#include <asm/atarihw.h>
#include <asm/atariints.h>
-/* Flag that Modem1 port is already initialized and used */
-int atari_MFP_init_done;
-EXPORT_SYMBOL(atari_MFP_init_done);
-
-/* Flag that Modem1 port is already initialized and used */
-int atari_SCC_init_done;
-EXPORT_SYMBOL(atari_SCC_init_done);
-
/* Can be set somewhere, if a SCC master reset has already be done and should
* not be repeated; used by kgdb */
int atari_SCC_reset_done;
static inline void ata_mfp_out(char c)
{
- while (!(mfp.trn_stat & 0x80)) /* wait for tx buf empty */
+ while (!(st_mfp.trn_stat & 0x80)) /* wait for tx buf empty */
barrier();
- mfp.usart_dta = c;
+ st_mfp.usart_dta = c;
}
-void atari_mfp_console_write(struct console *co, const char *str,
- unsigned int count)
+static void atari_mfp_console_write(struct console *co, const char *str,
+ unsigned int count)
{
while (count--) {
if (*str == '\n')
scc.cha_b_data = c;
}
-void atari_scc_console_write(struct console *co, const char *str,
- unsigned int count)
+static void atari_scc_console_write(struct console *co, const char *str,
+ unsigned int count)
{
while (count--) {
if (*str == '\n')
acia.mid_data = c;
}
-void atari_midi_console_write(struct console *co, const char *str,
- unsigned int count)
+static void atari_midi_console_write(struct console *co, const char *str,
+ unsigned int count)
{
while (count--) {
if (*str == '\n')
/* This a some-seconds timeout in case no printer is connected */
unsigned long i = loops_per_jiffy > 1 ? loops_per_jiffy : 10000000/HZ;
- while ((mfp.par_dt_reg & 1) && --i) /* wait for BUSY == L */
+ while ((st_mfp.par_dt_reg & 1) && --i) /* wait for BUSY == L */
;
if (!i)
return 0;
}
}
-#ifdef CONFIG_SERIAL_CONSOLE
+#if 0
int atari_mfp_console_wait_key(struct console *co)
{
- while (!(mfp.rcv_stat & 0x80)) /* wait for rx buf filled */
+ while (!(st_mfp.rcv_stat & 0x80)) /* wait for rx buf filled */
barrier();
- return mfp.usart_dta;
+ return st_mfp.usart_dta;
}
int atari_scc_console_wait_key(struct console *co)
* SCC serial ports. They're used by the debugging interface, kgdb, and the
* serial console code.
*/
-#ifndef CONFIG_SERIAL_CONSOLE
static void __init atari_init_mfp_port(int cflag)
-#else
-void atari_init_mfp_port(int cflag)
-#endif
{
/*
* timer values for 1200...115200 bps; > 38400 select 110, 134, or 150
baud = B9600; /* use default 9600bps for non-implemented rates */
baud -= B1200; /* baud_table[] starts at 1200bps */
- mfp.trn_stat &= ~0x01; /* disable TX */
- mfp.usart_ctr = parity | csize | 0x88; /* 1:16 clk mode, 1 stop bit */
- mfp.tim_ct_cd &= 0x70; /* stop timer D */
- mfp.tim_dt_d = baud_table[baud];
- mfp.tim_ct_cd |= 0x01; /* start timer D, 1:4 */
- mfp.trn_stat |= 0x01; /* enable TX */
-
- atari_MFP_init_done = 1;
+ st_mfp.trn_stat &= ~0x01; /* disable TX */
+ st_mfp.usart_ctr = parity | csize | 0x88; /* 1:16 clk mode, 1 stop bit */
+ st_mfp.tim_ct_cd &= 0x70; /* stop timer D */
+ st_mfp.tim_dt_d = baud_table[baud];
+ st_mfp.tim_ct_cd |= 0x01; /* start timer D, 1:4 */
+ st_mfp.trn_stat |= 0x01; /* enable TX */
}
#define SCC_WRITE(reg, val) \
MFPDELAY(); \
} while (0)
-#ifndef CONFIG_SERIAL_CONSOLE
static void __init atari_init_scc_port(int cflag)
-#else
-void atari_init_scc_port(int cflag)
-#endif
{
extern int atari_SCC_reset_done;
static int clksrc_table[9] =
SCC_WRITE(5, reg5 | 8);
atari_SCC_reset_done = 1;
- atari_SCC_init_done = 1;
}
-#ifndef CONFIG_SERIAL_CONSOLE
static void __init atari_init_midi_port(int cflag)
-#else
-void atari_init_midi_port(int cflag)
-#endif
{
int baud = cflag & CBAUD;
int csize = ((cflag & CSIZE) == CS8) ? 0x10 : 0x00;