
- .irq_clear = ahci_irq_clear,
-
- .scr_read = ahci_scr_read,
- .scr_write = ahci_scr_write,
+ .qc_fill_rtf = ahci_qc_fill_rtf,
.freeze = ahci_freeze,
.thaw = ahci_thaw,
-
+ .softreset = ahci_softreset,
+ .hardreset = ahci_hardreset,
+ .postreset = ahci_postreset,
+ .pmp_softreset = ahci_pmp_softreset,
.error_handler = ahci_error_handler,
.post_internal_cmd = ahci_post_internal_cmd,
+ .dev_config = ahci_dev_config,
+ .scr_read = ahci_scr_read,
+ .scr_write = ahci_scr_write,
.pmp_attach = ahci_pmp_attach,
.pmp_detach = ahci_pmp_detach,
- .pmp_read = ahci_pmp_read,
- .pmp_write = ahci_pmp_write,
+ .enable_pm = ahci_enable_alpm,
+ .disable_pm = ahci_disable_alpm,
#ifdef CONFIG_PM
.port_suspend = ahci_port_suspend,
.port_resume = ahci_port_resume,
#endif
-
.port_start = ahci_port_start,
.port_stop = ahci_port_stop,
};
-static const struct ata_port_operations ahci_vt8251_ops = {
- .check_status = ahci_check_status,
- .check_altstatus = ahci_check_status,
- .dev_select = ata_noop_dev_select,
-
- .tf_read = ahci_tf_read,
-
- .qc_defer = sata_pmp_qc_defer_cmd_switch,
- .qc_prep = ahci_qc_prep,
- .qc_issue = ahci_qc_issue,
-
- .irq_clear = ahci_irq_clear,
-
- .scr_read = ahci_scr_read,
- .scr_write = ahci_scr_write,
-
- .freeze = ahci_freeze,
- .thaw = ahci_thaw,
-
- .error_handler = ahci_vt8251_error_handler,
- .post_internal_cmd = ahci_post_internal_cmd,
-
- .pmp_attach = ahci_pmp_attach,
- .pmp_detach = ahci_pmp_detach,
- .pmp_read = ahci_pmp_read,
- .pmp_write = ahci_pmp_write,
-
-#ifdef CONFIG_PM
- .port_suspend = ahci_port_suspend,
- .port_resume = ahci_port_resume,
-#endif
+static struct ata_port_operations ahci_vt8251_ops = {
+ .inherits = &ahci_ops,
+ .hardreset = ahci_vt8251_hardreset,
+};
- .port_start = ahci_port_start,
- .port_stop = ahci_port_stop,
+static struct ata_port_operations ahci_p5wdh_ops = {
+ .inherits = &ahci_ops,
+ .hardreset = ahci_p5wdh_hardreset,
};
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
/* board_ahci */
{
.flags = AHCI_FLAG_COMMON,
- .link_flags = AHCI_LFLAG_COMMON,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
},
/* board_ahci_vt8251 */
{
- AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ),
+ AHCI_HFLAGS (AHCI_HFLAG_NO_NCQ | AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
- .link_flags = AHCI_LFLAG_COMMON | ATA_LFLAG_HRST_TO_RESUME,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_vt8251_ops,
{
AHCI_HFLAGS (AHCI_HFLAG_IGN_IRQ_IF_ERR),
.flags = AHCI_FLAG_COMMON,
- .link_flags = AHCI_LFLAG_COMMON,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
/* board_ahci_sb600 */
{
AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL |
- AHCI_HFLAG_32BIT_ONLY),
+ AHCI_HFLAG_32BIT_ONLY |
+ AHCI_HFLAG_SECT255 | AHCI_HFLAG_NO_PMP),
.flags = AHCI_FLAG_COMMON,
- .link_flags = AHCI_LFLAG_COMMON,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
AHCI_HFLAG_MV_PATA),
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA,
- .link_flags = AHCI_LFLAG_COMMON,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_ops,
+ },
+ /* board_ahci_sb700 */
+ {
+ AHCI_HFLAGS (AHCI_HFLAG_IGN_SERR_INTERNAL |
+ AHCI_HFLAG_NO_PMP),
+ .flags = AHCI_FLAG_COMMON,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_ops,
{ PCI_VDEVICE(INTEL, 0x294e), board_ahci }, /* ICH9M */
{ PCI_VDEVICE(INTEL, 0x502a), board_ahci }, /* Tolapai */
{ PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */
+ { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
+ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */
/* JMicron 360/1/3/5/6, match class to avoid IDE function */
{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
/* ATI */
{ PCI_VDEVICE(ATI, 0x4380), board_ahci_sb600 }, /* ATI SB600 */
- { PCI_VDEVICE(ATI, 0x4390), board_ahci_sb600 }, /* ATI SB700/800 */
- { PCI_VDEVICE(ATI, 0x4391), board_ahci_sb600 }, /* ATI SB700/800 */
- { PCI_VDEVICE(ATI, 0x4392), board_ahci_sb600 }, /* ATI SB700/800 */
- { PCI_VDEVICE(ATI, 0x4393), board_ahci_sb600 }, /* ATI SB700/800 */
- { PCI_VDEVICE(ATI, 0x4394), board_ahci_sb600 }, /* ATI SB700/800 */
- { PCI_VDEVICE(ATI, 0x4395), board_ahci_sb600 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4390), board_ahci_sb700 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4391), board_ahci_sb700 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4392), board_ahci_sb700 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4393), board_ahci_sb700 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4394), board_ahci_sb700 }, /* ATI SB700/800 */
+ { PCI_VDEVICE(ATI, 0x4395), board_ahci_sb700 }, /* ATI SB700/800 */
/* VIA */
{ PCI_VDEVICE(VIA, 0x3349), board_ahci_vt8251 }, /* VIA VT8251 */
{ PCI_VDEVICE(NVIDIA, 0x0ad9), board_ahci }, /* MCP77 */
{ PCI_VDEVICE(NVIDIA, 0x0ada), board_ahci }, /* MCP77 */
{ PCI_VDEVICE(NVIDIA, 0x0adb), board_ahci }, /* MCP77 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab4), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab5), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab6), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab7), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab8), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0ab9), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0aba), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0abb), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0abc), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0abd), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0abe), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0abf), board_ahci }, /* MCP79 */
+ { PCI_VDEVICE(NVIDIA, 0x0bc8), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bc9), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bca), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bcb), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bcc), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bcd), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bce), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bcf), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bd0), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bd1), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bd2), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0bd3), board_ahci }, /* MCP7B */
/* SiS */
{ PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */
/* Marvell */
{ PCI_VDEVICE(MARVELL, 0x6145), board_ahci_mv }, /* 6145 */
+ { PCI_VDEVICE(MARVELL, 0x6121), board_ahci_mv }, /* 6121 */
/* Generic, PCI class code for AHCI */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
return __ahci_port_base(ap->host, ap->port_no);
}
+static void ahci_enable_ahci(void __iomem *mmio)
+{
+ u32 tmp;
+
+ /* turn on AHCI_EN */
+ tmp = readl(mmio + HOST_CTL);
+ if (!(tmp & HOST_AHCI_EN)) {
+ tmp |= HOST_AHCI_EN;
+ writel(tmp, mmio + HOST_CTL);
+ tmp = readl(mmio + HOST_CTL); /* flush && sanity check */
+ WARN_ON(!(tmp & HOST_AHCI_EN));
+ }
+}
+
/**
* ahci_save_initial_config - Save and fixup initial config values
* @pdev: target PCI device
void __iomem *mmio = pcim_iomap_table(pdev)[AHCI_PCI_BAR];
u32 cap, port_map;
int i;
+ int mv;
+
+ /* make sure AHCI mode is enabled before accessing CAP */
+ ahci_enable_ahci(mmio);
/* Values prefixed with saved_ are written back to host after
* reset. Values without are used for driver operation.
cap &= ~HOST_CAP_NCQ;
}
+ if ((cap & HOST_CAP_PMP) && (hpriv->flags & AHCI_HFLAG_NO_PMP)) {
+ dev_printk(KERN_INFO, &pdev->dev,
+ "controller can't do PMP, turning off CAP_PMP\n");
+ cap &= ~HOST_CAP_PMP;
+ }
+
/*
* Temporary Marvell 6145 hack: PATA port presence
* is asserted through the standard AHCI port
* presence register, as bit 4 (counting from 0)
*/
if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
+ if (pdev->device == 0x6121)
+ mv = 0x3;
+ else
+ mv = 0xf;
dev_printk(KERN_ERR, &pdev->dev,
"MV_AHCI HACK: port_map %x -> %x\n",
- hpriv->port_map,
- hpriv->port_map & 0xf);
+ port_map,
+ port_map & mv);
- port_map &= 0xf;
+ port_map &= mv;
}
/* cross check port_map and cap.n_ports */
if (port_map) {
- u32 tmp_port_map = port_map;
- int n_ports = ahci_nr_ports(cap);
+ int map_ports = 0;
- for (i = 0; i < AHCI_MAX_PORTS && n_ports; i++) {
- if (tmp_port_map & (1 << i)) {
- n_ports--;
- tmp_port_map &= ~(1 << i);
- }
- }
+ for (i = 0; i < AHCI_MAX_PORTS; i++)
+ if (port_map & (1 << i))
+ map_ports++;
- /* If n_ports and port_map are inconsistent, whine and
- * clear port_map and let it be generated from n_ports.
+ /* If PI has more ports than n_ports, whine, clear
+ * port_map and let it be generated from n_ports.
*/
- if (n_ports || tmp_port_map) {
+ if (map_ports > ahci_nr_ports(cap)) {
dev_printk(KERN_WARNING, &pdev->dev,
- "nr_ports (%u) and implemented port map "
- "(0x%x) don't match, using nr_ports\n",
- ahci_nr_ports(cap), port_map);
+ "implemented port map (0x%x) contains more "
+ "ports than nr_ports (%u), using nr_ports\n",
+ port_map, ahci_nr_ports(cap));
port_map = 0;
}
}
/* wait for engine to stop. This could be as long as 500 msec */
tmp = ata_wait_register(port_mmio + PORT_CMD,
- PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
+ PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
if (tmp & PORT_CMD_LIST_ON)
return -EIO;
writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
}
+static void ahci_disable_alpm(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd;
+ struct ahci_port_priv *pp = ap->private_data;
+
+ /* IPM bits should be disabled by libata-core */
+ /* get the existing command bits */
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* disable ALPM and ASP */
+ cmd &= ~PORT_CMD_ASP;
+ cmd &= ~PORT_CMD_ALPE;
+
+ /* force the interface back to active */
+ cmd |= PORT_CMD_ICC_ACTIVE;
+
+ /* write out new cmd value */
+ writel(cmd, port_mmio + PORT_CMD);
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* wait 10ms to be sure we've come out of any low power state */
+ msleep(10);
+
+ /* clear out any PhyRdy stuff from interrupt status */
+ writel(PORT_IRQ_PHYRDY, port_mmio + PORT_IRQ_STAT);
+
+ /* go ahead and clean out PhyRdy Change from Serror too */
+ ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18)));
+
+ /*
+ * Clear flag to indicate that we should ignore all PhyRdy
+ * state changes
+ */
+ hpriv->flags &= ~AHCI_HFLAG_NO_HOTPLUG;
+
+ /*
+ * Enable interrupts on Phy Ready.
+ */
+ pp->intr_mask |= PORT_IRQ_PHYRDY;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+ /*
+ * don't change the link pm policy - we can be called
+ * just to turn of link pm temporarily
+ */
+}
+
+static int ahci_enable_alpm(struct ata_port *ap,
+ enum link_pm policy)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ u32 cmd;
+ struct ahci_port_priv *pp = ap->private_data;
+ u32 asp;
+
+ /* Make sure the host is capable of link power management */
+ if (!(hpriv->cap & HOST_CAP_ALPM))
+ return -EINVAL;
+
+ switch (policy) {
+ case MAX_PERFORMANCE:
+ case NOT_AVAILABLE:
+ /*
+ * if we came here with NOT_AVAILABLE,
+ * it just means this is the first time we
+ * have tried to enable - default to max performance,
+ * and let the user go to lower power modes on request.
+ */
+ ahci_disable_alpm(ap);
+ return 0;
+ case MIN_POWER:
+ /* configure HBA to enter SLUMBER */
+ asp = PORT_CMD_ASP;
+ break;
+ case MEDIUM_POWER:
+ /* configure HBA to enter PARTIAL */
+ asp = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /*
+ * Disable interrupts on Phy Ready. This keeps us from
+ * getting woken up due to spurious phy ready interrupts
+ * TBD - Hot plug should be done via polling now, is
+ * that even supported?
+ */
+ pp->intr_mask &= ~PORT_IRQ_PHYRDY;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
+
+ /*
+ * Set a flag to indicate that we should ignore all PhyRdy
+ * state changes since these can happen now whenever we
+ * change link state
+ */
+ hpriv->flags |= AHCI_HFLAG_NO_HOTPLUG;
+
+ /* get the existing command bits */
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /*
+ * Set ASP based on Policy
+ */
+ cmd |= asp;
+
+ /*
+ * Setting this bit will instruct the HBA to aggressively
+ * enter a lower power link state when it's appropriate and
+ * based on the value set above for ASP
+ */
+ cmd |= PORT_CMD_ALPE;
+
+ /* write out new cmd value */
+ writel(cmd, port_mmio + PORT_CMD);
+ cmd = readl(port_mmio + PORT_CMD);
+
+ /* IPM bits should be set by libata-core */
+ return 0;
+}
+
#ifdef CONFIG_PM
static void ahci_power_down(struct ata_port *ap)
{
static int ahci_reset_controller(struct ata_host *host)
{
struct pci_dev *pdev = to_pci_dev(host->dev);
+ struct ahci_host_priv *hpriv = host->private_data;
void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
u32 tmp;
/* we must be in AHCI mode, before using anything
* AHCI-specific, such as HOST_RESET.
*/
- tmp = readl(mmio + HOST_CTL);
- if (!(tmp & HOST_AHCI_EN))
- writel(tmp | HOST_AHCI_EN, mmio + HOST_CTL);
+ ahci_enable_ahci(mmio);
/* global controller reset */
- if ((tmp & HOST_RESET) == 0) {
- writel(tmp | HOST_RESET, mmio + HOST_CTL);
- readl(mmio + HOST_CTL); /* flush */
- }
+ if (!ahci_skip_host_reset) {
+ tmp = readl(mmio + HOST_CTL);
+ if ((tmp & HOST_RESET) == 0) {
+ writel(tmp | HOST_RESET, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+ }
- /* reset must complete within 1 second, or
- * the hardware should be considered fried.
- */
- ssleep(1);
+ /* reset must complete within 1 second, or
+ * the hardware should be considered fried.
+ */
+ ssleep(1);
- tmp = readl(mmio + HOST_CTL);
- if (tmp & HOST_RESET) {
- dev_printk(KERN_ERR, host->dev,
- "controller reset failed (0x%x)\n", tmp);
- return -EIO;
- }
+ tmp = readl(mmio + HOST_CTL);
+ if (tmp & HOST_RESET) {
+ dev_printk(KERN_ERR, host->dev,
+ "controller reset failed (0x%x)\n", tmp);
+ return -EIO;
+ }
- /* turn on AHCI mode */
- writel(HOST_AHCI_EN, mmio + HOST_CTL);
- (void) readl(mmio + HOST_CTL); /* flush */
+ /* turn on AHCI mode */
+ ahci_enable_ahci(mmio);
- /* some registers might be cleared on reset. restore initial values */
- ahci_restore_initial_config(host);
+ /* Some registers might be cleared on reset. Restore
+ * initial values.
+ */
+ ahci_restore_initial_config(host);
+ } else
+ dev_printk(KERN_INFO, host->dev,
+ "skipping global host reset\n");
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
u16 tmp16;
/* configure PCS */
pci_read_config_word(pdev, 0x92, &tmp16);
- tmp16 |= 0xf;
- pci_write_config_word(pdev, 0x92, tmp16);
+ if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
+ tmp16 |= hpriv->port_map;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
}
return 0;
int i;
void __iomem *port_mmio;
u32 tmp;
+ int mv;
if (hpriv->flags & AHCI_HFLAG_MV_PATA) {
- port_mmio = __ahci_port_base(host, 4);
+ if (pdev->device == 0x6121)
+ mv = 2;
+ else
+ mv = 4;
+ port_mmio = __ahci_port_base(host, mv);
writel(0, port_mmio + PORT_IRQ_MASK);
VPRINTK("HOST_CTL 0x%x\n", tmp);
}
+static void ahci_dev_config(struct ata_device *dev)
+{
+ struct ahci_host_priv *hpriv = dev->link->ap->host->private_data;
+
+ if (hpriv->flags & AHCI_HFLAG_SECT255) {
+ dev->max_sectors = 255;
+ ata_dev_printk(dev, KERN_INFO,
+ "SB600 AHCI: limiting to 255 sectors per cmd\n");
+ }
+}
+
static unsigned int ahci_dev_classify(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
static int ahci_kick_engine(struct ata_port *ap, int force_restart)
{
- void __iomem *port_mmio = ap->ioaddr.cmd_addr;
+ void __iomem *port_mmio = ahci_port_base(ap);
struct ahci_host_priv *hpriv = ap->host->private_data;
+ u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
u32 tmp;
int busy, rc;
/* do we need to kick the port? */
- busy = ahci_check_status(ap) & (ATA_BUSY | ATA_DRQ);
+ busy = status & (ATA_BUSY | ATA_DRQ);
if (!busy && !force_restart)
return 0;
return 0;
}
+static int ahci_check_ready(struct ata_link *link)
+{
+ void __iomem *port_mmio = ahci_port_base(link->ap);
+ u8 status = readl(port_mmio + PORT_TFDATA) & 0xFF;
+
+ if (!(status & ATA_BUSY))
+ return 1;
+ return 0;
+}
+
static int ahci_do_softreset(struct ata_link *link, unsigned int *class,
int pmp, unsigned long deadline)
{
/* prepare for SRST (AHCI-1.1 10.4.1) */
rc = ahci_kick_engine(ap, 1);
- if (rc)
+ if (rc && rc != -EOPNOTSUPP)
ata_link_printk(link, KERN_WARNING,
- "failed to reset engine (errno=%d)", rc);
+ "failed to reset engine (errno=%d)\n", rc);
ata_tf_init(link->device, &tf);
tf.ctl &= ~ATA_SRST;
ahci_exec_polled_cmd(ap, pmp, &tf, 0, 0, 0);
- /* spec mandates ">= 2ms" before checking status.
- * We wait 150ms, because that was the magic delay used for
- * ATAPI devices in Hale Landis's ATADRVR, for the period of time
- * between when the ATA command register is written, and then
- * status is checked. Because waiting for "a while" before
- * checking status is fine, post SRST, we perform this magic
- * delay here as well.
- */
- msleep(150);
-
- rc = ata_wait_ready(ap, deadline);
+ /* wait for link to become ready */
+ rc = ata_wait_after_reset(link, deadline, ahci_check_ready);
/* link occupied, -ENODEV too is an error */
if (rc) {
reason = "device not ready";
static int ahci_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
struct ata_port *ap = link->ap;
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
struct ata_taskfile tf;
+ bool online;
int rc;
DPRINTK("ENTER\n");
tf.command = 0x80;
ata_tf_to_fis(&tf, 0, 0, d2h_fis);
- rc = sata_std_hardreset(link, class, deadline);
+ rc = sata_link_hardreset(link, timing, deadline, &online,
+ ahci_check_ready);
ahci_start_engine(ap);
- if (rc == 0 && ata_link_online(link))
+ if (online)
*class = ahci_dev_classify(ap);
- if (rc != -EAGAIN && *class == ATA_DEV_UNKNOWN)
- *class = ATA_DEV_NONE;
DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
return rc;
unsigned long deadline)
{
struct ata_port *ap = link->ap;
- u32 serror;
+ bool online;
int rc;
DPRINTK("ENTER\n");
ahci_stop_engine(ap);
rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
- deadline);
-
- /* vt8251 needs SError cleared for the port to operate */
- ahci_scr_read(ap, SCR_ERROR, &serror);
- ahci_scr_write(ap, SCR_ERROR, serror);
+ deadline, &online, NULL);
ahci_start_engine(ap);
/* vt8251 doesn't clear BSY on signature FIS reception,
* request follow-up softreset.
*/
- return rc ?: -EAGAIN;
+ return online ? -EAGAIN : rc;
+}
+
+static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ bool online;
+ int rc;
+
+ ahci_stop_engine(ap);
+
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+ rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
+ deadline, &online, NULL);
+
+ ahci_start_engine(ap);
+
+ /* The pseudo configuration device on SIMG4726 attached to
+ * ASUS P5W-DH Deluxe doesn't send signature FIS after
+ * hardreset if no device is attached to the first downstream
+ * port && the pseudo device locks up on SRST w/ PMP==0. To
+ * work around this, wait for !BSY only briefly. If BSY isn't
+ * cleared, perform CLO and proceed to IDENTIFY (achieved by
+ * ATA_LFLAG_NO_SRST and ATA_LFLAG_ASSUME_ATA).
+ *
+ * Wait for two seconds. Devices attached to downstream port
+ * which can't process the following IDENTIFY after this will
+ * have to be reset again. For most cases, this should
+ * suffice while making probing snappish enough.
+ */
+ if (online) {
+ rc = ata_wait_after_reset(link, jiffies + 2 * HZ,
+ ahci_check_ready);
+ if (rc)
+ ahci_kick_engine(ap, 0);
+ }
+ return rc;
}
static void ahci_postreset(struct ata_link *link, unsigned int *class)
return ahci_do_softreset(link, class, link->pmp, deadline);
}
-static u8 ahci_check_status(struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.cmd_addr;
-
- return readl(mmio + PORT_TFDATA) & 0xFF;
-}
-
-static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
-{
- struct ahci_port_priv *pp = ap->private_data;
- u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
-
- ata_tf_from_fis(d2h_fis, tf);
-}
-
static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl)
{
struct scatterlist *sg;
- struct ahci_sg *ahci_sg;
- unsigned int n_sg = 0;
+ struct ahci_sg *ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
+ unsigned int si;
VPRINTK("ENTER\n");
/*
* Next, the S/G list.
*/
- ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
- ata_for_each_sg(sg, qc) {
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
dma_addr_t addr = sg_dma_address(sg);
u32 sg_len = sg_dma_len(sg);
- ahci_sg->addr = cpu_to_le32(addr & 0xffffffff);
- ahci_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16);
- ahci_sg->flags_size = cpu_to_le32(sg_len - 1);
-
- ahci_sg++;
- n_sg++;
+ ahci_sg[si].addr = cpu_to_le32(addr & 0xffffffff);
+ ahci_sg[si].addr_hi = cpu_to_le32((addr >> 16) >> 16);
+ ahci_sg[si].flags_size = cpu_to_le32(sg_len - 1);
}
- return n_sg;
+ return si;
}
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ahci_port_priv *pp = ap->private_data;
- int is_atapi = is_atapi_taskfile(&qc->tf);
+ int is_atapi = ata_is_atapi(qc->tf.protocol);
void *cmd_tbl;
u32 opts;
const u32 cmd_fis_len = 5; /* five dwords */
u32 *unk = (u32 *)(pp->rx_fis + RX_FIS_UNK);
active_ehi->err_mask |= AC_ERR_HSM;
- active_ehi->action |= ATA_EH_SOFTRESET;
+ active_ehi->action |= ATA_EH_RESET;
ata_ehi_push_desc(active_ehi,
"unknown FIS %08x %08x %08x %08x" ,
unk[0], unk[1], unk[2], unk[3]);
if (ap->nr_pmp_links && (irq_stat & PORT_IRQ_BAD_PMP)) {
active_ehi->err_mask |= AC_ERR_HSM;
- active_ehi->action |= ATA_EH_SOFTRESET;
+ active_ehi->action |= ATA_EH_RESET;
ata_ehi_push_desc(active_ehi, "incorrect PMP");
}
if (irq_stat & (PORT_IRQ_HBUS_ERR | PORT_IRQ_HBUS_DATA_ERR)) {
host_ehi->err_mask |= AC_ERR_HOST_BUS;
- host_ehi->action |= ATA_EH_SOFTRESET;
+ host_ehi->action |= ATA_EH_RESET;
ata_ehi_push_desc(host_ehi, "host bus error");
}
if (irq_stat & PORT_IRQ_IF_ERR) {
host_ehi->err_mask |= AC_ERR_ATA_BUS;
- host_ehi->action |= ATA_EH_SOFTRESET;
+ host_ehi->action |= ATA_EH_RESET;
ata_ehi_push_desc(host_ehi, "interface fatal error");
}
static void ahci_port_intr(struct ata_port *ap)
{
- void __iomem *port_mmio = ap->ioaddr.cmd_addr;
+ void __iomem *port_mmio = ahci_port_base(ap);
struct ata_eh_info *ehi = &ap->link.eh_info;
struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ int resetting = !!(ap->pflags & ATA_PFLAG_RESETTING);
u32 status, qc_active;
- int rc, known_irq = 0;
+ int rc;
status = readl(port_mmio + PORT_IRQ_STAT);
writel(status, port_mmio + PORT_IRQ_STAT);
+ /* ignore BAD_PMP while resetting */
+ if (unlikely(resetting))
+ status &= ~PORT_IRQ_BAD_PMP;
+
+ /* If we are getting PhyRdy, this is
+ * just a power state change, we should
+ * clear out this, plus the PhyRdy/Comm
+ * Wake bits from Serror
+ */
+ if ((hpriv->flags & AHCI_HFLAG_NO_HOTPLUG) &&
+ (status & PORT_IRQ_PHYRDY)) {
+ status &= ~PORT_IRQ_PHYRDY;
+ ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18)));
+ }
+
if (unlikely(status & PORT_IRQ_ERROR)) {
ahci_error_intr(ap, status);
return;
}
if (status & PORT_IRQ_SDB_FIS) {
- /* If the 'N' bit in word 0 of the FIS is set, we just
- * received asynchronous notification. Tell libata
- * about it. Note that as the SDB FIS itself is
- * accessible, SNotification can be emulated by the
- * driver but don't bother for the time being.
+ /* If SNotification is available, leave notification
+ * handling to sata_async_notification(). If not,
+ * emulate it by snooping SDB FIS RX area.
+ *
+ * Snooping FIS RX area is probably cheaper than
+ * poking SNotification but some constrollers which
+ * implement SNotification, ICH9 for example, don't
+ * store AN SDB FIS into receive area.
*/
- const __le32 *f = pp->rx_fis + RX_FIS_SDB;
- u32 f0 = le32_to_cpu(f[0]);
-
- if (f0 & (1 << 15))
+ if (hpriv->cap & HOST_CAP_SNTF)
sata_async_notification(ap);
+ else {
+ /* If the 'N' bit in word 0 of the FIS is set,
+ * we just received asynchronous notification.
+ * Tell libata about it.
+ */
+ const __le32 *f = pp->rx_fis + RX_FIS_SDB;
+ u32 f0 = le32_to_cpu(f[0]);
+
+ if (f0 & (1 << 15))
+ sata_async_notification(ap);
+ }
}
/* pp->active_link is valid iff any command is in flight */
else
qc_active = readl(port_mmio + PORT_CMD_ISSUE);
- rc = ata_qc_complete_multiple(ap, qc_active, NULL);
- if (rc > 0)
- return;
- if (rc < 0) {
+ rc = ata_qc_complete_multiple(ap, qc_active);
+
+ /* while resetting, invalid completions are expected */
+ if (unlikely(rc < 0 && !resetting)) {
ehi->err_mask |= AC_ERR_HSM;
- ehi->action |= ATA_EH_SOFTRESET;
+ ehi->action |= ATA_EH_RESET;
ata_port_freeze(ap);
- return;
}
-
- /* hmmm... a spurious interupt */
-
- /* if !NCQ, ignore. No modern ATA device has broken HSM
- * implementation for non-NCQ commands.
- */
- if (!ap->link.sactive)
- return;
-
- if (status & PORT_IRQ_D2H_REG_FIS) {
- if (!pp->ncq_saw_d2h)
- ata_port_printk(ap, KERN_INFO,
- "D2H reg with I during NCQ, "
- "this message won't be printed again\n");
- pp->ncq_saw_d2h = 1;
- known_irq = 1;
- }
-
- if (status & PORT_IRQ_DMAS_FIS) {
- if (!pp->ncq_saw_dmas)
- ata_port_printk(ap, KERN_INFO,
- "DMAS FIS during NCQ, "
- "this message won't be printed again\n");
- pp->ncq_saw_dmas = 1;
- known_irq = 1;
- }
-
- if (status & PORT_IRQ_SDB_FIS) {
- const __le32 *f = pp->rx_fis + RX_FIS_SDB;
-
- if (le32_to_cpu(f[1])) {
- /* SDB FIS containing spurious completions
- * might be dangerous, whine and fail commands
- * with HSM violation. EH will turn off NCQ
- * after several such failures.
- */
- ata_ehi_push_desc(ehi,
- "spurious completions during NCQ "
- "issue=0x%x SAct=0x%x FIS=%08x:%08x",
- readl(port_mmio + PORT_CMD_ISSUE),
- readl(port_mmio + PORT_SCR_ACT),
- le32_to_cpu(f[0]), le32_to_cpu(f[1]));
- ehi->err_mask |= AC_ERR_HSM;
- ehi->action |= ATA_EH_SOFTRESET;
- ata_port_freeze(ap);
- } else {
- if (!pp->ncq_saw_sdb)
- ata_port_printk(ap, KERN_INFO,
- "spurious SDB FIS %08x:%08x during NCQ, "
- "this message won't be printed again\n",
- le32_to_cpu(f[0]), le32_to_cpu(f[1]));
- pp->ncq_saw_sdb = 1;
- }
- known_irq = 1;
- }
-
- if (!known_irq)
- ata_port_printk(ap, KERN_INFO, "spurious interrupt "
- "(irq_stat 0x%x active_tag 0x%x sactive 0x%x)\n",
- status, ap->link.active_tag, ap->link.sactive);
-}
-
-static void ahci_irq_clear(struct ata_port *ap)
-{
- /* TODO */
}
static irqreturn_t ahci_interrupt(int irq, void *dev_instance)
if (!irq_stat)
return IRQ_NONE;
- spin_lock(&host->lock);
+ spin_lock(&host->lock);
- for (i = 0; i < host->n_ports; i++) {
+ for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap;
if (!(irq_stat & (1 << i)))
return 0;
}
+static bool ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
+{
+ struct ahci_port_priv *pp = qc->ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+
+ ata_tf_from_fis(d2h_fis, &qc->result_tf);
+ return true;
+}
+
static void ahci_freeze(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
writel(tmp, port_mmio + PORT_IRQ_STAT);
writel(1 << ap->port_no, mmio + HOST_IRQ_STAT);
- /* turn IRQ back on, ignore BAD_PMP if PMP isn't attached */
- tmp = pp->intr_mask;
- if (!ap->nr_pmp_links)
- tmp &= ~PORT_IRQ_BAD_PMP;
- writel(tmp, port_mmio + PORT_IRQ_MASK);
+ /* turn IRQ back on */
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
}
static void ahci_error_handler(struct ata_port *ap)
ahci_start_engine(ap);
}
- /* perform recovery */
- sata_pmp_do_eh(ap, ata_std_prereset, ahci_softreset,
- ahci_hardreset, ahci_postreset,
- sata_pmp_std_prereset, ahci_pmp_softreset,
- sata_pmp_std_hardreset, sata_pmp_std_postreset);
-}
-
-static void ahci_vt8251_error_handler(struct ata_port *ap)
-{
- if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
- /* restart engine */
- ahci_stop_engine(ap);
- ahci_start_engine(ap);
- }
-
- /* perform recovery */
- ata_do_eh(ap, ata_std_prereset, ahci_softreset, ahci_vt8251_hardreset,
- ahci_postreset);
+ sata_pmp_error_handler(ap);
}
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
static void ahci_pmp_attach(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_port_priv *pp = ap->private_data;
u32 cmd;
cmd = readl(port_mmio + PORT_CMD);
cmd |= PORT_CMD_PMP;
writel(cmd, port_mmio + PORT_CMD);
+
+ pp->intr_mask |= PORT_IRQ_BAD_PMP;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
}
static void ahci_pmp_detach(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
- struct ahci_host_priv *hpriv = ap->host->private_data;
- unsigned long flags;
+ struct ahci_port_priv *pp = ap->private_data;
u32 cmd;
cmd = readl(port_mmio + PORT_CMD);
cmd &= ~PORT_CMD_PMP;
writel(cmd, port_mmio + PORT_CMD);
- if (hpriv->cap & HOST_CAP_NCQ) {
- spin_lock_irqsave(ap->lock, flags);
- ap->flags |= ATA_FLAG_NCQ;
- spin_unlock_irqrestore(ap->lock, flags);
- }
-}
-
-static int ahci_pmp_read(struct ata_device *dev, int pmp, int reg, u32 *r_val)
-{
- struct ata_port *ap = dev->link->ap;
- struct ata_taskfile tf;
- int rc;
-
- ahci_kick_engine(ap, 0);
-
- sata_pmp_read_init_tf(&tf, dev, pmp, reg);
- rc = ahci_exec_polled_cmd(ap, SATA_PMP_CTRL_PORT, &tf, 1, 0,
- SATA_PMP_SCR_TIMEOUT);
- if (rc == 0) {
- ahci_tf_read(ap, &tf);
- *r_val = sata_pmp_read_val(&tf);
- }
- return rc;
-}
-
-static int ahci_pmp_write(struct ata_device *dev, int pmp, int reg, u32 val)
-{
- struct ata_port *ap = dev->link->ap;
- struct ata_taskfile tf;
-
- ahci_kick_engine(ap, 0);
-
- sata_pmp_write_init_tf(&tf, dev, pmp, reg, val);
- return ahci_exec_polled_cmd(ap, SATA_PMP_CTRL_PORT, &tf, 1, 0,
- SATA_PMP_SCR_TIMEOUT);
+ pp->intr_mask &= ~PORT_IRQ_BAD_PMP;
+ writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK);
}
static int ahci_port_resume(struct ata_port *ap)
void __iomem *mmio = host->iomap[AHCI_PCI_BAR];
u32 ctl;
- if (mesg.event == PM_EVENT_SUSPEND) {
+ if (mesg.event & PM_EVENT_SLEEP) {
/* AHCI spec rev1.1 section 8.3.3:
* Software must disable interrupts prior to requesting a
* transition of the HBA to D3 state.
struct ahci_port_priv *pp;
void *mem;
dma_addr_t mem_dma;
- int rc;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
- rc = ata_pad_alloc(ap, dev);
- if (rc)
- return rc;
-
mem = dmam_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma,
GFP_KERNEL);
if (!mem)
pp->cmd_tbl_dma = mem_dma;
/*
- * Save off initial list of interrupts to be enabled.
- * This could be changed later
- */
+ * Save off initial list of interrupts to be enabled.
+ * This could be changed later
+ */
pp->intr_mask = DEF_PORT_IRQ;
ap->private_data = pp;
dev_printk(KERN_INFO, &pdev->dev,
"AHCI %02x%02x.%02x%02x "
"%u slots %u ports %s Gbps 0x%x impl %s mode\n"
- ,
+ ,
- (vers >> 24) & 0xff,
- (vers >> 16) & 0xff,
- (vers >> 8) & 0xff,
- vers & 0xff,
+ (vers >> 24) & 0xff,
+ (vers >> 16) & 0xff,
+ (vers >> 8) & 0xff,
+ vers & 0xff,
((cap >> 8) & 0x1f) + 1,
(cap & 0x1f) + 1,
"flags: "
"%s%s%s%s%s%s%s"
"%s%s%s%s%s%s%s\n"
- ,
+ ,
cap & (1 << 31) ? "64bit " : "",
cap & (1 << 30) ? "ncq " : "",
);
}
+/* On ASUS P5W DH Deluxe, the second port of PCI device 00:1f.2 is
+ * hardwired to on-board SIMG 4726. The chipset is ICH8 and doesn't
+ * support PMP and the 4726 either directly exports the device
+ * attached to the first downstream port or acts as a hardware storage
+ * controller and emulate a single ATA device (can be RAID 0/1 or some
+ * other configuration).
+ *
+ * When there's no device attached to the first downstream port of the
+ * 4726, "Config Disk" appears, which is a pseudo ATA device to
+ * configure the 4726. However, ATA emulation of the device is very
+ * lame. It doesn't send signature D2H Reg FIS after the initial
+ * hardreset, pukes on SRST w/ PMP==0 and has bunch of other issues.
+ *
+ * The following function works around the problem by always using
+ * hardreset on the port and not depending on receiving signature FIS
+ * afterward. If signature FIS isn't received soon, ATA class is
+ * assumed without follow-up softreset.
+ */
+static void ahci_p5wdh_workaround(struct ata_host *host)
+{
+ static struct dmi_system_id sysids[] = {
+ {
+ .ident = "P5W DH Deluxe",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR,
+ "ASUSTEK COMPUTER INC"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "P5W DH Deluxe"),
+ },
+ },
+ { }
+ };
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+
+ if (pdev->bus->number == 0 && pdev->devfn == PCI_DEVFN(0x1f, 2) &&
+ dmi_check_system(sysids)) {
+ struct ata_port *ap = host->ports[1];
+
+ dev_printk(KERN_INFO, &pdev->dev, "enabling ASUS P5W DH "
+ "Deluxe on-board SIMG4726 workaround\n");
+
+ ap->ops = &ahci_p5wdh_ops;
+ ap->link.flags |= ATA_LFLAG_NO_SRST | ATA_LFLAG_ASSUME_ATA;
+ }
+}
+
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
struct device *dev = &pdev->dev;
struct ahci_host_priv *hpriv;
struct ata_host *host;
- int i, rc;
+ int n_ports, i, rc;
VPRINTK("ENTER\n");
if (rc)
return rc;
- rc = pcim_iomap_regions(pdev, 1 << AHCI_PCI_BAR, DRV_NAME);
+ /* AHCI controllers often implement SFF compatible interface.
+ * Grab all PCI BARs just in case.
+ */
+ rc = pcim_iomap_regions_request_all(pdev, 1 << AHCI_PCI_BAR, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+ (pdev->device == 0x2652 || pdev->device == 0x2653)) {
+ u8 map;
+
+ /* ICH6s share the same PCI ID for both piix and ahci
+ * modes. Enabling ahci mode while MAP indicates
+ * combined mode is a bad idea. Yield to ata_piix.
+ */
+ pci_read_config_byte(pdev, ICH_MAP, &map);
+ if (map & 0x3) {
+ dev_printk(KERN_INFO, &pdev->dev, "controller is in "
+ "combined mode, can't enable AHCI mode\n");
+ return -ENODEV;
+ }
+ }
+
hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
if (hpriv->cap & HOST_CAP_PMP)
pi.flags |= ATA_FLAG_PMP;
- host = ata_host_alloc_pinfo(&pdev->dev, ppi, fls(hpriv->port_map));
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
if (!host)
return -ENOMEM;
host->iomap = pcim_iomap_table(pdev);
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
- void __iomem *port_mmio = ahci_port_base(ap);
ata_port_pbar_desc(ap, AHCI_PCI_BAR, -1, "abar");
ata_port_pbar_desc(ap, AHCI_PCI_BAR,
0x100 + ap->port_no * 0x80, "port");
- /* standard SATA port setup */
- if (hpriv->port_map & (1 << i))
- ap->ioaddr.cmd_addr = port_mmio;
+ /* set initial link pm policy */
+ ap->pm_policy = NOT_AVAILABLE;
/* disabled/not-implemented port */
- else
+ if (!(hpriv->port_map & (1 << i)))
ap->ops = &ata_dummy_port_ops;
}
+ /* apply workaround for ASUS P5W DH Deluxe mainboard */
+ ahci_p5wdh_workaround(host);
+
/* initialize adapter */
rc = ahci_configure_dma_masks(pdev, hpriv->cap & HOST_CAP_64);
if (rc)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff