select HAVE_IOREMAP_PROT if MMU
select HAVE_ARCH_TRACEHOOK
select HAVE_DMA_API_DEBUG
+ select HAVE_PERF_COUNTERS
select RTC_LIB
+ select GENERIC_ATOMIC64
help
The SuperH is a RISC processor targeted for use in embedded systems
and consumer electronics; it was also used in the Sega Dreamcast
def_bool y
depends on BUG && SUPERH32
+config GENERIC_CSUM
+ def_bool y
+ depends on SUPERH64
+
config GENERIC_FIND_NEXT_BIT
def_bool y
config GENERIC_IRQ_PROBE
def_bool y
+config IRQ_PER_CPU
+ def_bool y
+
config GENERIC_GPIO
def_bool n
config ARCH_HAS_DEFAULT_IDLE
def_bool y
+config ARCH_HAS_CPU_IDLE_WAIT
+ def_bool y
+
config IO_TRAPPED
bool
bool
select CPU_HAS_INTEVT
select CPU_HAS_SR_RB
- select CPU_HAS_PTEA if !CPU_SH4A || CPU_SHX2
select CPU_HAS_FPU if !CPU_SH4AL_DSP
select SYS_SUPPORTS_TMU
bool "Support SH7720 processor"
select CPU_SH3
select CPU_HAS_DSP
+ select SYS_SUPPORTS_CMT
help
Select SH7720 if you have a SH3-DSP SH7720 CPU.
bool "Support SH7721 processor"
select CPU_SH3
select CPU_HAS_DSP
+ select SYS_SUPPORTS_CMT
help
Select SH7721 if you have a SH3-DSP SH7721 CPU.
select CPU_HAS_PTEAEX
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_NUMA
+ select SYS_SUPPORTS_SMP
+ select GENERIC_CLOCKEVENTS_BROADCAST if SMP
config CPU_SUBTYPE_SHX3
bool "Support SH-X3 processor"
menu "Timer and clock configuration"
-config SH_TMU
- bool "TMU timer support"
- depends on CPU_SH3 || CPU_SH4
- default y
- help
- This enables the use of the TMU as the system timer.
-
config SH_TIMER_TMU
bool "TMU timer driver"
- depends on !SH_TMU && SYS_SUPPORTS_TMU
+ depends on SYS_SUPPORTS_TMU
default y
help
This enables the build of the TMU timer driver.
help
This enables build of the MTU2 timer driver.
-config SH_TIMER_IRQ
- int
- default "28" if CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785 || \
- CPU_SUBTYPE_SH7763
- default "86" if CPU_SUBTYPE_SH7619
- default "140" if CPU_SUBTYPE_SH7206
- default "142" if CPU_SUBTYPE_SH7203 && SH_CMT
- default "153" if CPU_SUBTYPE_SH7203 && SH_MTU2
- default "238" if CPU_SUBTYPE_MXG
- default "16"
-
config SH_PCLK_FREQ
int "Peripheral clock frequency (in Hz)"
default "27000000" if CPU_SUBTYPE_SH7343
CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7705 || \
CPU_SUBTYPE_SH7203 || CPU_SUBTYPE_SH7206 || \
CPU_SUBTYPE_SH7263 || CPU_SUBTYPE_MXG || \
- CPU_SUBTYPE_SH7786
- default "41666666" if CPU_SUBTYPE_SH7724
+ CPU_SUBTYPE_SH7786 || CPU_SUBTYPE_SH7724
default "60000000" if CPU_SUBTYPE_SH7751 || CPU_SUBTYPE_SH7751R
default "66000000" if CPU_SUBTYPE_SH4_202
default "50000000"
This is necessary for determining the reference clock value on
platforms lacking an RTC.
+config SH_CLK_CPG
+ def_bool y
+
+config SH_CLK_CPG_LEGACY
+ depends on SH_CLK_CPG
+ def_bool y if !CPU_SUBTYPE_SH7785 && !ARCH_SHMOBILE
+
config SH_CLK_MD
int "CPU Mode Pin Setting"
depends on CPU_SH2
int "Maximum number of CPUs (2-32)"
range 2 32
depends on SMP
- default "4" if CPU_SHX3
+ default "4" if CPU_SUBTYPE_SHX3
default "2"
help
This allows you to specify the maximum number of CPUs which this
LLSC, this should be more efficient than the other alternative of
disabling interrupts around the atomic sequence.
+config SPARSE_IRQ
+ bool "Support sparse irq numbering"
+ depends on EXPERIMENTAL
+ help
+ This enables support for sparse irqs. This is useful in general
+ as most CPUs have a fairly sparse array of IRQ vectors, which
+ the irq_desc then maps directly on to. Systems with a high
+ number of off-chip IRQs will want to treat this as
+ experimental until they have been independently verified.
+
+ If you don't know what to do here, say N.
+
endmenu
menu "Boot options"
config ZERO_PAGE_OFFSET
- hex "Zero page offset"
- default "0x00004000" if SH_SH03
- default "0x00010000" if PAGE_SIZE_64KB
+ hex
+ default "0x00010000" if PAGE_SIZE_64KB || SH_RTS7751R2D || \
+ SH_7751_SOLUTION_ENGINE
+ default "0x00004000" if PAGE_SIZE_16KB || SH_SH03
default "0x00002000" if PAGE_SIZE_8KB
default "0x00001000"
help
This sets the default offset of zero page.
config BOOT_LINK_OFFSET
- hex "Link address offset for booting"
+ hex
+ default "0x00210000" if SH_SHMIN
+ default "0x00400000" if SH_CAYMAN
+ default "0x00810000" if SH_7780_SOLUTION_ENGINE
+ default "0x009e0000" if SH_TITAN
+ default "0x01800000" if SH_SDK7780
+ default "0x02000000" if SH_EDOSK7760
default "0x00800000"
help
This option allows you to set the link address offset of the zImage.
This can be useful if you are on a board which has a small amount of
memory.
+config ENTRY_OFFSET
+ hex
+ default "0x00001000" if PAGE_SIZE_4KB
+ default "0x00002000" if PAGE_SIZE_8KB
+ default "0x00004000" if PAGE_SIZE_16KB
+ default "0x00010000" if PAGE_SIZE_64KB
+ default "0x00000000"
+
config UBC_WAKEUP
bool "Wakeup UBC on startup"
depends on CPU_SH4 && !CPU_SH4A