* 2 of the License, or (at your option) any later version.
*/
-#include <linux/config.h>
#include <linux/threads.h>
#include <asm/reg.h>
#include <asm/page.h>
#include <asm/hvcall.h>
#include <asm/iseries/lpar_map.h>
#include <asm/thread_info.h>
-
-#ifdef CONFIG_PPC_ISERIES
-#define DO_SOFT_DISABLE
-#endif
+#include <asm/firmware.h>
+#include <asm/page_64.h>
+#include <asm/exception.h>
+#include <asm/irqflags.h>
/*
* We layout physical memory as follows:
.text
.globl _stext
_stext:
-#ifdef CONFIG_PPC_MULTIPLATFORM
_GLOBAL(__start)
/* NOP this out unconditionally */
BEGIN_FTR_SECTION
b .__start_initialization_multiplatform
END_FTR_SECTION(0, 1)
-#endif /* CONFIG_PPC_MULTIPLATFORM */
/* Catch branch to 0 in real mode */
trap
- /* Secondary processors spin on this value until it goes to 1. */
+ /* Secondary processors spin on this value until it becomes nonzero.
+ * When it does it contains the real address of the descriptor
+ * of the function that the cpu should jump to to continue
+ * initialization.
+ */
.globl __secondary_hold_spinloop
__secondary_hold_spinloop:
.llong 0x0
.llong hvReleaseData-KERNELBASE
#endif /* CONFIG_PPC_ISERIES */
+#ifdef CONFIG_CRASH_DUMP
+ /* This flag is set to 1 by a loader if the kernel should run
+ * at the loaded address instead of the linked address. This
+ * is used by kexec-tools to keep the the kdump kernel in the
+ * crash_kernel region. The loader is responsible for
+ * observing the alignment requirement.
+ */
+ /* Do not move this variable as kexec-tools knows about it. */
+ . = 0x5c
+ .globl __run_at_load
+__run_at_load:
+ .long 0x72756e30 /* "run0" -- relocate to 0 by default */
+#endif
+
. = 0x60
/*
- * The following code is used on pSeries to hold secondary processors
- * in a spin loop after they have been freed from OpenFirmware, but
+ * The following code is used to hold secondary processors
+ * in a spin loop after they have entered the kernel, but
* before the bulk of the kernel has been relocated. This code
* is relocated to physical address 0x60 before prom_init is run.
* All of it must fit below the first exception vector at 0x100.
+ * Use .globl here not _GLOBAL because we want __secondary_hold
+ * to be the actual text address, not a descriptor.
*/
-_GLOBAL(__secondary_hold)
+ .globl __secondary_hold
+__secondary_hold:
mfmsr r24
ori r24,r24,MSR_RI
mtmsrd r24 /* RI on */
/* Tell the master cpu we're here */
/* Relocation is off & we are located at an address less */
/* than 0x100, so only need to grab low order offset. */
- std r24,__secondary_hold_acknowledge@l(0)
+ std r24,__secondary_hold_acknowledge-_stext(0)
sync
/* All secondary cpus wait here until told to start. */
-100: ld r4,__secondary_hold_spinloop@l(0)
- cmpdi 0,r4,1
- bne 100b
+100: ld r4,__secondary_hold_spinloop-_stext(0)
+ cmpdi 0,r4,0
+ beq 100b
#if defined(CONFIG_SMP) || defined(CONFIG_KEXEC)
- LOAD_REG_IMMEDIATE(r4, .pSeries_secondary_smp_init)
+ ld r4,0(r4) /* deref function descriptor */
mtctr r4
mr r3,r24
bctr
.text
/*
- * The following macros define the code that appears as
- * the prologue to each of the exception handlers. They
- * are split into two parts to allow a single kernel binary
- * to be used for pSeries and iSeries.
- * LOL. One day... - paulus
- */
-
-/*
- * We make as much of the exception code common between native
- * exception handlers (including pSeries LPAR) and iSeries LPAR
- * implementations as possible.
- */
-
-/*
* This is the start of the interrupt handlers for pSeries
* This code runs with relocation off.
- */
-#define EX_R9 0
-#define EX_R10 8
-#define EX_R11 16
-#define EX_R12 24
-#define EX_R13 32
-#define EX_SRR0 40
-#define EX_DAR 48
-#define EX_DSISR 56
-#define EX_CCR 60
-#define EX_R3 64
-#define EX_LR 72
-
-/*
- * We're short on space and time in the exception prolog, so we can't
- * use the normal SET_REG_IMMEDIATE macro. Normally we just need the
- * low halfword of the address, but for Kdump we need the whole low
- * word.
- */
-#ifdef CONFIG_CRASH_DUMP
-#define LOAD_HANDLER(reg, label) \
- oris reg,reg,(label)@h; /* virt addr of handler ... */ \
- ori reg,reg,(label)@l; /* .. and the rest */
-#else
-#define LOAD_HANDLER(reg, label) \
- ori reg,reg,(label)@l; /* virt addr of handler ... */
-#endif
-
-#define EXCEPTION_PROLOG_PSERIES(area, label) \
- mfspr r13,SPRN_SPRG3; /* get paca address into r13 */ \
- std r9,area+EX_R9(r13); /* save r9 - r12 */ \
- std r10,area+EX_R10(r13); \
- std r11,area+EX_R11(r13); \
- std r12,area+EX_R12(r13); \
- mfspr r9,SPRN_SPRG1; \
- std r9,area+EX_R13(r13); \
- mfcr r9; \
- clrrdi r12,r13,32; /* get high part of &label */ \
- mfmsr r10; \
- mfspr r11,SPRN_SRR0; /* save SRR0 */ \
- LOAD_HANDLER(r12,label) \
- ori r10,r10,MSR_IR|MSR_DR|MSR_RI; \
- mtspr SPRN_SRR0,r12; \
- mfspr r12,SPRN_SRR1; /* and SRR1 */ \
- mtspr SPRN_SRR1,r10; \
- rfid; \
- b . /* prevent speculative execution */
-
-/*
- * This is the start of the interrupt handlers for iSeries
- * This code runs with relocation on.
- */
-#define EXCEPTION_PROLOG_ISERIES_1(area) \
- mfspr r13,SPRN_SPRG3; /* get paca address into r13 */ \
- std r9,area+EX_R9(r13); /* save r9 - r12 */ \
- std r10,area+EX_R10(r13); \
- std r11,area+EX_R11(r13); \
- std r12,area+EX_R12(r13); \
- mfspr r9,SPRN_SPRG1; \
- std r9,area+EX_R13(r13); \
- mfcr r9
-
-#define EXCEPTION_PROLOG_ISERIES_2 \
- mfmsr r10; \
- ld r12,PACALPPACAPTR(r13); \
- ld r11,LPPACASRR0(r12); \
- ld r12,LPPACASRR1(r12); \
- ori r10,r10,MSR_RI; \
- mtmsrd r10,1
-
-/*
- * The common exception prolog is used for all except a few exceptions
- * such as a segment miss on a kernel address. We have to be prepared
- * to take another exception from the point where we first touch the
- * kernel stack onwards.
- *
- * On entry r13 points to the paca, r9-r13 are saved in the paca,
- * r9 contains the saved CR, r11 and r12 contain the saved SRR0 and
- * SRR1, and relocation is on.
- */
-#define EXCEPTION_PROLOG_COMMON(n, area) \
- andi. r10,r12,MSR_PR; /* See if coming from user */ \
- mr r10,r1; /* Save r1 */ \
- subi r1,r1,INT_FRAME_SIZE; /* alloc frame on kernel stack */ \
- beq- 1f; \
- ld r1,PACAKSAVE(r13); /* kernel stack to use */ \
-1: cmpdi cr1,r1,0; /* check if r1 is in userspace */ \
- bge- cr1,bad_stack; /* abort if it is */ \
- std r9,_CCR(r1); /* save CR in stackframe */ \
- std r11,_NIP(r1); /* save SRR0 in stackframe */ \
- std r12,_MSR(r1); /* save SRR1 in stackframe */ \
- std r10,0(r1); /* make stack chain pointer */ \
- std r0,GPR0(r1); /* save r0 in stackframe */ \
- std r10,GPR1(r1); /* save r1 in stackframe */ \
- ACCOUNT_CPU_USER_ENTRY(r9, r10); \
- std r2,GPR2(r1); /* save r2 in stackframe */ \
- SAVE_4GPRS(3, r1); /* save r3 - r6 in stackframe */ \
- SAVE_2GPRS(7, r1); /* save r7, r8 in stackframe */ \
- ld r9,area+EX_R9(r13); /* move r9, r10 to stackframe */ \
- ld r10,area+EX_R10(r13); \
- std r9,GPR9(r1); \
- std r10,GPR10(r1); \
- ld r9,area+EX_R11(r13); /* move r11 - r13 to stackframe */ \
- ld r10,area+EX_R12(r13); \
- ld r11,area+EX_R13(r13); \
- std r9,GPR11(r1); \
- std r10,GPR12(r1); \
- std r11,GPR13(r1); \
- ld r2,PACATOC(r13); /* get kernel TOC into r2 */ \
- mflr r9; /* save LR in stackframe */ \
- std r9,_LINK(r1); \
- mfctr r10; /* save CTR in stackframe */ \
- std r10,_CTR(r1); \
- mfspr r11,SPRN_XER; /* save XER in stackframe */ \
- std r11,_XER(r1); \
- li r9,(n)+1; \
- std r9,_TRAP(r1); /* set trap number */ \
- li r10,0; \
- ld r11,exception_marker@toc(r2); \
- std r10,RESULT(r1); /* clear regs->result */ \
- std r11,STACK_FRAME_OVERHEAD-16(r1); /* mark the frame */
-
-/*
- * Exception vectors.
- */
-#define STD_EXCEPTION_PSERIES(n, label) \
- . = n; \
- .globl label##_pSeries; \
-label##_pSeries: \
- HMT_MEDIUM; \
- mtspr SPRN_SPRG1,r13; /* save r13 */ \
- EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, label##_common)
-
-#define HSTD_EXCEPTION_PSERIES(n, label) \
- . = n; \
- .globl label##_pSeries; \
-label##_pSeries: \
- HMT_MEDIUM; \
- mtspr SPRN_SPRG1,r20; /* save r20 */ \
- mfspr r20,SPRN_HSRR0; /* copy HSRR0 to SRR0 */ \
- mtspr SPRN_SRR0,r20; \
- mfspr r20,SPRN_HSRR1; /* copy HSRR0 to SRR0 */ \
- mtspr SPRN_SRR1,r20; \
- mfspr r20,SPRN_SPRG1; /* restore r20 */ \
- mtspr SPRN_SPRG1,r13; /* save r13 */ \
- EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, label##_common)
-
-
-#define STD_EXCEPTION_ISERIES(n, label, area) \
- .globl label##_iSeries; \
-label##_iSeries: \
- HMT_MEDIUM; \
- mtspr SPRN_SPRG1,r13; /* save r13 */ \
- EXCEPTION_PROLOG_ISERIES_1(area); \
- EXCEPTION_PROLOG_ISERIES_2; \
- b label##_common
-
-#define MASKABLE_EXCEPTION_ISERIES(n, label) \
- .globl label##_iSeries; \
-label##_iSeries: \
- HMT_MEDIUM; \
- mtspr SPRN_SPRG1,r13; /* save r13 */ \
- EXCEPTION_PROLOG_ISERIES_1(PACA_EXGEN); \
- lbz r10,PACAPROCENABLED(r13); \
- cmpwi 0,r10,0; \
- beq- label##_iSeries_masked; \
- EXCEPTION_PROLOG_ISERIES_2; \
- b label##_common; \
-
-#ifdef DO_SOFT_DISABLE
-#define DISABLE_INTS \
- lbz r10,PACAPROCENABLED(r13); \
- li r11,0; \
- std r10,SOFTE(r1); \
- mfmsr r10; \
- stb r11,PACAPROCENABLED(r13); \
- ori r10,r10,MSR_EE; \
- mtmsrd r10,1
-
-#define ENABLE_INTS \
- lbz r10,PACAPROCENABLED(r13); \
- mfmsr r11; \
- std r10,SOFTE(r1); \
- ori r11,r11,MSR_EE; \
- mtmsrd r11,1
-
-#else /* hard enable/disable interrupts */
-#define DISABLE_INTS
-
-#define ENABLE_INTS \
- ld r12,_MSR(r1); \
- mfmsr r11; \
- rlwimi r11,r12,0,MSR_EE; \
- mtmsrd r11,1
-
-#endif
-
-#define STD_EXCEPTION_COMMON(trap, label, hdlr) \
- .align 7; \
- .globl label##_common; \
-label##_common: \
- EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \
- DISABLE_INTS; \
- bl .save_nvgprs; \
- addi r3,r1,STACK_FRAME_OVERHEAD; \
- bl hdlr; \
- b .ret_from_except
-
-/*
- * Like STD_EXCEPTION_COMMON, but for exceptions that can occur
- * in the idle task and therefore need the special idle handling.
- */
-#define STD_EXCEPTION_COMMON_IDLE(trap, label, hdlr) \
- .align 7; \
- .globl label##_common; \
-label##_common: \
- EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \
- FINISH_NAP; \
- DISABLE_INTS; \
- bl .save_nvgprs; \
- addi r3,r1,STACK_FRAME_OVERHEAD; \
- bl hdlr; \
- b .ret_from_except
-
-#define STD_EXCEPTION_COMMON_LITE(trap, label, hdlr) \
- .align 7; \
- .globl label##_common; \
-label##_common: \
- EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \
- FINISH_NAP; \
- DISABLE_INTS; \
- bl .ppc64_runlatch_on; \
- addi r3,r1,STACK_FRAME_OVERHEAD; \
- bl hdlr; \
- b .ret_from_except_lite
-
-/*
- * When the idle code in power4_idle puts the CPU into NAP mode,
- * it has to do so in a loop, and relies on the external interrupt
- * and decrementer interrupt entry code to get it out of the loop.
- * It sets the _TLF_NAPPING bit in current_thread_info()->local_flags
- * to signal that it is in the loop and needs help to get out.
- */
-#ifdef CONFIG_PPC_970_NAP
-#define FINISH_NAP \
-BEGIN_FTR_SECTION \
- clrrdi r11,r1,THREAD_SHIFT; \
- ld r9,TI_LOCAL_FLAGS(r11); \
- andi. r10,r9,_TLF_NAPPING; \
- bnel power4_fixup_nap; \
-END_FTR_SECTION_IFSET(CPU_FTR_CAN_NAP)
-#else
-#define FINISH_NAP
-#endif
-
-/*
- * Start of pSeries system interrupt routines
+ * Code from here to __end_interrupts gets copied down to real
+ * address 0x100 when we are running a relocatable kernel.
+ * Therefore any relative branches in this section must only
+ * branch to labels in this section.
*/
. = 0x100
.globl __start_interrupts
rlwimi r13,r12,16,0x20
mfcr r12
cmpwi r13,0x2c
- beq .do_stab_bolted_pSeries
+ beq do_stab_bolted_pSeries
mtcrf 0x80,r12
mfspr r12,SPRN_SPRG2
END_FTR_SECTION_IFCLR(CPU_FTR_SLB)
mfspr r10,SPRN_SPRG1
std r10,PACA_EXSLB+EX_R13(r13)
mfspr r12,SPRN_SRR1 /* and SRR1 */
- b .slb_miss_realmode /* Rel. branch works in real mode */
+#ifndef CONFIG_RELOCATABLE
+ b .slb_miss_realmode
+#else
+ /*
+ * We can't just use a direct branch to .slb_miss_realmode
+ * because the distance from here to there depends on where
+ * the kernel ends up being put.
+ */
+ mfctr r11
+ ld r10,PACAKBASE(r13)
+ LOAD_HANDLER(r10, .slb_miss_realmode)
+ mtctr r10
+ bctr
+#endif
STD_EXCEPTION_PSERIES(0x400, instruction_access)
mfspr r10,SPRN_SPRG1
std r10,PACA_EXSLB+EX_R13(r13)
mfspr r12,SPRN_SRR1 /* and SRR1 */
- b .slb_miss_realmode /* Rel. branch works in real mode */
+#ifndef CONFIG_RELOCATABLE
+ b .slb_miss_realmode
+#else
+ mfctr r11
+ ld r10,PACAKBASE(r13)
+ LOAD_HANDLER(r10, .slb_miss_realmode)
+ mtctr r10
+ bctr
+#endif
- STD_EXCEPTION_PSERIES(0x500, hardware_interrupt)
+ MASKABLE_EXCEPTION_PSERIES(0x500, hardware_interrupt)
STD_EXCEPTION_PSERIES(0x600, alignment)
STD_EXCEPTION_PSERIES(0x700, program_check)
STD_EXCEPTION_PSERIES(0x800, fp_unavailable)
- STD_EXCEPTION_PSERIES(0x900, decrementer)
+ MASKABLE_EXCEPTION_PSERIES(0x900, decrementer)
STD_EXCEPTION_PSERIES(0xa00, trap_0a)
STD_EXCEPTION_PSERIES(0xb00, trap_0b)
.globl system_call_pSeries
system_call_pSeries:
HMT_MEDIUM
+BEGIN_FTR_SECTION
+ cmpdi r0,0x1ebe
+ beq- 1f
+END_FTR_SECTION_IFSET(CPU_FTR_REAL_LE)
mr r9,r13
- mfmsr r10
mfspr r13,SPRN_SPRG3
mfspr r11,SPRN_SRR0
- clrrdi r12,r13,32
- oris r12,r12,system_call_common@h
- ori r12,r12,system_call_common@l
+ ld r12,PACAKBASE(r13)
+ ld r10,PACAKMSR(r13)
+ LOAD_HANDLER(r12, system_call_entry)
mtspr SPRN_SRR0,r12
- ori r10,r10,MSR_IR|MSR_DR|MSR_RI
mfspr r12,SPRN_SRR1
mtspr SPRN_SRR1,r10
rfid
b . /* prevent speculative execution */
+/* Fast LE/BE switch system call */
+1: mfspr r12,SPRN_SRR1
+ xori r12,r12,MSR_LE
+ mtspr SPRN_SRR1,r12
+ rfid /* return to userspace */
+ b .
+
STD_EXCEPTION_PSERIES(0xd00, single_step)
STD_EXCEPTION_PSERIES(0xe00, trap_0e)
. = 0xf00
b performance_monitor_pSeries
- STD_EXCEPTION_PSERIES(0xf20, altivec_unavailable)
+ . = 0xf20
+ b altivec_unavailable_pSeries
+
+ . = 0xf40
+ b vsx_unavailable_pSeries
#ifdef CONFIG_CBE_RAS
HSTD_EXCEPTION_PSERIES(0x1200, cbe_system_error)
/* moved from 0xf00 */
STD_EXCEPTION_PSERIES(., performance_monitor)
+ STD_EXCEPTION_PSERIES(., altivec_unavailable)
+ STD_EXCEPTION_PSERIES(., vsx_unavailable)
+
+/*
+ * An interrupt came in while soft-disabled; clear EE in SRR1,
+ * clear paca->hard_enabled and return.
+ */
+masked_interrupt:
+ stb r10,PACAHARDIRQEN(r13)
+ mtcrf 0x80,r9
+ ld r9,PACA_EXGEN+EX_R9(r13)
+ mfspr r10,SPRN_SRR1
+ rldicl r10,r10,48,1 /* clear MSR_EE */
+ rotldi r10,r10,16
+ mtspr SPRN_SRR1,r10
+ ld r10,PACA_EXGEN+EX_R10(r13)
+ mfspr r13,SPRN_SPRG1
+ rfid
+ b .
.align 7
-_GLOBAL(do_stab_bolted_pSeries)
+do_stab_bolted_pSeries:
mtcrf 0x80,r12
mfspr r12,SPRN_SPRG2
EXCEPTION_PROLOG_PSERIES(PACA_EXSLB, .do_stab_bolted)
-/*
- * We have some room here we use that to put
- * the peries slb miss user trampoline code so it's reasonably
- * away from slb_miss_user_common to avoid problems with rfid
- *
- * This is used for when the SLB miss handler has to go virtual,
- * which doesn't happen for now anymore but will once we re-implement
- * dynamic VSIDs for shared page tables
- */
-#ifdef __DISABLED__
-slb_miss_user_pseries:
- std r10,PACA_EXGEN+EX_R10(r13)
- std r11,PACA_EXGEN+EX_R11(r13)
- std r12,PACA_EXGEN+EX_R12(r13)
- mfspr r10,SPRG1
- ld r11,PACA_EXSLB+EX_R9(r13)
- ld r12,PACA_EXSLB+EX_R3(r13)
- std r10,PACA_EXGEN+EX_R13(r13)
- std r11,PACA_EXGEN+EX_R9(r13)
- std r12,PACA_EXGEN+EX_R3(r13)
- clrrdi r12,r13,32
- mfmsr r10
- mfspr r11,SRR0 /* save SRR0 */
- ori r12,r12,slb_miss_user_common@l /* virt addr of handler */
- ori r10,r10,MSR_IR|MSR_DR|MSR_RI
- mtspr SRR0,r12
- mfspr r12,SRR1 /* and SRR1 */
- mtspr SRR1,r10
- rfid
- b . /* prevent spec. execution */
-#endif /* __DISABLED__ */
-
+#ifdef CONFIG_PPC_PSERIES
/*
* Vectors for the FWNMI option. Share common code.
*/
mtspr SPRN_SPRG1,r13 /* save r13 */
EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common)
-#ifdef CONFIG_PPC_ISERIES
-/*** ISeries-LPAR interrupt handlers ***/
-
- STD_EXCEPTION_ISERIES(0x200, machine_check, PACA_EXMC)
-
- .globl data_access_iSeries
-data_access_iSeries:
- mtspr SPRN_SPRG1,r13
-BEGIN_FTR_SECTION
- mtspr SPRN_SPRG2,r12
- mfspr r13,SPRN_DAR
- mfspr r12,SPRN_DSISR
- srdi r13,r13,60
- rlwimi r13,r12,16,0x20
- mfcr r12
- cmpwi r13,0x2c
- beq .do_stab_bolted_iSeries
- mtcrf 0x80,r12
- mfspr r12,SPRN_SPRG2
-END_FTR_SECTION_IFCLR(CPU_FTR_SLB)
- EXCEPTION_PROLOG_ISERIES_1(PACA_EXGEN)
- EXCEPTION_PROLOG_ISERIES_2
- b data_access_common
-
-.do_stab_bolted_iSeries:
- mtcrf 0x80,r12
- mfspr r12,SPRN_SPRG2
- EXCEPTION_PROLOG_ISERIES_1(PACA_EXSLB)
- EXCEPTION_PROLOG_ISERIES_2
- b .do_stab_bolted
-
- .globl data_access_slb_iSeries
-data_access_slb_iSeries:
- mtspr SPRN_SPRG1,r13 /* save r13 */
- mfspr r13,SPRN_SPRG3 /* get paca address into r13 */
- std r3,PACA_EXSLB+EX_R3(r13)
- mfspr r3,SPRN_DAR
- std r9,PACA_EXSLB+EX_R9(r13)
- mfcr r9
-#ifdef __DISABLED__
- cmpdi r3,0
- bge slb_miss_user_iseries
-#endif
- std r10,PACA_EXSLB+EX_R10(r13)
- std r11,PACA_EXSLB+EX_R11(r13)
- std r12,PACA_EXSLB+EX_R12(r13)
- mfspr r10,SPRN_SPRG1
- std r10,PACA_EXSLB+EX_R13(r13)
- ld r12,PACALPPACAPTR(r13)
- ld r12,LPPACASRR1(r12)
- b .slb_miss_realmode
-
- STD_EXCEPTION_ISERIES(0x400, instruction_access, PACA_EXGEN)
-
- .globl instruction_access_slb_iSeries
-instruction_access_slb_iSeries:
- mtspr SPRN_SPRG1,r13 /* save r13 */
- mfspr r13,SPRN_SPRG3 /* get paca address into r13 */
- std r3,PACA_EXSLB+EX_R3(r13)
- ld r3,PACALPPACAPTR(r13)
- ld r3,LPPACASRR0(r3) /* get SRR0 value */
- std r9,PACA_EXSLB+EX_R9(r13)
- mfcr r9
-#ifdef __DISABLED__
- cmpdi r3,0
- bge .slb_miss_user_iseries
-#endif
- std r10,PACA_EXSLB+EX_R10(r13)
- std r11,PACA_EXSLB+EX_R11(r13)
- std r12,PACA_EXSLB+EX_R12(r13)
- mfspr r10,SPRN_SPRG1
- std r10,PACA_EXSLB+EX_R13(r13)
- ld r12,PACALPPACAPTR(r13)
- ld r12,LPPACASRR1(r12)
- b .slb_miss_realmode
+#endif /* CONFIG_PPC_PSERIES */
#ifdef __DISABLED__
-slb_miss_user_iseries:
+/*
+ * This is used for when the SLB miss handler has to go virtual,
+ * which doesn't happen for now anymore but will once we re-implement
+ * dynamic VSIDs for shared page tables
+ */
+slb_miss_user_pseries:
std r10,PACA_EXGEN+EX_R10(r13)
std r11,PACA_EXGEN+EX_R11(r13)
std r12,PACA_EXGEN+EX_R12(r13)
std r10,PACA_EXGEN+EX_R13(r13)
std r11,PACA_EXGEN+EX_R9(r13)
std r12,PACA_EXGEN+EX_R3(r13)
- EXCEPTION_PROLOG_ISERIES_2
- b slb_miss_user_common
-#endif
-
- MASKABLE_EXCEPTION_ISERIES(0x500, hardware_interrupt)
- STD_EXCEPTION_ISERIES(0x600, alignment, PACA_EXGEN)
- STD_EXCEPTION_ISERIES(0x700, program_check, PACA_EXGEN)
- STD_EXCEPTION_ISERIES(0x800, fp_unavailable, PACA_EXGEN)
- MASKABLE_EXCEPTION_ISERIES(0x900, decrementer)
- STD_EXCEPTION_ISERIES(0xa00, trap_0a, PACA_EXGEN)
- STD_EXCEPTION_ISERIES(0xb00, trap_0b, PACA_EXGEN)
-
- .globl system_call_iSeries
-system_call_iSeries:
- mr r9,r13
- mfspr r13,SPRN_SPRG3
- EXCEPTION_PROLOG_ISERIES_2
- b system_call_common
-
- STD_EXCEPTION_ISERIES( 0xd00, single_step, PACA_EXGEN)
- STD_EXCEPTION_ISERIES( 0xe00, trap_0e, PACA_EXGEN)
- STD_EXCEPTION_ISERIES( 0xf00, performance_monitor, PACA_EXGEN)
-
- .globl system_reset_iSeries
-system_reset_iSeries:
- mfspr r13,SPRN_SPRG3 /* Get paca address */
- mfmsr r24
- ori r24,r24,MSR_RI
- mtmsrd r24 /* RI on */
- lhz r24,PACAPACAINDEX(r13) /* Get processor # */
- cmpwi 0,r24,0 /* Are we processor 0? */
- beq .__start_initialization_iSeries /* Start up the first processor */
- mfspr r4,SPRN_CTRLF
- li r5,CTRL_RUNLATCH /* Turn off the run light */
- andc r4,r4,r5
- mtspr SPRN_CTRLT,r4
+ clrrdi r12,r13,32
+ mfmsr r10
+ mfspr r11,SRR0 /* save SRR0 */
+ ori r12,r12,slb_miss_user_common@l /* virt addr of handler */
+ ori r10,r10,MSR_IR|MSR_DR|MSR_RI
+ mtspr SRR0,r12
+ mfspr r12,SRR1 /* and SRR1 */
+ mtspr SRR1,r10
+ rfid
+ b . /* prevent spec. execution */
+#endif /* __DISABLED__ */
-1:
- HMT_LOW
-#ifdef CONFIG_SMP
- lbz r23,PACAPROCSTART(r13) /* Test if this processor
- * should start */
- sync
- LOAD_REG_IMMEDIATE(r3,current_set)
- sldi r28,r24,3 /* get current_set[cpu#] */
- ldx r3,r3,r28
- addi r1,r3,THREAD_SIZE
- subi r1,r1,STACK_FRAME_OVERHEAD
+ .align 7
+ .globl __end_interrupts
+__end_interrupts:
- cmpwi 0,r23,0
- beq iSeries_secondary_smp_loop /* Loop until told to go */
- bne .__secondary_start /* Loop until told to go */
-iSeries_secondary_smp_loop:
- /* Let the Hypervisor know we are alive */
- /* 8002 is a call to HvCallCfg::getLps, a harmless Hypervisor function */
- lis r3,0x8002
- rldicr r3,r3,32,15 /* r0 = (r3 << 32) & 0xffff000000000000 */
-#else /* CONFIG_SMP */
- /* Yield the processor. This is required for non-SMP kernels
- which are running on multi-threaded machines. */
- lis r3,0x8000
- rldicr r3,r3,32,15 /* r3 = (r3 << 32) & 0xffff000000000000 */
- addi r3,r3,18 /* r3 = 0x8000000000000012 which is "yield" */
- li r4,0 /* "yield timed" */
- li r5,-1 /* "yield forever" */
-#endif /* CONFIG_SMP */
- li r0,-1 /* r0=-1 indicates a Hypervisor call */
- sc /* Invoke the hypervisor via a system call */
- mfspr r13,SPRN_SPRG3 /* Put r13 back ???? */
- b 1b /* If SMP not configured, secondaries
- * loop forever */
-
- .globl decrementer_iSeries_masked
-decrementer_iSeries_masked:
- /* We may not have a valid TOC pointer in here. */
- li r11,1
- ld r12,PACALPPACAPTR(r13)
- stb r11,LPPACADECRINT(r12)
- LOAD_REG_IMMEDIATE(r12, tb_ticks_per_jiffy)
- lwz r12,0(r12)
- mtspr SPRN_DEC,r12
- /* fall through */
-
- .globl hardware_interrupt_iSeries_masked
-hardware_interrupt_iSeries_masked:
- mtcrf 0x80,r9 /* Restore regs */
- ld r12,PACALPPACAPTR(r13)
- ld r11,LPPACASRR0(r12)
- ld r12,LPPACASRR1(r12)
- mtspr SPRN_SRR0,r11
- mtspr SPRN_SRR1,r12
- ld r9,PACA_EXGEN+EX_R9(r13)
- ld r10,PACA_EXGEN+EX_R10(r13)
- ld r11,PACA_EXGEN+EX_R11(r13)
- ld r12,PACA_EXGEN+EX_R12(r13)
- ld r13,PACA_EXGEN+EX_R13(r13)
- rfid
- b . /* prevent speculative execution */
-#endif /* CONFIG_PPC_ISERIES */
+/*
+ * Code from here down to __end_handlers is invoked from the
+ * exception prologs above. Because the prologs assemble the
+ * addresses of these handlers using the LOAD_HANDLER macro,
+ * which uses an addi instruction, these handlers must be in
+ * the first 32k of the kernel image.
+ */
/*** Common interrupt handlers ***/
STD_EXCEPTION_COMMON(0x1800, cbe_thermal, .cbe_thermal_exception)
#endif /* CONFIG_CBE_RAS */
+ .align 7
+system_call_entry:
+ b system_call_common
+
/*
* Here we have detected that the kernel stack pointer is bad.
* R9 contains the saved CR, r13 points to the paca,
SAVE_2GPRS(7,r1)
SAVE_10GPRS(12,r1)
SAVE_10GPRS(22,r1)
+ lhz r12,PACA_TRAP_SAVE(r13)
+ std r12,_TRAP(r1)
addi r11,r1,INT_FRAME_SIZE
std r11,0(r1)
li r12,0
b 1b
/*
- * Return from an exception with minimal checks.
- * The caller is assumed to have done EXCEPTION_PROLOG_COMMON.
- * If interrupts have been enabled, or anything has been
- * done that might have changed the scheduling status of
- * any task or sent any task a signal, you should use
- * ret_from_except or ret_from_except_lite instead of this.
- */
- .globl fast_exception_return
-fast_exception_return:
- ld r12,_MSR(r1)
- ld r11,_NIP(r1)
- andi. r3,r12,MSR_RI /* check if RI is set */
- beq- unrecov_fer
-
-#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- andi. r3,r12,MSR_PR
- beq 2f
- ACCOUNT_CPU_USER_EXIT(r3, r4)
-2:
-#endif
-
- ld r3,_CCR(r1)
- ld r4,_LINK(r1)
- ld r5,_CTR(r1)
- ld r6,_XER(r1)
- mtcr r3
- mtlr r4
- mtctr r5
- mtxer r6
- REST_GPR(0, r1)
- REST_8GPRS(2, r1)
-
- mfmsr r10
- clrrdi r10,r10,2 /* clear RI (LE is 0 already) */
- mtmsrd r10,1
-
- mtspr SPRN_SRR1,r12
- mtspr SPRN_SRR0,r11
- REST_4GPRS(10, r1)
- ld r1,GPR1(r1)
- rfid
- b . /* prevent speculative execution */
-
-unrecov_fer:
- bl .save_nvgprs
-1: addi r3,r1,STACK_FRAME_OVERHEAD
- bl .unrecoverable_exception
- b 1b
-
-/*
* Here r13 points to the paca, r9 contains the saved CR,
* SRR0 and SRR1 are saved in r11 and r12,
* r9 - r13 are saved in paca->exgen.
li r5,0
std r4,_DAR(r1)
std r5,_DSISR(r1)
- b .handle_page_fault
+ b handle_page_fault
unrecov_user_slb:
EXCEPTION_PROLOG_COMMON(0x4200, PACA_EXGEN)
*/
_GLOBAL(slb_miss_realmode)
mflr r10
+#ifdef CONFIG_RELOCATABLE
+ mtctr r11
+#endif
stw r9,PACA_EXSLB+EX_CCR(r13) /* save CR in exc. frame */
std r10,PACA_EXSLB+EX_LR(r13) /* save LR */
ld r3,PACA_EXSLB+EX_R3(r13)
lwz r9,PACA_EXSLB+EX_CCR(r13) /* get saved CR */
#ifdef CONFIG_PPC_ISERIES
+BEGIN_FW_FTR_SECTION
ld r11,PACALPPACAPTR(r13)
ld r11,LPPACASRR0(r11) /* get SRR0 value */
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif /* CONFIG_PPC_ISERIES */
mtlr r10
andi. r10,r12,MSR_RI /* check for unrecoverable exception */
- beq- unrecov_slb
+ beq- 2f
.machine push
.machine "power4"
.machine pop
#ifdef CONFIG_PPC_ISERIES
+BEGIN_FW_FTR_SECTION
mtspr SPRN_SRR0,r11
mtspr SPRN_SRR1,r12
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif /* CONFIG_PPC_ISERIES */
ld r9,PACA_EXSLB+EX_R9(r13)
ld r10,PACA_EXSLB+EX_R10(r13)
rfid
b . /* prevent speculative execution */
+2:
+#ifdef CONFIG_PPC_ISERIES
+BEGIN_FW_FTR_SECTION
+ b unrecov_slb
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
+#endif /* CONFIG_PPC_ISERIES */
+ mfspr r11,SPRN_SRR0
+ ld r10,PACAKBASE(r13)
+ LOAD_HANDLER(r10,unrecov_slb)
+ mtspr SPRN_SRR0,r10
+ ld r10,PACAKMSR(r13)
+ mtspr SPRN_SRR1,r10
+ rfid
+ b .
+
unrecov_slb:
EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB)
DISABLE_INTS
FINISH_NAP
hardware_interrupt_entry:
DISABLE_INTS
+BEGIN_FTR_SECTION
bl .ppc64_runlatch_on
+END_FTR_SECTION_IFSET(CPU_FTR_CTRL)
addi r3,r1,STACK_FRAME_OVERHEAD
bl .do_IRQ
b .ret_from_except_lite
.globl fp_unavailable_common
fp_unavailable_common:
EXCEPTION_PROLOG_COMMON(0x800, PACA_EXGEN)
- bne .load_up_fpu /* if from user, just load it up */
+ bne 1f /* if from user, just load it up */
bl .save_nvgprs
addi r3,r1,STACK_FRAME_OVERHEAD
ENABLE_INTS
bl .kernel_fp_unavailable_exception
BUG_OPCODE
+1: bl .load_up_fpu
+ b fast_exception_return
.align 7
.globl altivec_unavailable_common
EXCEPTION_PROLOG_COMMON(0xf20, PACA_EXGEN)
#ifdef CONFIG_ALTIVEC
BEGIN_FTR_SECTION
- bne .load_up_altivec /* if from user, just load it up */
+ beq 1f
+ bl .load_up_altivec
+ b fast_exception_return
+1:
END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
#endif
bl .save_nvgprs
bl .altivec_unavailable_exception
b .ret_from_except
+ .align 7
+ .globl vsx_unavailable_common
+vsx_unavailable_common:
+ EXCEPTION_PROLOG_COMMON(0xf40, PACA_EXGEN)
+#ifdef CONFIG_VSX
+BEGIN_FTR_SECTION
+ bne .load_up_vsx
+1:
+END_FTR_SECTION_IFSET(CPU_FTR_VSX)
+#endif
+ bl .save_nvgprs
+ addi r3,r1,STACK_FRAME_OVERHEAD
+ ENABLE_INTS
+ bl .vsx_unavailable_exception
+ b .ret_from_except
+
+ .align 7
+ .globl __end_handlers
+__end_handlers:
+
+/*
+ * Return from an exception with minimal checks.
+ * The caller is assumed to have done EXCEPTION_PROLOG_COMMON.
+ * If interrupts have been enabled, or anything has been
+ * done that might have changed the scheduling status of
+ * any task or sent any task a signal, you should use
+ * ret_from_except or ret_from_except_lite instead of this.
+ */
+fast_exc_return_irq: /* restores irq state too */
+ ld r3,SOFTE(r1)
+ TRACE_AND_RESTORE_IRQ(r3);
+ ld r12,_MSR(r1)
+ rldicl r4,r12,49,63 /* get MSR_EE to LSB */
+ stb r4,PACAHARDIRQEN(r13) /* restore paca->hard_enabled */
+ b 1f
+
+ .globl fast_exception_return
+fast_exception_return:
+ ld r12,_MSR(r1)
+1: ld r11,_NIP(r1)
+ andi. r3,r12,MSR_RI /* check if RI is set */
+ beq- unrecov_fer
+
+#ifdef CONFIG_VIRT_CPU_ACCOUNTING
+ andi. r3,r12,MSR_PR
+ beq 2f
+ ACCOUNT_CPU_USER_EXIT(r3, r4)
+2:
+#endif
+
+ ld r3,_CCR(r1)
+ ld r4,_LINK(r1)
+ ld r5,_CTR(r1)
+ ld r6,_XER(r1)
+ mtcr r3
+ mtlr r4
+ mtctr r5
+ mtxer r6
+ REST_GPR(0, r1)
+ REST_8GPRS(2, r1)
+
+ mfmsr r10
+ rldicl r10,r10,48,1 /* clear EE */
+ rldicr r10,r10,16,61 /* clear RI (LE is 0 already) */
+ mtmsrd r10,1
+
+ mtspr SPRN_SRR1,r12
+ mtspr SPRN_SRR0,r11
+ REST_4GPRS(10, r1)
+ ld r1,GPR1(r1)
+ rfid
+ b . /* prevent speculative execution */
+
+unrecov_fer:
+ bl .save_nvgprs
+1: addi r3,r1,STACK_FRAME_OVERHEAD
+ bl .unrecoverable_exception
+ b 1b
+
#ifdef CONFIG_ALTIVEC
/*
* load_up_altivec(unused, unused, tsk)
std r4,0(r3)
#endif /* CONFIG_SMP */
/* restore registers and return */
- b fast_exception_return
+ blr
#endif /* CONFIG_ALTIVEC */
+#ifdef CONFIG_VSX
+/*
+ * load_up_vsx(unused, unused, tsk)
+ * Disable VSX for the task which had it previously,
+ * and save its vector registers in its thread_struct.
+ * Reuse the fp and vsx saves, but first check to see if they have
+ * been saved already.
+ * On entry: r13 == 'current' && last_task_used_vsx != 'current'
+ */
+_STATIC(load_up_vsx)
+/* Load FP and VSX registers if they haven't been done yet */
+ andi. r5,r12,MSR_FP
+ beql+ load_up_fpu /* skip if already loaded */
+ andis. r5,r12,MSR_VEC@h
+ beql+ load_up_altivec /* skip if already loaded */
+
+#ifndef CONFIG_SMP
+ ld r3,last_task_used_vsx@got(r2)
+ ld r4,0(r3)
+ cmpdi 0,r4,0
+ beq 1f
+ /* Disable VSX for last_task_used_vsx */
+ addi r4,r4,THREAD
+ ld r5,PT_REGS(r4)
+ ld r4,_MSR-STACK_FRAME_OVERHEAD(r5)
+ lis r6,MSR_VSX@h
+ andc r6,r4,r6
+ std r6,_MSR-STACK_FRAME_OVERHEAD(r5)
+1:
+#endif /* CONFIG_SMP */
+ ld r4,PACACURRENT(r13)
+ addi r4,r4,THREAD /* Get THREAD */
+ li r6,1
+ stw r6,THREAD_USED_VSR(r4) /* ... also set thread used vsr */
+ /* enable use of VSX after return */
+ oris r12,r12,MSR_VSX@h
+ std r12,_MSR(r1)
+#ifndef CONFIG_SMP
+ /* Update last_task_used_math to 'current' */
+ ld r4,PACACURRENT(r13)
+ std r4,0(r3)
+#endif /* CONFIG_SMP */
+ b fast_exception_return
+#endif /* CONFIG_VSX */
+
/*
* Hash table stuff
*/
.align 7
-_GLOBAL(do_hash_page)
+_STATIC(do_hash_page)
std r3,_DAR(r1)
std r4,_DSISR(r1)
andis. r0,r4,0xa450 /* weird error? */
- bne- .handle_page_fault /* if not, try to insert a HPTE */
+ bne- handle_page_fault /* if not, try to insert a HPTE */
BEGIN_FTR_SECTION
andis. r0,r4,0x0020 /* Is it a segment table fault? */
- bne- .do_ste_alloc /* If so handle it */
+ bne- do_ste_alloc /* If so handle it */
END_FTR_SECTION_IFCLR(CPU_FTR_SLB)
/*
+ * On iSeries, we soft-disable interrupts here, then
+ * hard-enable interrupts so that the hash_page code can spin on
+ * the hash_table_lock without problems on a shared processor.
+ */
+ DISABLE_INTS
+
+ /*
+ * Currently, trace_hardirqs_off() will be called by DISABLE_INTS
+ * and will clobber volatile registers when irq tracing is enabled
+ * so we need to reload them. It may be possible to be smarter here
+ * and move the irq tracing elsewhere but let's keep it simple for
+ * now
+ */
+#ifdef CONFIG_TRACE_IRQFLAGS
+ ld r3,_DAR(r1)
+ ld r4,_DSISR(r1)
+ ld r5,_TRAP(r1)
+ ld r12,_MSR(r1)
+ clrrdi r5,r5,4
+#endif /* CONFIG_TRACE_IRQFLAGS */
+ /*
* We need to set the _PAGE_USER bit if MSR_PR is set or if we are
* accessing a userspace segment (even from the kernel). We assume
* kernel addresses always have the high bit set.
rlwimi r4,r5,22+2,31-2,31-2 /* Set _PAGE_EXEC if trap is 0x400 */
/*
- * On iSeries, we soft-disable interrupts here, then
- * hard-enable interrupts so that the hash_page code can spin on
- * the hash_table_lock without problems on a shared processor.
- */
- DISABLE_INTS
-
- /*
* r3 contains the faulting address
* r4 contains the required access permissions
* r5 contains the trap number
bl .hash_page /* build HPTE if possible */
cmpdi r3,0 /* see if hash_page succeeded */
-#ifdef DO_SOFT_DISABLE
+BEGIN_FW_FTR_SECTION
/*
* If we had interrupts soft-enabled at the point where the
* DSI/ISI occurred, and an interrupt came in during hash_page,
* because ret_from_except_lite will check for and handle pending
* interrupts if necessary.
*/
- beq .ret_from_except_lite
+ beq 13f
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
+
+BEGIN_FW_FTR_SECTION
+ /*
+ * Here we have interrupts hard-disabled, so it is sufficient
+ * to restore paca->{soft,hard}_enable and get out.
+ */
+ beq fast_exc_return_irq /* Return from exception on success */
+END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES)
+
/* For a hash failure, we don't bother re-enabling interrupts */
ble- 12f
/*
* hash_page couldn't handle it, set soft interrupt enable back
- * to what it was before the trap. Note that .local_irq_restore
+ * to what it was before the trap. Note that .raw_local_irq_restore
* handles any interrupts pending at this point.
*/
ld r3,SOFTE(r1)
- bl .local_irq_restore
+ TRACE_AND_RESTORE_IRQ_PARTIAL(r3, 11f)
+ bl .raw_local_irq_restore
b 11f
-#else
- beq fast_exception_return /* Return from exception on success */
- ble- 12f /* Failure return from hash_page */
-
- /* fall through */
-#endif
/* Here we have a page fault that hash_page can't handle. */
-_GLOBAL(handle_page_fault)
+handle_page_fault:
ENABLE_INTS
11: ld r4,_DAR(r1)
ld r5,_DSISR(r1)
addi r3,r1,STACK_FRAME_OVERHEAD
bl .do_page_fault
cmpdi r3,0
- beq+ .ret_from_except_lite
+ beq+ 13f
bl .save_nvgprs
mr r5,r3
addi r3,r1,STACK_FRAME_OVERHEAD
bl .bad_page_fault
b .ret_from_except
+13: b .ret_from_except_lite
+
/* We have a page fault that hash_page could handle but HV refused
* the PTE insertion
*/
12: bl .save_nvgprs
+ mr r5,r3
addi r3,r1,STACK_FRAME_OVERHEAD
- lwz r4,_DAR(r1)
+ ld r4,_DAR(r1)
bl .low_hash_fault
b .ret_from_except
/* here we have a segment miss */
-_GLOBAL(do_ste_alloc)
+do_ste_alloc:
bl .ste_allocate /* try to insert stab entry */
cmpdi r3,0
- beq+ fast_exception_return
- b .handle_page_fault
+ bne- handle_page_fault
+ b fast_exception_return
/*
* r13 points to the PACA, r9 contains the saved CR,
/* Calculate VSID */
/* This is a kernel address, so protovsid = ESID */
- ASM_VSID_SCRAMBLE(r11, r9)
+ ASM_VSID_SCRAMBLE(r11, r9, 256M)
rldic r9,r11,12,16 /* r9 = vsid << 12 */
/* Search the primary group for a free entry */
* Space for CPU0's segment table.
*
* On iSeries, the hypervisor must fill in at least one entry before
- * we get control (with relocate on). The address is give to the hv
- * as a page number (see xLparMap in lpardata.c), so this must be at a
+ * we get control (with relocate on). The address is given to the hv
+ * as a page number (see xLparMap below), so this must be at a
* fixed address (the linker can't compute (u64)&initial_stab >>
* PAGE_SHIFT).
*/
initial_stab:
.space 4096
+#ifdef CONFIG_PPC_PSERIES
/*
* Data area reserved for FWNMI option.
* This address (0x7000) is fixed by the RPA.
.= 0x7000
.globl fwnmi_data_area
fwnmi_data_area:
+#endif /* CONFIG_PPC_PSERIES */
/* iSeries does not use the FWNMI stuff, so it is safe to put
* this here, even if we later allow kernels that will boot on
* both pSeries and iSeries */
#ifdef CONFIG_PPC_ISERIES
. = LPARMAP_PHYS
-#include "lparmap.s"
-/*
- * This ".text" is here for old compilers that generate a trailing
- * .note section when compiling .c files to .s
- */
- .text
+ .globl xLparMap
+xLparMap:
+ .quad HvEsidsToMap /* xNumberEsids */
+ .quad HvRangesToMap /* xNumberRanges */
+ .quad STAB0_PAGE /* xSegmentTableOffs */
+ .zero 40 /* xRsvd */
+ /* xEsids (HvEsidsToMap entries of 2 quads) */
+ .quad PAGE_OFFSET_ESID /* xKernelEsid */
+ .quad PAGE_OFFSET_VSID /* xKernelVsid */
+ .quad VMALLOC_START_ESID /* xKernelEsid */
+ .quad VMALLOC_START_VSID /* xKernelVsid */
+ /* xRanges (HvRangesToMap entries of 3 quads) */
+ .quad HvPagesToMap /* xPages */
+ .quad 0 /* xOffset */
+ .quad PAGE_OFFSET_VSID << (SID_SHIFT - HW_PAGE_SHIFT) /* xVPN */
+
#endif /* CONFIG_PPC_ISERIES */
+#ifdef CONFIG_PPC_PSERIES
. = 0x8000
+#endif /* CONFIG_PPC_PSERIES */
/*
- * On pSeries, secondary processors spin in the following code.
+ * On pSeries and most other platforms, secondary processors spin
+ * in the following code.
* At entry, r3 = this processor's number (physical cpu id)
*/
-_GLOBAL(pSeries_secondary_smp_init)
+_GLOBAL(generic_secondary_smp_init)
mr r24,r3
/* turn on 64-bit mode */
bl .enable_64b_mode
- isync
- /* Copy some CPU settings from CPU 0 */
- bl .__restore_cpu_setup
+ /* get the TOC pointer (real address) */
+ bl .relative_toc
/* Set up a paca value for this processor. Since we have the
* physical cpu id in r24, we need to search the pacas to find
* which logical id maps to our physical one.
*/
- LOAD_REG_IMMEDIATE(r13, paca) /* Get base vaddr of paca array */
+ LOAD_REG_ADDR(r13, paca) /* Get base vaddr of paca array */
li r5,0 /* logical cpu id */
1: lhz r6,PACAHWCPUID(r13) /* Load HW procid from paca */
cmpw r6,r24 /* Compare to our id */
3: HMT_LOW
lbz r23,PACAPROCSTART(r13) /* Test if this processor should */
/* start. */
- sync
-
- /* Create a temp kernel stack for use before relocation is on. */
- ld r1,PACAEMERGSP(r13)
- subi r1,r1,STACK_FRAME_OVERHEAD
+#ifndef CONFIG_SMP
+ b 3b /* Never go on non-SMP */
+#else
cmpwi 0,r23,0
-#ifdef CONFIG_SMP
- bne .__secondary_start
-#endif
- b 3b /* Loop until told to go */
-
-#ifdef CONFIG_PPC_ISERIES
-_STATIC(__start_initialization_iSeries)
- /* Clear out the BSS */
- LOAD_REG_IMMEDIATE(r11,__bss_stop)
- LOAD_REG_IMMEDIATE(r8,__bss_start)
- sub r11,r11,r8 /* bss size */
- addi r11,r11,7 /* round up to an even double word */
- rldicl. r11,r11,61,3 /* shift right by 3 */
- beq 4f
- addi r8,r8,-8
- li r0,0
- mtctr r11 /* zero this many doublewords */
-3: stdu r0,8(r8)
- bdnz 3b
-4:
- LOAD_REG_IMMEDIATE(r1,init_thread_union)
- addi r1,r1,THREAD_SIZE
- li r0,0
- stdu r0,-STACK_FRAME_OVERHEAD(r1)
+ beq 3b /* Loop until told to go */
- LOAD_REG_IMMEDIATE(r3,cpu_specs)
- LOAD_REG_IMMEDIATE(r4,cur_cpu_spec)
- li r5,0
- bl .identify_cpu
-
- LOAD_REG_IMMEDIATE(r2,__toc_start)
- addi r2,r2,0x4000
- addi r2,r2,0x4000
+ sync /* order paca.run and cur_cpu_spec */
- bl .iSeries_early_setup
- bl .early_setup
-
- /* relocation is on at this point */
+ /* See if we need to call a cpu state restore handler */
+ LOAD_REG_ADDR(r23, cur_cpu_spec)
+ ld r23,0(r23)
+ ld r23,CPU_SPEC_RESTORE(r23)
+ cmpdi 0,r23,0
+ beq 4f
+ ld r23,0(r23)
+ mtctr r23
+ bctrl
- b .start_here_common
-#endif /* CONFIG_PPC_ISERIES */
+4: /* Create a temp kernel stack for use before relocation is on. */
+ ld r1,PACAEMERGSP(r13)
+ subi r1,r1,STACK_FRAME_OVERHEAD
-#ifdef CONFIG_PPC_MULTIPLATFORM
+ b __secondary_start
+#endif
+/*
+ * Turn the MMU off.
+ * Assumes we're mapped EA == RA if the MMU is on.
+ */
_STATIC(__mmu_off)
mfmsr r3
andi. r0,r3,MSR_IR|MSR_DR
beqlr
+ mflr r4
andc r3,r3,r0
mtspr SPRN_SRR0,r4
mtspr SPRN_SRR1,r3
*
*/
_GLOBAL(__start_initialization_multiplatform)
-#ifdef CONFIG_PPC_MULTIPLATFORM
+ /* Make sure we are running in 64 bits mode */
+ bl .enable_64b_mode
+
+ /* Get TOC pointer (current runtime address) */
+ bl .relative_toc
+
+ /* find out where we are now */
+ bcl 20,31,$+4
+0: mflr r26 /* r26 = runtime addr here */
+ addis r26,r26,(_stext - 0b)@ha
+ addi r26,r26,(_stext - 0b)@l /* current runtime base addr */
+
/*
* Are we booted from a PROM Of-type client-interface ?
*/
cmpldi cr0,r5,0
- bne .__boot_from_prom /* yes -> prom */
-#endif
-
+ beq 1f
+ b .__boot_from_prom /* yes -> prom */
+1:
/* Save parameters */
mr r31,r3
mr r30,r4
- /* Make sure we are running in 64 bits mode */
- bl .enable_64b_mode
-
/* Setup some critical 970 SPRs before switching MMU off */
- bl .__970_cpu_preinit
+ mfspr r0,SPRN_PVR
+ srwi r0,r0,16
+ cmpwi r0,0x39 /* 970 */
+ beq 1f
+ cmpwi r0,0x3c /* 970FX */
+ beq 1f
+ cmpwi r0,0x44 /* 970MP */
+ beq 1f
+ cmpwi r0,0x45 /* 970GX */
+ bne 2f
+1: bl .__cpu_preinit_ppc970
+2:
- /* Switch off MMU if not already */
- LOAD_REG_IMMEDIATE(r4, .__after_prom_start - KERNELBASE)
- add r4,r4,r30
+ /* Switch off MMU if not already off */
bl .__mmu_off
b .__after_prom_start
-#ifdef CONFIG_PPC_MULTIPLATFORM
-_STATIC(__boot_from_prom)
+_INIT_STATIC(__boot_from_prom)
/* Save parameters */
mr r31,r3
mr r30,r4
/*
* Align the stack to 16-byte boundary
* Depending on the size and layout of the ELF sections in the initial
- * boot binary, the stack pointer will be unalignet on PowerMac
+ * boot binary, the stack pointer may be unaligned on PowerMac
*/
rldicr r1,r1,0,59
- /* Make sure we are running in 64 bits mode */
- bl .enable_64b_mode
-
- /* put a relocation offset into r3 */
- bl .reloc_offset
-
- LOAD_REG_IMMEDIATE(r2,__toc_start)
- addi r2,r2,0x4000
- addi r2,r2,0x4000
-
- /* Relocate the TOC from a virt addr to a real addr */
- add r2,r2,r3
+#ifdef CONFIG_RELOCATABLE
+ /* Relocate code for where we are now */
+ mr r3,r26
+ bl .relocate
+#endif
/* Restore parameters */
mr r3,r31
mr r7,r27
/* Do all of the interaction with OF client interface */
+ mr r8,r26
bl .prom_init
/* We never return */
trap
-#endif
-/*
- * At this point, r3 contains the physical address we are running at,
- * returned by prom_init()
- */
_STATIC(__after_prom_start)
+#ifdef CONFIG_RELOCATABLE
+ /* process relocations for the final address of the kernel */
+ lis r25,PAGE_OFFSET@highest /* compute virtual base of kernel */
+ sldi r25,r25,32
+#ifdef CONFIG_CRASH_DUMP
+ lwz r7,__run_at_load-_stext(r26)
+ cmplwi cr0,r7,1 /* kdump kernel ? - stay where we are */
+ bne 1f
+ add r25,r25,r26
+#endif
+1: mr r3,r25
+ bl .relocate
+#endif
/*
- * We need to run with __start at physical address PHYSICAL_START.
+ * We need to run with _stext at physical address PHYSICAL_START.
* This will leave some code in the first 256B of
* real memory, which are reserved for software use.
- * The remainder of the first page is loaded with the fixed
- * interrupt vectors. The next two pages are filled with
- * unknown exception placeholders.
*
* Note: This process overwrites the OF exception vectors.
- * r26 == relocation offset
- * r27 == KERNELBASE
*/
- bl .reloc_offset
- mr r26,r3
- LOAD_REG_IMMEDIATE(r27, KERNELBASE)
-
- LOAD_REG_IMMEDIATE(r3, PHYSICAL_START) /* target addr */
-
- // XXX FIXME: Use phys returned by OF (r30)
- add r4,r27,r26 /* source addr */
- /* current address of _start */
- /* i.e. where we are running */
- /* the source addr */
-
- cmpdi r4,0 /* In some cases the loader may */
- beq .start_here_multiplatform /* have already put us at zero */
- /* so we can skip the copy. */
- LOAD_REG_IMMEDIATE(r5,copy_to_here) /* # bytes of memory to copy */
- sub r5,r5,r27
-
+ li r3,0 /* target addr */
+ mr. r4,r26 /* In some cases the loader may */
+ beq 9f /* have already put us at zero */
li r6,0x100 /* Start offset, the first 0x100 */
/* bytes were copied earlier. */
+#ifdef CONFIG_CRASH_DUMP
+/*
+ * Check if the kernel has to be running as relocatable kernel based on the
+ * variable __run_at_load, if it is set the kernel is treated as relocatable
+ * kernel, otherwise it will be moved to PHYSICAL_START
+ */
+ lwz r7,__run_at_load-_stext(r26)
+ cmplwi cr0,r7,1
+ bne 3f
+
+ li r5,__end_interrupts - _stext /* just copy interrupts */
+ b 5f
+3:
+#endif
+ lis r5,(copy_to_here - _stext)@ha
+ addi r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */
+
bl .copy_and_flush /* copy the first n bytes */
/* this includes the code being */
/* executed here. */
-
- LOAD_REG_IMMEDIATE(r0, 4f) /* Jump to the copy of this code */
- mtctr r0 /* that we just made/relocated */
+ addis r8,r3,(4f - _stext)@ha /* Jump to the copy of this code */
+ addi r8,r8,(4f - _stext)@l /* that we just made */
+ mtctr r8
bctr
-4: LOAD_REG_IMMEDIATE(r5,klimit)
- add r5,r5,r26
- ld r5,0(r5) /* get the value of klimit */
- sub r5,r5,r27
- bl .copy_and_flush /* copy the rest */
- b .start_here_multiplatform
+p_end: .llong _end - _stext
-#endif /* CONFIG_PPC_MULTIPLATFORM */
+4: /* Now copy the rest of the kernel up to _end */
+ addis r5,r26,(p_end - _stext)@ha
+ ld r5,(p_end - _stext)@l(r5) /* get _end */
+5: bl .copy_and_flush /* copy the rest */
+
+9: b .start_here_multiplatform
/*
* Copy routine used to copy the kernel to start at physical address 0
_GLOBAL(copy_and_flush)
addi r5,r5,-8
addi r6,r6,-8
-4: li r0,16 /* Use the least common */
+4: li r0,8 /* Use the smallest common */
/* denominator cache line */
/* size. This results in */
/* extra cache line flushes */
_GLOBAL(pmac_secondary_start)
/* turn on 64-bit mode */
bl .enable_64b_mode
- isync
+
+ /* get TOC pointer (real address) */
+ bl .relative_toc
/* Copy some CPU settings from CPU 0 */
- bl .__restore_cpu_setup
+ bl .__restore_cpu_ppc970
/* pSeries do that early though I don't think we really need it */
mfmsr r3
mtmsrd r3 /* RI on */
/* Set up a paca value for this processor. */
- LOAD_REG_IMMEDIATE(r4, paca) /* Get base vaddr of paca array */
- mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */
+ LOAD_REG_ADDR(r4,paca) /* Get base vaddr of paca array */
+ mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */
add r13,r13,r4 /* for this processor. */
- mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */
+ mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */
/* Create a temp kernel stack for use before relocation is on. */
ld r1,PACAEMERGSP(r13)
subi r1,r1,STACK_FRAME_OVERHEAD
- b .__secondary_start
+ b __secondary_start
#endif /* CONFIG_PPC_PMAC */
* r13 = paca virtual address
* SPRG3 = paca virtual address
*/
-_GLOBAL(__secondary_start)
+ .globl __secondary_start
+__secondary_start:
/* Set thread priority to MEDIUM */
HMT_MEDIUM
- /* Load TOC */
- ld r2,PACATOC(r13)
-
/* Do early setup for that CPU (stab, slb, hash table pointer) */
bl .early_setup_secondary
/* enable MMU and jump to start_secondary */
LOAD_REG_ADDR(r3, .start_secondary_prolog)
LOAD_REG_IMMEDIATE(r4, MSR_KERNEL)
-#ifdef DO_SOFT_DISABLE
+#ifdef CONFIG_PPC_ISERIES
+BEGIN_FW_FTR_SECTION
ori r4,r4,MSR_EE
+ li r8,1
+ stb r8,PACAHARDIRQEN(r13)
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif
+BEGIN_FW_FTR_SECTION
+ stb r7,PACAHARDIRQEN(r13)
+END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES)
+ stb r7,PACASOFTIRQEN(r13)
+
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
rfid
/*
* Running with relocation on at this point. All we want to do is
- * zero the stack back-chain pointer before going into C code.
+ * zero the stack back-chain pointer and get the TOC virtual address
+ * before going into C code.
*/
_GLOBAL(start_secondary_prolog)
+ ld r2,PACATOC(r13)
li r3,0
std r3,0(r1) /* Zero the stack frame pointer */
bl .start_secondary
*/
_GLOBAL(enable_64b_mode)
mfmsr r11 /* grab the current MSR */
- li r12,1
- rldicr r12,r12,MSR_SF_LG,(63-MSR_SF_LG)
- or r11,r11,r12
- li r12,1
- rldicr r12,r12,MSR_ISF_LG,(63-MSR_ISF_LG)
+ li r12,(MSR_SF | MSR_ISF)@highest
+ sldi r12,r12,48
or r11,r11,r12
mtmsrd r11
isync
blr
-#ifdef CONFIG_PPC_MULTIPLATFORM
+/*
+ * This puts the TOC pointer into r2, offset by 0x8000 (as expected
+ * by the toolchain). It computes the correct value for wherever we
+ * are running at the moment, using position-independent code.
+ */
+_GLOBAL(relative_toc)
+ mflr r0
+ bcl 20,31,$+4
+0: mflr r9
+ ld r2,(p_toc - 0b)(r9)
+ add r2,r2,r9
+ mtlr r0
+ blr
+
+p_toc: .llong __toc_start + 0x8000 - 0b
+
/*
* This is where the main kernel code starts.
*/
-_STATIC(start_here_multiplatform)
- /* get a new offset, now that the kernel has moved. */
- bl .reloc_offset
- mr r26,r3
+_INIT_STATIC(start_here_multiplatform)
+ /* set up the TOC (real address) */
+ bl .relative_toc
/* Clear out the BSS. It may have been done in prom_init,
* already but that's irrelevant since prom_init will soon
* be detached from the kernel completely. Besides, we need
* to clear it now for kexec-style entry.
*/
- LOAD_REG_IMMEDIATE(r11,__bss_stop)
- LOAD_REG_IMMEDIATE(r8,__bss_start)
+ LOAD_REG_ADDR(r11,__bss_stop)
+ LOAD_REG_ADDR(r8,__bss_start)
sub r11,r11,r8 /* bss size */
addi r11,r11,7 /* round up to an even double word */
- rldicl. r11,r11,61,3 /* shift right by 3 */
+ srdi. r11,r11,3 /* shift right by 3 */
beq 4f
addi r8,r8,-8
li r0,0
ori r6,r6,MSR_RI
mtmsrd r6 /* RI on */
- /* The following gets the stack and TOC set up with the regs */
+#ifdef CONFIG_RELOCATABLE
+ /* Save the physical address we're running at in kernstart_addr */
+ LOAD_REG_ADDR(r4, kernstart_addr)
+ clrldi r0,r25,2
+ std r0,0(r4)
+#endif
+
+ /* The following gets the stack set up with the regs */
/* pointing to the real addr of the kernel stack. This is */
/* all done to support the C function call below which sets */
/* up the htab. This is done because we have relocated the */
/* kernel but are still running in real mode. */
- LOAD_REG_IMMEDIATE(r3,init_thread_union)
- add r3,r3,r26
+ LOAD_REG_ADDR(r3,init_thread_union)
- /* set up a stack pointer (physical address) */
+ /* set up a stack pointer */
addi r1,r3,THREAD_SIZE
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
- /* set up the TOC (physical address) */
- LOAD_REG_IMMEDIATE(r2,__toc_start)
- addi r2,r2,0x4000
- addi r2,r2,0x4000
- add r2,r2,r26
-
- LOAD_REG_IMMEDIATE(r3, cpu_specs)
- add r3,r3,r26
- LOAD_REG_IMMEDIATE(r4,cur_cpu_spec)
- add r4,r4,r26
- mr r5,r26
- bl .identify_cpu
-
- /* Save some low level config HIDs of CPU0 to be copied to
- * other CPUs later on, or used for suspend/resume
- */
- bl .__save_cpu_setup
- sync
-
/* Do very early kernel initializations, including initial hash table,
* stab and slb setup before we turn on relocation. */
/* Restore parameters passed from prom_init/kexec */
mr r3,r31
- bl .early_setup
+ bl .early_setup /* also sets r13 and SPRG3 */
- LOAD_REG_IMMEDIATE(r3, .start_here_common)
- LOAD_REG_IMMEDIATE(r4, MSR_KERNEL)
+ LOAD_REG_ADDR(r3, .start_here_common)
+ ld r4,PACAKMSR(r13)
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
rfid
b . /* prevent speculative execution */
-#endif /* CONFIG_PPC_MULTIPLATFORM */
/* This is where all platforms converge execution */
-_STATIC(start_here_common)
+_INIT_GLOBAL(start_here_common)
/* relocation is on at this point */
+ std r1,PACAKSAVE(r13)
- /* The following code sets up the SP and TOC now that we are */
- /* running with translation enabled. */
-
- LOAD_REG_IMMEDIATE(r3,init_thread_union)
-
- /* set up the stack */
- addi r1,r3,THREAD_SIZE
- li r0,0
- stdu r0,-STACK_FRAME_OVERHEAD(r1)
-
- /* Apply the CPUs-specific fixups (nop out sections not relevant
- * to this CPU
- */
- li r3,0
- bl .do_cpu_ftr_fixups
-
- /* ptr to current */
- LOAD_REG_IMMEDIATE(r4, init_task)
- std r4,PACACURRENT(r13)
-
- /* Load the TOC */
+ /* Load the TOC (virtual address) */
ld r2,PACATOC(r13)
- std r1,PACAKSAVE(r13)
bl .setup_system
/* Load up the kernel context */
5:
-#ifdef DO_SOFT_DISABLE
li r5,0
- stb r5,PACAPROCENABLED(r13) /* Soft Disabled */
+ stb r5,PACASOFTIRQEN(r13) /* Soft Disabled */
+#ifdef CONFIG_PPC_ISERIES
+BEGIN_FW_FTR_SECTION
mfmsr r5
- ori r5,r5,MSR_EE /* Hard Enabled */
+ ori r5,r5,MSR_EE /* Hard Enabled on iSeries*/
mtmsrd r5
+ li r5,1
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif
+ stb r5,PACAHARDIRQEN(r13) /* Hard Disabled on others */
- bl .start_kernel
+ bl .start_kernel
/* Not reached */
BUG_OPCODE
.globl swapper_pg_dir
swapper_pg_dir:
- .space PAGE_SIZE
-
-/*
- * This space gets a copy of optional info passed to us by the bootstrap
- * Used to pass parameters into the kernel like root=/dev/sda1, etc.
- */
- .globl cmd_line
-cmd_line:
- .space COMMAND_LINE_SIZE
+ .space PGD_TABLE_SIZE