select HAVE_DYNAMIC_FTRACE
select HAVE_FTRACE_MCOUNT_RECORD
select HAVE_FUNCTION_GRAPH_TRACER
- # Horrible source of confusion. Die, die, die ...
- select EMBEDDED
select RTC_LIB if !MACH_LOONGSON
mainmenu "Linux/MIPS Kernel Configuration"
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_ZBOOT_UART16550
- select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
select GCD
select VLYNQ
help
family: TNETD7100, 7200 and 7300.
config BCM47XX
- bool "BCM47XX based boards"
+ bool "Broadcom BCM47XX based boards"
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
config MACH_LOONGSON
bool "Loongson family of machines"
- select SYS_SUPPORTS_ZBOOT_UART16550
+ select SYS_SUPPORTS_ZBOOT
help
This enables the support of Loongson family of machines.
bool "Sibyte BCM91250A-SWARM"
select BOOT_ELF32
select DMA_COHERENT
+ select HAVE_PATA_PLATFORM
select NR_CPUS_DEFAULT_2
select SIBYTE_SB1250
select SWAP_IO_SPACE
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
+ select HAVE_PATA_PLATFORM
select NR_CPUS_DEFAULT_2
select SIBYTE_SB1250
select SWAP_IO_SPACE
config DMA_NONCOHERENT
bool
- select DMA_NEED_PCI_MAP_STATE
+ select NEED_DMA_MAP_STATE
-config DMA_NEED_PCI_MAP_STATE
+config NEED_DMA_MAP_STATE
bool
config SYS_HAS_EARLY_PRINTK
bool "Loongson 2F"
depends on SYS_HAS_CPU_LOONGSON2F
select CPU_LOONGSON2
+ select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
help
The Loongson 2F processor implements the MIPS III instruction set
with many extensions.
select SYS_SUPPORTS_SMP
select NR_CPUS_DEFAULT_16
select WEAK_ORDERING
- select WEAK_REORDERING_BEYOND_LLSC
select CPU_SUPPORTS_HIGHMEM
select CPU_SUPPORTS_HUGEPAGES
help
endchoice
+if CPU_LOONGSON2F
+config CPU_NOP_WORKAROUNDS
+ bool
+
+config CPU_JUMP_WORKAROUNDS
+ bool
+
+config CPU_LOONGSON2F_WORKAROUNDS
+ bool "Loongson 2F Workarounds"
+ default y
+ select CPU_NOP_WORKAROUNDS
+ select CPU_JUMP_WORKAROUNDS
+ help
+ Loongson 2F01 / 2F02 processors have the NOP & JUMP issues which
+ require workarounds. Without workarounds the system may hang
+ unexpectedly. For more information please refer to the gas
+ -mfix-loongson2f-nop and -mfix-loongson2f-jump options.
+
+ Loongson 2F03 and later have fixed these issues and no workarounds
+ are needed. The workarounds have no significant side effect on them
+ but may decrease the performance of the system so this option should
+ be disabled unless the kernel is intended to be run on 2F01 or 2F02
+ systems.
+
+ If unsure, please say Y.
+endif # CPU_LOONGSON2F
+
config SYS_SUPPORTS_ZBOOT
bool
select HAVE_KERNEL_GZIP
select HAVE_KERNEL_BZIP2
select HAVE_KERNEL_LZMA
+ select HAVE_KERNEL_LZO
config SYS_SUPPORTS_ZBOOT_UART16550
bool
config 64BIT_PHYS_ADDR
bool
+config ARCH_PHYS_ADDR_T_64BIT
+ def_bool 64BIT_PHYS_ADDR
+
config CPU_HAS_SMARTMIPS
depends on SYS_SUPPORTS_SMARTMIPS
bool "Support for the SmartMIPS ASE"