sh: Kill off the remnants of the old timer code.

[safe/jmp/linux-2.6] / arch / sh / Kconfig

diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 02688d7..fb75c2d 100644 (file)
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -15,6 +15,7 @@ config SUPERH
        select HAVE_IOREMAP_PROT if MMU
        select HAVE_ARCH_TRACEHOOK
        select HAVE_DMA_API_DEBUG
+       select RTC_LIB
        help
          The SuperH is a RISC processor targeted for use in embedded systems
          and consumer electronics; it was also used in the Sega Dreamcast
@@ -30,7 +31,6 @@ config SUPERH32
        select HAVE_DYNAMIC_FTRACE
        select HAVE_ARCH_KGDB
        select ARCH_HIBERNATION_POSSIBLE if MMU
-       select RTC_LIB
 
 config SUPERH64
        def_bool ARCH = "sh64"
@@ -83,6 +83,10 @@ config GENERIC_CLOCKEVENTS
 config GENERIC_CLOCKEVENTS_BROADCAST
        bool
 
+config GENERIC_CMOS_UPDATE
+       def_bool y
+       depends on SH_SH03 || SH_DREAMCAST
+
 config GENERIC_LOCKBREAK
        def_bool y
        depends on SMP && PREEMPT
@@ -141,10 +145,6 @@ config ARCH_NO_VIRT_TO_BUS
 config ARCH_HAS_DEFAULT_IDLE
        def_bool y
 
-config ARCH_USES_GETTIMEOFFSET
-       def_bool y 
-       depends on SUPERH64
-
 config IO_TRAPPED
        bool
 
@@ -168,6 +168,7 @@ config CPU_SH3
        bool
        select CPU_HAS_INTEVT
        select CPU_HAS_SR_RB
+       select SYS_SUPPORTS_TMU
 
 config CPU_SH4
        bool
@@ -175,6 +176,7 @@ config CPU_SH4
        select CPU_HAS_SR_RB
        select CPU_HAS_PTEA if !CPU_SH4A || CPU_SHX2
        select CPU_HAS_FPU if !CPU_SH4AL_DSP
+       select SYS_SUPPORTS_TMU
 
 config CPU_SH4A
        bool
@@ -188,6 +190,7 @@ config CPU_SH4AL_DSP
 config CPU_SH5
        bool
        select CPU_HAS_FPU
+       select SYS_SUPPORTS_TMU
 
 config CPU_SHX2
        bool
@@ -299,6 +302,7 @@ config CPU_SUBTYPE_SH7720
        bool "Support SH7720 processor"
        select CPU_SH3
        select CPU_HAS_DSP
+       select SYS_SUPPORTS_CMT
        help
          Select SH7720 if you have a SH3-DSP SH7720 CPU.
 
@@ -306,6 +310,7 @@ config CPU_SUBTYPE_SH7721
        bool "Support SH7721 processor"
        select CPU_SH3
        select CPU_HAS_DSP
+       select SYS_SUPPORTS_CMT
        help
          Select SH7721 if you have a SH3-DSP SH7721 CPU.
 
@@ -427,7 +432,6 @@ config CPU_SUBTYPE_SH7722
        select ARCH_SPARSEMEM_ENABLE
        select SYS_SUPPORTS_NUMA
        select SYS_SUPPORTS_CMT
-       select SYS_SUPPORTS_TMU
 
 config CPU_SUBTYPE_SH7366
        bool "Support SH7366 processor"
@@ -469,16 +473,9 @@ source "arch/sh/boards/Kconfig"
 
 menu "Timer and clock configuration"
 
-config SH_TMU
-       bool "TMU timer support"
-       depends on CPU_SH3 || CPU_SH4
-       default y
-       help
-         This enables the use of the TMU as the system timer.
-
 config SH_TIMER_TMU
        bool "TMU timer driver"
-       depends on !SH_TMU && SYS_SUPPORTS_TMU
+       depends on SYS_SUPPORTS_TMU
        default y
        help
          This enables the build of the TMU timer driver.
@@ -497,17 +494,6 @@ config SH_TIMER_MTU2
        help
          This enables build of the MTU2 timer driver.
 
-config SH_TIMER_IRQ
-       int
-       default "28" if CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785 || \
-                       CPU_SUBTYPE_SH7763
-       default "86" if CPU_SUBTYPE_SH7619
-       default "140" if CPU_SUBTYPE_SH7206
-       default "142" if CPU_SUBTYPE_SH7203 && SH_CMT
-       default "153" if CPU_SUBTYPE_SH7203 && SH_MTU2
-       default "238" if CPU_SUBTYPE_MXG
-       default "16"
-
 config SH_PCLK_FREQ
        int "Peripheral clock frequency (in Hz)"
        default "27000000" if CPU_SUBTYPE_SH7343
@@ -692,22 +678,37 @@ endmenu
 menu "Boot options"
 
 config ZERO_PAGE_OFFSET
-       hex "Zero page offset"
-       default "0x00004000" if SH_SH03
-       default "0x00010000" if PAGE_SIZE_64KB
+       hex
+       default "0x00010000" if PAGE_SIZE_64KB || SH_RTS7751R2D || \
+                               SH_7751_SOLUTION_ENGINE
+       default "0x00004000" if PAGE_SIZE_16KB || SH_SH03
        default "0x00002000" if PAGE_SIZE_8KB
        default "0x00001000"
        help
          This sets the default offset of zero page.
 
 config BOOT_LINK_OFFSET
-       hex "Link address offset for booting"
+       hex
+       default "0x00210000" if SH_SHMIN
+       default "0x00400000" if SH_CAYMAN
+       default "0x00810000" if SH_7780_SOLUTION_ENGINE
+       default "0x009e0000" if SH_TITAN
+       default "0x01800000" if SH_SDK7780
+       default "0x02000000" if SH_EDOSK7760
        default "0x00800000"
        help
          This option allows you to set the link address offset of the zImage.
          This can be useful if you are on a board which has a small amount of
          memory.
 
+config ENTRY_OFFSET
+       hex
+       default "0x00001000" if PAGE_SIZE_4KB
+       default "0x00002000" if PAGE_SIZE_8KB
+       default "0x00004000" if PAGE_SIZE_16KB
+       default "0x00010000" if PAGE_SIZE_64KB
+       default "0x00000000"
+
 config UBC_WAKEUP
        bool "Wakeup UBC on startup"
        depends on CPU_SH4 && !CPU_SH4A