# SATA/PATA driver configuration
#
-menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
-
-config ATA
- tristate "ATA device support"
+menuconfig ATA
+ tristate "Serial ATA and Parallel ATA drivers"
+ depends on HAS_IOMEM
depends on BLOCK
depends on !(M32R || M68K) || BROKEN
- depends on !SUN4 || BROKEN
select SCSI
---help---
If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
that "speaks" the ATA protocol, also called ATA controller),
because you will be asked for it.
+ NOTE: ATA enables basic SCSI support; *however*,
+ 'SCSI disk support', 'SCSI tape support', or
+ 'SCSI CDROM support' may also be needed,
+ depending on your hardware configuration.
+
if ATA
config ATA_NONSTANDARD
bool
default n
+config ATA_VERBOSE_ERROR
+ bool "Verbose ATA error reporting"
+ default y
+ help
+ This option adds parsing of ATA command descriptions and error bits
+ in libata kernel output, making it easier to interpret.
+ This option will enlarge the kernel by approx. 6KB. Disable it only
+ if kernel size is more important than ease of debugging.
+
+ If unsure, say Y.
+
+config ATA_ACPI
+ bool "ATA ACPI Support"
+ depends on ACPI && PCI
+ default y
+ help
+ This option adds support for ATA-related ACPI objects.
+ These ACPI objects add the ability to retrieve taskfiles
+ from the ACPI BIOS and write them to the disk controller.
+ These objects may be related to performance, security,
+ power management, or other areas.
+ You can disable this at kernel boot time by using the
+ option libata.noacpi=1
+
+config SATA_PMP
+ bool "SATA Port Multiplier support"
+ default y
+ help
+ This option adds support for SATA Port Multipliers
+ (the SATA version of an ethernet hub, or SAS expander).
+
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
If unsure, say N.
+config SATA_SIL24
+ tristate "Silicon Image 3124/3132 SATA support"
+ depends on PCI
+ help
+ This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+ If unsure, say N.
+
+config SATA_FSL
+ tristate "Freescale 3.0Gbps SATA support"
+ depends on FSL_SOC
+ help
+ This option enables support for Freescale 3.0Gbps SATA controller.
+ It can be found on MPC837x and MPC8315.
+
+ If unsure, say N.
+
+config ATA_SFF
+ bool "ATA SFF support"
+ default y
+ help
+ This option adds support for ATA controllers with SFF
+ compliant or similar programming interface.
+
+ SFF is the legacy IDE interface that has been around since
+ the dawn of time. Almost all PATA controllers have an
+ SFF interface. Many SATA controllers have an SFF interface
+ when configured into a legacy compatibility mode.
+
+ For users with exclusively modern controllers like AHCI,
+ Silicon Image 3124, or Marvell 6440, you may choose to
+ disable this unneeded SFF support.
+
+ If unsure, say Y.
+
+if ATA_SFF
+
config SATA_SVW
tristate "ServerWorks Frodo / Apple K2 SATA support"
depends on PCI
If unsure, say N.
config SATA_MV
- tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Marvell SATA support"
help
This option enables support for the Marvell Serial ATA family.
- Currently supports 88SX[56]0[48][01] chips.
+ Currently supports 88SX[56]0[48][01] PCI(-X) chips,
+ as well as the newer [67]042 PCI-X/PCIe and SOC devices.
If unsure, say N.
If unsure, say N.
config SATA_SX4
- tristate "Promise SATA SX4 support"
+ tristate "Promise SATA SX4 support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for Promise Serial ATA SX4.
If unsure, say N.
-config SATA_SIL24
- tristate "Silicon Image 3124/3132 SATA support"
- depends on PCI
- help
- This option enables support for Silicon Image 3124/3132 Serial ATA.
-
- If unsure, say N.
-
config SATA_SIS
tristate "SiS 964/965/966/180 SATA support"
depends on PCI
select PATA_SIS
help
- This option enables support for SiS Serial ATA on
+ This option enables support for SiS Serial ATA on
SiS 964/965/966/180 and Parallel ATA on SiS 180.
The PATA support for SiS 180 requires additionally to
enable the PATA_SIS driver in the config.
If unsure, say N.
config SATA_INIC162X
- tristate "Initio 162x SATA support (HIGHLY EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Initio 162x SATA support"
+ depends on PCI
help
This option enables support for Initio 162x Serial ATA.
-config SATA_ACPI
- bool
- depends on ACPI && PCI
- default y
+config PATA_ACPI
+ tristate "ACPI firmware driver for PATA"
+ depends on ATA_ACPI
help
- This option adds support for SATA-related ACPI objects.
- These ACPI objects add the ability to retrieve taskfiles
- from the ACPI BIOS and write them to the disk controller.
- These objects may be related to performance, security,
- power management, or other areas.
- You can disable this at kernel boot time by using the
- option libata.noacpi=1
+ This option enables an ACPI method driver which drives
+ motherboard PATA controller interfaces through the ACPI
+ firmware in the BIOS. This driver can sometimes handle
+ otherwise unsupported hardware.
config PATA_ALI
- tristate "ALi PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ALi PATA support"
+ depends on PCI
help
This option enables support for the ALi ATA interfaces
found on the many ALi chipsets.
If unsure, say N.
config PATA_ARTOP
- tristate "ARTOP 6210/6260 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ARTOP 6210/6260 PATA support"
+ depends on PCI
help
This option enables support for ARTOP PATA controllers.
If unsure, say N.
+config PATA_ATP867X
+ tristate "ARTOP/Acard ATP867X PATA support"
+ depends on PCI
+ help
+ This option enables support for ARTOP/Acard ATP867X PATA
+ controllers.
+
+ If unsure, say N.
+
+config PATA_AT32
+ tristate "Atmel AVR32 PATA support (Experimental)"
+ depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
+ help
+ This option enables support for the IDE devices on the
+ Atmel AT32AP platform.
+
+ If unsure, say N.
+
config PATA_ATIIXP
- tristate "ATI PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "ATI PATA support"
+ depends on PCI
help
This option enables support for the ATI ATA interfaces
found on the many ATI chipsets.
If unsure, say N.
config PATA_CMD640_PCI
- tristate "CMD640 PCI PATA support (Very Experimental)"
+ tristate "CMD640 PCI PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the CMD640 PCI IDE
If unsure, say N.
config PATA_CMD64X
- tristate "CMD64x PATA support (Very Experimental)"
- depends on PCI&& EXPERIMENTAL
+ tristate "CMD64x PATA support"
+ depends on PCI
help
This option enables support for the CMD64x series chips
except for the CMD640.
If unsure, say N.
config PATA_CS5530
- tristate "CS5530 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "CS5530 PATA support"
+ depends on PCI
help
This option enables support for the Cyrix/NatSemi/AMD CS5530
companion chip used with the MediaGX/Geode processor family.
If unsure, say N.
+config PATA_CS5536
+ tristate "CS5536 PATA support"
+ depends on PCI && X86 && !X86_64
+ help
+ This option enables support for the AMD CS5536
+ companion chip used with the Geode LX processor family.
+
+ If unsure, say N.
+
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
If unsure, say N.
config PATA_HPT366
- tristate "HPT 366/368 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 366/368 PATA support"
+ depends on PCI
help
This option enables support for the HPT 366 and 368
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT37X
- tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 370/370A/371/372/374/302 PATA support"
+ depends on PCI
help
This option enables support for the majority of the later HPT
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT3X2N
- tristate "HPT 372N/302N PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "HPT 372N/302N PATA support"
+ depends on PCI
help
This option enables support for the N variant HPT PATA
controllers via the new ATA layer
If unsure, say N.
config PATA_HPT3X3
- tristate "HPT 343/363 PATA support (Experimental)"
+ tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
If unsure, say N.
+config PATA_HPT3X3_DMA
+ bool "HPT 343/363 DMA support"
+ depends on PATA_HPT3X3
+ help
+ This option enables DMA support for the HPT343/363
+ controllers. Enable with care as there are still some
+ problems with DMA on this chipset.
+
config PATA_ISAPNP
- tristate "ISA Plug and Play PATA support (Experimental)"
- depends on EXPERIMENTAL && ISAPNP
+ tristate "ISA Plug and Play PATA support"
+ depends on ISAPNP
help
This option enables support for ISA plug & play ATA
controllers such as those found on old soundcards.
config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
- depends on ISA && EXPERIMENTAL
+ depends on (ISA || PCI) && EXPERIMENTAL
help
- This option enables support for ISA/VLB bus legacy PATA
+ This option enables support for ISA/VLB/PCI bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
If unsure, say N.
tristate "Marvell PATA support via legacy mode"
depends on PCI
help
- This option enables limited support for the Marvell 88SE6145 ATA
- controller.
+ This option enables limited support for the Marvell 88SE61xx ATA
+ controllers. If you wish to use only the SATA ports then select
+ the AHCI driver alone. If you wish to the use the PATA port or
+ both SATA and PATA include this driver.
If unsure, say N.
config PATA_MPC52xx
tristate "Freescale MPC52xx SoC internal IDE"
- depends on PPC_MPC52xx
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select PPC_BESTCOMM_ATA
help
This option enables support for integrated IDE controller
of the Freescale MPC52xx SoC.
If unsure, say N.
+config PATA_NINJA32
+ tristate "Ninja32/Delkin Cardbus ATA support"
+ depends on PCI
+ help
+ This option enables support for the Ninja32, Delkin and
+ possibly other brands of Cardbus ATA adapter
+
+ If unsure, say N.
+
config PATA_NS87410
- tristate "Nat Semi NS87410 PATA support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "Nat Semi NS87410 PATA support"
+ depends on PCI
help
This option enables support for the National Semiconductor
NS87410 PCI-IDE controller.
If unsure, say N.
+config PATA_NS87415
+ tristate "Nat Semi NS87415 PATA support"
+ depends on PCI
+ help
+ This option enables support for the National Semiconductor
+ NS87415 PCI-IDE controller.
+
+ If unsure, say N.
+
config PATA_OPTI
tristate "OPTI621/6215 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables DMA/PIO support for the later OPTi
controllers found on some old motherboards and in some
- latops
+ laptops.
+
+ If unsure, say N.
+
+config PATA_PALMLD
+ tristate "Palm LifeDrive PATA support"
+ depends on MACH_PALMLD
+ help
+ This option enables support for Palm LifeDrive's internal ATA
+ port via the new ATA layer.
If unsure, say N.
If unsure, say N.
+config PATA_PDC2027X
+ tristate "Promise PATA 2027x support"
+ depends on PCI
+ help
+ This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+
+ If unsure, say N.
+
config PATA_PDC_OLD
- tristate "Older Promise PATA controller support (Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "Older Promise PATA controller support"
+ depends on PCI
help
This option enables support for the Promise 20246, 20262, 20263,
20265 and 20267 adapters.
Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
config PATA_RADISYS
- tristate "RADISYS 82600 PATA support (Very Experimental)"
+ tristate "RADISYS 82600 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the RADISYS 82600
If unsure, say N.
+config PATA_RB532
+ tristate "RouterBoard 532 PATA CompactFlash support"
+ depends on MIKROTIK_RB532
+ help
+ This option enables support for the RouterBoard 532
+ PATA CompactFlash controller.
+
+ If unsure, say N.
+
+config PATA_RDC
+ tristate "RDC PATA support"
+ depends on PCI
+ help
+ This option enables basic support for the later RDC PATA controllers
+ controllers via the new ATA layer. For the RDC 1010, you need to
+ enable the IT821X driver instead.
+
+ If unsure, say N.
+
config PATA_RZ1000
tristate "PC Tech RZ1000 PATA support"
depends on PCI
If unsure, say N.
config PATA_SC1200
- tristate "SC1200 PATA support (Very Experimental)"
- depends on PCI && EXPERIMENTAL
+ tristate "SC1200 PATA support"
+ depends on PCI
help
This option enables support for the NatSemi/AMD SC1200 SoC
companion chip used with the Geode processor family.
If unsure, say N.
-config PATA_PDC2027X
- tristate "Promise PATA 2027x support"
+config PATA_SIL680
+ tristate "CMD / Silicon Image 680 PATA support"
depends on PCI
help
- This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+ This option enables support for CMD / Silicon Image 680 PATA.
If unsure, say N.
-config PATA_SIL680
- tristate "CMD / Silicon Image 680 PATA support"
+config PATA_SIS
+ tristate "SiS PATA support"
depends on PCI
help
- This option enables support for CMD / Silicon Image 680 PATA.
+ This option enables support for SiS PATA controllers
If unsure, say N.
-config PATA_SIS
- tristate "SiS PATA support (Experimental)"
+config PATA_TOSHIBA
+ tristate "Toshiba Piccolo support (Experimental)"
depends on PCI && EXPERIMENTAL
help
- This option enables support for SiS PATA controllers
+ Support for the Toshiba Piccolo controllers. Currently only the
+ primary channel is supported by this driver.
If unsure, say N.
Support for the Winbond W83759A controller on Vesa Local Bus
systems.
+config HAVE_PATA_PLATFORM
+ bool
+ help
+ This is an internal configuration node for any machine that
+ uses pata-platform driver to enable the relevant driver in the
+ configuration structure without having to submit endless patches
+ to update the PATA_PLATFORM entry.
+
config PATA_PLATFORM
tristate "Generic platform device PATA support"
- depends on EMBEDDED
+ depends on EMBEDDED || PPC || HAVE_PATA_PLATFORM
help
This option enables support for generic directly connected ATA
devices commonly found on embedded systems.
If unsure, say N.
+config PATA_AT91
+ tristate "PATA support for AT91SAM9260"
+ depends on ARM && ARCH_AT91
+ help
+ This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
+
+ If unsure, say N.
+
+config PATA_OF_PLATFORM
+ tristate "OpenFirmware platform device PATA support"
+ depends on PATA_PLATFORM && PPC_OF
+ help
+ This option enables support for generic directly connected ATA
+ devices commonly found on embedded systems with OpenFirmware
+ bindings.
+
+ If unsure, say N.
+
+config PATA_ICSIDE
+ tristate "Acorn ICS PATA support"
+ depends on ARM && ARCH_ACORN
+ help
+ On Acorn systems, say Y here if you wish to use the ICS PATA
+ interface card. This is not required for ICS partition support.
+ If you are unsure, say N to this.
+
config PATA_IXP4XX_CF
tristate "IXP4XX Compact Flash support"
depends on ARCH_IXP4XX
If unsure, say N.
+config PATA_OCTEON_CF
+ tristate "OCTEON Boot Bus Compact Flash support"
+ depends on CPU_CAVIUM_OCTEON
+ help
+ This option enables a polled compact flash driver for use with
+ compact flash cards attached to the OCTEON boot bus.
+
+ If unsure, say N.
+
config PATA_SCC
tristate "Toshiba's Cell Reference Set IDE support"
depends on PCI && PPC_CELLEB
If unsure, say N.
-endif
-endmenu
+config PATA_SCH
+ tristate "Intel SCH PATA support"
+ depends on PCI
+ help
+ This option enables support for Intel SCH PATA on the Intel
+ SCH (US15W, US15L, UL11L) series host controllers.
+
+ If unsure, say N.
+
+config PATA_BF54X
+ tristate "Blackfin 54x ATAPI support"
+ depends on BF542 || BF548 || BF549
+ help
+ This option enables support for the built-in ATAPI controller on
+ Blackfin 54x family chips.
+
+ If unsure, say N.
+
+config PATA_MACIO
+ tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
+ depends on PPC_PMAC
+ help
+ Most IDE capable PowerMacs have IDE busses driven by a variant
+ of this controller which is part of the Apple chipset used on
+ most PowerMac models. Some models have multiple busses using
+ different chipsets, though generally, MacIO is one of them.
+
+endif # ATA_SFF
+endif # ATA