# SATA/PATA driver configuration
#
-menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
-
-config ATA
- tristate "ATA device support"
+menuconfig ATA
+ tristate "Serial ATA and Parallel ATA drivers"
+ depends on HAS_IOMEM
+ depends on BLOCK
depends on !(M32R || M68K) || BROKEN
- depends on !SUN4 || BROKEN
select SCSI
---help---
If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
that "speaks" the ATA protocol, also called ATA controller),
because you will be asked for it.
+ NOTE: ATA enables basic SCSI support; *however*,
+ 'SCSI disk support', 'SCSI tape support', or
+ 'SCSI CDROM support' may also be needed,
+ depending on your hardware configuration.
+
if ATA
+config ATA_NONSTANDARD
+ bool
+ default n
+
+config ATA_VERBOSE_ERROR
+ bool "Verbose ATA error reporting"
+ default y
+ help
+ This option adds parsing of ATA command descriptions and error bits
+ in libata kernel output, making it easier to interpret.
+ This option will enlarge the kernel by approx. 6KB. Disable it only
+ if kernel size is more important than ease of debugging.
+
+ If unsure, say Y.
+
+config ATA_ACPI
+ bool "ATA ACPI Support"
+ depends on ACPI && PCI
+ default y
+ help
+ This option adds support for ATA-related ACPI objects.
+ These ACPI objects add the ability to retrieve taskfiles
+ from the ACPI BIOS and write them to the disk controller.
+ These objects may be related to performance, security,
+ power management, or other areas.
+ You can disable this at kernel boot time by using the
+ option libata.noacpi=1
+
+config SATA_PMP
+ bool "SATA Port Multiplier support"
+ default y
+ help
+ This option adds support for SATA Port Multipliers
+ (the SATA version of an ethernet hub, or SAS expander).
+
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
If unsure, say N.
+config SATA_SIL24
+ tristate "Silicon Image 3124/3132 SATA support"
+ depends on PCI
+ help
+ This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+ If unsure, say N.
+
+config SATA_FSL
+ tristate "Freescale 3.0Gbps SATA support"
+ depends on FSL_SOC
+ help
+ This option enables support for Freescale 3.0Gbps SATA controller.
+ It can be found on MPC837x and MPC8315.
+
+ If unsure, say N.
+
+config ATA_SFF
+ bool "ATA SFF support"
+ default y
+ help
+ This option adds support for ATA controllers with SFF
+ compliant or similar programming interface.
+
+ SFF is the legacy IDE interface that has been around since
+ the dawn of time. Almost all PATA controllers have an
+ SFF interface. Many SATA controllers have an SFF interface
+ when configured into a legacy compatibility mode.
+
+ For users with exclusively modern controllers like AHCI,
+ Silicon Image 3124, or Marvell 6440, you may choose to
+ disable this unneeded SFF support.
+
+ If unsure, say Y.
+
+if ATA_SFF
+
config SATA_SVW
tristate "ServerWorks Frodo / Apple K2 SATA support"
depends on PCI
If unsure, say N.
config ATA_PIIX
- tristate "Intel PIIX/ICH SATA support"
+ tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support"
depends on PCI
help
- This option enables support for ICH5/6/7/8 Serial ATA.
- If PATA support was enabled previously, this enables
- support for select Intel PIIX/ICH PATA host controllers.
+ This option enables support for ICH5/6/7/8 Serial ATA
+ and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series
+ host controllers.
If unsure, say N.
config SATA_MV
- tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Marvell SATA support"
help
This option enables support for the Marvell Serial ATA family.
- Currently supports 88SX[56]0[48][01] chips.
+ Currently supports 88SX[56]0[48][01] PCI(-X) chips,
+ as well as the newer [67]042 PCI-X/PCIe and SOC devices.
If unsure, say N.
If unsure, say N.
config SATA_SX4
- tristate "Promise SATA SX4 support"
+ tristate "Promise SATA SX4 support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for Promise Serial ATA SX4.
If unsure, say N.
-config SATA_SIL24
- tristate "Silicon Image 3124/3132 SATA support"
- depends on PCI
- help
- This option enables support for Silicon Image 3124/3132 Serial ATA.
-
- If unsure, say N.
-
config SATA_SIS
- tristate "SiS 964/180 SATA support"
+ tristate "SiS 964/965/966/180 SATA support"
depends on PCI
+ select PATA_SIS
help
- This option enables support for SiS Serial ATA 964/180.
-
+ This option enables support for SiS Serial ATA on
+ SiS 964/965/966/180 and Parallel ATA on SiS 180.
+ The PATA support for SiS 180 requires additionally to
+ enable the PATA_SIS driver in the config.
If unsure, say N.
config SATA_ULI
If unsure, say N.
-config SATA_INTEL_COMBINED
- bool
- depends on IDE=y && !BLK_DEV_IDE_SATA && (SATA_AHCI || ATA_PIIX)
- default y
+config SATA_INIC162X
+ tristate "Initio 162x SATA support"
+ depends on PCI
+ help
+ This option enables support for Initio 162x Serial ATA.
+
+config PATA_ACPI
+ tristate "ACPI firmware driver for PATA"
+ depends on ATA_ACPI
+ help
+ This option enables an ACPI method driver which drives
+ motherboard PATA controller interfaces through the ACPI
+ firmware in the BIOS. This driver can sometimes handle
+ otherwise unsupported hardware.
config PATA_ALI
- tristate "ALi PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ALi PATA support"
+ depends on PCI
help
This option enables support for the ALi ATA interfaces
found on the many ALi chipsets.
If unsure, say N.
config PATA_AMD
- tristate "AMD/NVidia PATA support (Experimental)"
+ tristate "AMD/NVidia PATA support"
depends on PCI
help
This option enables support for the AMD and NVidia PATA
If unsure, say N.
config PATA_ARTOP
- tristate "ARTOP 6210/6260 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ARTOP 6210/6260 PATA support"
+ depends on PCI
help
This option enables support for ARTOP PATA controllers.
If unsure, say N.
+config PATA_ATP867X
+ tristate "ARTOP/Acard ATP867X PATA support"
+ depends on PCI
+ help
+ This option enables support for ARTOP/Acard ATP867X PATA
+ controllers.
+
+ If unsure, say N.
+
+config PATA_AT32
+ tristate "Atmel AVR32 PATA support (Experimental)"
+ depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
+ help
+ This option enables support for the IDE devices on the
+ Atmel AT32AP platform.
+
+ If unsure, say N.
+
config PATA_ATIIXP
- tristate "ATI PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ATI PATA support"
+ depends on PCI
help
This option enables support for the ATI ATA interfaces
found on the many ATI chipsets.
If unsure, say N.
+config PATA_CMD640_PCI
+ tristate "CMD640 PCI PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the CMD640 PCI IDE
+ interface chip. Only the primary channel is currently
+ supported.
+
+ If unsure, say N.
+
config PATA_CMD64X
- tristate "CMD64x PATA support (Very Experimental)"
- depends on PCI&& EXPERIMENTAL
+ tristate "CMD64x PATA support"
+ depends on PCI
help
This option enables support for the CMD64x series chips
except for the CMD640.
If unsure, say N.
config PATA_CS5530
- tristate "CS5530 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "CS5530 PATA support"
+ depends on PCI
help
This option enables support for the Cyrix/NatSemi/AMD CS5530
companion chip used with the MediaGX/Geode processor family.
If unsure, say N.
+config PATA_CS5536
+ tristate "CS5536 PATA support"
+ depends on PCI && X86 && !X86_64
+ help
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
+
+ If unsure, say N.
+
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
config PATA_HPT366
- tristate "HPT 366/368 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 366/368 PATA support"
+ depends on PCI
help
This option enables support for the HPT 366 and 368
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT37X
- tristate "HPT 370/370A/371/372/374/302 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 370/370A/371/372/374/302 PATA support"
+ depends on PCI
help
This option enables support for the majority of the later HPT
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT3X2N
- tristate "HPT 372N/302N PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 372N/302N PATA support"
+ depends on PCI
help
This option enables support for the N variant HPT PATA
controllers via the new ATA layer
If unsure, say N.
config PATA_HPT3X3
- tristate "HPT 343/363 PATA support (Experimental)"
+ tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
If unsure, say N.
+config PATA_HPT3X3_DMA
+ bool "HPT 343/363 DMA support"
+ depends on PATA_HPT3X3
+ help
+ This option enables DMA support for the HPT343/363
+ controllers. Enable with care as there are still some
+ problems with DMA on this chipset.
+
config PATA_ISAPNP
- tristate "ISA Plug and Play PATA support (Very Experimental)"
- depends on EXPERIMENTAL && ISAPNP
+ tristate "ISA Plug and Play PATA support"
+ depends on ISAPNP
help
This option enables support for ISA plug & play ATA
controllers such as those found on old soundcards.
If unsure, say N.
config PATA_IT821X
- tristate "IT821x PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "IT8211/2 PATA support"
+ depends on PCI
help
This option enables support for the ITE 8211 and 8212
PATA controllers via the new ATA layer, including RAID
If unsure, say N.
+config PATA_IT8213
+ tristate "IT8213 PATA support (Experimental)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This option enables support for the ITE 821 PATA
+ controllers via the new ATA layer.
+
+ If unsure, say N.
+
config PATA_JMICRON
tristate "JMicron PATA support"
depends on PCI
config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ depends on (ISA || PCI) && EXPERIMENTAL
help
- This option enables support for ISA/VLB bus legacy PATA
+ This option enables support for ISA/VLB/PCI bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
If unsure, say N.
If unsure, say N.
+config PATA_MARVELL
+ tristate "Marvell PATA support via legacy mode"
+ depends on PCI
+ help
+ This option enables limited support for the Marvell 88SE61xx ATA
+ controllers. If you wish to use only the SATA ports then select
+ the AHCI driver alone. If you wish to the use the PATA port or
+ both SATA and PATA include this driver.
+
+ If unsure, say N.
+
+config PATA_MPC52xx
+ tristate "Freescale MPC52xx SoC internal IDE"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select PPC_BESTCOMM_ATA
+ help
+ This option enables support for integrated IDE controller
+ of the Freescale MPC52xx SoC.
+
+ If unsure, say N.
+
config PATA_MPIIX
tristate "Intel PATA MPIIX support"
depends on PCI
If unsure, say N.
config PATA_OLDPIIX
- tristate "Intel PATA old PIIX support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "Intel PATA old PIIX support"
+ depends on PCI
help
- This option enables support for old(?) PIIX PATA support.
+ This option enables support for early PIIX PATA support.
If unsure, say N.
If unsure, say N.
+config PATA_NINJA32
+ tristate "Ninja32/Delkin Cardbus ATA support"
+ depends on PCI
+ help
+ This option enables support for the Ninja32, Delkin and
+ possibly other brands of Cardbus ATA adapter
+
+ If unsure, say N.
+
config PATA_NS87410
- tristate "Nat Semi NS87410 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "Nat Semi NS87410 PATA support"
+ depends on PCI
help
This option enables support for the National Semiconductor
NS87410 PCI-IDE controller.
If unsure, say N.
+config PATA_NS87415
+ tristate "Nat Semi NS87415 PATA support"
+ depends on PCI
+ help
+ This option enables support for the National Semiconductor
+ NS87415 PCI-IDE controller.
+
+ If unsure, say N.
+
config PATA_OPTI
tristate "OPTI621/6215 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
config PATA_OPTIDMA
- tristate "OPTI FireStar PATA support (Veyr Experimental)"
+ tristate "OPTI FireStar PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables DMA/PIO support for the later OPTi
controllers found on some old motherboards and in some
- latops
+ laptops.
+
+ If unsure, say N.
+
+config PATA_PALMLD
+ tristate "Palm LifeDrive PATA support"
+ depends on MACH_PALMLD
+ help
+ This option enables support for Palm LifeDrive's internal ATA
+ port via the new ATA layer.
If unsure, say N.
If unsure, say N.
+config PATA_PDC2027X
+ tristate "Promise PATA 2027x support"
+ depends on PCI
+ help
+ This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+
+ If unsure, say N.
+
config PATA_PDC_OLD
- tristate "Older Promise PATA controller support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "Older Promise PATA controller support"
+ depends on PCI
help
This option enables support for the Promise 20246, 20262, 20263,
20265 and 20267 adapters.
config PATA_QDI
tristate "QDI VLB PATA support"
+ depends on ISA
help
Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
config PATA_RADISYS
- tristate "RADISYS 82600 PATA support (Very experimental)"
+ tristate "RADISYS 82600 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the RADISYS 82600
If unsure, say N.
+config PATA_RB532
+ tristate "RouterBoard 532 PATA CompactFlash support"
+ depends on MIKROTIK_RB532
+ help
+ This option enables support for the RouterBoard 532
+ PATA CompactFlash controller.
+
+ If unsure, say N.
+
+config PATA_RDC
+ tristate "RDC PATA support"
+ depends on PCI
+ help
+ This option enables basic support for the later RDC PATA controllers
+ controllers via the new ATA layer. For the RDC 1010, you need to
+ enable the IT821X driver instead.
+
+ If unsure, say N.
+
config PATA_RZ1000
tristate "PC Tech RZ1000 PATA support"
depends on PCI
If unsure, say N.
config PATA_SC1200
- tristate "SC1200 PATA support (Raving Lunatic)"
- depends on PCI && EXPERIMENTAL
+ tristate "SC1200 PATA support"
+ depends on PCI
help
This option enables support for the NatSemi/AMD SC1200 SoC
companion chip used with the Geode processor family.
If unsure, say N.
config PATA_SERVERWORKS
- tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support"
+ depends on PCI
help
This option enables support for the Serverworks OSB4/CSB5/CSB6 and
HT1000 PATA controllers, via the new ATA layer.
If unsure, say N.
-config PATA_PDC2027X
- tristate "Promise PATA 2027x support"
+config PATA_SIL680
+ tristate "CMD / Silicon Image 680 PATA support"
depends on PCI
help
- This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+ This option enables support for CMD / Silicon Image 680 PATA.
If unsure, say N.
-config PATA_SIL680
- tristate "CMD / Silicon Image 680 PATA support"
+config PATA_SIS
+ tristate "SiS PATA support"
depends on PCI
help
- This option enables support for CMD / Silicon Image 680 PATA.
+ This option enables support for SiS PATA controllers
If unsure, say N.
-config PATA_SIS
- tristate "SiS PATA support (Experimental)"
+config PATA_TOSHIBA
+ tristate "Toshiba Piccolo support (Experimental)"
depends on PCI && EXPERIMENTAL
help
- This option enables support for SiS PATA controllers
+ Support for the Toshiba Piccolo controllers. Currently only the
+ primary channel is supported by this driver.
If unsure, say N.
If unsure, say N.
-endif
-endmenu
+config PATA_WINBOND_VLB
+ tristate "Winbond W83759A VLB PATA support (Experimental)"
+ depends on ISA && EXPERIMENTAL
+ help
+ Support for the Winbond W83759A controller on Vesa Local Bus
+ systems.
+
+config HAVE_PATA_PLATFORM
+ bool
+ help
+ This is an internal configuration node for any machine that
+ uses pata-platform driver to enable the relevant driver in the
+ configuration structure without having to submit endless patches
+ to update the PATA_PLATFORM entry.
+
+config PATA_PLATFORM
+ tristate "Generic platform device PATA support"
+ depends on EMBEDDED || PPC || HAVE_PATA_PLATFORM
+ help
+ This option enables support for generic directly connected ATA
+ devices commonly found on embedded systems.
+
+ If unsure, say N.
+
+config PATA_AT91
+ tristate "PATA support for AT91SAM9260"
+ depends on ARM && ARCH_AT91
+ help
+ This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
+
+ If unsure, say N.
+
+config PATA_OF_PLATFORM
+ tristate "OpenFirmware platform device PATA support"
+ depends on PATA_PLATFORM && PPC_OF
+ help
+ This option enables support for generic directly connected ATA
+ devices commonly found on embedded systems with OpenFirmware
+ bindings.
+
+ If unsure, say N.
+
+config PATA_ICSIDE
+ tristate "Acorn ICS PATA support"
+ depends on ARM && ARCH_ACORN
+ help
+ On Acorn systems, say Y here if you wish to use the ICS PATA
+ interface card. This is not required for ICS partition support.
+ If you are unsure, say N to this.
+
+config PATA_IXP4XX_CF
+ tristate "IXP4XX Compact Flash support"
+ depends on ARCH_IXP4XX
+ help
+ This option enables support for a Compact Flash connected on
+ the ixp4xx expansion bus. This driver had been written for
+ Loft/Avila boards in mind but can work with others.
+
+ If unsure, say N.
+
+config PATA_OCTEON_CF
+ tristate "OCTEON Boot Bus Compact Flash support"
+ depends on CPU_CAVIUM_OCTEON
+ help
+ This option enables a polled compact flash driver for use with
+ compact flash cards attached to the OCTEON boot bus.
+
+ If unsure, say N.
+
+config PATA_SCC
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PCI && PPC_CELLEB
+ help
+ This option enables support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+
+ If unsure, say N.
+
+config PATA_SCH
+ tristate "Intel SCH PATA support"
+ depends on PCI
+ help
+ This option enables support for Intel SCH PATA on the Intel
+ SCH (US15W, US15L, UL11L) series host controllers.
+
+ If unsure, say N.
+
+config PATA_BF54X
+ tristate "Blackfin 54x ATAPI support"
+ depends on BF542 || BF548 || BF549
+ help
+ This option enables support for the built-in ATAPI controller on
+ Blackfin 54x family chips.
+
+ If unsure, say N.
+
+config PATA_MACIO
+ tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
+ depends on PPC_PMAC
+ help
+ Most IDE capable PowerMacs have IDE busses driven by a variant
+ of this controller which is part of the Apple chipset used on
+ most PowerMac models. Some models have multiple busses using
+ different chipsets, though generally, MacIO is one of them.
+
+endif # ATA_SFF
+endif # ATA