select HAVE_UNSTABLE_SCHED_CLOCK
select HAVE_IDE
select HAVE_OPROFILE
+ select HAVE_IOREMAP_PROT
select HAVE_KPROBES
+ select ARCH_WANT_OPTIONAL_GPIOLIB
select HAVE_KRETPROBES
+ select HAVE_DYNAMIC_FTRACE
+ select HAVE_FTRACE
select HAVE_KVM if ((X86_32 && !X86_VOYAGER && !X86_VISWS && !X86_NUMAQ) || X86_64)
select HAVE_ARCH_KGDB if !X86_VOYAGER
+ select HAVE_GENERIC_DMA_COHERENT if X86_32
+ select HAVE_EFFICIENT_UNALIGNED_ACCESS
config ARCH_DEFCONFIG
string
config X86_SMP
bool
depends on SMP && ((X86_32 && !X86_VOYAGER) || X86_64)
+ select USE_GENERIC_SMP_HELPERS
default y
config X86_32_SMP
endif
-config X86_RDC321X
- bool "RDC R-321x SoC"
- depends on X86_32
- select M486
- select X86_REBOOTFIXUPS
- select GENERIC_GPIO
- select LEDS_CLASS
- select LEDS_GPIO
- select NEW_LEDS
- help
- This option is needed for RDC R-321x system-on-chip, also known
- as R-8610-(G).
- If you don't have one of these chips, you should say N here.
-
config X86_VSMP
bool "Support for ScaleMP vSMP"
select PARAVIRT
A kernel compiled for the Visual Workstation will run on general
PCs as well. See <file:Documentation/sgi-visws.txt> for details.
+config X86_RDC321X
+ bool "RDC R-321x SoC"
+ depends on X86_32
+ select M486
+ select X86_REBOOTFIXUPS
+ help
+ This option is needed for RDC R-321x system-on-chip, also known
+ as R-8610-(G).
+ If you don't have one of these chips, you should say N here.
+
config SCHED_NO_NO_OMIT_FRAME_POINTER
def_bool y
prompt "Single-depth WCHAN output"
config MEMTEST
bool "Memtest"
- depends on X86_64
- default y
help
This option adds a kernel parameter 'memtest', which allows memtest
to be set.
memtest=1, mean do 1 test pattern;
...
memtest=4, mean do 4 test patterns.
- If you are unsure how to answer this question, answer Y.
+ If you are unsure how to answer this question, answer N.
config X86_SUMMIT_NUMA
def_bool y
local memory controller of the CPU and add some more
NUMA awareness to the kernel.
- For i386 this is currently highly experimental and should be only
+ For 32-bit this is currently highly experimental and should be only
used for kernel development. It might also cause boot failures.
- For x86_64 this is recommended on all multiprocessor Opteron systems.
+ For 64-bit this is recommended on all multiprocessor Opteron systems.
If the system is EM64T, you should say N unless your system is
EM64T NUMA.
See <file:Documentation/mtrr.txt> for more information.
config MTRR_SANITIZER
- def_bool y
+ bool
prompt "MTRR cleanup support"
depends on MTRR
help
- Convert MTRR layout from continuous to discrete, so some X driver
- could add WB entries.
+ Convert MTRR layout from continuous to discrete, so X drivers can
+ add writeback entries.
- Say N here if you see bootup problems (boot crash, boot hang,
- spontaneous reboots).
-
- Could be disabled with disable_mtrr_cleanup. Also mtrr_chunk_size
- could be used to send largest mtrr entry size for continuous block
- to hold holes (aka. UC entries)
+ Can be disabled with disable_mtrr_cleanup on the kernel command line.
+ The largest mtrr entry size for a continous block can be set with
+ mtrr_chunk_size.
- If unsure, say Y.
+ If unsure, say N.
config MTRR_SANITIZER_ENABLE_DEFAULT
int "MTRR cleanup enable value (0-1)"
depends on MTRR_SANITIZER
help
mtrr cleanup spare entries default, it can be changed via
- mtrr_spare_reg_nr=
+ mtrr_spare_reg_nr=N on the kernel command line.
config X86_PAT
bool
strongly in flux, so no good recommendation can be made.
config CRASH_DUMP
- bool "kernel crash dumps (EXPERIMENTAL)"
+ bool "kernel crash dumps"
depends on X86_64 || (X86_32 && HIGHMEM)
help
Generate crash dump after being started by kexec.
(CONFIG_RELOCATABLE=y).
For more details see Documentation/kdump/kdump.txt
+config KEXEC_JUMP
+ bool "kexec jump (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ depends on KEXEC && HIBERNATION && X86_32
+ help
+ Jump between original kernel and kexeced kernel and invoke
+ code in physical address mode via KEXEC
+
config PHYSICAL_START
hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP)
default "0x1000000" if X86_NUMAQ